HSW-TY1SCDMCommunication Module

Copyright © Murata Manufacturing Co., Ltd. All rights reserved. September 2018 Application Note: LBAD0XX1SC, v0.5 2/11/20 Page 1 of 33 www.murata.com Type1SC Hardware Design Guidelines Version Release DateComments 0.1 10/01/2018 Initial draft 0.2 11/08/2018 Revisions following first review 0.3 03/27/2019 Revised VBAT_FEM Max Current 0.4 07/01/2019 Added FCC Notice 0.5 08/07/2019 Updated graphic in Section 2.5.7. 0.6 12/12/2019 Updated FCC ID for NB1 0.7 1/17/2020 Updated regulatory info 0.8 1/30/2020 Updated EIRP for antennas for FCC/IC 2 THIS PAGE INTENTIONALLY LEFT BLANK 3 TABLE OF CONTENTS 1 Introduction .................................................................................................................................................. 7 1.1 Scope ....................................................................................................................................... 7 1.2 Audience .................................................................................................................................. 7 1.3 Contact Information and Support ............................................................................................. 7 1.4 Text Conventions ...................................................................................................................... 7 1.5 Acronyms ................................................................................................................................. 7 1.6 Related Documents .................................................................................................................. 8 2 Introduction .................................................................................................................................................. 9 2.1 High Level Block Diagram ........................................................................................................ 9 2.2 Supported bands ...................................................................................................................... 9 2.3 Tx Output Power ...................................................................................................................... 9 2.4 Rx Sensitivity ............................................................................................................................ 9 2.5 Power Modes ........................................................................................................................... 9 LS Power Mode .................................................................................................................. 10 DS Power Mode ................................................................................................................. 10 DH0 Power Mode ............................................................................................................... 10 DH1 Power Mode ............................................................................................................... 10 DH2 Power Mode ............................................................................................................... 10 PSM Current Draw ............................................................................................................. 10 eDRX Current Draw ............................................................................................................ 11 2.6 Certification and Regulatory ................................................................................................... 12 2.7 Power Supply Range .............................................................................................................. 12 2.8 Temperature Range ................................................................................................................ 12 2.9 Mechanical Specifications ...................................................................................................... 13 2.10 Pin Layout and Descriptions ................................................................................................... 14 2.11 Reference Circuit.................................................................................................................... 23 3 Power......................................................................................................................................................... 23 3.1 Power Up Sequence .............................................................................................................. 23 3.2 Power Down Sequence .......................................................................................................... 23 3.3 Power Supply Scenarios (by Battery Type) ............................................................................ 23 LiPo Battery (3.2 ~ 4.35 V) ................................................................................................. 24 CR17450 Battery (2.2 ~ 3.0 V) ........................................................................................... 24 AA Lithium Battery (1.0 ~ 1.5 V) ......................................................................................... 24 3.4 PMU ....................................................................................................................................... 24 PMU_SHUTDOWN ............................................................................................................ 25 PMU_POWER_BUTTON ................................................................................................... 25 PMU_WAKEUP .................................................................................................................. 25 4 SIM Interface ............................................................................................................................................. 25 5 Host Interface ..........................................................................................................................................…

Text truncated - open the document above for the full version.

RE FCC ID: HSW-TY1SCDM To the certification reviewer: We are hereby applying for full modular approval of the above-referenced FCC ID, based on compliance with all of the criteria as detailed below. Sincerely, Mark Tucker Manager, Hardware Engineering Part 15 Unlicensed Single Modular Transmitter Approval Justification per 15.212 Requirement per 15.212 reference (i) The radio elements of the modular transmitter must have their own RF shielding. Shielding is provided by (patented) metal-filled resin over the module circuitry. (ii) The modular transmitter must have buffered modulation/data inputs (if such inputs are provided. All modulation and data inputs are buffered by circuitry on the transmitter chip. (iii) The modular transmitter must have its own power supply regulation. Voltage is internally regulated by the ALT1250 modem chip. (iv) The modular transmitter must comply with the antenna and transmission system requirements of §§ 15.203, 15.204(b) and 15.204(c). The EUT meets the FCC antenna Requirements. Instructions are described in Operational Description. (v) The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing for compliance with Part 15 parameters. Testing was performed with the module extended outside of the host on a special extender board, as shown in the test setup photos. (vi) The modular transmitter must be equipped with either a permanently affixed label or must be capable of electronically displaying its FCC identification number. If the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referrin g to the enclosed module. A sample of the host label is provided as an exhibit, showing the FCC identifier of the module. (vii) The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. The module complies fully with the operating requirements of Part 15 as demonstrated in the test report exhibit. (viii) The modular transmitter must comply with any applicable RF exposure requirements in its final configuration. The EUT is comply with RF exposure re requirement. RF exposure is addressed in the User Manual.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for elec- tronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or ap- pearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group EXTERNAL PHOTOGRAPHS OF EUT Front View of EUT Back View of EUT

Height Width Gap ① #1 pin - ② 2D CODE Serial Number ③ Murata mark - ④ Inspection No. SS605TP11 0.6mm 0.4mm 0.05mm ⑤ Type name 1SC revise to LBAD0XX1SC-DM 0.6mm 0.4mm 0.05mm FCC ID:XXXXXXXX 0.6mm 0.4mm 0.05mm IC:XXXXXXXXX 0.6mm 0.4mm 0.05mm ⑦ TELEC mark - ⑧ TELEC No. R 003-180242 0.6mm 0.4mm 0.05mm ⑨ TElEC No. T D180138003 0.6mm 0.4mm 0.05mm Φ1.5mm ⑥ FCC/IC Φ3.0mm Item Marking info. Character Size - 3.5*3.5mm ⑩ for ST micro 0.6mm 0.4mm 0.05mm XXXXXXXXXX SS610TP12 003-180242 IC:4492 A -TY1SCDM FCCID:HSW-TY1SCDM D180138003 RT M LBAD0XX1SC-DM ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ XXXXXXXXXX ⑩

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for elec- tronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or ap- pearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group INTERNAL PHOTOGRAPHS OF EUT Internal View of EUT

Report No: ER/2019/A0129 Page: 1 of 8 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group RF EXPOSURE REPORT OF Applicant: Murata Electronics North America 2200 Lake Park Dr #7604, Smyrna, GA 30080 USA Product Name: Type 1SC Brand Name: Murata Model No.: LBAD0XX1SC-DM Model Difference: N/A Report Number: ER/2019/A0129 FCC ID: HSW-TY1SCDM IC: 4492A-TY1SCDM FCC Rule Part Part 2.1091 IC Rule: RSS-102 issue 5 Mar. 19, 2015 Issue Date: Feb. 11, 2020 We hereby certify that: The above equipment was verified by SGS Taiwan Ltd. The evaluation in this report is in compliance with the above rule(s). The results of this report relate only to the sample identified in this report. Approved By: John Yeh / Asst. Manager Report No: ER/2019/A0129 Page: 2 of 8 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group Revision History Report Number Revision Description Issue Date Remark ER/2019/A0129 Rev.00 Original. Feb. 11, 2020 Revised By: Karen Huang Report No: ER/2019/A0129 Page: 3 of 8 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group Table of Contents 1 DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ..................................................... 4 2 MAXIMUM PERMISSIBLE EXPOSURE (MPE) ................................................................. 5 Report No: ER/2019/A0129 Page: 4 of 8 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and,…

Text truncated - open the document above for the full version.

Report No.: E2/2019/A0028 Page 1 of 153 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group ELECTROMAGNETIC EMISSIONS COMPLIANCE REPORT OF Applicant: Murata Electronics North America 2200 Lake Park Dr #7604, Sm yrna, GA 30080 USA Product Name: Type 1SC Brand Name: Murata Model No.: LBAD0XX1SC-DM Model Difference: N/A Report Number: E2/2019/A0028 FCC ID HSW-TY1SCDM IC: 4492A-TY1SCDM FCC Rule Part: 2 , 22H & 24E & 27C & 90S ISED Rule: RSS-130, 132, 133, 139 Issue Date: Feb. 10, 2020 Date of Test: Oct. 24, 2019 ~Feb. 10, 2020 Date of EUT Received: Oct. 24, 2019 We hereby certify that: The above equipment was tested by SGS Taiwan Ltd. Electronics & Communication Labor- atory The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.26-2015 and the energy emitted by the sample EUT tested as described in this report is in compliance with conducted and radiated emission limits. The test results of this report relate only to the tested sample identified in this report. Tested By: Ashton Chiu / Engineer Approved By: Jazz Huang / Asst. Supervisor Report No.: E2/2019/A0028 Page 2 of 153 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group Revision History Report Number Revision Description Issue Date Remark E2/2019/A0028 Rev.00 Original. Feb. 10, 2020 Revised By: Karen Huang Report No.: E2/2019/A0028 Page 3 of 153 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecu…

Text truncated - open the document above for the full version.

Report No.: E2/2019/A0028 Page 42 of 153 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group NB_IoT_Band26_Part90s_15kHz_QPSK_12_0_CH26692 NB_IoT_Band26_Part90s_15kHz_QPSK_12_0_CH26740 NB_IoT_Band26_Part90s_15kHz_QPSK_12_0_CH26788 Report No.: E2/2019/A0028 Page 43 of 153 Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 90 days only. 除非另有說明，此報告結果僅對測試之樣品負責，同時此樣品僅保留90天。本報告未經本公司書面許可，不可部份複製。 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. SGS Taiwan Ltd. No.134,WuKungRoad,NewTaipeiIndustrialPark,WukuDistrict,NewTaipeiCity,Taiwan24803/新北市五股區新北產業園區五工路134號 台灣檢驗科技股份有限公司 t (886-2) 2299-3279 f (886-2) 2298-0488 www.tw.sgs.com Member of SGS Group 8 OUT OF BAND EMISSION AT ANTENNA TERMINALS 8.1 Standard Applicable FCC §22.917(a), §24.238(a), §27.53(h) RSS-130 §4.7, RSS-132 §5.5, RSS-139 §6.5, RSS-139 §6.6 Out of band emissions.The power of any emission outside of the authorized operating frequency ranges must be attenuated below the transmitting power (P) by a factor of at least 43 + 10 log(P) dB. FCC §27.53(c) for B13 For operations in the 746–758 MHz band and the 776–788 MHz band, the power of any emission out- side the licensee’s frequency band(s) of operation shall be attenuated below the transmitter power (P) within the licensed band(s) of operation, measured in watts, in accordance with the following: (2) On any frequency outside the 776– 788 MHz band, the power of any emission shall be attenuated outside the band below the transmitter power (P) by at least 43 + 10 log (P) dB (-13dBm) (4) On all frequencies between 763-775 MHz and 793-805 MHz, by a factor not less than 65 + 10 log (P) dB in a 6.25 kHz band segment, for mobile and portable stations; FCC §27.53 (f) for B13 For operations in the 746-758 MHz, 775-788 MHz, and 805-806 MHz bands, emissions in the band 1559-1610 MHz shall be limited to −70 dBW/MHz equivalent isotropically radiated power (EIRP) for wideband signals, and −80 dBW EIRP for discrete emissions of less than 700 Hz bandwidth. For the purpose of equipment authorization, a transmitter shall be tested with an antenna that is representative of the type that will be used with the equipment in normal operation. FCC §27.53(c) (5) & FCC §27.53(g) for B12, 13 Compliance for operations in the 600 MHz, 698-746 MHz, 746-758 MHz and the 776-788 MHz band with this provision is based on the use of measurement instrumentation employing a resolution band- width of 100 kilohertz or greater. However, in the 100 kilohertz bands immediately outside and adjacent to a licensee’s frequency block, a resolution bandwidth of at least 30 kHz may be employed. ISED RSS-130 §4.7.1 for B12, 13 Compliance for operations in the 617-652 MHz, 663-698 MHz, 698-756 MHz and the 777-787 MHz band, the unwanted emissions in any 100 kHz bandwidth on any frequency outside the low frequency edge and the high frequency edge of each frequency block range(s), shall be attenuated below the transmitter power, P (dBW), …

Text truncated - open the document above for the full version.