H4JUT-3H930-SWUT-3H930-SW

DANIELS ELECTRONICS LTD. TM MT-3 RADIO SYSTEMS PAGING MODULATOR INSTRUCTION MANUAL CI-PM-3 Covers models: CI-PM-3-00 Copyright © 2002 Daniels Electronics Ltd. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or other wise, without the prior written consent of Daniels Electronics Ltd. DE™ is a registered trademark of Daniels Electronic Ltd. registered in the United States Patent and Trademark Office. Printing Date: Dec 2002Daniels Electronics Ltd. Issue Date:February 2002Previous Issue Date: Nov 99Victoria, BC Issue:4 Rev APrevious Issue: 3 Part No.:IM55-CIPM3 PRINTED IN CANADA DANIELS ELECTRONICS LTD TM iiCI-PM-3 Paging Modulator Instruction Manual Reviewed By: NOTE: The user's authority to operate this equipment could be revoked through any changes or modifications not expressly approved by Daniels Electronics Ltd. The design of this equipment is subject to change due to continuous development. This equipment may incorporate minor changes in detail from the information contained in this manual. DANIELS ELECTRONICS LTD TM CI-PM-3 Paging Modulator Instruction Manualiii TABLE OF CONTENTS Page 1GENERAL............................................................................................................................ 1-1 1.1Introduction .......................................................................................................... 1-1 1.2Construction ......................................................................................................... 1-2 1.3Printed Circuit Board Numbering Convention...................................................... 1-2 1.4Specifications........................................................................................................ 1-2 1.4.1General Specifications.................................................................................... 1-2 1.4.2CTCSS Decoder/Encoder (Option) ................................................................ 1-4 1.4.3Physical Specifications ................................................................................... 1-5 2THEORY OF OPERATION................................................................................................. 2-1 2.1Paging Signal Path................................................................................................ 2-1 2.1.12-Level Digital Paging .................................................................................... 2-1 2.1.1.1Self Test Circuitry..................................................................................... 2-2 2.1.24-Level Digital Paging .................................................................................... 2-2 2.1.3Analog Paging................................................................................................ 2-3 2.1.4Front Panel Indicator Circuitry ....................................................................... 2-4 2.1.4.1Data Indicator Circuitry............................................................................ 2-4 2.1.4.2Analog / Digital Indicator Circuitry........................................................... 2-4 2.1.4.3LED Power............................................................................................... 2-4 2.2OCXO/PLL .......................................................................................................... 2-5 2.2.1Standard Frequency Reference ....................................................................... 2-5 2.2.2High Stability Frequency Reference ............................................................... 2-5 2.3Configuration Options .......................................................................................... 2-6 2.3.1Simultaneous Broadcasting (2 Level Paging Only)......................................... 2-6 3ALIGNMENT PROCEDURE AND INSTALLATION ...................................................... 3-1 3.1General................................................................................................................. 3-1 3.2Repair Notes ......................................................................................................... 3-1 3.3Recommended Equipment List............................................................................. 3-1 3.4Installation............................................................................................................ 3-2 3.5Alignment............................................................................................................. 3-2 3.6Frequency (Digital Paging) Adjustment................................................................ 3-2 3.7Reference (Analog Paging) Adjustment................................................................ 3-3 3.8Test Data Symmetry Adjustment .......................................................................... 3-3 3.92 And 4 Level Deviation Adjustment..................................................................... 3-3 3.10PLL Setup............................................................................................................. 3-4 3.11Data Delay Setup .................................................................................................. 3-5 3.12Simulcast Delay Setup .......................................................................................... 3-6 DANIELS ELECTRONICS LTD TM ivCI-PM-3 Paging Modulator Instruction Manual ALIGNMENT PROCEDURE AND INSTALLATION CONTINUED 3.13Repeater Configuration......................................................................................... 3-8 3.13.1Base Transmitter Site CI-PM-3 Configuration ............................................... 3-8 3.13.1.1Digital-Only Paging.................................................................................. 3-8 3.13.1.2Analog/Digital Paging.............................................................…

Text truncated - open the document above for the full version.

DANIELS ELECTRONICS LTD. TM MT-3 RADIO SYSTEMS PAGING MODULATOR INSTRUCTION MANUAL CI-PM-3 Covers models: CI-PM-3-00 Copyright © 2002 Daniels Electronics Ltd. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or other wise, without the prior written consent of Daniels Electronics Ltd. DE™ is a registered trademark of Daniels Electronic Ltd. registered in the United States Patent and Trademark Office. Printing Date: Dec 2002Daniels Electronics Ltd. Issue Date:February 2002Previous Issue Date: Nov 99Victoria, BC Issue:4 Rev APrevious Issue: 3 Part No.:IM55-CIPM3 PRINTED IN CANADA DANIELS ELECTRONICS LTD TM iiCI-PM-3 Paging Modulator Instruction Manual Reviewed By: NOTE: The user's authority to operate this equipment could be revoked through any changes or modifications not expressly approved by Daniels Electronics Ltd. The design of this equipment is subject to change due to continuous development. This equipment may incorporate minor changes in detail from the information contained in this manual. DANIELS ELECTRONICS LTD TM CI-PM-3 Paging Modulator Instruction Manualiii TABLE OF CONTENTS Page 1GENERAL............................................................................................................................ 1-1 1.1Introduction .......................................................................................................... 1-1 1.2Construction ......................................................................................................... 1-2 1.3Printed Circuit Board Numbering Convention...................................................... 1-2 1.4Specifications........................................................................................................ 1-2 1.4.1General Specifications.................................................................................... 1-2 1.4.2CTCSS Decoder/Encoder (Option) ................................................................ 1-4 1.4.3Physical Specifications ................................................................................... 1-5 2THEORY OF OPERATION................................................................................................. 2-1 2.1Paging Signal Path................................................................................................ 2-1 2.1.12-Level Digital Paging .................................................................................... 2-1 2.1.1.1Self Test Circuitry..................................................................................... 2-2 2.1.24-Level Digital Paging .................................................................................... 2-2 2.1.3Analog Paging................................................................................................ 2-3 2.1.4Front Panel Indicator Circuitry ....................................................................... 2-4 2.1.4.1Data Indicator Circuitry............................................................................ 2-4 2.1.4.2Analog / Digital Indicator Circuitry........................................................... 2-4 2.1.4.3LED Power............................................................................................... 2-4 2.2OCXO/PLL .......................................................................................................... 2-5 2.2.1Standard Frequency Reference ....................................................................... 2-5 2.2.2High Stability Frequency Reference ............................................................... 2-5 2.3Configuration Options .......................................................................................... 2-6 2.3.1Simultaneous Broadcasting (2 Level Paging Only)......................................... 2-6 3ALIGNMENT PROCEDURE AND INSTALLATION ...................................................... 3-1 3.1General................................................................................................................. 3-1 3.2Repair Notes ......................................................................................................... 3-1 3.3Recommended Equipment List............................................................................. 3-1 3.4Installation............................................................................................................ 3-2 3.5Alignment............................................................................................................. 3-2 3.6Frequency (Digital Paging) Adjustment................................................................ 3-2 3.7Reference (Analog Paging) Adjustment................................................................ 3-3 3.8Test Data Symmetry Adjustment .......................................................................... 3-3 3.92 And 4 Level Deviation Adjustment..................................................................... 3-3 3.10PLL Setup............................................................................................................. 3-4 3.11Data Delay Setup .................................................................................................. 3-5 3.12Simulcast Delay Setup .......................................................................................... 3-6 DANIELS ELECTRONICS LTD TM ivCI-PM-3 Paging Modulator Instruction Manual ALIGNMENT PROCEDURE AND INSTALLATION CONTINUED 3.13Repeater Configuration......................................................................................... 3-8 3.13.1Base Transmitter Site CI-PM-3 Configuration ............................................... 3-8 3.13.1.1Digital-Only Paging.................................................................................. 3-8 3.13.1.2Analog/Digital Paging.............................................................…

Text truncated - open the document above for the full version.

DANIELS ELECTRONICS LTD. TM Telephone: (250) 382-8268 43 ERIE ST., VICTORIA, BC Fax: (250) 382-6139 CANADA, V8V 1P8 E-Mail: [email protected] Website: www.danelec.com RADIO COMMUNICATION MANUFACTURER FCC ID: H4JUT-3H930-S January 21, 2003 Federal Communications Commission 7435 Oakland Mills Road Columbia, Maryland 21046 REQUEST FOR CONFIDENTIALITY Reference: FCC ID: H4JUT-3H930-SW In accordance with 47 CFR§ 0.457 (d) (ii) and pursuant to 47 CFR§ 0.459 (a), Daniels Electronics Ltd requests that the following information pertaining to its UT-3H930-SW Paging Transmitter not be made routinely available to the public: Specific Information: Operational Description (Theory of Operation) Schematic Diagrams & Block diagrams Component Layout Diagrams (including Alignment Location Diagram) Electrical Parts Lists The above-mentioned sections contain trade secret information which is not made routinely available to the public or to our competitors. Disclosure of this information could result in an unfair advantage to our competitors. This information should be treated as confidential for the duration of effectiveness of the Grant of Authorization. Regards, Ron Backlund Engineering Manager Daniels Electronics Ltd. 43 Erie Street Victoria, BC V8V 1P8 Phone: (250) 382-8268 Fax: (250) 382-6139 E-Mail: [email protected] Web: www.danelec.com

Offices in Ottawa (Canada), USA, Norway, England, Germany, Italy, Korea, Taiwan, China and Shanghai January 24, 2003 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, Maryland 21046 USA Nemko Canada Inc. 303 River Road RR #5 Ottawa, Ontario Canada K1V 1H2 Tel: 613-737-9680 Fax: 613-737-9691 Toll Free: 1-800-563-6336 Email: [email protected] Internet: www.nemkoca.com Dear Sir/Madam: Our File Ref. 2W06694 FCC ID: H4JUT-3H930-SW Applicant: Daniels Electronics Ltd. Equipment: UT-3H930-SWB3 Paging Transmitter FCC Confirmation no.: EA439676 We have successfully electronically filed all the required documentation for an application for a certification filing for original equipment in accordance with FCC Part 22 & 90 on the above mentioned equipment. If you require additional information, please do not hesitate to contact me at 1-800-563-6336 (extension 232). Thank you in advance for your assistance in this matter. Sincerely, Ruby Dulmage Submissions Specialist Nemko Canada Inc. [email protected] Encl.

DANIELS ELECTRONICS LTD. TM Telephone: (250) 382-8268 43 ERIE ST., VICTORIA, BC Fax: (250) 382-6139 CANADA, V8V 1P8 E-Mail: [email protected] Website: www.danelec.com RADIO COMMUNICATION MANUFACTURER FCC ID: H4JUT-3H930-SW March 21, 2003 Federal Communications Commission 7435 Oakland Mills Road Columbia, Maryland 21046 REQUEST FOR CONFIDENTIALITY Reference: FCC ID: H4JUT-3H930-SW In accordance with 47 CFR § 0.457 (d) (ii) and pursuant to 47 CFR § 0.459 (a), Daniels Electronics Ltd requests that the following information pertaining to its UT-3H930-SW Paging Transmitter not be made routinely available to the public: Specific Information: a) Operational Description (Theory of Operation); b) Schematic Diagrams (including Component Layout Diagrams and Alignment Location Diagrams); and c) Parts Lists (Electrical Components). The above-mentioned exhibits contain trade secret information which is not made routinely available to the public or to our competitors. Disclosure of this information could result in an unfair advantage to our competitors. This information should be treated as confidential for the duration of effectiveness of the Grant of Authorization. Regards, Ron Backlund Engineering Manager Daniels Electronics Ltd. 43 Erie Street Victoria, BC V8V 1P8 Phone: (250) 382-8268 Fax: (250) 382-6139 E-Mail: [email protected] Web: www.danelec.com

DANIELS ELECTRONICS LTD. MODEL: CANADA #: FCC ID: EQUIPMENT IDENTIFICATION LABEL FORMAT UT-3H930-SWB3 H4JUT-3H930-SW 10001 1/03 FCC ID: H4JUT-3H930-SW UT-3 900 MHz Paging Transmitter VICTORIA , B.C. CANADA SERIAL #: DATE: Dated thisday of21stJanuary 2003 By:Ron Backlund Title: Applicant: Telephone: Engineering Manager Daniels Electronics Ltd. (250) 382-8268 PrintedSignature REDUCE TO 3.10 INCHES 0.77 INCHES 142A-UT3930SW

FRONT PANEL B O T T O M T O P LEFT SIDE COVER EQUIPMENT IDENTIFICATION LABEL LOCATION FCC ID: H4JUT-3H930-SW UT-3 900 MHz Paging Transmitter Dated thisday of21stJanuary 2003 By:Ron Backlund Title: Applicant: Telephone: Engineering Manager Daniels Electronics Ltd. (250) 382-8268 PrintedSignature DANIELS ELECTRONICS LTD. MODEL: CANADA #: FCC ID: UT-3H930-SWB3 H4JUT-3H930-SW 10001 1/03 VICTORIA , B.C. CANADA SERIAL #: DATE: 142A-UT3930SW

DANIELS ELECTRONICS LTD. TM MT-3 RADIO SYSTEMS PAGING MODULATOR INSTRUCTION MANUAL CI-PM-3 Covers models: CI-PM-3-00 Copyright © 2002 Daniels Electronics Ltd. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or other wise, without the prior written consent of Daniels Electronics Ltd. DE™ is a registered trademark of Daniels Electronic Ltd. registered in the United States Patent and Trademark Office. Printing Date: Dec 2002Daniels Electronics Ltd. Issue Date:February 2002Previous Issue Date: Nov 99Victoria, BC Issue:4 Rev APrevious Issue: 3 Part No.:IM55-CIPM3 PRINTED IN CANADA DANIELS ELECTRONICS LTD TM iiCI-PM-3 Paging Modulator Instruction Manual Reviewed By: NOTE: The user's authority to operate this equipment could be revoked through any changes or modifications not expressly approved by Daniels Electronics Ltd. The design of this equipment is subject to change due to continuous development. This equipment may incorporate minor changes in detail from the information contained in this manual. DANIELS ELECTRONICS LTD TM CI-PM-3 Paging Modulator Instruction Manualiii TABLE OF CONTENTS Page 1GENERAL............................................................................................................................ 1-1 1.1Introduction .......................................................................................................... 1-1 1.2Construction ......................................................................................................... 1-2 1.3Printed Circuit Board Numbering Convention...................................................... 1-2 1.4Specifications........................................................................................................ 1-2 1.4.1General Specifications.................................................................................... 1-2 1.4.2CTCSS Decoder/Encoder (Option) ................................................................ 1-4 1.4.3Physical Specifications ................................................................................... 1-5 2THEORY OF OPERATION................................................................................................. 2-1 2.1Paging Signal Path................................................................................................ 2-1 2.1.12-Level Digital Paging .................................................................................... 2-1 2.1.1.1Self Test Circuitry..................................................................................... 2-2 2.1.24-Level Digital Paging .................................................................................... 2-2 2.1.3Analog Paging................................................................................................ 2-3 2.1.4Front Panel Indicator Circuitry ....................................................................... 2-4 2.1.4.1Data Indicator Circuitry............................................................................ 2-4 2.1.4.2Analog / Digital Indicator Circuitry........................................................... 2-4 2.1.4.3LED Power............................................................................................... 2-4 2.2OCXO/PLL .......................................................................................................... 2-5 2.2.1Standard Frequency Reference ....................................................................... 2-5 2.2.2High Stability Frequency Reference ............................................................... 2-5 2.3Configuration Options .......................................................................................... 2-6 2.3.1Simultaneous Broadcasting (2 Level Paging Only)......................................... 2-6 3ALIGNMENT PROCEDURE AND INSTALLATION ...................................................... 3-1 3.1General................................................................................................................. 3-1 3.2Repair Notes ......................................................................................................... 3-1 3.3Recommended Equipment List............................................................................. 3-1 3.4Installation............................................................................................................ 3-2 3.5Alignment............................................................................................................. 3-2 3.6Frequency (Digital Paging) Adjustment................................................................ 3-2 3.7Reference (Analog Paging) Adjustment................................................................ 3-3 3.8Test Data Symmetry Adjustment .......................................................................... 3-3 3.92 And 4 Level Deviation Adjustment..................................................................... 3-3 3.10PLL Setup............................................................................................................. 3-4 3.11Data Delay Setup .................................................................................................. 3-5 3.12Simulcast Delay Setup .......................................................................................... 3-6 DANIELS ELECTRONICS LTD TM ivCI-PM-3 Paging Modulator Instruction Manual ALIGNMENT PROCEDURE AND INSTALLATION CONTINUED 3.13Repeater Configuration......................................................................................... 3-8 3.13.1Base Transmitter Site CI-PM-3 Configuration ............................................... 3-8 3.13.1.1Digital-Only Paging.................................................................................. 3-8 3.13.1.2Analog/Digital Paging.............................................................…

Text truncated - open the document above for the full version.

RF Exposure Warning S= PG 4 πR 2 RF Exposure Warning This transmitting equipment conforms to SAR (Specific Absorption Rate) limits regarding exposure of human beings to radio frequency electromagnetic energy, as defined in the following national and international standards and guidelines: 1. Industry Canada Radio Standards Specification 102 (RSS-102), Evaluation Procedure for Mobile and Portable Radio Transmitters with respect to Health Canada’s Safety Code 6 for Exposure of Humans to Radio Frequency Fields; 2. Health Canada Safety Code 6, Limits of Human Exposure to Radiofrequency Electromagnetic Fields in the Frequency Range from 3 kHz to 300 GHz 1 ; 3. United States Federal Communications Commission, Code of Federal Regulations; 47 CFR Part 1, § 1.1310 Radiofrequency radiation exposure limits; and 4. American National Standards Institute (ANSI) criteria for localized SAR in Section 4.2 of “IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz” 2 . Notes : A. The SAR limit for uncontrolled exposure of persons not classed as RF and microwave exposed workers (including the general public) for transmitter equipment operating below 10 GHz, as defined in the references above, is 2 W/m 2 (0.2 mW/cm 2 ). B. This transmitting equipment is designed for use with an outdoor antenna with a characteristic antenna gain of 10 dBi, typically mounted at a significant height above ground to provide for adequate signal coverage. To ensure that the general public is not exposed to a power density above the recommended limit of 2 W/m 2 (0.2 mW/cm 2 ), the equipment must be installed such that the following minimum safe distances from the antenna are maintained: 10.0 m (32.8 ft) when configured with 250 W PA 6.3 m (20.7 ft) when configured with 100 W PA 1.1 m (3.6 ft) standalone (i.e. no PA) 3 W TX C. The following power density formula has been utilized in determining minimum safe distances: where: S = Power density (in appropriate units, e.g. W/m 2 ) P = Power input to the Antenna (in appropriate units, e.g., W) G = Power gain of the antenna in the direction of interest relative to an isotropic radiator R = Distance to the center of radiation of the antenna (appropriate units, e.g., m) 1 Minister of Public Works and Government Services, Canada 1999, Cat. H46- 2/ 99- 237E, ISBN 0- 662- 28032- 6 2 ANSI/IEEE C95.1–1992, Copyright 1992 by the Institute of Electrical and Electronics Engineers, Inc., New York, New York 10017

DANIELS ELECTRONICS LTD. TM Telephone: (250) 382-8268 43 ERIE ST., VICTORIA, BC FAX: (250) 382-6139 CANADA, V8V 1P8 Website: www.danelec.com RADIO COMMUNICATION MANUFACTURER March 21, 2003 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, Maryland 21046 Declaration of Compliance Reference: FCCID: H4JUT-3H930-SW In accordance with FCC 47 CFR § 1.1307 (b) and FCC OET Bulletin 65 (Edition 97-01), this Daniels Electronics Ltd. transmitter is categorically excluded from routine evaluation or preparing an EA for RF emissions and this exclusion is sufficient basis for assuming compliance with FCC MPE limits. This exclusion is subject to the limits specified in FCC 47 CFR §§ 1.1307 (b) and 1.1310. Daniels Electronics Ltd. has no reason to believe that this excluded transmitter encompasses exceptional characteristics that could cause non-compliance. A warning statement to the user (enclosed) is included with the Instruction Manual for this transmitter. Dated this 21 st day of March, 2003 By: Ron Backlund Engineering Manager Daniels Electronics Ltd. 43 Erie Street Victoria, BC V8V 1P8 Phone: (250) 382-8268 Fax: (250) 382-6139 E-Mail: [email protected] Web: www.danelec.com Enclosure: 1 RF Exposure Warning RF Exposure Warning Exposure to radio frequency (RF) energy has been identified as a potential environmental factor that must be considered before a radio transmitter can be authorized or licensed. The FCC has therefore developed maximum permissible exposure (MPE) limits for field strength and power density, listed in FCC 47 CFR § 1.1310. The FCC has furthermore determined that determination of compliance with these exposure limits, and preparation of an Environmental Assessment (EA) if the limits are exceeded, is necessary only for facilities, operations and transmitters that fall into certain risk categories, listed in FCC 47 CFR § 1.1307 (b), Table 1. All other facilities, operations and transmitters are categorically excluded from making such studies or preparing an EA, except as indicated in FCC 47 CFR §§ 1.1307 (c) and (d). Revised FCC OET Bulletin 65 (Edition 97-01) provides assistance in determining whether a proposed or existing transmitting facility, operation or device complies with RF exposure limits. In accordance with OET Bulletin 65 and FCC 47 CFR § 1.1307 (b), this Daniels Electronics Ltd. transmitter is categorically excluded from routine evaluation or preparing an EA for RF emissions and this exclusion is sufficient basis for assuming compliance with FCC MPE limits. This exclusion is subject to the limits specified in FCC 47 CFR §§ 1.1307 (b) and 1.1310. Daniels Electronics Ltd. has no reason to believe that this excluded transmitter encompasses exceptional characteristics that could cause non-compliance. Notes: The FCC's exposure guidelines constitute exposure limits and not emission limits. They are relevant only to locations that are accessible to workers or members of the public. Such access can be restricted or controlled by appropriate means (i.e. fences, warning signs, etc.). The FCC’s limits apply cumulatively to all sources of RF emissions affecting a given site. Sites exceeding these limits are subject to an EA and must provide test reports indicating compliance. General RF Safety Guidelines and Information Base and Repeater radio transmitters are designed to generate and radiate RF energy by means of an external antenna, typically mounted at a significant height above ground to provide adequate signal coverage. The following antenna installation guidelines are extracted from OET Bulletin 65 Appendix A and must be adhered to to ensure RF exposure compliance: Non-building-mounted Antennas: Height above ground level to lowest point of antenna ≥ 10 m or Power ≤ 1000W ERP (1640 W EIRP) Building-mounted Antennas: Power ≤ 1000 W ERP (1640 W EIRP) The following general RF Safety Guidelines should be observed when working in or around transmitter sites and sources of RF energy: • Do not work on or around any transmitting antenna while RF power is applied. • Before working on an antenna, disable the appropriate transmitter and ensure a “DO NOT USE” or similar sign is placed on or near the PTT or key-up control. • Assume all antennas are active unless specifically indicated otherwise. • Never operate a transmitter with the cover removed. • Ensure all personnel entering a transmitter site have electromagnetic energy awareness training. For more information on RF energy exposure and compliance, please refer to the following references: [1] FCC Code of Regulations; 47 CFR §§ 1.1307 and 1.1310. [2] FCC OET Bulletin 65, Edition 97-01, "Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields". [3] FCC OET Radio Frequency Safety Website: http://ww…

Text truncated - open the document above for the full version.