H5P-FC200BTSDBT/SD Board

1 Ver1.０ July 27, 2006 TOPCON BT/SD Board User’s Manual 2 FCC Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION: Change or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. CAUTION: In order to comply with FCC radio-frequency radiation exposure guidelines for an uncontrolled exposure, this device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense. NOTE: The device to which BT/SD Board is installed must display a FCC ID above. IC Notices CAUSION: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. CAUTION: The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website www.hc-sc.gc.ca/rpb FCC ID: H5P-FC200BTSD IC : 6050AFC200BT 3 (1) Product Overview The BT/SD Board is designed to provide wireless communication ability for the TOPCON’s “FC” Field Controller families to communicate with other Bluetooth devices via the class 2 of the Bluetooth V1.2 protocol. This device is equipped with some type of “FC” Field Controllers before shipping. (2) Features Bluetooth Features Compact wireless data communication module designed for Makitra’s battery-operated tools Low power CSR BlueCore2-Ext Chipset (Bluetooth V1.2) Tx output: 0.5mW Tx and Rx Operation Frequency: 2402-2480 MHz Modulation Method: Frequency Hopping Spectrum Spread (FHSS) / GFSK Number of Channels: 79 (Normal Mode), 79 - 20 (Adaptive Hopping Mode) Channel Intervals: 1 MHz Bit rate: 1 Mbps Packet type in use: DH1 Physical Attributes Size: 48mm (L) x 76mm (W) x 5.5mm (D) Weight: 0.03 Kg Operating Temperature: -20 deg. C to +50 deg. C Power Requirements: 0.3 W @ +3.3 VDC from “FC” Field Controller. 4 (3) Operation To Equip the BT/SD Board with “FC” Field Controller This device is already equipped by TOPCON before shipping. The example of an equipped Field Controller “FC-200” is shown below. Setting up BT/SD Board The FC-200 has Bluetooth transmission function using a built-in BT/SD Board. Information can be exchanged between instruments equipped with the same function using Bluetooth wireless technology. The BT/SD Board is running on the operation system of FC-200, Windows Mobile 5.0 Pocket PC by Microsoft Bluetooth ON/OFF 5 Follow the procedure below to turn on the Bluetooth function. (1) Tap Start > Settings > Connections tab. (2) On the [Wireless Manager] display, tap on the [Bluetooth] icon. (3) Select or clear the Turn on and off Bluetooth check box (4) When the Bluetooth function is turned ON, the wireless LED will flash in green color. Create a Bluetooth partnership Ensure that the two devices are turned on, discoverable, and within close range. (1) Tap Start > Settings > Connections tab. (2) Tap Bluetooth > Devices tab > New Partnership. Your device searches for other devices with Bluetooth capabilities, and displays them in the list. (3) Tap the name of the other device, and tap Next. (4) In Passkey, if you want to use a passkey (recommended for enhanced security), enter a alphanumeric passkey between 1 and 16 characters, and tap Next. Otherwise, leave the passkey blank, and tap Next (5) Enter the same passkey on the other device. (6) Tap Finish Make a device discoverable Other devices with Bluetooth capabilities can detect your device and attempt to beam information to it, establish a partnership, or use a Bluetooth service. (1) Tap Start > Settings > Connections tab. (2) Tap Bluetooth. (3) Select the Turn on Bluetooth check box, and then select the Make this device discoverable to other devices check box Other Bluetooth-enabled devices can now detect your phone and attempt to beam information to it, establish a Bluetooth partnership, or use a Bluetooth service. Enable a Bluetooth beam (1) Tap Start > Settings > Connections tab. (2) Select the Receive all incoming beams check box. (3) When prompted to receive an incoming beam, tap Yes to receive the beamed information. For more “How to and/or Help” on Bluetooth, visit Microsoft! Web site; http://www.microsoft.com/windowsmobile/help/pocketpc/bluetooth.mspx 6 (4) Hints & Tips (1) The BT/SD Board may not work well where Microwave ovens and /or other 2.4GHz ISM devices like wireless LAN are working. Keep RF unit and wireless data receiver away from these devices. (2) If you no longer want your device to be discoverable, clear the Make this device discoverable to other devices check box. (3) For your safety operation, read carefully the tool’s User’s manual before equipping the BT/SD Board to the tool together with this manual and that of the wireless data receiver. (4) The RF unit complies with Part 15 of the FCC Rules and RS-210. Read carefully the FCC notice and/or IC notice at beginning page of …

Text truncated - open the document above for the full version.

TOPCON CORPORATION Compliance Certification Services Certification Division 561F Monterey Road Morgan Hill, CA 95037 To whom it may concern: We, the undersigned, hereby authorize JAPAN QUALITY ASSURANCE ORGANIZATION, to act on our behalf in all manners relating to application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by JAPAN QUALITY ASSURANCE ORGANIZATION on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of IC benefits. In authorizing Japan Quality Assurance Organization as our agent, we still recognize that we are responsible to: a) comply with the relevant provisions of the certification program; b) make all necessary arrangements for the conduct of the evaluation, including provision for examining documentation and access to all areas, records (including internal audit reports) and personnel for the purposes of evaluation (e.g. testing, inspection, assessment, surveillance, reassessment) and resolution of complaints; c) make claims regarding certification only in respect of the scope for which certification has been granted; d) do not use our product certification in such a manner as to bring the Certification Division into disrepute and not make any statement regarding our product certification which the Certification Division may consider misleading or unauthorized; e) upon suspension or cancellation of certification, discontinue use of all TOPCON CORPORATION advertising matter that contains any reference thereto and return any certification documents as required by the Certification Division; f) use certification only to indicate the products are certified as being in conformity with specified standards; g) endeavor to ensure that no certificate or report nor any part thereof is used in a misleading manner; h) ensure that any reference to our product certification in communication media such as documents, brochures or advertising, complies with the requirements of the Certification Division; i) keep a record of all complaints made known to the us relating to the product’s compliance with requirements of the relevant standard and to make these records available to the Certification Division when requested; j) take appropriate action with respect to such complaints and any deficiencies found in products or services that affect compliance with the requirements for certification; k) document the actions taken. This authorization is valid until further written notice from the applicant. Sincerely Yours, Date: August 9, 2006 Signature: Applicant Name: Hiroto Shibuya Title: Engineer Section & Company: 75-1, Hasunuma-cho, Itabashi-Ku, Tokyo 174-8580 Japan TOPCON CORPORATION TOPCON CORPORATION

TOPCON CORPORATION Date: August 9, 2006 Federal Communications Commission Equipment Approval Services Dear Sir/Madame: Pursuant to Section 0.459 of the Commission’s Rules; we, TOPCON CORPORATION (Hiroto Shibuya), hereby request confidentiality as below; 1. Parts List 2. Circuit Diagram 3. Block Diagram The reason of Confidentiality request is that trade secrets and proprietary information are enclosed in the above data, and the public disclosure of the data is harmful for us and will be made unjustifiable benefits to competitors. Sincerely, Signature: Applicant Name: Hiroto Shibuya Title: Engineer Section & Company: 75-1, Hasunuma-cho, Itabashi-Ku, Tokyo 174-8580 Japan TOPCON CORPORATION TOPCON CORPORATION

1 Chris Harvey From: miura-katsunori [[email protected]] Sent: Friday, September 01, 2006 3:18 AM To: [email protected] Cc: 金子 様; [email protected] Subject: Re: Topcon Corporation, FCC ID: H5PBT SD BOARD, Assessment NO.: AN06T6051, Notice#1 Attachments: Exhibit K1 Internal Photographs_R1.pdf; MTA_request.pdf; Exhibit L1 Users Guide_R1.pdf; Exhibit M1 Test Report_R1.pdf; Dec_DH1.pdf; Dec_BT_V1_2.pdf Exhibit K1 Internal Photograph... MTA_request.pdf (46 KB) Exhibit L1 Users Guide_R1.pdf ... Exhibit M1 Test Report_R1.pdf ... Dec_DH1.pdf (43 KB) Dec_BT_V1_2.pdf (43 KB) Dear Chris Harvey Thank you very much for your review, comments and reply of some questions. We are writing to you in reply to your e-mail of August 13, 2006. No. 1. We will revise FCC ID "H5PBT SD Board" in "H5P-FC200BTSD". For 2. We got a photograph from applicant. Please confirm file number "Exhibit K1 Internal Photographs_R1". For 3. We got the declaration sheet from applicant. Please confirm file number "MTA_request". For 4. We got a new Users Guide from applicant. Please confirm file number "Exhibit L1 Users Guide_R1". For 5. We carried out the measurement about the AC Conducted Emission. Please confirm file number "Exhibit M1 Test Report_R1". For 6. We got the declaration sheet from applicant. Please confirm file number "Dec_DH1". For 7. We got the declaration sheet from applicant. Please confirm file number "Dec_BT_V1_2". Sincerely yours, Katsunori Miura * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Katsunori Miura JAPAN QUALITY ASSURANCE ORGANIZATION TESTING DIV. EMC ENGINEERING DEPT. SAFETY & EMC CENTER Tel: +81-3-3416-0193 Fax: +81-3-3416-8290 * * * * * * * * * * * * * * * * * * * * * * * * * * * * * ----- Original Message ----- From: <[email protected]> To: <[email protected]> 2 Cc: <[email protected]>; <[email protected]> Sent: Sunday, August 13, 2006 11:44 PM Subject: Topcon Corporation, FCC ID: H5PBT SD BOARD, Assessment NO.: AN06T6051, Notice#1 > Dear Katsunori Miura: > > I have performed the review of the above referenced application and find that the following items need to be addressed before the review can be completed: > > 1. The Form 731 was submitted for FCC ID: H5PBT SD BOARD (this included the spaces which are not allowed in an FCC ID number) but the exhibits document FCC ID: H5P-FC200BTSD. This is likely that the Product Code field of the Form 731 was completed incorrectly. Please correct the FCC ID number to be consistent (please let me know if you need assistance if the Form 731 needs to be changed). Please note that the FCC ID number is the combination of the Grantee Code (H5P) plus the Product Code. > > 2. Please provide a photograph of the bottom side of the Bluetooth Module and the main circuit under the Bluetooth module. > > 3. This device is a module intended to be used inside other devices. Please provide a completed Modular Approval Cover Letter, indicating the compliance with the 8 requirements for modular approval in accordance with FCC Public Notice DA00-1407. Please clarify if this device is OEM installed, or user installed. This may require updating some of the other exhibits, such as the label, in order to comply with these requirements. > > 4. The Users Manual must include a statement that this device must not be collocated with any other transmitters or antennas. > > 5. The test report indicates that AC Conducted Emissions are not applicable. Please note that AC Conducted emissions are required even if the device receives its power indirectly from the AC mains (for example an AC powered host). The only time when AC Conducted Emissions are not applicable is when the device is always battery powered. Please confirm if this device will always receive power from a battery. > > 6. The test report indicates 'The packet type under the test is DH1 by the applicant request.' What about the other packet types (DH3, DH5, etc.), especially for the dwell time compliance? Please confirm the packet types available in this device and provide compliance with the FCC requirements as needed. > > 7. Please provide declaration of Bluetooth CORE V1.2 compliance as mentioned in the exhibits, or separate compliance with the following FCC requirements: > -Is the hopping sequence pseudorandom, based on the technical description? > -Is each channel used equally on average, based on the technical description? > -Does the associated system receiver have a compliant input bandwidth, based on the measured 20 dB emission bandwidth? > -Does the associated system receiver have the ability to hop in synchronization with the transmitter, based on the technical description? > -15.247(g) Does the design of the frequency hopping system allow it to comply with all pertinent requirements when presented with a lengthy data stream? > -15.247(h) Does the frequency hopping system comply with the non-coordination requirement? > > The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in 3 application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender. > > Best regards, > > Chris Harvey > [email protected] >

TOPCON CORPORATION Modular Approval Request Letter TOPCON CORPORATION’s BT/SD Board with FCC ID: H5P-FC200BTSD, would like to have your authorization as a modular approval specific to PDA. The requirements of Public Notice DA00-1407 have been met and shown on the following statements. 1. “Have its own RF shielding” Device is equipped with Metal shielding to cover RF section. Please refer the external photos. 2. “Have buffered modulation/data inputs (if such inputs are provided)”. All inputs to the modules are buffered through logic or microprocessor inputs. 3. “The modular transmitter must have its own power supply regulation.” The on-board regulator supplies 1.8V DC to Bluetooth chip except for the flash memory interface controller and the external input and output interface controller. Please refer the block diagram. 4. “The modular transmitter must comply with the antenna requirements of section 15.203 and 15.204(C).” The EUT meets the FCC antenna requirements. The spurious emission and soldered antenna structure meet the requirements. 5. “The modular transmitter must be tested in a stand-alone configuration” The EUT, BT/SD Board, is tested in full system configuration. Please see section Photographs of Test Configuration in the test report. 6. “The modular transmitter must be labeled with its own FCC ID number.” Yes. Please see the exhibition, Label Sample, In addition, this device is installed only by manufacturer(s). 7. “The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements.” The EUT is compliant with all applicable FCC rules. The instructions for maintaining compliance are given in the Users Manual. 8. “The modular transmitter must comply with any applicable RF exposure requirements.” The EUT is not applicable for RF exposure requirements because the output power is low. Signature: Applicant Name: Hiroto Shibuya Title: Engineer Section & Company: 75-1, Hasunuma-cho, Itabashi-Ku, Tokyo 174-8580 Japan TOPCON CORPORATION

TOPCON CORPORATION Declaration of Bluetooth CORE V1.2 Compliance It is hereby declared that the BT/SD Board with the FDD ID: H5P-FC200BTSD conforms to the Bluetooth CORE V1.2 specification by use of the Bluetooth components defined as following; Product Name: - Complete Class2 Bluetooth Module Product ID: - EYMF2CA**-** Company: - Taiyo Yuden Co., Ltd Listing Date and number of Bluetooth Qualification Web site: (http://qualweb.bluetooth.org/) - March 03, 2004 - B01446 Signature: Applicant Name: Hiroto Shibuya Title: Engineer Section & Company: 75-1, Hasunuma-cho, Itabashi-Ku, Tokyo 174-8580 Japan TOPCON CORPORATION

TOPCON CORPORATION Declaration It is hereby declared that the BT/SD Board with the FDD ID: H5P-FC200BTSD use only DH1 packet and prevent the use of any other packet type as following; (1) The BT/SD Board is designed for TOPCON’s Field Controllers that is a Microsoft Windows CE. Based PDA. (2) It is true that the Bluetooth Module installed in the BT/SD Board could support DH3 and DH5 packet if the corresponding command was sent from host devices. However the BT/SD Board is designed for TOPCON internal use. Its structure is specific to TOPCON’s Field Controllers whose Bluetooth application program only supports DH1. In addition, there doesn’t exist any setup function to change packet type of Bluetooth Module from DH1 in TOPCON’s Field Controllers. (3) If the third parties should try to make their own application program for TOPCON’s Field Controllers in order to use DH3 and/or DH5 packet, they couldn’t because the technical information is kept secret internally in TOPCON. (4) Thus the BT/SD Board can be used only DHI packet.. Signature: Applicant Name: Hiroto Shibuya Title: Engineer Section & Company: 75-1, Hasunuma-cho, Itabashi-Ku, Tokyo 174-8580 Japan TOPCON CORPORATION

TOPCON CORPORATION Product Overview The BT/SD Board is designed to provide wireless communication ability for the TOPCON’s “FC” Field Controller families to communicate with other Bluetooth devices via the class 2 of the Bluetooth V1.2 protocol. It is can be easily attached to “FC” Field Controller and easy to operate through the User Interface of “FC” Features Wireless Features Compact wireless data communication module designed for Makitra’s battery-operated tools Low power CSR BlueCore2-Ext Chipset (Bluetooth V1.2) Tx output: 0.5mW Tx and Rx Operation Frequency: 2402-2480 MHz Modulation Method: Frequency Hopping Spectrum Spread (FHSS) / GFSK Number of Channels: 79 (Normal Mode), 79 - 20 (Adaptive Hopping Mode) Channel Intervals / bit rate: 1 MHz / 1 Mbps Packet type in use: DH1 Dwell time: Less than 0.18 sec. Physical Attributes Size: 48mm (L) x 76mm (W) x 5.5mm (D) Weight: 0.03 Kg Operating Temperature: -20 deg. C to +50 deg. C Power Requirements: 0.3 W @ +3.3 VDC from “FC” Field Controller BT/SD Board

JAPAN QUALITY ASSURANCE ORGANIZATION 21-25, KINUTA 1-CHOME, SETAGAYA-KU, TOKYO 157-8573 JAPAN PHONE +81-3-3416-0111, FAX +81-3-3416-9691 JQA File No. : 400-60185 Issue Date : September 1, 2006 Page 1 of 65 EMI TEST REPORT JQA File No. : 400-60185 Model No. : BT/SD Board Type of Equipment : BT/SD Board Regulations Applied : CFR 47 FCC Rules and Regulations Part 15 : Industry Canada RSS-210(Issue 6) and RSS-Gen(Issue 1) FCC ID : H5P-FC200BTSD IC : 6050AFC200BT Applicant : TOPCON CORPORATION Address : 75-1, Hasunuma-cho, Itabashi-ku, Tokyo, 174-8580 Japan Manufacturer : Nagano Japan Radio Co., Ltd. Address : 1163, Inesato-Cho, Nagano-Shi, Nagano, 381-2288 Japan Received date of EUT : June 12, 2006 Test Result : Passed Test results in this report are obtained in use of equipment that is traceable to National Institute of Advanced Industrial Science and Technology (AIST) of Japan and National Institute of Information and Communications Technology (NICT) of Japan. The test results only respond to the tested sample. This report should not be reproduced except in full, without the written approval of JQA EMC Engineering Dept. Testing Div. COPY JQA File No. :400-60185 FCC ID:H5P-FC200BTSD IC:6050AFC200BT Model No. :BT/SD Board Issue Date :September 1, 2006 Standard :CFR 47 FCC Rules Part 15 Page 2 of 65 IC RSS-210 and RSS-Gen TABLE OF CONTENTS Page 1 Documentation 1.1 Test Regulation 4 1.2 General Information 4 - 5 1.3 Test Condition 6 – 12 1.4 EUT Modifications / Deviation from Standard 13 1.5 Test results 14 - 15 1.6 Summary 16 1.7 Test Configuration / Operation of EUT 17 1.8 EUT Arrangement (Drawing) 18 1.9 Preliminary Test and Test-setup (Drawings) 19 – 27 1.10 EUT Arrangement (Photographs) 28 – 32 COPY JQA File No. :400-60185 FCC ID:H5P-FC200BTSD IC:6050AFC200BT Model No. :BT/SD Board Issue Date :September 1, 2006 Standard :CFR 47 FCC Rules Part 15 Page 3 of 65 IC RSS-210 and RSS-Gen 2 Test Data 2.1 Channel Separation 33 2.2 Minimum Hopping Channel 34 – 35 2.3 Occupied Bandwidth 36 - 38 2.4 Dwell Time 39 2.5 Peak Output Power (Conduction) 40 2.6 Peak Output Power (Radiation) N/A 2.7 Peak Power Density (Conduction) 41 - 43 2.8 Peak Power Density (Radiation) N/A 2.9 Spurious Emissions (Conduction) 44 - 48 2.10 Spurious Emissions (Radiation) 49 - 56 2.11 AC Power Line Conducted Emissions 57 2.12 RF Exposure Compliance N/A 2.13 Spurious Emissions for Receiver (Radiation) 58 - 60 2.14 AC Power Line Conducted Emissions for Receiver 61 3 Appendix Test instruments List 62 – 65 COPY JQA File No. :400-60185 FCC ID:H5P-FC200BTSD IC:6050AFC200BT Model No. :BT/SD Board Issue Date :September 1, 2006 Standard :CFR 47 FCC Rules Part 15 Page 4 of 65 IC RSS-210 and RSS-Gen 1. DOCUMENTATION 1.1 TEST REGULATION FCC Rules and Regulations Part 15 Subpart B and C Radiated Spurious Emissions, Industry Canada IC RSS-210 (Issue 6) and RSS-Gen (Issue 1) Test procedure : The tests were performed with reference to the FCC Public Notice DA 00-705, released March 30, 2000. The test set-up was made in accordance to the general provisions of ANSIC63.4-2003. 1.2 GENERAL INFORMATION 1.2.1 Test facility : JQA Safety & EMC Center EMC Engineering Department is recognized under ISO/IEC 17025 by NVLAP and VLAC. 1) Test Facility located at EMC Engineering Dept. Testing Div. : - No.2 and 3 Anechoic Chambers(3 meters Site). - Shielded Enclosure. Open Area Test Site Industry Canada No.: 2079-7 2) EMC Engineering Dept. Testing Div. is recognized under the National Voluntary Laboratory accreditation Program for satisfactory compliance established in title 15, Part 285 Code of Federal Regulations. NVLAP Lab Code : 200189-0 (Effective through : June 30, 2007) COPY JQA File No. :400-60185 FCC ID:H5P-FC200BTSD IC:6050AFC200BT Model No. :BT/SD Board Issue Date :September 1, 2006 Standard :CFR 47 FCC Rules Part 15 Page 5 of 65 IC RSS-210 and RSS-Gen 1.2.2 Description of the Equipment Under Test (EUT) : 1) Type of Equipment : BT/SD Board 2) Product Type : Pre-production 3) Category : Spread Spectrum Transmitter(FHSS) 4) EUT Authorization : Certification 5) FCC ID : H5P-FC200BTSD IC : 6050AFC200BT 6) Trade Name : TOPCON 7) Model No. : BT/SD Board 8) Operating Frequency Range : 2402 MHz - 2480 MHz 9) Highest Frequency Used in the EUT : 2480 MHz 10) RF Output Power : -3.04dBm(measured value) 11) Serial No. : None 12) Date of Manufacture : None 13) Power Rating : 3.3VDC 14) EUT Grounding : None 15) Antenna Type : Integral Internal antenna (not accessible to the user) 16) Antenna Gain : +2.04 dBi 1.2.3 Definitions for symbols used in this test report : x - indicates that the listed condition, standard or equipment is applicable for this report. - indicates that the listed condition, standard or equipment is not applicable for this report. COPY JQA File No. :400-60185 FCC ID:H5P-FC200BTSD IC:6050AFC200BT Model No. :BT/SD Board Issue Date :September 1, 2006 Standard :CFR 47 FCC Rules Part 15 Page 6 of 65 IC RSS-210 and RSS-Gen 1.3 TEST CONDITION 1.3.1 The measurement of Channel Separation x - was performed. - was not applicable. Used test instruments : Type Number of test instruments (Refer to Appendix) Test Receiver 13 Spectrum Analyzer N/A Cable 48 Attenuator 80 Antenna N/A DC Power Supply 77 1.3.2 The measurement of Minimum Hopping Channel x - was performed. - was not applicable. Used test instruments : Type Number of test instruments (Refer to Appendix) Test Receiver 13 Spectrum Analyzer N/A Cable 48 Attenuator 80 Antenna N/A DC Power Supply 77 1.3.3 The measurement of Occupied Bandwidth x - was performed. - was not applicable. Used test instruments : Type Number of test instruments (Refer to Appendix) Test Receiver 13 Spectrum Analyzer N/A Cable 48 Attenuator 80 Antenna N/A DC Power Supply 77 COPY JQA File No. :400-60185 FCC ID:H5P-FC200BTSD IC:6050AFC200BT Model No. :BT/SD Board Issue Date :September 1, 2006 Standard :CFR 47 FCC Rules Part 15 Page 7 of 65 IC RSS-210 and RSS-Gen 1.3.4 The measurement of Dwell Time x - was performed. - was not ap…

Text truncated - open the document above for the full version.

COPY JQA File No. :400-60185 FCC ID:H5P-FC200BTSD IC:6050AFC200BT Model No. :BT/SD Board Issue Date :August 11, 2006 Standard :CFR 47 FCC Rules Part 15 Page 28 of 62 IC RSS-210 and RSS-Gen 1.10 TEST ARRANGEMENT (PHOTOGRAPHS) PHOTOGRAPHS OF THE CONDUCTED TEST COPY COPY JQA File No. :400-60185 FCC ID:H5P-FC200BTSD IC:6050AFC200BT Model No. :BT/SD Board Issue Date :August 11, 2006 Standard :CFR 47 FCC Rules Part 15 Page 29 of 62 IC RSS-210 and RSS-Gen PHOTOGRAPHS OF EUT CONFIGURATION FOR RADIATED EMISSIONS MEASUREMENT Photograph present configuration with maximum emission - Front view (X axis) - - Rear view (X axis) - COPY COPY JQA File No. :400-60185 FCC ID:H5P-FC200BTSD IC:6050AFC200BT Model No. :BT/SD Board Issue Date :August 11, 2006 Standard :CFR 47 FCC Rules Part 15 Page 30 of 62 IC RSS-210 and RSS-Gen PHOTOGRAPHS OF EUT CONFIGURATION FOR RADIATED EMISSIONS MEASUREMENT Photograph present configuration with maximum emission - Front view (Y axis) - - Rear view (Y axis) - COPY COPY JQA File No. :400-60185 FCC ID:H5P-FC200BTSD IC:6050AFC200BT Model No. :BT/SD Board Issue Date :August 11, 2006 Standard :CFR 47 FCC Rules Part 15 Page 31 of 62 IC RSS-210 and RSS-Gen PHOTOGRAPHS OF EUT CONFIGURATION FOR RADIATED EMISSIONS MEASUREMENT Photograph present configuration with maximum emission - Front view (Z axis) - - Rear view (Z axis) - COPY