HQXWVTX1APStand Alone Digital Wireless Transmitter

WVTX1AP INSTALLATION Connect to camera Black Ground Input Red +12VDC Input Mounting screws x4 Antenna Aligned Vertically (Perpendicular to Road) R WVTX1AP Auto Pair Digital Wireless T ransmitter Module 1. Mount the transmitter using 4 screws in a safe location to avoid impacts. 2. Connect 12 volts to the red wire and chassis ground to the black wire. 3. Connect the camera cable. 4. Secure all wires & cables. technology with Auto-Pair Digital wireless Transmitter Featuring O b s e r v a t i o n
S y s t e m s MA2A1209002-1R Our wireless technology operates at nearly the same performance level as a wired system. However, slight delays and signal reductions are possible due to application or environmental factors.? To comply with the FCC RF exposure compliance requirements, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. No change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user's authority to operate the device. IMPORTANT NOTE: Notice 1 : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Notice 2: PATENT PENDING

ETC Report No. : 12-11-RBF-014 FCC ID.:HQXWVTX1AP Sheet 1 of 7 Sheets Rev. No 2.1 CONSTRUCTED PHOTOS of EUT 1. 2. ETC Report No. : 12-11-RBF-014 FCC ID.:HQXWVTX1AP Sheet 2 of 7 Sheets Rev. No 2.1 CONSTRUCTED PHOTOS of EUT 3. 4. ETC Report No. : 12-11-RBF-014 FCC ID.:HQXWVTX1AP Sheet 3 of 7 Sheets Rev. No 2.1 CONSTRUCTED PHOTOS of EUT 5. 6.

R WVTX1AP Auto Pair Digital Wireless Product label Made In Taiwan XMMYYSSTNnnnnn WVTX1AP FCC ID label Model no.& Sn. label Product label FCC ID label Model no.& Sn. label 50 mm 18 mm 60 mm 27 mm 44 mm 24 mm LB2-1209003-1R LB2-1209004-1R LC2-1209002-1R

ETC Report No. : 12-11-RBF-014 FCC ID.:HQXWVTX1AP Sheet 4 of 7 Sheets Rev. No 2.1 CONSTRUCTED PHOTOS of EUT 7. 8. ETC Report No. : 12-11-RBF-014 FCC ID.:HQXWVTX1AP Sheet 5 of 7 Sheets Rev. No 2.1 CONSTRUCTED PHOTOS of EUT 9. 10. ETC Report No. : 12-11-RBF-014 FCC ID.:HQXWVTX1AP Sheet 6 of 7 Sheets Rev. No 2.1 CONSTRUCTED PHOTOS of EUT 11. 12. ETC Report No. : 12-11-RBF-014 FCC ID.:HQXWVTX1AP Sheet 7 of 7 Sheets Rev. No 2.1 CONSTRUCTED PHOTOS of EUT 13. 14.

Rev. No 1.0 FCC Part 15 EMI TEST REPORT of E.U.T. : Stand Alone Digital Wireless Transmitter Model : WVTX1AP FCC ID : HQXWVX1AP for APPLICANT : SYSGRATION LTD. ADDRESS : 10F, NO. 868-3, Zhongzherng Rd, Zhonghe Dist, New Taipei City 235, Taiwan (R.O.C.) Test Performed by ELECTRONICS TESTING CENTER, TAIWAN NO. 34. LIN 5, DINGFU VIL., LINKOU DIST., NEW TAIPEI CITY, TAIWAN, 24442, R.O.C. Tel:(02)26023052 Fax:(02)26010910 http://www.etc.org.tw ; e-mail : [email protected] Report Number : 12-11-RBF-014 ETC Report No. : 12-11-RBF-014 FCC ID.:HQXWVTX1AP Rev. No 1.0 TEST REPORT CERTIFICATION Applicant : SYSGRATION LTD. 10F, NO. 868-3, Zhongzherng Rd, Zhonghe Dist, New Taipei City 235, Taiwan (R.O.C.) Manufacture : SYSGRATION LTD. (1)No.26,North Industry Rd., Nan-Kan Idustrial Zone,Nan-Tou City, Nan-Tou County, Taiwan (2)10FL,No.868-3,Chung Cheng Rd., Chung Ho 235,Taipei,Taiwan, R.O.C. Description of Device : a) Type of EUT : Stand Alone Digital Wireless Transmitter b) Trade Name : Voyager c) Model No. : WVTX1AP d) Power Supply : DC 12V Regulation Applied : FCC Rules and Regulations Part 15 Subpart C I HEREBY CERTIFY THAT: The data shown in this report were made in accordance with the procedures given in ANSI C63.4, and the energy emitted by the device was founded to be within the limits applicable. I assume full responsibility for accuracy and completeness of these data. Note: 1. The result of the testing report relate only to the item tested. 2. The testing report shall not be reproduced expect in full, without the written approval of ETC. Summary of Tests Test Results Radiated Emission Pass Conducted Emission N/A Hopping Channel Separation Pass Number of Hopping frequencies used Pass Hopping Channel Bandwidth Pass Dwell Time of each frequency Pass Output Power Requirement Pass 100 kHz Bandwidth of Frequency Band Edges Requirement Pass Out-of-Band Conducted Emission Requirement Pass ETC Report No. : 12-11-RBF-014 FCC ID.:HQXWVTX1AP Rev. No 1.0 Date Test Item Received : Nov. 12, 2012 Date Test Campaign Completed : Dec. 06, 2012 Date of Issue : Dec. 06, 2012 Test Engineer : ( Jiapeng Chen, Engineer ) Approve & Authorized Signer : S. S. Liou, Section Manager EMC Dept. II of ELECTRONICS TESTING CENTER, TAIWAN ETC Report No. : 12-11-RBF-014 FCC ID.:HQXWVTX1AP Rev. No 1.0 Table of Contents Page 1 GENERAL INFORMATION ....................................................................................................... 1 1.1 Product Description...................................................................................................................... 1 1.2 Test Methodology ........................................................................................................................ 1 1.3 Test Facility.................................................................................................................................. 1 2 PROVISIONS APPLICABLE...................................................................................................... 2 2.1 Definition ..................................................................................................................................... 2 2.2 Requirement for Compliance ....................................................................................................... 3 2.3 Restricted Bands of Operation ..................................................................................................... 5 2.4 Labeling Requirement .................................................................................................................. 6 2.5 User Information .......................................................................................................................... 6 3 SYSTEM TEST CONFIGURATION .......................................................................................... 7 3.1 Justification .................................................................................................................................. 7 3.2 Devices for Tested System........................................................................................................... 7 4 RADIATED EMISSION MEASUREMENT .............................................................................. 8 4.1 Applicable Standard ..................................................................................................................... 8 4.2 Measurement Procedure............................................................................................................... 8 4.3 Measuring Instrument ................................................................................................................ 10 4.4 Radiated Emission Data ............................................................................................................. 11 4.5 Field Strength Calculation.......................................................................................................... 19 4.6 Photos of Radiation Measuring Setup........................................................................................ 20 5 CONDUCTED EMISSION MEASUREMENT ........................................................................ 21 5.1 Standard Applicable ................................................................................................................... 21 6 ANTENNA REQUIREMENT .................................................................................................... 22 6.1 Standard Applicable ................................................................................................................... 22 6.2 Antenna Construction................................................................................................................. 22 7 HOPPING CHANNEL SEPARATION..................................................................................... 23 7.1 Standard Applicable ...............................................................................................................…

Text truncated - open the document above for the full version.

ETC Report No. : 12-11-RBF-014 FCC ID.:HQXWVTX1AP Sheet 18 of 59 Sheets Rev. No 2.1 4.6 Photos of Radiation Measuring Setup