H9PDM4046VoIP Phone using 802.11b

WIRELESS VOICE-OVER-IP NETWORK APPLIANCE NetVision ® Phone IEEE 802.11b, Direct Sequence The NetVision ® Phone from Symbol Technologies adds voice- over-IP (VoIP) communications to Symbol’s Wi-Fi ™ certified Spectrum24 ® 802.11b direct sequence wireless LAN installations, allowing simultaneous voice and data support on the same wireless backbone. Employing VoIP technology based on the ITU standard H.323, the NetVision Phone converts analog voice into compressed digital packets that are sent via TCP/IP protocol over standard data networks. The IEEE 802.11b-compliant NetVision Phone interoperates with many Wi-Fi certified wireless LANs. Broad support of VoIP solutions from major telephony vendors allows PBX integration of the NetVision Phone via a gateway for internal and external voice communication. Communication at the Speed of Business With business moving faster every day to keep pace with customers and competitors, communication is a tool of ever-increasing strategic importance. The ability to send voice and data over one wireless network can result in significant savings and allows for the development of new applications that increase productivity and provide better customer service. Advanced Handset and Secure, Quality of Service Wireless Communications The NetVision Phone handset features include:
Dialing: peer-to-peer, extension, name, speed
Messaging: SNPP-based two-way text messaging
Call hold, park/unpark, transfer, conference, forwarding, call waiting, mute, do not disturb
DHCP support
H.323 gatekeeper support
Vibrate, visual, ringer call alert
Headset support (2.5 mm)
Wireless firmware/configuration updates
Signal and battery strength indicators
Shared and personal user mode support
User configuration options (volume, LCD contrast and more; select features are not available with certain gateways) Embedded wireless communications features of the NetVision Phone include:
Dynamic Rate Scaling
Symbol Wireless Voice Prioritization, giving priority to NetVision Phone “voice packets” on the Symbol Spectrum24 wireless LAN
Pre-emptive Roaming for optimum voice quality and bandwidth maximization
40 and 128 bit WEP Encryption security; Kerberos V5
10 active calls per wireless access point, on average
IEEE 802.11d International Roaming PBX Connectivity Solutions The NetVision Phone is designed to work with your existing phone system via a gateway through a standard analog or digital connection. NetVision Phone PBX connectivity solutions include: AnalogEricsson Webcom Webswitch 2000/100 Digital (T1)Mitel Integrated Communications Platform (ICP) 3300 DigitalNortel Networks BCM, 802.11 wireless IP (Integrated)Gateway for Meridian; Cisco AVVID Skinny Client Control Protocol For North America, Latin America and Canada Symbol Technologies The Americas One Symbol Plaza Holtsville, NY 11742-1300 TEL: +1.800.722.6234/+1.631.738.2400 FAX: +1.631.738.5990 Symbol Website For a complete list of Symbol subsidiaries and business partners worldwide contact us at: www.symbol.com E-mail [email protected] Corporate Headquarters Symbol Technologies, Inc. One Symbol Plaza Holtsville, NY 11742-1300 TEL: +1.800.722-6234/+1.631.738.2400 FAX: +1.631.738.5990 For Asia Pacific Area Symbol Technologies Asia, Inc. (Singapore Branch) Asia Pacific Division 230 Victoria Street #05-07/09 Bugis Junction Office Tower Singapore 188024 TEL: +65.6796.9600 FAX: +65.6337.6488 For Europe, Middle East and Africa Symbol Technologies EMEA Division Symbol Place, Winnersh Triangle Berkshire, England RG41 5TP TEL: +44.118.9457000 FAX: +44.118.9457500 For system, product or services availability and specific information within your country, please contact your local Symbol Technologies office or Business Partner. Specifications are subject to change without notice. Symbol®, NetVision® and Spectrum24® are the registered trade- marks of Symbol Technologies, Inc. All other trademarks and service marks are proprietary to their respective owners. Part No. NVPDS Printed in USA 02/03 © Copyright 2003 Symbol Technologies, Inc. All rights reserved. Symbol is an ISO 9001 and ISO 9002 UKAS, RVC, and RAB Registered company, as scope definitions apply. NVPDS 02/03 The use of a gateway provides seamless access to desktop phones, zone-distant phone support, and PBX-provided supplementary services such as: Performance Characteristics Phone Protocol:ITU H.323 version 2 compliant; optional support for Cisco Skinny Client Control Protocol; optional enhanced H.323 implementation and support for Mitel’s MiNET protocoland Nortel Networks voice- over-IP solutions Codec:8-bit sampling; supporting G.711 and G.729a Voice Packet Size:40-160 bytes (configurable) Battery:7.2 volts rechargeable; Lithium ion; 800mAH Battery Life: Per charge: 3 hours talk time, 20 hour standby operation, battery meter Wireless Access Protocol:CSMA/CA Frequency Range:2.4 - 2.485 GHz Number of Channels:11 - 3 Data Rate:802.11b Direct Sequence Rate Scaling at 1, 2, 5.5, and 11 Mbps Wireless Output Power:60 mW Range:1,000+ ft./300+ m outdoors and up to 295 ft./75.5 m indoors Physical Characteristics Dimensions:5.10 in. H x 1.75 in. W x 0.75 in. D 13.0 cm H x 4.5 cm W x 1.9 cm D Weight: 5.5 oz./154 gm Display:LCD: 3 line, 12 character Buttons:0-9 *# key, Send, End, ‘, Function, Menu, Name, Recall, Store, Scroll, Hold Notification:Ringer/vibration/LED Ports:Headset port (2.5 mm) and external serial port Network Characteristics Protocol:TCP/IP; DHCP; IEEE 802.11b protocols Security:Wired Equivalent Privacy (WEP) 40 and 128 bit; Kerberos V5 User Environment Drop Specification:4 ft./1.2 m to concrete Temperature:32°F to 140°F/0°C to 60°C Accessories:AC adapter, dual battery charger, leather case, and bungee cord Regulatory Electrical Safety:Certified to UL1950, CSA C22.2 No. 950, EN60950/IEC950 EMI/RFI:FCC Part 15 Class B, ICES-003 Class B, European Union EMC Directive, Australian SMA, FCC Part 68 NetVision Phone Specification Highlights Mobilize Your Enterpr…

Text truncated - open the document above for the full version.

23456789111210 LED:Indicates an incoming call. EARPIECE MINI-HEADSET JACK:Plug headset into phone for hands- free use. LCD SCREEN:Shows the status of the phone and menu options. SELECTION KEYS:Use to select the option displayed on the LCD screen. END KEY:(Hard and Soft Key) Use to end a call, refuse a call, power off the phone and to return to the previous menu. FCT KEY:(Hard and Soft Key) Use to access PBX specific feature functionality. Note: The PBX specific features may be available only if they are support ed by the gateway and programmed by the administrator. HOLD KEY:Use to put a call on hold and switch to the other line. MOUTHPIECE : SERIAL PORT: Use to download software. SND KEY:Use to call the number dialed, accept a call, power on the phone and to select and save settings in the phone menus. SCROLL KEYS:Use to move up and down when selecting a feature, option or to increase or decrease call volume. Battery Operations Fully charge the battery for the NVP before initial use of the phone. Charge the battery attached or detached from the phone. Charging the Battery When charging the battery while attached to the phone, turn off the phone before inserting it into the charger. Place the battery or battery and phone combination into the charger. The LEDs on the charger indicate the following: GREENindicates a fully charged battery. REDindicates the battery is charging; wait until the LED changes to GREENbefore using battery. AMBERindicates the charger is waiting to charge the other battery. The charger charges the phone first. The charging cycle for the other device starts when the first cycle finishes. Removing the Battery Remove the battery by depressing the latch and pulling the top of the battery away from the phone. Note:When the battery latch is opened. You will find the part number, serial number and manufacturing and regulatory information located on the inside compartment. Replacing the Battery Replace the battery to the phone by aligning the feet on the battery with the notches on the phone. Push the top of the battery into the phone until the latch clicks. Basic Functions Basic Functions introduces the user to tasks, such as: • Power on • Login • Logout • LCD Icons • Make a call • Adjust call volume • Receive a call • End a call • Keyguard • Power off. Power On When powered on, the NVP will associate itself with the RF network and register with the telephony gateway. To power on the NVP, press SND. The screen briefly displays the NetVision splash screen containing the phone firmware version number. Login There are two different status displays, one for shared mode and the other for personal mode. Personal Mode: If your phone is configured in personal mode, the phone profile name displays with Func and Menu soft key options. If prompt- ed, enter your user PIN. When you are finished, press SND. Note:Obtain a user name and password (PIN) from the system administrator. Shared Mode: If your phone is configured in shared mode, a User Login screen displays. 1. Enter your extension number or select your name using the scroll keys. 2. Press SND. 3. If prompted, enter your user PIN. 4. When you are finished, press SND. Logout To logout of the network: 1. From Menu , select Logout . 2. Press SND. User Login displays on the LCD. LCD Icons Phone Lines - Indicates on which line a call is taking place. Number 1 for line 1 and number 2 for line 2. Signal Strength Indicator - Shows the RF signal strength from the access point. “X” - Indicates that the phone is not associated. Note: When the phone is not associated, it will beep three times and turn off after 5 minutes. Battery Strength - When battery is low, the battery indicator will begin to flash and the phone will beep once. Make a Call To place a call (to another NVP): 1. Enter extension number or select name of the NVP by using the scroll keys. 2. Press SND. The phone displays the name or number of the user being called. Adjust Call Volume When in an active call, adjust the volume of the current call using the scroll keys. Select from Level 0 (low) to Level 15 (high). Receive a Call For an incoming call, the caller ID feature allows user to identify callers before answering the call. There are two types of incoming call modes: no active call and call waiting. No Active Call To accept an incoming call when there is no active call taking place, press SND. Call Waiting To accept an incoming call while on an active call, press HOLD and the phone will switch to the second line to answer the call. End a Call To end a call, press END. The LCD screen displays Call Hangup . Keyguard Lock the keypad in order to prevent accidental phone operation and unnecessary battery power consumption. Any incoming call can be answered without unlocking the keypad. To lock keypad: 1. From Menu , scroll to Keyguard menu option. 2. Press SND. Keys Locked displays on the LCD screen. --or-- The NetVision Phone (NVP) provides on-site, wireless voice communication capability. The NVP performs like a cellular phone. Before use, the NVP requires configuration to the local network by the system administrator. 1 Soft Keys appear as text on the LCD screen : Use to return to the previous menu. :Use to ignore an incoming call. When used, it disables all ring tones temporarily. Note: The incoming call may still be answered by pressing SND. : Use to place a call. :Use to clear an entry. : Use to display the phone user menu. : Use to display name directory. :Use to accept an entry or answer a call. Battery Latch LEDs Battery 131415161718192021 Copyright© 2002 by Symbol Technologies, Inc. All rights reserved. Symbol, NetVision and Spectrum24 are registered trademarks of Symbol Technologies, Inc. Symbol Technologies, Inc. One Symbol Plaza Holtsville, NY 11742-1300 www.symbol.com 72-57312-01 Rev.A Select Menu and press *. Keys Locked displays on the LCD screen. To unlock the keypad: Press Unlk (Soft Key) and then *. Keys Unlocked displays on the LCD screen. Power Off Press and…

Text truncated - open the document above for the full version.

Hearing Aid CompatibilityThis product is marked HAC showing compliance with theapplicable requirements of FCC Part 68 and CS03-Part 5.Radio Frequency InterferenceRequirements for Home or Office UseThis device has been tested and found to comply with the limitsfor a Class B digital device pursuant to Part 15 of the FederalCommunications Commissions (FCC) Rules and Regulation.These limits are designed to provide reasonable protectionagainst harmful interference when the equipment is operated ina residential environment. This equipment generates, uses andcan radiate radio frequency energy and, if not installed andused in accordance with the instruction manual, may causeharmful interference to radio communications.However, there is no guarantee that interference will not occurin a particular installation. If the equipment does cause harmfulinterference to radio or television reception, which can bedetermined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more ofthe following measures: • Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that which the receiver is connected. Radio Frequency InterferenceRequirements-CanadaThis Class B digital apparatus meets the requirements of theCanadian Interference-Causing Equipment Regulations.Cet appareil numérique de la Classe B respecte toutes lesexigences du Reglement sur le Materiél Brouilleur du Canada.FCC RF Exposure Guidelines To comply with RF safety requirements use the specific belt clip. All other belt clips should be avoided and may not comply with RF safety requirements. The FCC has granted an Equipment Authorization for NetVision phones with all reported Specific Absorption Rate(SAR) levels evaluated as in compliance with the FCC RFemission guidelines. SAR information on NetVision phones is onfile with the FCC and can be found under the Display Grantsection of http://www .fcc.gove/oet/fccid. European Economic AreaThe European variant is intended for use throughout theEuropean Economic area, however authorization for userestricted as follows: • European standards dictate maximum radiated transmit power of 100 mW, EIRP and frequency range 2.400 -2.4835 GHz • France, the equipment is to be restricted to the 2.4465 - 2.4835 GHz frequency range • Belgium outside, the equipment is to be restricted to the 2.460 - 2.4835 GHz frequency range • Operation in Italy requires a user license. Hereby, Symbol Technologies, Inc., declares that thisproduct is in compliance with the essential requirementsand other relevant provisions of Directive 1999/5/EC.A Declaration of Conformity may be obtained fromhttp://www2.symbol.com/doc/. Laser Devices(Only applies to Data Phone-4046)Symbol products using lasers comply with US 21 CFR1040.10,Subchapter J and IEC825/EN 60 825 (or IEC825-1/EN60-825-1, depending on the date of manufacture). The laserclassification is marked on one of the labels on the product.Class 1 Laser devices are not considered to be hazardous whenused for their intended purpose. The following statement isrequired to comply with US and international regulations: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous visible or invisible laserlight exposure. Class 2 laser scanners use a low power, visible light diode.As with any very bright light source, such as the sun, the usershould avoid staring directly into the light beam. Momentaryexposure to a Class 2 laser is not known to be harmful. Samples of Laser Warning Labels CAUTION: LASER LIGHT WHEN OPEN. DO NOT STARE INTO BEAM.ATTENTION - LUMIERE LASER EN CAS D'OUVERTURE NE PAS REGARDER DANS LE FAISCEAU.VORSICHT - LASERLICHT, WENN ABDECKUNG GOFFNET. NICHT IN DEN STRAHL BLICKEN. LASER LIGHT - DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT LASERLICHT-NICHT IN DEN STRAHL BLICKEN LASER KLASSE 2 LUMIERE LASER - NE PAS REGARDER DANS LE FAISCEAU APPARIEL A LASER CLASS 2 630 - 680 nm. 1mw LASER LIGHT DO NOT STARE INTO BEAM 630 - 680nm LASER 1.0mW MAX OUTPUTCLASS II LASER PRODUCT Customer SupportSymbol Technologies provides its customers with prompt andaccurate customer support. Use the Symbol Support Center asthe primary contact for any technical problem, question orsupport issue involving Symbol products. If the SymbolCustomer Support specialists cannot solve a problem, accessto all technical disciplines within Symbol becomes availablefor further assistance and support. Symbol Customer Supportresponds to calls by email, telephone or fax within the timelimits set forth in individual contractual agreements. Whencontacting Symbol Customer Support, please provide thefollowing information: • serial number (MAC address) of unit• part number or product name. North American ContactsInside North America, contact Symbol at: Symbol Technologies, Inc.One Symbol PlazaHoltsville, New York 11742-1300Telephone: 1-631-738-2400 / 1-800-SCAN 234Fax: 1-631-738-5990 Symbol Support Center: Telephone: 1-800-653-5350Fax: (631) 563-5410Email: [email protected] International Contacts Outside North America, contact Symbol at:Symbol Technologies Technical Support12 Oaklands ParkBerkshire, RG41 2FD, United KingdomTel: 011-44-118-945-7000 or 1-631-738-2400 ext. 6213 Product Information and DocumentationDocumentation for NetVision Products is available online athttp://www .symbol.com/services/downloads/nvdoclist.html. NetVision Phone ® Regulatory Specifications Regulatory ComplianceSymbol RF products are designed to be compliant with the rulesand regulations in the locations into which they are sold andwill be labeled as required. The majority of Symbol RF devicesare type approved and do not require the user to obtain licenseor authorization before using the equipment. Any changes ormodifications to Symbol Technologies equipment not expresslyapproved by Symbol Technologies could void the user’sauthority…

Text truncated - open the document above for the full version.

The Enterprise Mobility Company Federal Communications Commission Authorization and Evaluation Division Confidentiality Request FCC ID: H9PDM4046 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, the Symbol Technologies Inc. hereby requests confidential treatment of information accompanying this Application as outlined below: Schematics Block Diagram Theory of Operation Build of Materials (BoM) The above documents contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to Symbol Technologies Inc. and provide unjustified benefits to its competitors. Symbol Technologies Inc. understands that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Respectfully, Mark S Luksich Director, Regulatory Engineering SYMBOL TECHNOLOGIES, INC. E-MAIL : [email protected] TEL: US 631 738 5134 FAX: US 631 738 3915 SYMBOL TECHNOLOGIES, INC. One Symbol Plaza, Holtsville, NY 11742-1300 • 516-738-2400 Website: http://www.symbol.com

Symbol Technologies, Inc. 11 May 2004 Subject: Request for an FCC Grant to be issued under FCC ID: H9PDM4046 To Whom It May Concern: This is a notification of intent to file for FCC approval for the model NP-4046 Spectrum 24® Direct Sequence NetVision Phone under FCC ID: H9PDM4046. The NP-4046’s are Voice over IP phones utilizing a 2.4 GHz direct sequence IEEE 802.11b compliant radio module (DM4046). The DM4046 radio module is the same radio in the previously certified model LA-4121 radio card FCC ID H9PLA4121. The tables below details the NP-4046 NetVision phone with a summary of the product’s specifications: Symbol Technologies – Model Number NP-4046 NetVision Phone FCC ID: H9PDM4046 Trade Name: Spectrum 24HR NP-4046 WLAN Communication device with two antennas for spatial diversity. Can be used on any 802.11 WLAN Notes: Additional devices will be added to this product family. Specification for all versions of the NP-4046 Intended Use The 11 Mbps WLAN communication devices are designed to be used in any retail, industrial or office environment. Frequency Band 2.400 - 2.4835 GHz Standards FCC 47 CFR Part 15, ETS 300 328 Modulation Direct Sequence Spread Spectrum Duplex Direction Simplex Transceiver Channel Spacing 11 MHz Emission 11M00F1D Transmitter Power 0 – 135 mW, programmable for different country regulations Type of antenna Two Dipole antennas for Spatial Diversity Please contact me either by email or phone should you have any questions. I look forward to hearing from you. Kind regards, Mark S. Luksich Director, Regulatory Engineering

Regultory Label FCC ID: H9PDM4046 Model Number: NP-4046-300 MANUFACTURED: XXXXXXXXX,XXXX N410 DE V gepruf te S ic herheit SEE REGULATORY ADDENDUM FOR PATENT INFORMATION. MADE IN XXXXXX NetVision® Symbol Technologies, Inc. Holtsville, N.Y. SN: XXXXXXXXXXX P /N : N P -4046-X X X -X X BAR CODE 0168 FREQ: MAX 2400-2483.5 MHz TYPE: DM4046 LISTED ACCESSORY I.T.E. THIS DEVICE CONTAINS AN APPROVED RLAN MODULE THIS CLASS B DIGITAL APPARATUS COMPLIES WITH CANADA ICES-003 . CET APPAREIL NUMÉRIQUE DE LA CLASSE B EST CONFORME À LA NORME NMB-003 DU CANADA. CONTAINS AN APPROVED RF DEVICE USING CERTIFICATION: CANADA: 1549104135A FCC ID: H9PDM4046 MAX 100mW JAPAN R 01NYDA0101/ 01GZDA0085 2.4DS4 TYPE: NP-4046-3 IF APPLICABLE AFFIX COUNTRY STAMP HERE H AC

REPORT ON Specific Absorption Rate Testing of the Symbol Technologies Inc. NetVision® Phone. Report Number: WS612323 – 001 issue 1.00April 2004 TUV Product Service Ltd. Segensworth Road, Titchfield Fareham, Hampshire, United Kingdom, PO15 5RH Tel: +44(0)1329 443300, Fax: +44(0)1329 443331 www.tuvps.co.uk Report Number WS612323 – 001 issue 1.00Page 1 of 51 REPORT ON:Specific Absorption Rate Testing of the Symbol Technologies Inc. NetVision® Phone. Report No: WS612323 – 001 issue 1.00 FCC ID:H9PDM4046 IC:1549104135A PREPARED FOR:Symbol Technologies Inc. One Symbol Plaza Holtsville NY 11742-1300 New York United States of America ATTESTATION:The wireless portable device described within this report has been shown to be capable of compliance for localised specific absorption rate (SAR) for General Population/Uncontrolled Exposure Limits as defined in the FCC standard Supplement C (Edition 01-01) to OET Bulletin 65 (Edition 97-01) and RSS-102 Issue 1 (Provisional) September 25, 1999 of 1.6 W/kg. The measurements shown in this report were made in accordance with the procedures specified in OET Bulletin 65 (Edition 97-01) and IEEE1528-2003. All reported testing was carried out on a sample of equipment to demonstrate compliance with the above standards. The sample tested was found to comply with the requirements in the applied rules. A Miller Senior SAR Test Engineer APPROVED BY: M J Hardy Deputy Wireless Group Leader DATED:20 th April 2004 DISTRIBUTION:Symbol Technologies Inc.Copy No: 1 BABT Copy No.: 2 Copy No.: Note: The test results reported herein relate only to the item tested as identified above and on the Status Page. FCC ID: H9PDM4046 IC: 1549104135A Report Number WS612323 – 001 issue 1.00Page 2 of 51 CONTENTS EXECUTIVE SUMMARY3 1.1Status4 1.2Declaration of Build Status5 1.3Summary6 1.4Test Result Summary7 TEST DETAILS9 2.1Test Equipment10 2.2Test Software10 2.3Dielectric Properties of Simulant Liquids11 2.4Test Conditions12 2.5Measurement Uncertainty13 2.6SAR Measuring System14 Probe and Amplifier Specification Probe Calibration SAR Measurement Procedure 2.7OET 65(c) and IEEE1528-2003 Test Positions32 SAM phantom head position Flat phantom position 2.8SAR Distributions (Area Scans – 2D)34 2.9Test Positional Photographs43 2.10Record Photographs45 2.11User Information50 2.12Copyright Statement51 FCC ID: H9PDM4046 IC: 1549104135A Report Number WS612323 – 001 issue 1.00Page 3 of 51 EXECUTIVE SUMMARY Specific Absorption Rate Testing of the Symbol Technologies Inc. NetVision® Phone. PROJECT MANAGER: M. GLASSPOOL FCC ID: H9PDM4046 IC: 1549104135A Report Number WS612323 – 001 issue 1.00Page 4 of 51 1.1STATUS MANUFACTURING DESCRIPTIONThe NetVision® Phone adds voice-over-IP (VoIP) communications to Symbol's Wi-Fi™ wireless LAN installations STATUS OF TESTSpecific Absorption Rate Testing APPLICANTSymbol Technologies Inc MANUFACTURERSymbol Technologies Inc TYPE NP4046 MODEL NUMBERNP4046–300 HARDWARE VERSIONBuild Status Rev A SERIAL NUMBERF410C83 RADIO LAN802.11b DSSS Radio Module. TYPEDM4046 POWER+20dBm (100mW) BATTERY MANUFACTURERWongs TYPE OR MODEL NUMBER50–24000–030 TEST SPECIFICATIONS: US Federal Government, Code of Federal Regulations, Title 47 Telecommunication, Chapter I Federal Communications Commission, part 2, section 1093. Federal Communications Commission (FCC) OET Bulletin 65c, Edition 01-01, Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields – Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions RSS-102 Issue 1 (Provisional) September 25, 1999: Evaluation Procedure for Mobile and Portable Radio Transmitters with respect to Health Canada’s Safety Code 6 for Exposure of Humans to radio Frequency Fields REFERENCES: IEEE 1528 –2003: Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Body Due to Wireless Communications Devices: Experimental Techniques BABT REGISTRATION NUMBER:WS612323. RECEIPT OF TEST SAMPLES:22 nd March 2004. START OF TEST:15 th April 2004. FINISH OF TEST:16 th April 2004. FCC ID: H9PDM4046 IC: 1549104135A Report Number WS612323 – 001 issue 1.00Page 5 of 51 1.2DECLARATION OF BUILD STATUS Signature Date 22 nd March 2004 D of B S Serial No OR612324 MAIN EUT MANUFACTURING DESCRIPTION NetVision Phone MANUFACTURER Symbol Technologies Inc TYPE NP4046-300 PART NUMBER NP4046-300-WW SERIAL NUMBER F410C83 HARDWARE VERSION Rev A COUNTRY OF ORIGIN United States of America FCC ID H9PDM4046 INDUSTRY CANADA ID 1549104135A TRANSMITTER OPERATING RANGE 2400 – 2483.5MHz TRANSMITTER POWER 100mW (+20dBm) RECEIVER OPERATING RANGE 2400 – 2483.5MHz INTERMEDIATE FREQUENCIES 374MHz EMISSION DESIGNATOR 11M0F1D DHSS/FHSS/COMBINED DSSS TECHNICAL DESCRIPTION The NetVision ® Phone incorporates an 802.11b Direct Sequence Spread Spectrum radio transmitter. The NetVision ® Phone adds voice-over-IP (VoIP) communications to Symbol's Wi-Fi ™ wireless LAN installations. BATTERY/POWER SUPPLY MANUFACTURING DESCRIPTION Lithium Ion Battery MANUFACTURER Symbol Technologies Inc. TYPE N/A PART NUMBER 50-24000-054 VOLTAGE 7.2V ACCESSORY MANUFACTURING DESCRIPTION NetVision Phone Leather Case MANUFACTURER Wongs TYPE N/A PART NUMBER N/A FCC ID: H9PDM4046 IC: 1549104135A Report Number WS612323 – 001 issue 1.00Page 6 of 51 1.3SUMMARY The NetVision® Phone incorporates an 802.11b Direct Sequence Spread Spectrum radio transmitter. The NetVision® Phone adds voice-over-IP (VoIP) communications to Symbol's Wi-Fi™ wireless LAN installations . The testing was performed with batteries supplied by Symbol and manufactured by Wongs. The battery was fully charged before each measurement and there were no external connections. SAR testing was performed with the device in a CW test mode only using a Specific Anthropomorphic Mannequin (SAM) phantom as specified in the standard IEEE 1528-2003. The phantom was filled with simulant liquid appropria…

Text truncated - open the document above for the full version.

lntertek Testing Services Symbol Technologies. FCC ID: H9PDM4046 Date of Test: October 29-3 1. 2000 Table of Contents 1.0Summary of Tests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..*............. 2 2.0General Description ............................................................................................................................. 3 2.1 Product Description ................................................................................................................. 3 . 2.2 Related Submittal(s) Grants 3 .............................. ................... .......... ............................... .... 2.3 Test Methodology .......... ............ 4 .............................. ..... .............................. ................ 2.4Test Facility .................................................................................................................... 4 ........ 3.0System Test Configuration 5 ................................................................................................................... 3. I Support Equipment and description i ... ......... .................... ....................... 3.2 Block Diagram of Test Setup 5 ............. ....................................................................... 3.3 Justification ...... ........6 ............................................................................ 3.4Software Exercisc Program ............................................................................... 6 3.5Mode of Operation During(1 Test ........................................................... 0 .......... 3 .6Modifications Required for Compliancc ......................... ........ 7 ................................. 3.7 Additions. deviations and exclusions from standards ................................ ................. 7 4.0 Measurement Results........................................................................................................................... 8 4.1Conducted Output Power at Antenna Tcrminals 8 ................................... .... ..... ............ 4.2 6 dB RF Bandwidth ........................................................................................................ 9 4.3Pow er Density Reading ................................................................... ...... .........................10 4.4 Out-of-Band Conducted Emissio…

Text truncated - open the document above for the full version.