HQXJRVCS1DCJRVCS1 Display Commander

JRVCS1 RV CONTROL AND MONITORING SYSTEM Installation and Operation Manual JRVCS1 ii CONTENTS CONTENTS ....................................................................................................................... .......... ii Introduction ................................................................................................................... ............... 4 Thank You! ..................................................................................................................... ....... 4 Features....................................................................................................................... ......... 4 Precautions .................................................................................................................... ....... 4 Packing List ................................................................................................................... ....... 4 Installation ................................................................................................................... ................. 5 Tools and Supplies............................................................................................................. ... 5 Disconnecting the Battery ..................................................................................................... 5 Selecting the Mounting Location........................................................................................... 5 Mounting the Digital Commander (DC)................................................................................. 5 Wiring ......................................................................................................................... .................. 6 Troubleshooting ................................................................................................................ ........... 7 Specifications ................................................................................................................. .............. 9 FCC Notes ...................................................................................................................... .... 10 JRVCS1 iii JRVCS1 4 INTRODUCTION Thank You! Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen JRVCS1 for maximum enjoyment. Features Features of Jensen JRVCS1 system include:  Control four zones of lighting.  Monitor all water tank levels.  Control and monitor the Water Heater.  Control and monitor the Generator. Precautions  Use the Proper Power Supply. This product is designed to operate with a 12 volt DC, negative ground battery system (the standard system in a North American vehicle).  Use Authorized Service Centers. Do not attempt to disassemble or adjust this precision product; contact a professional for assistance.  Avoid Moisture. To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.  Avoid Cleaning Products. The front of this unit should only be cleaned with a slightly damp cloth. Do not use cleansers.  Use Recommended Accessories. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES. Packing List 1 Cover, 2 Thumb Screws 1 Body Control Module (BCM) 1 Display Commander (DC) JRVCS1 5 INSTALLATION It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen JRVCS1 installed by a reputable RV dealership Tools and Supplies You will need these tools and supplies to install your JRVCS1:  Phillips screwdriver  Wire cutters and strippers  Electrical tape  Crimping tool  Volt meter/test light  Fork Crimp connectors  10 gauge wire for power and slide connections  14 and 18 gauge wire for all other connections  Four #8 PH (0.164” x 0.75”) screws for the DC  Six #8 PH (0.164” x 1.0”) screws for the BCM Disconnecting the Battery To prevent a short circuit, be sure to turn off 12V power and remove the negative (-) battery cable prior to installation. Selecting the Mounting Location Select a mounting location, taking care to avoid the following:  Places exposed to heat-radiating appliances such as electric heaters  Adjacent to other equipment that radiates heat  Poorly-ventilated or dusty places  Moist or humid locations Mounting the Display Commander (DC)  Use the mounting hole diagram to measure and cut a mounting hole  Route power wires through the hole and connect  Check and ensure correct operation  Mount the unit using four #8 PH (0.164” x 0.75”) screws  Attach Trim ring CUTOUT FOR DISPLAY COMMANDER (DC) NOTE: Before cutting the mounting hole, make sure the area behind the mounting location is clear of wires, fuel and vacuum or water lines. 格式化: 字型: 粗體 格式化: 左 0 字元 刪除 : 刪除 : 刪除 : . 刪除 : JRVCS1 6 WIRING The wiring diagram depicts all the wiring connections required for proper operation of the unit . BODY CONTROL MODULE (BCM) CONNECTIONS PIN NO. WIRE COLOR/SIZE DESCRIPTION 1 BLUE (18) FRESH TANK 1 (IN) 2 FRESH TANK 2 (IN) 3 BROWN (18) BLACK TANK 1 (IN) 4 LIGHT BLUE (18) BLACK TANK 2 (IN) 5 GRAY (18) GRAY TANK 1 (IN) 6 RED (18) GRAY TANK 2 (IN) 7 LIGHT BLUE (18) GRAY TANK 3 (IN) 8 WHITE (18) TANK SENSOR GROUND (IN) 9 GREEN (14) LIGHT GROUP 1 + (IN) 10 WHITE (14) LIGHT GROUP 1 - (IN/OUT) 11 GREEN (14) LIGHT GROUP 1 + (OUT) 12 GREEN (14) LIGHT GROUP 2 + (IN) 13 WHITE (14) LIGHT GROUP 2 - (IN/OUT) 14 GREEN (14) LIGHT GROUP 2 + (OUT) 15 GREEN (14) LIGHT GROUP 3 + (IN) 16 WHITE (14) LIGHT GROUP 3 – (IN/OUT) 17 GREEN (14) LIGHT GROUP 3 + (OUT) 18 GREEN (14) LIGHT GROUP 4 + (IN) 19 WHITE (14) LIGHT GROUP 4 - (IN/OUT) 20 GREEN (14) LIGHT GROUP 4 + (OUT) 21 ORANGE (14) EXTERIOR LIGHTS + (IN) 22 WHITE (14) EXTERIOR LIGHTS - (IN/OUT) 23 ORANGE (14) EXTERIOR LIGHTS + (OUT) 24 ORANGE (14) SECURITY LIGHTS + (IN) 25 W…

Text truncated - open the document above for the full version.

JRVCS1 RV CONTROL AND MONITORING SYSTEM Installation and Operation Manual JRVCS1 ii CONTENTS CONTENTS ....................................................................................................................... .......... ii Introduction ................................................................................................................... ............... 4 Thank You! ..................................................................................................................... ....... 4 Features....................................................................................................................... ......... 4 Precautions .................................................................................................................... ....... 4 Packing List ................................................................................................................... ....... 4 Installation ................................................................................................................... ................. 5 Tools and Supplies............................................................................................................. ... 5 Disconnecting the Battery ..................................................................................................... 5 Selecting the Mounting Location........................................................................................... 5 Mounting the Digital Commander (DC)................................................................................. 5 Wiring ......................................................................................................................... .................. 6 Troubleshooting ................................................................................................................ ........... 7 Specifications ................................................................................................................. .............. 9 FCC Notes ...................................................................................................................... .... 10 JRVCS1 iii JRVCS1 4 INTRODUCTION Thank You! Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen JRVCS1 for maximum enjoyment. Features Features of Jensen JRVCS1 system include:  Control four zones of lighting.  Monitor all water tank levels.  Control and monitor the Water Heater.  Control and monitor the Generator. Precautions  Use the Proper Power Supply. This product is designed to operate with a 12 volt DC, negative ground battery system (the standard system in a North American vehicle).  Use Authorized Service Centers. Do not attempt to disassemble or adjust this precision product; contact a professional for assistance.  Avoid Moisture. To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.  Avoid Cleaning Products. The front of this unit should only be cleaned with a slightly damp cloth. Do not use cleansers.  Use Recommended Accessories. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES. Packing List 1 Cover, 2 Thumb Screws 1 Body Control Module (BCM) 1 Display Commander (DC) JRVCS1 5 INSTALLATION It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen JRVCS1 installed by a reputable RV dealership Tools and Supplies You will need these tools and supplies to install your JRVCS1:  Phillips screwdriver  Wire cutters and strippers  Electrical tape  Crimping tool  Volt meter/test light  Fork Crimp connectors  10 gauge wire for power and slide connections  14 and 18 gauge wire for all other connections  Four #8 PH (0.164” x 0.75”) screws for the DC  Six #8 PH (0.164” x 1.0”) screws for the BCM Disconnecting the Battery To prevent a short circuit, be sure to turn off 12V power and remove the negative (-) battery cable prior to installation. Selecting the Mounting Location Select a mounting location, taking care to avoid the following:  Places exposed to heat-radiating appliances such as electric heaters  Adjacent to other equipment that radiates heat  Poorly-ventilated or dusty places  Moist or humid locations Mounting the Display Commander (DC)  Use the mounting hole diagram to measure and cut a mounting hole  Route power wires through the hole and connect  Check and ensure correct operation  Mount the unit using four #8 PH (0.164” x 0.75”) screws  Attach Trim ring CUTOUT FOR DISPLAY COMMANDER (DC) NOTE: Before cutting the mounting hole, make sure the area behind the mounting location is clear of wires, fuel and vacuum or water lines. 格式化: 字型: 粗體 格式化: 左 0 字元 刪除 : 刪除 : 刪除 : . 刪除 : JRVCS1 6 WIRING The wiring diagram depicts all the wiring connections required for proper operation of the unit . BODY CONTROL MODULE (BCM) CONNECTIONS PIN NO. WIRE COLOR/SIZE DESCRIPTION 1 BLUE (18) FRESH TANK 1 (IN) 2 FRESH TANK 2 (IN) 3 BROWN (18) BLACK TANK 1 (IN) 4 LIGHT BLUE (18) BLACK TANK 2 (IN) 5 GRAY (18) GRAY TANK 1 (IN) 6 RED (18) GRAY TANK 2 (IN) 7 LIGHT BLUE (18) GRAY TANK 3 (IN) 8 WHITE (18) TANK SENSOR GROUND (IN) 9 GREEN (14) LIGHT GROUP 1 + (IN) 10 WHITE (14) LIGHT GROUP 1 - (IN/OUT) 11 GREEN (14) LIGHT GROUP 1 + (OUT) 12 GREEN (14) LIGHT GROUP 2 + (IN) 13 WHITE (14) LIGHT GROUP 2 - (IN/OUT) 14 GREEN (14) LIGHT GROUP 2 + (OUT) 15 GREEN (14) LIGHT GROUP 3 + (IN) 16 WHITE (14) LIGHT GROUP 3 – (IN/OUT) 17 GREEN (14) LIGHT GROUP 3 + (OUT) 18 GREEN (14) LIGHT GROUP 4 + (IN) 19 WHITE (14) LIGHT GROUP 4 - (IN/OUT) 20 GREEN (14) LIGHT GROUP 4 + (OUT) 21 ORANGE (14) EXTERIOR LIGHTS + (IN) 22 WHITE (14) EXTERIOR LIGHTS - (IN/OUT) 23 ORANGE (14) EXTERIOR LIGHTS + (OUT) 24 ORANGE (14) SECURITY LIGHTS + (IN) 25 W…

Text truncated - open the document above for the full version.

ETC Report No. : 15-05-RBF-037-01 FCC ID.: HQXJRVCS1DC Sheet 1 of 8 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 1. 2. ETC Report No. : 15-05-RBF-037-01 FCC ID.: HQXJRVCS1DC Sheet 2 of 8 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 3. 4. ETC Report No. : 15-05-RBF-037-01 FCC ID.: HQXJRVCS1DC Sheet 3 of 8 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 5. 6.

ETC Report No. : 15-05-RBF-037-01 FCC ID.: HQXJRVCS1DC Sheet 4 of 8 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 7. ETC Report No. : 15-05-RBF-037-01 FCC ID.: HQXJRVCS1DC Sheet 5 of 8 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 8. 9. ETC Report No. : 15-05-RBF-037-01 FCC ID.: HQXJRVCS1DC Sheet 6 of 8 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 10. 11. ETC Report No. : 15-05-RBF-037-01 FCC ID.: HQXJRVCS1DC Sheet 7 of 8 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 12. 13. Antenna ETC Report No. : 15-05-RBF-037-01 FCC ID.: HQXJRVCS1DC Sheet 8 of 8 Sheets Rev. No 2.1 CONSTRUCTION PHOTOS OF EUT 14. Panel 15. Panel

Statement of Justification and Compliance for SAR Test Exclusion Product: JRVCS1 Display Commander FCC ID: HQXJRVCS1DC Manufacturer: SYSGRATION LTD.(Nan-Kang Factory) Brand: JENSEN Model: JRVCS1DC According to FCC KDB 447498 D01 General RF Exposure Guidance v05 4.3.1. Standalone SAR test exclusion considerations 1) The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f (GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, 16 where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion. For the present device, the declared output power is 4dBm Max.. So, max. power of channel, including tune-up tolerance = 2.512 mW (4dBm) min. test separation distance = 5 mm f(GHz) = 2.480 [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] = (2.512 / 5) · (√2.480) = 0.79 ≤ 3.0 Hence the SAR Exclusion Threshold condition is satisfied and the SAR evaluation for general population exposure conditions is not required.

Rev. No 1.0 FCC Part 15 EMI TEST REPORT Part I – Bluetooth (FHSS) of E.U.T. : JRVCS1 Display Commander Model : JRVCS1DC FCC ID : HQXJRVCS1DC for APPLICANT : SYSGRATION LTD. ADDRESS : 6F-2.,No.1,Sec.1,Tiding Blvd., Neihu Dist., Taipei City 114, Taiwan Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO. 34. LIN 5, DINGFU VIL., LINKOU DIST., NEW TAIPEI CITY, TAIWAN, 24442, R.O.C. Tel:(02)26023052 Fax:(02)26010910 http://www.etc.org.tw ; e-mail : [email protected] Report Number : 15-05-RBF-037-01 ETC Report No. : 15-05-RBF-037-01 FCC ID: HQXJRVCS1DC Rev. No 1.0 TEST REPORT CERTIFICATION Applicant : SYSGRATION LTD. 6F-2.,No.1,Sec.1,Tiding Blvd., Neihu Dist., Taipei City 114, Taiwan Manufacture : SYSGRATION LTD.(Nan-Kang Factory) No.28,North Industry Rd., Nan-Kang Industrial Zone, Nan-Tou City, Nan-Tou County 540, Taiwan Description of Device : a) Type of EUT : JRVCS1 Display Commander b) Trade Name : JENSEN c) Model No. : JRVCS1DC d) Power Supply : DC 12V Regulation Applied : FCC Rules and Regulations Part 15 Subpart C I HEREBY CERTIFY THAT: The data shown in this report were made in accordance with the procedures given in ANSI C63.10-2009, and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note: 1. The result of the testing report relate only to the item tested. 2. The testing report shall not be reproduced expect in full, without the written approval of ETC. Summary of Tests Test Results Radiated Emission Pass Conducted Emission N/A Hopping Channel Separation Pass Number of Hopping frequencies used Pass Hopping Channel Bandwidth Pass Dwell Time of each frequency Pass Output Power Requirement Pass 100 kHz Bandwidth of Frequency Band Edges Requirement Pass Out-of-Band Conducted Emission Requirement Pass ETC Report No. : 15-05-RBF-037-01 FCC ID: HQXJRVCS1DC Rev. No 1.0 Date Test Item Received : May 28, 2015 Date Test Campaign Completed : Jun. 02, 2015 Date of Issue : Jun. 17, 2015 Test Engineer : ( Jiapeng Chen , Engineer ) Approve & Authorized : S. S. Liou, Section Manager EMC Dept. II of ELECTRONICS TESTING CENTER, TAIWAN ETC Report No. : 15-05-RBF-037-01 FCC ID: HQXJRVCS1DC Rev. No 1.0 Table of Contents Page 1 GENERAL INFORMATION ....................................................................................................... 1 1.1 Product Description...................................................................................................................... 1 1.2 Test Methodology ........................................................................................................................ 1 1.3 Test Facility.................................................................................................................................. 1 2 PROVISIONS APPLICABLE...................................................................................................... 2 2.1 Definition ..................................................................................................................................... 2 2.2 Requirement for Compliance ....................................................................................................... 3 2.3 Restricted Bands of Operation ..................................................................................................... 5 2.4 Labeling Requirement .................................................................................................................. 6 2.5 User Information .......................................................................................................................... 6 3 SYSTEM TEST CONFIGURATION .......................................................................................... 7 3.1 Justification .................................................................................................................................. 7 3.2 Devices for Tested System........................................................................................................... 7 4 RADIATED EMISSION MEASUREMENT .............................................................................. 8 4.1 Applicable Standard ..................................................................................................................... 8 4.2 Measurement Procedure............................................................................................................... 8 4.3 Measuring Instrument ................................................................................................................ 10 4.4 Radiated Emission Data ............................................................................................................. 11 4.5 Field Strength Calculation.......................................................................................................... 21 4.6 Photos of Radiation Measuring Setup........................................................................................ 22 5 CONDUCTED EMISSION MEASUREMENT ........................................................................ 24 5.1 Description ................................................................................................................................. 24 6 ANTENNA REQUIREMENT .................................................................................................... 25 6.1 Standard Applicable ................................................................................................................... 25 6.2 Antenna Construction................................................................................................................. 25 7 HOPPING CHANNEL SEPARATION..................................................................................... 26 7.1 Standard Applicable ................................................................................................................... 26 7.2 Measurement Procedure...........................…

Text truncated - open the document above for the full version.

ETC Report No. : 15-05-RBF-037-01 FCC ID: HQXJRVCS1DC Sheet 22 of 96 Sheets Rev. No 2.1 4.6 Photos of Radiation Measuring Setup ETC Report No. : 15-05-RBF-037-01 FCC ID: HQXJRVCS1DC Sheet 23 of 96 Sheets Rev. No 2.1