H9PLA4137

Introduction The LA-4137 CFWL adapter allows CF Card slot equipped handheld computer systems to configure, connect to and establish a Spectrum24 network. Features Include: • 50-pin Type I adapter card fully compliant with PCMCIA electrical and mechanical specifications • Low-power operation for battery-powered devices with CF Card slots • Pocket PC and Windows CE driver support • Compact Flash form factor (CF+Type I extended) • Automatic data rate and channel selection of 1, 2, 5.5 and 11 Mbps • Wireless software upgrade • Wired Equivalent Privacy (WEP) encryption and decryption • An integrated antenna • Card and Socket Services support • Power management [Continuously Aware Mode (CAM) and Power Save Polling (PSP)]. Scope This Quick Reference Guide contains the CFWL adapter installation and configuration instructions for Windows CE/Pocket PC. Preparation Before beginning the installation, verify the hardware package contains: • LA-4137 CFWL adapter with an integrated antenna • Spectrum24 High Rate 11 Mbps Wireless LAN Software CDROM. Note: Verify the model indicated on the card and packaging before use. Contact the Symbol Support Center if an item is missing or not functioning. Supported Devices The LA-4137 CFWL adapter has been qualified by Symbol Technologies to support the following devices: • Palm/Handheld (PH) computers running Windows CE/Pocket PC • Palm OS (i.e. Hand ERA/TRG Pro). Installing the LA-4137 CFWL Adapter The LA-4137 CFWL adapter installation requires: • a handheld computer with a Type I CF Card slot • a desktop computer with a CDROM drive or Web access • a Spectrum24 High Rate 11 Mbps Wireless LAN Software CDROM. To install the CFWL adapter: 1. Insert the CFWL adapter into the CF Card slot. Arrows on the front of the CFWL adapter indicate the insertion point to the slot. 2. Slide in the CFWL adapter until it firmly seats. Caution! Align the CFWL adapter properly when inserting. Insert the CFWL adapter firmly without forcing. Forcing the CFWL adapter into the slot can damage the device or the adapter. Note: If the CFWL adapter does not fit into the CF Card slot, a 68-pin, male reciever PCMCIA adapter is needed. Additional Information Obtain additional information by contacting Symbol at: 1-800-722-6234, inside North America. +1-516-738-5200, in/outside North America http://www.symbol.com/ Copyright Copyright 2001 by Symbol Technologies, Inc. All rights reserved. No part of this publication may be modified or adapted in any way, for any purposes without permission in writing from Symbol Technologies, Inc. (Symbol). The material in this manual is subject to change without notice. Symbol reserves the right to make changes to any product to improve reliability, function, or design. No license is granted, either expressly or by implication, estoppel, or otherwise under any Symbol Technologies, Inc., intellectual property rights. An implied license only exists for equipment, ciecuits, and subsystems contained in Symbol products. Symbol, the Symbol logo and Spectrum24 are registerd trademarks of Symbol Technologies, Inc. Other product names mentioned in this manual may be trademarks or registered trademark of their respective companies and are hereby acknowledged. IBM is a registered trademark of International Business Machine Corporation. Microsoft, Windows, and Windows NT are registered trademarks of Microsoft Corporation. Novell and LAN Workplace are registered trademarks of Novell Inc. Patents This product is covered by one or more of the following U.S. and foreign Patents: U.S. Patent No. 4,387,297; 4,460,120; 4,496,831; 4,593,186; 4,603,262; 4,607,156; 4,652,750; 4,673,805; 4,736,095; 4,758,717; 4,816,660; 4,845,350; 4,896,026; 4,897,532; 4,923,281; 4,933,538; 4,992,717; 5,015,833; 5,017,765; 5,021,641; 5,029,183; 5,047,617; 5,103,461; 5,113,445; 5,130,520; 5,140,144; 5,142,550; 5,149,950; 5,157,687; 5,168,148; 5,168,149; 5,180,904; 5,216,232; 5,229,591; 5,230,088; 5,235,167; 5,243,655; 5,247,162; 5,250,791; 5,250,792; 5,260,553; 5,262,627; 5,262,628; 5,266,787; 5,278,398; 5,280,162; 5,280,163; 5,280,164; 5,280,498; 5,304,786; 5,304,788; 5,306,900; 5,321,246; 5,324,924; 5,337,361; 5,367,151; 5,373,148; 5,378,882; 5,396,053; 5,396,055; 5,399,846; 5,408,081; 5,410,139; 5,410,140; 5,412,198; 5,418,812; 5,420,411; 5,436,440; 5,444,231; 5,449,891; 5,449,893; 5,468,949; 5,471,042; 5,478,998; 5,479,000; 5,479,002; 5,479,441; 5,504,322; 5,519,577; 5,528,621; 5,532,469; 5,543,610; 5,545,889; 5,552,592; 5,557,093; 5,578,810; 5,581,070; 5,589,679; 5,589,680; 5,608,202; 5,612,531; 5,619,028; 5,627,359; 5,637,852; 5,664,229; 5,668,803; 5,675,139; 5,693,929; 5,698,835; 5,705,800; 5,714,746; 5,723,851; 5,734,152; 5,734,153; 5,742,043; 5,745,794; 5,754,587; 5,762,516; 5,763,863; 5,767,500; 5,789,728; 5,789,731; 5,808,287; 5,811,785; 5,811,787; 5,815,811; 5,821,519; 5,821,520; 5,823,812; 5,828,050; 5,850,078; 5,861,615; 5,874,720; 5,875,415; 5,900,617; 5,902,989; 5,907,146; 5,912,450; 5,914,478; 5,917,173; 5,920,059; 5,923,025; 5,929,420; 5,945,658; 5,945,659; 5,946,194; 5,959,285; 6,002,918; D305,885; D341,584; D344,501; D359,483; D362,453; D363,700; D363,918; D370,478; D383,124; D391,250; D405,077; D406,581; D414,171; D414,172; D419,548 Invention No. 55,358; 62,539; 69,060; 69,187 (Taiwan); No. 1,601,796; 1,907,875; 1,955,269 (Japan); European Patent 367,299; 414,281; 367,300; 367,298; UK 2,072,832; France 81/03938; Italy 1,138,713 Symbol Technologies, Inc. One Symbol Place Holtsville, NY 11742-1300 *73-20990-01A*1 72-52486-01 Revision A ORGI nser Anat PC2MbpsShort.cdr ® LA-4137 Compact Flash Wireless LAN Adapter Quick Reference Guide www.symbol.com Installing and Configuring the Driver in Windows CE Install the Spectrum24 Windows CE device driver from the Spectrum24 High Rate 11 Mbps Wireless LAN Software CDROM or download the driver from the Symbol Web site to a desktop computer. Symbol has bundled the NICTT and NCPA utilities with the Spectrum24 Windows CE driver. Use these utilitie…

Text truncated - open the document above for the full version.

Manufacturer’s Certification Declaration of Conformity Standard to which conformity is declared: FCC Part 15 Subpart B Class B Manufacturer/Importer’s Information Name: Symbol Technologies, Inc. Address: 7900 Glades Road Suite 600 Boca Raton, FL 33434 Telephone Number: 561-487-1718 Equipment Information Type of Equipment: 2.4 GHz Spread Spectrum Transceiver Trade Name: Spectrum 24
WLAN PC Card Model Number: CC-4137 Test Report Reference: 15.211127701.H9P I, the undersigned, herby declare that the equipment specified above conforms to Part 15 of the FCC Rules. (Signature) Mark S. Luksich, Sr. Mgr. Regulatory (Name & Title) 28 December 2001 (Date)

International Regulatory Compliance 7900 Glades Road Boca Raton, FL 33433 (561) 487 - 1718 Fax: (561) 483 – 3922 Date: 28 December 2001 Subject: Correction to the FCC ID To whom it may concern: During the filing of the submission for the H9PLA4137, a typographical error was made on the 731 form. The FCC ID on 731 with the confirmation number EA953106 was incorrectly listed as H9PH9PLA4137, please make the correction to H9PLA4137. Best regards, Mark S Luksich

Symbol Technologies, Inc. 1-Mar-02 Re: Permissive Change for FCC ID H9PLA4137 Subject: Response to Correspondence Reference Number: 22135 (731 Confirmation Number EA953106) A Class II permissive change was filed for a pending application. The change requested requires a new FCC identifier. If the two versions will both be marketed, they need separate FCC identifiers. Indicate whether both will be marketed or not. Review will continue once this is clarified. Joe, The Symbol radio LA-4137-1000-WW is a Compact Flash format of a 2.4 GHz DSSS radio. I included a set of photographs that shows that the LA-4137-1000-WW radio is mounted to a PCB to accommodate a PCMCIA format for the same radio. Sec. 2.1043 Changes in certificated equipment. (2) A Class II permissive change includes those modifications which degrade the performance characteristics as reported to the Commission at the time of the initial certification. Such degraded performance must still meet the minimum requirements of the applicable rules. When a Class II permissive change is made by the grantee, the grantee shall supply the Commission with complete information and the results of tests of the characteristics affected by such change. The modified equipment shall not be marketed under the existing grant of certification prior to acknowledgement by the Commission that the change is acceptable. There are no changes or modifications to the original radio. I have included an additional set of photographs to clarify my assertions. Regards, Mark SYMBOL TECHNOLOGIES LATIN AMERICA, INC. 7900 Glades Road, Suite 600, Boca Raton FL 33434 . (561) 487-1718 . Fax (561) 483-3922

Symbol Technologies, Inc. 14-Mar-02 Re: FCC ID H9PLA4137 Subject: Response to Correspondence Reference Number: 22275 (731 Confirmation Number EA953106) 1) Please supply new output power measurements with the device modulated. A spectrum analyzer was used with only a 1 Mhz RBW. The RBW must be greater than the 6 dB Bandwidth or use a peak power meter. 2) What are the following exhibits for? They should be removed. "Grant for intel cover letter" and" request to file" exhibits??? If Intel want their own grant, the have to file separately with their own FCC identifier. Suggest filing under 2.933 AFTER grant. 3) Justify modular approval and provide appropriate cover letter and labeling per the modular public notice. Joe, Item 1 The Steve Cheng at CCS Lab repeated the Transmitter Output Power Measurements with the Modulation ON using a Giga-tronics 8650A Peak Power Meter: Antenna one: 2412 GHz: 20.0 dBm 2437 GHz: 20.68 dBm 2462 GHz: 21.53 dBm Antenna two: 2412 GHz: 19.53 dBm 2437 GHz: 20.37 dBm 2462 GHz: 21.54 dBm Item 2 INTEL wants a Grant for the H9PLA4137 under there own Grantee code per 2.933, the FCC Website will not accept a Class II permissive change required while the original submission is in process. Previously I was directed to upload the files with the Symbol files and the INTEL Grant was issued at the same time as the Symbol grant. Item 3 The H9PLA4137 will be utilized primarily in Portable Applications. Based on your comments listed in the Correspondance 22275 the request for Modular approval is withdrawn. Regards, Mark S. Luksich SYMBOL TECHNOLOGIES LATIN AMERICA, INC. 7900 Glades Road, Suite 600, Boca Raton FL 33434 . (561) 487-1718 . Fax (561) 483-3922

Symbol Technologies, Inc. 29-Mar-02 Re: FCC ID H9PLA4137 Subject: Response to Correspondence Reference Number: 22425 (731 Confirmation Number EA953106) Joe, I have responded to all your questions by the ITEM numbers. a) Provide justification for modular approval. Address each requirement in the Public Notice that I e- mailed to you. Response ITEM a 1. The modular transmitter must have its own RF shielding. The LA-4137 uses a soldered on case to provide the necessary RF shielding. 2. The modular transmitter must have buffered modulation/data inputs. U301 provides buffered modulation/data inputs. 3. The modular transmitter must have its own power supply regulation B302 provides voltage regulation. 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna. The device uses a muRata GSC connector; additionally the antenna is mounted internally in the host and not end user accessible. 5. The modular transmitter must be tested in a stand-alone configuration. The module was tested in a stand-alone condition as seen in the Test Set up photographs. 6. The modular transmitter must be labeled with its own FCC ID number. The FCC ID was placed on the Regulatory label and can be seen on the external photographs. 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization The LA-4137 Integration guide is included for the manufacturers that provides instructions on necessary SAR and EMC compliance. 8. The modular transmitter must comply with any applicable RF exposure requirements. SYMBOL TECHNOLOGIES LATIN AMERICA, INC. 7900 Glades Road, Suite 600, Boca Raton FL 33434 . (561) 487-1718 . Fax (561) 483-3922 Symbol Technologies, Inc. The LA-4137 SAR Test Report documents compliance to the existing RF exposure limits for portable body-worn devices. The separation distance used during SAR testing was 2 cm or less, when the module is integrated into future host devices this device is mounted internally along with the antenna. 2. Please confirm that grant request is for: Card with one sleeved dipole for use in handheld terminals (portable conditions with respect to hand), no body-worn. Response ITEM 2 Card with one sleeved dipole for use in portable handheld terminals or body worn devices. The device passed the body worn RF exposure limits. Hand SAR limit is 4 W/kg in 10g. As stated before, we may not be able to make good use of this SAR data with respect to final host products. SAR data for future configurations will be submitted in Permissive Change filing. All manufacturers that are integrating this module are told they must have SAR measurements taken to ensure compliance. 3. Describe/demonstrate how antenna gain of 2 dBi is determined. Response ITEM 3 The antenna was mounted on a turntable in a semi-anechoic chamber. A cable was connected from a signal generator and power adjusted to 0 dBm at the input to the antenna cable. The maximum fundamental emission was measured following ANSI C63.4 and the gain calculated from the field strength and input power. The measured field strength was 97.2 dBuV/m. The calculations were derived from the following relationships. S=4*pi*r^2 S = surface area of a square, r = radius. P=p*S P = power, p = power density p=E^2/Z0, E field strength in V/m. Z0 120 * pi ohms (free space) for r = 3m EdB = PdBm + 95.2 + dBi dBi = EdB - PdBm - 95.2 dBi = 97.2 - 0 - 95.2 = 2.0 4. I did not find description of how device is used in 2 antenna mode. Will that be 2 sleeve dipoles side- by-side? Are both antennas on at same time? Response ITEM 4 Only one antenna is normally used to transmit, when two antennas are used they function in a receive diversity mode. One antenna is oriented along the devices y-axis and one antenna is oriented along the X-axis. SYMBOL TECHNOLOGIES LATIN AMERICA, INC. 7900 Glades Road, Suite 600, Boca Raton FL 33434 . (561) 487-1718 . Fax (561) 483-3922 Symbol Technologies, Inc. 5. Will there be intermediate cabling between card connectors and antenna(s) installed in host? Response ITEM 5 No, the antenna is connected directly to the card, no additional cables are used. 6. Will the sleeve antenna be internal to device housing, or protrude out of case away from hand in monopole-fashion? Response ITEM 6 The antennas are placed internally. 7. I didn't find any installation instructions for 1- or 2-antenna configurations. Please submit if applicable. Will instructions specify install at some minimum distance? Response ITEM 7 At this time, it is not applicable. 8. Form 731 states 0.142 W, EMC report states ~99mW, SAR reports states ~109mW. Please clarify what grant power is requested. Response ITEM 8 The nominal power output for this device is 100 mW; please use 99 mW on the grant. Draft grant comments, pending outcome of above RTs: Device with sleeve-dipole antenna as shown in this filing is approved for use in portable handheld terminals or body worn devices. Grantee must coordinate with OEM manufacturers to determine that RF exposure and emissions requirements have been satisfied for the final device configuration. OEM manufacturers must be informed of the compliance requirements for using this device with their products. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation and transmitter operating conditions for satisfying RF exposure compliance. Output power is conducted. EIRP is 99 m W in stand-alone configuration as describde in filing. Device is approved for portable hand-held terminal use or body worn devices with similar installation and oper…

Text truncated - open the document above for the full version.

Symbol Technologies, Inc. 29-Mar-02 Re: FCC ID H9PLA4137 Subject: Response to Correspondence Reference Number: 22425B (731 Confirmation Number EA953106) Joe, I have responded to all your questions by the ITEM numbers. For modular approvals, a second label is also required to be placed on the outside of the final device. Please submit this per the Public Notice. Use the same correspondence number with your reply. RESPONSE TO ITEM The radio was already integrated into one of the Symbol Terminals, it was approved as FCC ID: H9PLA4137SPS3046 on 03/08/2002. The label was included in that submission; this is the only terminal that Symbol has integrated todate. Tim: Please review the latest SAR replies from Mark. Let me know if there are any additional information. RESPONSE TO Verbal Message from Tim This radio was approved previously as the H9PLA4137SPS3046 on 03/08/2002. The radio was inside the case and placed in direct contact to the phantom. The Max. Peak SAR: 0.637 mW/g (1 g. avg) DSSS Body SAR; 0.315mW/g (10 g. avg) DSSS Hand SAR. Regards, Mark S. Luksich SYMBOL TECHNOLOGIES LATIN AMERICA, INC. 7900 Glades Road, Suite 600, Boca Raton FL 33434 . (561) 487-1718 . Fax (561) 483-3922

Symbol Technologies, Inc. 7900 Glades Road Boca Raton, FL 33433 (561) 487-1718 [email protected] 6 May 2002 Subject: Request for Confidentiality for files in the H9PLA4137 submission Rich Fabina: This is a request for confidentiality for the following files in the H9PLA4137 submission: Description of Exhibit LA4137 Block Diagram LA4137 Operational Description Please contact me either by email or phone should you have any questions. Regards, Mark S. Luksich Theory of Operartion( pcmcia not applied for) Schematic Diagram BOM Card

LA-4137 with Antenna Connector Front View © 2001 PCTEST Lab SYMBOL FCC ID: H9PLA4137 NVLAP Lab Code: 100431-0 DSSS Radio Card (PCMCIA)

LA-4137 Module Label FCC ID: H9PLA4137 CANADA :XXXXXXXXXX N410 FREQ: MAX 2400-2483.5 MHz TYPE: LA-4137 0168 MAX 100 mW P/N: LA-4137-1000-WW BAR CODE SYMBOL TECHNOLOGIES INC., HOLTSVILLE N.Y., 11742 MADE IN USA BP03 S/N AAOOAAOOEA AFFIX STAMP HERE R NYDA00XX/ GZDA00XX 2.4DS4 THIS DEVICE CONTAINS AN APPROVED RLAN MODULE Sample Exterior

Mobile & Wireless Systems Compact Flash Dipole Compact Flash Dipole (CF Dipole) The CF Dipole antenna is a 2-dBi sleeved- dipole that is omni-directional in azimuth plane. The CF Dipole uses a Murata GSC connector to comply with FCC 15.203 “unique coupling” requirement. In its use as a modular transceiver it could be as close as 2 cm of a persons body. CCS SAR report lists a worst- case SAR, averaged over 1g [mW/g] of 0.923 mW/gm at a separation of 20 mm. This transceiver is designed for use in devices in General Population/Uncontrolled Exposure categories. Location Body worn device Pattern Omni Type Dipole Max Gain 2 dBi Physical See attached dwg Cable Murata 92 Symbol P/N All antenna/terminal configurations used with the LA4137 will maintain a separation distance of 2 cm and a maximum gain of 2 dBi. Antenna Photo Rev 1

© 2001 PCTEST Lab SYMBOL FCC ID: H9PLA4137 NVLAP Lab Code: 100431-0 DSSS Radio Card (PCMCIA)

in accordance with the requirements of FCC Report and Order: ET Docket 93-62, and OET Bulletin 65 Supplement C for 802.11b 2.4GHz WIRELESS DSSS Tx/Rx MODULE MODEL: LA4137 FCC ID: H9PLA4137 January 24, 2002 REPORT NO: 01U1047-1 Prepared for SYMBOL TECHNOLOGIES, INC. 6480 VIA DEL ORO DRIVE SAN JOSE, CA 95119 - 1208 Prepared by COMPLIANCE CERTIFICATION SERVICES 561F MONTEREY ROAD, MORGAN HILL, CA 95037, USA TEL: (408) 463-0885 REPORT NO: 01U1047-1 DATE: DECEMBER 06, 2001 FCC ID: H9PLA4137 EUT: LA4137 COMPLIANCE CERTIFICATION SERVICES Page: 2 of 38 TEL:(408) 463-0885 561F MONTEREY ROAD, MORGAN HILL 95037 U.S.A. FAX:(408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Dates of Tests: December 05, 2001, January 22-23, 2002 Report No: 01U1047-1 Test Sample is a: Prototype Unit Tx Frequency: 2412 – 2462 MHz (CDMA) Max. RF Output Power: 19.74 dBm (Antenna Port #1) & 19.97 dBm (Antenna Port #2) based on Conducted Peak Output Power Measurements FCC Classification: Unlicensed Intentional Radiator RF Exposure environment: General Population/Uncontrolled Application Type: Certification FCC Rule Part(s): § 15.247 This wireless module has been tested according to the client’s specification as recorded in respective section in this report and had been tested in accordance with the measurement procedures specified in the FCC OET 65 Supplement C (released on 6/29/2001 see Test Report). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Steve Cheng EMC Engineering Manager APPLICANT: SYMBOL TECHNOLOGIES, INC. 6480 VIA DEL ORO DRIVE SAN JOSE, CA 95119 - 1208 TRADE NAME: SYMBOL TECHNOLOGIES, INC. MODEL: LA4137 SERIAL NUMBER: N/A FCC ID: H9PLA4137 CATEGORY: 2.4GHz DSSS WIRELESS Tx/Rx MODULE REPORT NO: 01U1047-1 DATE: DECEMBER 06, 2001 FCC ID: H9PLA4137 EUT: LA4137 COMPLIANCE CERTIFICATION SERVICES Page: 3 of 38 TEL:(408) 463-0885 561F MONTEREY ROAD, MORGAN HILL 95037 U.S.A. FAX:(408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. TABLE OF CONTENT 1. EUT DESCRIPTION.................................................................................................4 2. REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC.........5 3. DOSIMETRIC ASSESSMENT SETUP..................................................................6 3.1. MEASUREMENT SYSTEM DIAGRAM.............................................................................................................7 3.2. SYSTEM COMPONENTS..................................................................................................................................8 3.3. EUT ARRANGEMENT......................................................................................................................................12 4. EUT TUNE-UP PROCEDURE.............................................................................16 5. EVALUATION PROCEDURE..............................................................................17 5.1. SIMULATED TISSUE LIQUID PARAMETER CONFIRMATION....................................................................17 5.2. SYSTEM ACCURACY VERIFICATION...........................................................................................................17 5.3. SAR EVALUATION PROCEDURE..................................................................................................................20 5.4. EXPOSURE LIMIT............................................................................................................................................21 6. RESULTS............................................................................................................22 7. REFERENCES....................................................................................................33 8. APPENDIX..........................................................................................................34 8.1. EUT PHOTOS...................................................................................................................................................34 8.2 EQUIPMENTS LIST & CALIBRATION INFO..................................................................................................35 8.3 IEEE SCC-34/SC-2 P1528 RECOMMENDED TISSUE DIELECTRIC PARAMETERS...............................36 8.4 EQUIPMENTS CALIBRATION CERTIFICATE...............................................................................................37 REPORT NO: 01U1047-1 DATE: DECEMBER 06, 2001 FCC ID: H9PLA4137 EUT: LA4137 COMPLIANCE CERTIFICATION SERVICES Page: 4 of 38 TEL:(408) 463-0885 561F MONTEREY ROAD, MORGAN HILL 95037 U.S.A. FAX:(408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. 1. EUT DESCRIPTION Test Sample is a: Pre-Production Unit EUT Type: 2.4GHz DSSS Tx/Rx module Trade Name: Symbol Technologies, Inc. Model(s): LA4137 FCC IDENTIFIER: H9PLA4137 S/N: N/A (Pre-Production) Tx Frequency: 2412 – 2462 MHz (CDMA) Application Type: Certification FCC Classification: Unlicensed Intentional Radiator Modulation(s): CDMA FCC Rule Part(s): § 15.247 Max. RF Output Power: 19.74 dBm (Ant.Port #1) & 19.97 dBm (Ant. Port #2) based on Conducted Peak Power…

Text truncated - open the document above for the full version.

in accordance with the requirements of FCC Report and Order: ET Docket 93-62, and OET Bulletin 65 Supplement C for 802.11b 2.4GHz WIRELESS DSSS Tx/Rx MODULE MODEL: LA4137 FCC ID: H9PLA4137 January 31, 2002 REPORT NO: 01U1047-1 Prepared for SYMBOL TECHNOLOGIES, INC. 6480 VIA DEL ORO DRIVE SAN JOSE, CA 95119 - 1208 Prepared by COMPLIANCE CERTIFICATION SERVICES 561F MONTEREY ROAD, MORGAN HILL, CA 95037, USA TEL: (408) 463-0885 REPORT NO: 01U1047-1 DATE: JANUARY 31, 2002 FCC ID: H9PLA4137 EUT: LA4137 802.11b 2.4GHz WIRELESS DSSS Tx/Rx MODULE COMPLIANCE CERTIFICATION SERVICES Page: 2 of 46 TEL:(408) 463-0885 561F MONTEREY ROAD, MORGAN HILL 95037 U.S.A. FAX:(408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Dates of Tests: December 05, 2001, January 22,23&31, 2002 Report No: 01U1047-1 Test Sample is a: Pre-Production Unit Tx Frequency: 2412 – 2462 MHz Max. RF Output Power: 19.74 dBm (Antenna Port #1) & 20.39 dBm (Antenna Port #2) based on Conducted Output Power Measurements FCC Classification: Unlicensed Intentional Radiator RF Exposure environment: General Population/Uncontrolled Application Type: Certification FCC Rule Part(s): § 15.247 Separation Distance: 20 mm SAR Limits: 1.6mW/g Worse Body-Worn SAR: 1.16mW/g @low channel/5.5Mbps This wireless module has been tested according to the client’s specification as recorded in respective section in this report and in accordance with the measurement procedures specified in the FCC OET 65 Supplement C (released on 6/29/2001 see Test Report). The worst-case Body-Worn, with 20mm separation distance, SAR readings reported herein is 1.16mW/g at low channel(2412MHz) with data rate of 5.5Mbps. Additional test data / configuration are included to provide the reference information for the manufacturer as well for regulatory agencies. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Steve Cheng EMC Engineering Manager APPLICANT: SYMBOL TECHNOLOGIES, INC. 6480 VIA DEL ORO DRIVE SAN JOSE, CA 95119 - 1208 TRADE NAME: SYMBOL TECHNOLOGIES, INC. MODEL: LA4137 SERIAL NUMBER: N/A FCC ID: H9PLA4137 CATEGORY: 2.4GHz DSSS WIRELESS Tx/Rx MODULE REPORT NO: 01U1047-1 DATE: JANUARY 31, 2002 FCC ID: H9PLA4137 EUT: LA4137 802.11b 2.4GHz WIRELESS DSSS Tx/Rx MODULE COMPLIANCE CERTIFICATION SERVICES Page: 3 of 46 TEL:(408) 463-0885 561F MONTEREY ROAD, MORGAN HILL 95037 U.S.A. FAX:(408) 463-0888 This report shall not be reproduced except in full, without the written approval of CCS. This document may be altered or revised by Compliance Certification Services personnel only, and shall be noted in the revision section of the document. TABLE OF CONTENT 1. EUT DESCRIPTION.................................................................................................4 2. REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC.........5 3. DOSIMETRIC ASSESSMENT SETUP..................................................................6 3.1. MEASUREMENT SYSTEM DIAGRAM.............................................................................................................7 3.2. SYSTEM COMPONENTS..................................................................................................................................8 3.3. EUT ARRANGEMENT......................................................................................................................................12 4. EUT TUNE-UP PROCEDURE.............................................................................16 5. EVALUATION PROCEDURE..............................................................................17 5.1. SIMULATED TISSUE LIQUID PARAMETER CONFIRMATION....................................................................17 5.2. SYSTEM ACCURACY VERIFICATION...........................................................................................................17 5.3. SAR EVALUATION PROCEDURE.............................................................…

Text truncated - open the document above for the full version.