H9PPDT687CPortable Data Terminal w/WLAN PC Module

PDT 6800 Series Product Reference Guide PDT 6800 Series Product Reference Guide 70-32645-02 Revision A August 2001 ii  1998-2001 by Symbol Technologies, Inc. All rights reserved. No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Symbol. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this manual is subject to change without notice. The software is provided strictly on an “as is” basis. All software, including firmware, furnished to the user is on a licensed basis. Symbol grants to the user a non-transferable and non-exclusive license to use each software or firmware program delivered hereunder (licensed program). Except as noted below, such license may not be assigned, sublicensed, or otherwise transferred by the user without prior written consent of Symbol. No right to copy a licensed program in whole or in part is granted, except as permitted under copyright law. The user shall not modify, merge, or incorporate any form or portion of a licensed program with other program material, create a derivative work from a licensed program, or use a licensed program in a network without written permission from Symbol. The user agrees to maintain Symbol’s copyright notice on the licensed programs delivered hereunder, and to include the same on any authorized copies it makes, in whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered to the user or any portion thereof. Symbol reserves the right to make changes to any software or product to improve reliability, function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any Symbol Technologies, Inc., intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in Symbol products. Symbol, Spectrum One, and Spectrum24 are registered trademarks of Symbol Technologies, Inc. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Symbol Technologies, Inc. One Symbol Plaza Holtsville, New York 11742-1300 http://www.symbol.com iii Contents About This Guide Chapter Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Notational Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x Related Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . x Service Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xi Symbol Support Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xii Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiv Warranty Coverage and Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv Chapter 1. Getting Started Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Parts of the PDT 6800 Series Terminal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Battery Chargers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Printer Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Radio and Network Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Before You Use the Terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Install and Charge Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Load the Appropriate Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Chapter 2. Accessories Setup Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Required Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Parts of the CRD 38/6865 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Parts of the CRD 38/6866 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Wall Mounting the CRD 38/6865 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Wall Mounting the CRD 38/6866 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 iv PDT 6800 Series Product Reference Guide Ta…

Text truncated - open the document above for the full version.

68XX Series 68XX Series  1998-2002 SYMBOL TECHNOLOGIES, INC. All rights reserved. Symbol reserves the right to make changes to any product to improve reliability, function, or design. Symbol does not assume any product liability arising out of, or in connection with, the application or use of any product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any patent right or patent, covering or relating to any combination, system, apparatus, machine, material, method, or process in which Symbol products might be used. An implied license exists only for equipment, circuits, and subsystems contained in Symbol products. Symbol and the Symbol logo are registered trademarks of Symbol Technologies, Inc. Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. Symbol Technologies, Inc. One Symbol Plaza Holtsville, N.Y. 11742-1300 http://www.symbol.com Patents This product is covered by one or more of the following U.S. and foreign Patents: U.S. Patent No. 4,593,186; 4,603,262; 4,607,156; 4,652,750; 4,673,805; 4,736,095; 4,758,717; 4,760,248; 4,806,742; 4,816,660; 4,845,350; 4,896,026; 4,897,532; 4,923,281; 4,933,538; 4,992,717; 5,015,833; 5,017,765; 5,021,641; 5,029,183; 5,047,617; 5,103,461; 5,113,445; 5,130,520; 5,140,144; 5,142,550; 5,149,950; 5,157,687; 5,168,148; 5,168,149; 5,180,904; 5,216,232; 5,229,591; 5,230,088; 5,235,167; 5,243,655; 5,247,162; 5,250,791; 5,250,792; 5,260,553; 5,262,627; 5,262,628; 5,266,787; 5,278,398; 5,280,162; 5,280,163; 5,280,164; 5,280,498; 5,304,786; 5,304,788; 5,306,900; 5,324,924; 5,337,361; 5,367,151; 5,373,148; 5,378,882; 5,396,053; 5,396,055; 5,399,846; 5,408,081; 5,410,139; 5,410,140; 5,412,198; 5,418,812; 5,420,411; 5,436,440; 5,444,231; 5,449,891; 5,449,893; 5,468,949; 5,471,042; 5,478,998; 5,479,000; 5,479,002; 5,479,441; 5,504,322; 5,519,577; 5,528,621; 5,532,469; 5,543,610; 5,545,889; 5,552,592; 5,557,093; 5,578,810; 5,581,070; 5,589,679; 5,589,680; 5,608,202; 5,612,531; 5,619,028; 5,627,359; 5,637,852; 5,664,229; 5,668,803; 5,675,139; 5,693,929; 5,698,835; 5,705,800; 5,714,746; 5,723,851; 5,734,152; 5,734,153; 5,742,043; 5,745,794; 5,754,587; 5,762,516; 5,763,863; 5,767,500; 5,789,728; 5,789,731; 5,808,287; 5,811,785; 5,811,787; 5,815,811; 5,821,519; 5,821,520; 5,823,812; 5,828,050; 5,848,064; 5,850,078; 5,861,615; 5,874,720; 5,875,415; 5,900,617; 5,902,989; 5,907,146; 5,912,450; 5,914,478; 5,917,173; 5,920,059; 5,923,025; 5,929,420; 5,945,658; 5,945,659; 5,946,194; 5,959,285; 6,002,918; 6,021,947; 6,029,894; 6,031,830; 6,036,098; 6,047,892; 6,050,491; 6,053,413; 6,056,200; 6,065,678; 6,067,297; 6,082,621; 6,084,528; 6,088,482; 6,092,725; 6,101,483; 6,102,293; 6,104,620; 6,114,712; 6,115,678; 6,119,944; 6,123,265; 6,131,814; 6,138,180; 6,142,379; 6,172,478; 6,176,428; 6,178,426; 6,186,400; 6,188,681; 6,209,788; 6,209,789; 6,216,951; 6,220,514; 6,243,447; 6,244,513; 6,247,647; 6,308,061; 6,250,551; 6,295,031; 6,308,061; 6,308,892; 6,321,990; 6,328,213; 6,330,244; 6,336,587; 6,340,114; 6,340,115; 6,340,119; 6,348,773; 6,380,949; 6,394,355; D305,885; D341,584; D344,501; D359,483; D362,453; D363,700; D363,918; D370,478; D383,124; D391,250; D405,077; D406,581; D414,171; D414,172; D418,500; D419,548; D423,468; D424,035; D430,158; D430,159; D431,562; D436,104. Invention No. 55,358; 62,539; 69,060; 69,187, NI-068564 (Taiwan); No. 1,601,796; 1,907,875; 1,955,269 (Japan); European Patent 367,299; 414,281; 367,300; 367,298; UK 2,072,832; France 81/03938; Italy 1,138,713 rev. 06/02 1 Quick Reference Introduction The 68XX is a ruggedized, weather-resistant, hand-held portable computer combining the following capability in one package: • PC-standard architecture (8088 16-bit architecture) • DR-DOS compatibility • 16-line by 21-character display • Key input from a 35 or 46-key alphanumeric keyboard • Integrated scanning capability • Lithium Ion and NiCd rechargeable battery pack • Batch communications or RF network communications (with internally mounted antenna): -Spectrum One ® RF network (681X) -Spectrum24 ® RF network (684X). About This Guide This guide provides the operator with instructions for the following procedures: • Installing/removing the battery • Charging the battery • Powering the 68XX on and off • Adjusting the display contrast • Turning the backlight on/off • Using the keyboard • Using the integrated scanner • Running communications • Troubleshooting the 68XX. 2 68XX Series Parts of the 68XX + - = Status - Display Keyboard Scan LED Status LED Scan Window PWR Key Scan Trigger Battery Lock Handstrap Charging Contacts Optical Connectors Battery Compartment Battery Release Battery Pack 3 Quick Reference Required Accessories Required 68XX accessories include: • Lithium Ion or NiCd rechargeable battery pack or intrinsically safe NiCd rechargeable battery pack • CCM 38/6860 4-slot charging and communication module with spare battery charging slot or • CRD 38/6865 1-slot cradle charging and communications cradle or • CRD 38/6866 4-slot charging and communications cradle • RS-232 serial cable(s) • Power supply (1 per cradle). Optional Accessories Optional 68XX accessories include: • Wall mounting kit (p/n 3866-000) • UBC battery charger • PC adapter and printer interface module (PIM) • 10-hour trickle battery charger (wall cube) • Spectrum One and Spectrum24 network accessories •Holster. 4 68XX Series Providing Power Power for the 68XX is provided by a Lithium Ion or Nickel Cadmium (NiCd) rechargeable battery pack. Note:The Series 3800 NiCd battery packs, 3872-103, 3872- 105, and 3872-115, CANNOT be used in the 68XX. Installing New or Recharged Batteries To install the battery: 1. Orient the battery pack with the handle facing the 6800’s scan window. 2. Slide the pack into the battery compartment with the battery release buttons pressed in. 3. Press the battery lock in to secure. Changing…

Text truncated - open the document above for the full version.

PDT 687C Addendum Symbol Technologies, Inc. One Symbol Plaza, Holtsville, NY 11742-1300 http://www.symbol.com/manuals Introduction The PDT 687C terminal contains a CISCO radio card. Refer to the PDT 6800 Series Product reference Guide , p/n 70-32645-xx, for information on configuring the terminal. Regulatory Information FCC RF Exposure Guidelines The device complies with internationally recognised standards covering Specific Absorption Rate (SAR) related to human exposure to electromagnetic fields from radio devices. Handheld Devices To comply with FCC RF exposure requirements, this device must be operated in the hand. Radio Frequency Requirement This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received,including interference that may cause undesired operation. 72-62803-01 Revision A — April 2003

Cisco Systems, Inc. 320 Springside Drive Akron, Ohio 44333 Phone: 330 664-7900 Fax: 330-664-7922 http://www.cisco.com Phone: (330) 664-7362 Fax: (330) 664-7301 E-Mail: [email protected] April 8, 2003 BABT 34 Molesey Road Walton on Thames Surrey KT12 4RQ Re: Symbol PDT687C and VRC697C To Whom It May Concern: With this letter Cisco Systems, Inc. authorizes BABT to use available data from Cisco Systems’ AIR-LMC350 proprietary information on behalf of Symbol for their PDT687C and VRC697C. However, no proprietary information shall be released to Symbol for any purpose. Best Regards, Jim Nicholson EMC Compliance Engineer

Cisco Systems, Inc. 320 Springside Drive Akron, Ohio 44333 Phone: 330 664-7900 Fax: 330-664-7922 http://www.cisco.com Phone: (330) 664-7362 Fax: (330) 664-7301 E-Mail: [email protected] April 8, 2003 BABT 34 Molesey Road Walton on Thames Surrey KT12 4RQ Re: Symbol PDT687C and VRC697C To Whom It May Concern: The following information is to be held confidential pursuant to 47 CFR Part 0 §0.457 and Section 552(b)(4) of the Freedom of Information Act, because the information provided is proprietary and contains trade secrets. If made public, the information might be used to the disadvantage of the Cisco Systems, Inc. in the market place. In addition, this information is to be withheld from the applicant, Symbol Technologies, Inc., as well. Block Diagram Schematic Diagrams Technical Description Best Regards, Jim Nicholson EMC Compliance Engineer

Exhibit 3 External Photos Please see test report OR610828-2

NOTES: 1. SCRIPT FILE TO BE CREATED BY MANUFACTURING AND MUST MATCH THIS DOCUMENT EXACTLY. 2. LABEL STOCK P/N IS SUBJECT TO CHANGE. CHECK BOM FOR ACTUAL P ART NUMBER. 3. IN ALL CASES "X's......" REPRESENT VARIABLE FIELDS IN SCRIPT FILE. ACTUAL NUMBER OF CHARACTERS MAY V ARY. 4. IN THE CASE OF MULTIPLE APPROVALS THE ID NUMBER AND TYPE NUMBERS APPEAR IN SAME ORDER. 5. MODEL NUMBER MAY OR MAY NOT HAVE DASH NUMBER BEFORE COUNTRY CODE. SEE BOM FOR EXACT MODEL NAME. 6. MONTH AND YEAR REQUIRED. (IE: NOVEMBER, 2001) 7. COUNTRY OF ORIGIN REQUIRED. 8. CREATE VARIABLE FIELD FOR PLANT CODE PROD FAM: SLICK W/CISCO 352 RADIO DESCRIPTION: LBL:LCD, PDT687C - WW CTRY CODE: WW COUNTRY: SEE REGULATORY WEBSITE SN POOL: STANDARD LBL STOCK PN: 63-32274-03 *SEE NOTE 2 LBL SCRIPT : 6198801A *SEE NOTE XXXXXXXXXX SEE NOTE 7 AND 8 CLASS II LASER PRODUCT 630-680nm LASER 1.0 mW MAX OUTPUT STARE INTO BEAM.CLASS 2 LASER PRODUCT 630-680nM, 1 mW LASER APPAREIL A LASER DE CLASSE 2. CAUTION LASER LIGHT, DO NOT BLICKEN.LUMIÈRE LASER-NE PAS REGARDER DANS LE FAISCEAU ACHTUNG LASERSTRAHL, LASERCLASSE 2, NICHT IN DEN STRAHL LASER LIGHT-DO NOT STARE INTO BEAM CAUTION DE V geprufte Sicherheit LISTED ACCESSORY I.T .E. 9B97 N410 MADE IN SYMBOL TECHNOLOGIES,INC HOLTSVILLE N.Y. 11742 MODEL: PDT687C-XXXX-WW MFD: XXXXXXXXX,XXXX. S/N BARCODE (S)S/N: XXXXXXXXXXXXX 0650 69-61988-01A EDR 70305 SEE NOTE 5 SEE NOTE 6 THIS DEVICE CONTAINS AN APPROVED RF MODULE TYPE: LMC352 THIS DEVICE COMPLIES WITH CANADA RSS-210 FCC ID: H9PPDT687C CANADA:1549D-PDT687C .64 X .42 KEEP OUT AREA FOR STAMP APPLICATION. REDLINE DOES NOT PRINT IF APPLICABLE AFFIX COUNTRY STAMP HERE

X X X XX X X X X X C L A S S II L A S E R P R O DU C T 630-680nm L A S E R 1. 0 mW MA X O U T P U T STARE INTO BEAM.CLASS 2 LASER PRODUCT 630-680nM, 1 mW LASER A P P A R E IL A L A S E R DE C L A S S E 2. C A U T IO N L A S E R L IG H T , DO N O T B L IC K E N . L U MIÈ R E L A S E R -N E P A S R E G A R DE R DA N S L E F A IS C E A U A C H T U N G L A S E R S T R A H L , L A S E R C L A S S E 2, N IC H T IN DE N S T R A H L L A S E R L IG H T -DO N O T S T A R E IN T O B E A M C A U T IO N DE V gepruf te S ic herheit L IS T E D A C C E S S O R Y I. T. E . 9B 97 N410 MADE IN SYMBOL TECHNOLOGIES,INC HOLTSVILLE N.Y. 11742 MODEL: PDT687C-XXXX-WW MFD: XXXXXXXXX,XXXX. S /N B AR C O DE (S)S/N: XXXXXXXXXXXXX 0650 THIS DEVICE CONTAINS AN APPROVED RF MODULE TYPE: LMC352 THIS DEVICE COMPLIES WITH CANADA RSS-210 FCC ID: H9PPDT687C CANADA:1549D-PDT687C IF APPLICABLE AFFIX COUNTRY STAMP HERE LABEL POSITION PDT687C

Exhibit 9 Internal Photos Please see test report OR610828-2

TEST REPORT In support of the Application for Grant of Equipment Authorisation of the Symbol PDT687C Portable Data Terminal FCC ID: H9PPDT687CMay 2003 TUV Product Service Ltd. Segensworth Road, Titchfield Fareham, Hampshire, United Kingdom, PO15 5RH Tel: +44(0)1329 443300, Fax: +44(0)1329 443331 www.tuvps.co.uk Report Number WS610828Page 1 of 41 REPORT ON:Specific Absorption Rate testing of the Symbol PDT687C Portable Data Terminal. Report No: WS610828 FCC ID:H9PPDT687C PREPARED FOR:Symbol Technologies Inc One Symbol Plaza NY11742 United States ATTESTATION:The wireless portable device described within this report have been shown to be capable of compliance for localised specific absorption rate (SAR) for General Population/Uncontrolled Exposure Limits as defined in the European standard EN50361: 2002 of 2.0W/kg, FCC standard Supplement C (Edition 01-01) to OET Bulletin 65 (Edition 97-01) and RSS-102 Issue 1 (Provisional) September 25, 1999 of 1.6 W/kg. The devices were tested in accordance with the measurement procedures specified in European standard EN50361: 2002, Supplement C (Edition 01- 01) to OET Bulletin 65 (Edition 97-01), RSS-102 Issue 1 (Provisional) September 25 and IEEE1528-200x (Draft December 2002). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements. A. Miller Senior SAR Test Engineer APPROVED BY: M Jenkins Wireless Group Leader DATED:2 nd May 2003 DISTRIBUTION:Symbol Technologies IncCopy No: 1 Symbol Technologies Inc (CD ROM).Copy No(s): 2 BABT Copy No.: 3 Copy No.: 1 Note: The test results reported herein relate only to the item tested as identified above and on the Status Page. FCC ID: H9PPDT687C Report Number WS610828Page 2 of 41 CONTENTS EXECUTIVE SUMMARY3 1.1Status4 1.2Summary5 1.3Test Result Summary6 TEST DETAILS8 2.1Test Equipment9 2.2Test Software9 2.3Dielectric Properties of Simulant Liquids10 2.4Test Conditions11 2.5Measurement Uncertainty11 2.6SAR Measuring System12 Probe and Amplifier Specification Probe Calibration SAR Measurement Procedure 2.7OET65(c) Flat Phantom Test Position – Graphical Representation 30 2.8SAR Distributions (Area Scans – 2D)31 2.9Test Positional Photographs37 2.10Record Photographs41 For copyright details see page 41 of 41. FCC ID: H9PPDT687C Report Number WS610828Page 3 of 41 EXECUTIVE SUMMARY Specific Absorption Rate testing of the Symbol PDT687C Portable Data Terminal. PROJECT MANAGER: M. GLASSPOOL FCC ID: H9PPDT687C Report Number WS610828Page 4 of 41 1.1STATUS MANUFACTURING DESCRIPTIONPortable Data Terminal STATUS OF TESTSpecific Absorption Rate Testing APPLICANTSymbol Technologies Inc MANUFACTURERSymbol Technologies Inc TYPE OR MODEL NUMBERPDT687C HARDWARE VERSIONPDT687C-N2E643WW Rev 2 RADIO LAN2.4GHz Direct Spread Spectrum SERIAL NUMBERM1E72U84W BATTERY MANUFACTURERSymbol Technologies TYPE OR MODEL NUMBER21-54348-01 (Rev A) TEST SPECIFICATIONS: Federal Communications Commission, Code of Federal Regulations, Title 47 (CFR47), Vol. 1, Chapter 1, Part 2 (§2.1091 and §2.1093). Federal Communications Commission (FCC) OET Bulletin 65c, Edition 01-01, Evaluating Compliance with FCC Guidelines for Human Exposure to Radiofrequency Electromagnetic Fields – Additional Information for Evaluating Compliance of Mobile and Portable Devices with FCC Limits for Human Exposure to Radiofrequency Emissions CENELEC EN 50360: July 2001, Product Standard to demonstrate the compliance of mobile phones with the basic restrictions related to human exposure electromagnetic (300 MHz - 3 GHz). CENELEC EN 50361: July 2001, Basic standard for the measurement of Specific Absorption Rate related to human exposure to electromagnetic fields from mobile phones (300 MHz - 3 GHz). RSS-102 Issue 1 (Provisional) September 25, 1999: Evaluation Procedure for Mobile and Portable Radio Transmitters with respect to Health Canada’s Safety Code 6 for Exposure of Humans to radio Frequency Fields REFERENCES: IEEE 1528 –200X: DRAFT Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Body Due to Wireless Communications Devices: Experimental Techniques Council Recommendations 1999/519/EC on the limitations of exposure of the general public to electromagnetic fields (0 Hz - 3 GHz) annex II. BABT REGISTRATION NUMBER:WS610828. RECEIPT OF TEST SAMPLES:09 th April 2003. START OF TEST:09 th April 2003. FINISH OF TEST:08 th May 2003. FCC ID: H9PPDT687C Report Number WS610828Page 5 of 41 1.2SUMMARY The PDT687C is a Portable Data Terminal, which offers 2.4GHz Wireless LAN (11Mbps DSSS) connectivity. The terminal utilizes the Cisco Systems Inc 2.4GHz Wireless LAN Module, which is approved to FCC Part 15 Subpart C. The FCC ID of the module is LDK 102040. SAR testing was first performed using a Flat Phantom dimensions 220mmx200mmx150mm and with a sidewall thickness of 2.0mm. The phantom was filled to a depth of >150mm with 2450MHz Body simulant liquid. The dielectric properties were in accordance with the requirements for the dielectric properties specified in Supplement C (Edition 01-01) to OET Bulletin 65 (Edition 97-01). SAR testing was carried out at the top, middle and bottom frequency of each of the device- operating band. The device was placed against the side of the flat phantom and was in contact, to simulate the worst-case position. Note: for Body worn operation, the PDT687C is a Portable Data Terminal has been tested and meets the FCC RF exposure guidelines when used with an accessory which contains no metal and that positions these devices a minimum of 1.5cm from the body. Use of other accessories may not ensure compliance with FCC RF guidelines. Included in this report are descriptions of the test method; the equipment used and an analysis of the test uncertainties applicable and diagrams indicating the locations of maximum SAR for ea…

Text truncated - open the document above for the full version.

IMMERSIBLE SAR PROBE CALIBRATION REPORT Part Number: IXP – 050 S/N 0117 10 th October 2002 Indexsar Limited Oakfield House Cudworth Lane Newdigate Surrey RH5 5DR Tel: +44 (0) 1306 631 233 Fax: +44 (0) 1306 631 834 e-mail: [email protected] 2 INTRODUCTION This Report presents measured calibration data for a particular Indexsar SAR probe (S/N 0117) and describes the procedures used for characterisation and calibration. Indexsar probes are characterised using procedures that, where applicable, follow the recommendations of CENELEC [1] and IEEE [2] standards. The procedures incorporate techniques for probe linearisation, isotropy assessment and determination of liquid factors (conversion factors). Calibrations are determined by comparing probe readings with analytical computations in canonical test geometries (waveguides) using normalised power inputs. Each step of the calibration procedure and the equipment used is described in the sections below. CALIBRATION PROCEDURE 1. Equipment Used For the first part of the characterisation procedure, the probe is placed in an isotropy measurement jig as pictured in Figure 1. In this position the probe can be rotated about its axis by a non-metallic belt driven by a stepper motor. The probe is attached via its amplifier and an optical cable to a PC. A schematic representation of the test geometry is illustrated in Figure 2. A balanced dipole (900 MHz) is inserted horizontally into the bracket attached to a second belt (Figure 1). The dipole can also be rotated about its axis. A cable connects the dipole to a signal generator, via a directional coupler and power meter. The signal generator feeds an RF amplifier at constant power, the output of which is monitored using the power meter. The probe is positioned so that its sensors line up with the rotation center of the source dipole. By recording output voltage measurements of each channel as both the probe and the dipole are rotated, data are obtained from which the spherical isotropy of the probe can be optimised and its magnitude determined. The calibration process requires E-field measurements to be taken in air, in 900 MHz simulated brain liquid and at other frequencies/liquids as appropriate. 2. Linearising probe output The probe channel output signals are linearised in the manner set out in Refs [1] and [2]. The following equation is utilized for each channel: U lin = U o/p + U o/p 2 / DCP (1) where U lin is the linearised signal, U o/p is the raw output signal in voltage units and DCP is the diode compression potential in similar voltage units. DCP is determined from fitting equation (1) to measurements of U lin versus source feed power over the full dynamic range of the probe. The DCP is a characteristic of 3 the schottky diodes used as the sensors. For the IXP-050 probes with CW signals the DCP values are typically 0.10V (or 20 in the voltage units used by Indexsar software, which are V*200). 3. Selecting channel sensitivity factors to optimise isotropic response The basic measurements obtained using the calibration jig (Fig 1) represent the output from each diode sensor as a function of the presentation angle of the source (probe and dipole rotation angles). The directionality of the orthogonally-arranged sensors can be checked by analysing the data using dedicated Indexsar software, which displays the data in 3D format as in Figure 3. The left-hand side of this diagram shows the individual channel outputs after linearisation (see above). The program uses these data to balance the channel outputs and then applies an optimisation process, which makes fine adjustments to the channel factors for optimum isotropic response. The next stage of the process is to calibrate the Indexsar probe to a W&G EMR300 E- field meter in air. The principal reasons for this are to obtain conversion factors applicable should the probe be used in air and to provide an overall measure of the probe sensitivity. A multiplier is applied to factors to bring the magnitudes of the average E-field measurements as close as possible to those of the W&G probe. The following equation is used (where linearised output voltages are in units of V*200): E air 2 (V/m) = U linx * Air Factor x + U liny * Air Factor y + U linz * Air Factor z (2) It should be noted that the air factors are not separately used for normal SAR testing. The IXP-050 probes are optimised for use in tissue-simulating liquids and do not behave isotropically in air. 4. 900 MHz Liquid Calibration Conversion factors for use when the probes are immersed in tissue-simulant liquids at 900 MHz are determined either using a waveguide or by comparison to a reference probe that has been calibrated by NPL. Waveguide procedures are described later. The summary sheet indicates the method used for the probe S/N 0117. The conversion factor, referred to as the ‘liquid factor’ is also applied to the measurements of each channel. The following equation is used (where output voltages are in units of V*200): E liq 2 (V/m) = U linx * Air Factor x * Liq Factor x + U liny * Air Factor y * Liq Factor y + U linz * Air Factor z * Liq Factor z (3) A 3D representation of the spherical isotropy for probe S/N 0117 using these factors is shown in Figure 3. 4 The rotational isotropy can also determined from the calibration jig measurements and is reported as the 900MHz isotropy in the summary table. Note that waveguide measurements can also be used to determine rotational isotropy (Fig. 5). The design of the cells used for determining probe conversion factors are waveguide cells is shown in Figure 4. The cells consist of a coax to waveguide transition and an open-ended section of waveguide containing a dielectric separator. Each waveguide cell stands in the upright positition and is filled with liquid within 10 mm of the open end. The seperator provides a liquid seal and is designed for a good electrical transition from air filled guide to liquid filled guide. The choice of cell depends on …

Text truncated - open the document above for the full version.

FCC ID: LDK102040 MFA p0040008, d0050047 Date: May 31, 2000 Federal Communications Commission Via: Electronic Filing Attention: Authorization & Evaluation Division Applicant: Cisco Systems Inc Equipment: AIR-LMC350 FCC ID: LDK102040 FCC Rules: 15.247 and Confidentiality Gentlemen: On behalf of the Applicant, enclosed please find Application Form 731, Engineering Test Report and all pertinent documentation, the whole for approval of the referenced equipment as shown. Filing fees are attached. We trust the same is in order. Should you need any further information, kindly contact the writer who is authorized to act as agent. Sincerely yours, Morton Flom, P. Eng. enclosure(s) cc: Applicant MF/cvr FCC ID: LDK102040 MFA p0040008, d0050047 LIST OF EXHIBITS (FCCCERTIFICATION(TRANSMITTERS) - REVISED 9/28/98) APPLICANT: Cisco Systems Inc FCC ID: LDK102040 BY APPLICANT: 1. LETTER OF AUTHORIZATI…

Text truncated - open the document above for the full version.