I28-WYSBHVDXPWLAN/BTLE module

Compliance and Regulatory Statements FCC Compliance Statement (USA) This device complies with Part 15 rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B Digital Devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the product manuals, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, the user is encouraged to do one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced RF service technician for help. The end product must be labeled, in a visible area, with the following: Contains FCC ID: I28-WYSBHVDXP Modification Warning The user is cautioned that any changes or modifications not expressly approved by Zebra Technologies could void the user’s authority to operate the equipment. To ensure compliance, this printer must be used with fully shielded communication cables. RF Exposure Statement This transmitter complies with FCC radiation exposure limits set forth for an uncontrolled environment. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter, except in accordance with FCC multitransmitter product procedures. Canadian DOC Compliance Statement Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This Class B digital apparatus complies with Canadian ICES-003. Industry Canada (IC) Warning Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1) This device may not cause interference., 2) This device must accept any interference, including interference that may cause undesired operation of the device. The end product must be labeled, in a visible area, with the following: Contains IC: 3798B-WYSBHVDXP Approved Antenna information Only Zebra approved antennas are allowed and cannot be user replaceable. Antenna Type: WLAN Chip Gain: 3.2 dBi (2.4G); 4.2 dBi (5G) Patch Gain: 3.81 dBi (2.4G); 4.4 dBi (5G) Omnidirectional Gain 3.0 dBi (2.4G); 5.0 dBi (5G) Bluetooth Monopole: 3 dBi (2.4G) General The 802.11ax radio module has been certified as a Full Modular. Additional evaluation is required for use in all host devices. The following describes the installation procedures for the various hosts in which the module has been evaluated. Installation Instructions for Zebra printers The 802.11ax radio module is not intended for OEM Integrators or end users. it can only be installed at the grantee manufacturing facility. Important Notice to OEM integrators 1. This module is limited to OEM installation ONLY. 2. This module is limited to installation in mobile or fixed applications, according to Part 2.1091(b). 3. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations 4. For FCC Part 15.31 (h) and (k): The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with Part 15 Subpart B, the host manufacturer is required to show compliance with Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting and the evaluation should confirm that the module's intentional emissions are compliant (i.e. fundamental and out of band emissions). The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in Part 15 Subpart B or emissions are complaint with the transmitter(s) rule(s). RF trace layout guide The RF trace of the test board which was used in the FCC test is define as below, use the same RF layout for meet FCC requirement. Host integrator can contact module manufacturer for RF trace layout Gerber file. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems; Le dispositif utilisé dans la bande 5150-5250 MHz est réservé à une utilisation en intérieur afin de réduire le risque de brouillage préjudiciable aux systèmes mobiles par satellite dans le même canal; Radiation Exposure Statement This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. Thi…

Text truncated - open the document above for the full version.

5 th -Jun.2020 Ver.0.5 TAIYO YUDEN CO., LTD. TAIYO YUDEN CO., LTD. WYSBHVDXP : 11ax (2x2) +BT5.0 Wireless LAN + Bluetooth ® Module IEEE802.11ax/ac/a/b/g/n (2x2) + Bluetooth ® 5.0 WYSBHVDXP ( Under Development ) Data Report By purchase of any of products described in this document, the customer is deemed to understand and accept contents of this document. The Bluetooth ® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by TAIYO YUDEN CO., LTD. is under license. 5 th -Jun.2020 Ver.0.5 TAIYO YUDEN CO., LTD. TAIYO YUDEN CO., LTD. WYSBHVDXP : 11ax (2x2) +BT5.0 ATTENTION: This module requires device drivers that are under Japan export control. Depending on the customer’s country and application (e.g. weapons), Taiyo Yuden may not be able to provide these drivers to all customers. Please contact your local Taiyo Yuden sales office for additional information. To contact your local sales office and for additional product information, please visit www.ty-top.com. 5 th -Jun.2020 Ver.0.5 TAIYO YUDEN CO., LTD. TAIYO YUDEN CO., LTD. WYSBHVDXP : 11ax (2x2) +BT5.0 Document constituent list Control name Control No. Document Page General Items HD-AG-A191094 1/3 - 3/3 Absolute maximum ratings HD-AM-A191094 1/1 Electrical characteristics HD-AE-A191094 1/8 - 8/8 Circuit schematic HD-MC-A191094 1/1 Outline / Appearance HD-AD-A191094 1/4 - 4/4 Pin Layout HD-BA-A191094 1/3 - 3/3 Handling Precaution HQ-BA-537 1/3 - 3/3 Precautions HQ-BK-002_02 1/2 - 2/2 Rev. records Sep.-06-2019>Ver.0.1 Release Sep.-18-2019>Ver.0.2 Updated Electrical characteristics (SDIO Interface), Outline/Appearance and Pin Layout Nov.-15-2019>Ver.0.3 Updated Electrical characteristics (Power on Sequence, RF specifications) and Outline/Appearance (Recommended Metal Mask (Solder Mask) Conditions) Dec.-10-2019>Ver.0.4 Updated Outline/ Appearance (Module Pad Dimension) Jun.-5-2020>Ver.0.5 Updated Outline/ Appearance (Module Pad Dimension) 5 th -Jun.2020 Ver.0.5 TAIYO YUDEN CO., LTD. TAIYO YUDEN CO., LTD. WYSBHVDXP : 11ax (2x2) +BT5.0 Control No. HD-AG-A191094 (1/3) Control name General Items 1. Scope This specification (“Specification”) applies to the hybrid IC “WYSBHVDXP” for use Wireless LAN and Bluetooth ® module (“Product”) manufactured by TAIYO YUDEN CO., LTD. (“TAIYO YUDEN”) 2. Description ① Model: WYSBHVDXP Note: Please let us know the model (WYSBHVDXP) to order this product. ② Chip: NXP 88W9098 ③ Function: Radio frequency transceiver Module. (IEEE802.11ax/ac/a/b/g/n 2x2 and Bluetooth ® 5.0 conformity) ④ Application: Mobile printer, portable audio/ video device, wireless home audio/ video entertainment, handy terminal ⑤ Structure: Hybrid IC loaded with silicon and Gallium arsenide compound monolithic semiconductor Containment of hazardous substance in this Product： * This product conforms to RoHS Directive. ⑥ Outline: 150 pin leadless chip carrier ⑦ Marking: Part Number, Lot Number and manufacturer on Shielding Case ⑧ Features: -IEEE802.11ax/ac/a/b/g/n 2x2 and Bluetooth ® 5.0 standard -Interface: SDIO3.0, PCM -Embedded MPU for reducing loads on host processor ⑨ Security: TKIP, WEP, AES, CCMP, CMAC, WAPI, WPA/WPA2(64bit/128bit) ⑩ Country of origin: Japan or Thailand ⑪ Packing: -Packaging method: Tray -Packaging unit: TBD -Standard order quantity: TBD ⑫ Mount: SMD Type 5 th -Jun.2020 Ver.0.5 TAIYO YUDEN CO., LTD. TAIYO YUDEN CO., LTD. WYSBHVDXP : 11ax (2x2) +BT5.0 ⑬ Notes a. Limitation of Warranty i) TAIYO YUDEN provide warranties only if the product is operated under the condition set forth in this specification. Please note that TAIYO YUDEN shall not be liable for any defect and/or malfunction arising from use of the product under the terms and conditions other than the operating conditions hereof. In addition, when this product is used under environmental conditions such as over voltage which is not guaranteed, it may be destroyed in short mode. To ensure the security of customer’s product, please add an extra fuse or/and a protection circuit for over voltage. ii) In some cases, TAIYO YUDEN may use replacements as component parts of products. Such replacement shall apply only to component part of products, which TAIYO YUDEN deems it possible to replace or substitute according to (i) scope of warranty provided in this specification (e.g. electric characteristics, outline, dimension, conditions of use, reliability tests, official standard (type approvals etc.)) and (ii) quality of products. TAIYO YUDEN also ensures traceability of such replacement on production lot basis. iii) The products listed in this specification are intended for use in general electronic equipment (e.g., AV equipment, OA equipment, home electric appliances, office equipment, information and communication equipment including, without limitation, mobile phone, and PC). Please be sure to contact TAIYO YUDEN for further information before using the products for any equipment which may directly cause loss of human life or bodily injury (e.g., transportation equipment including, without limitation, automotive powertrain control system, train control system, and ship control system, traffic signal equipment, disaster prevention equipment, medical equipment, highly public information network equipment including, without limitation, telephone exchange, and base station). Please do not incorporate our products into any equipment requiring high levels of safety and/or reliability (e.g., aerospace equipment, aviation equipment, nuclear control equipment, undersea equipment, military equipment. When our products are used even for high safety and/or reliability-required devices or circuits of general electronic equipment, it is strongly recommended to perform a thorough safety evaluation prior to use of our products and to install a protection circuit as necessary. Please note that unless you obtain prior written consent of TAIYO YUDEN, TAIYO YUDEN shall not be in any way responsible for any damages incurred by you or third parties arising from us…

Text truncated - open the document above for the full version.

Regulatory Engineering Zebra Technologies Corporation 3 O ve r l o o k P o i n t | L I NCO L NS HI RE, I l l i n o i s 60069 | 847-616-5806 phone | 847-616-5806 fax | www.zebra.com Date: April 23, 2021 Federal Communications Commission Office of Engineering and Technology Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: I28-WYSBHVDXP AUTHORIZATION LETTER We, the undersigned, hereby authorize Jones Tsai in Sporton International Inc. to act on our behalf in all manners relating to FCC application for equipment authorization, including signing of all documents relating to these matters. Any and all acts carried out by Jones Tsai in Sporton International Inc. on our behalf shall have the same effect as acts of our own. If you have any acknowledgement and response, please send it to Sporton International Inc. directly. Should you have any questions or comments regarding this matter, please don’t hesitate to contact me. Confidentiality Request Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure indefinitely.  Schematic Diagram  Block Diagram  Part List  Operational Description  Tune-up Procedure Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. In additional to above mentioned documents, pursuant to Public Notice DA 04-1705 of the Commission’ s policy, in order to comply with the marketing regulations in 47 CFT §2.803 and the importation rules in 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices. We are requesting the commission to grant shot-term Regulatory Engineering Zebra Technologies Corporation 3 O ve r l o o k P o i n t | L I NCO L NS HI RE, I l l i n o i s 60069 | 847-616-5806 phone | 847-616-5806 fax | www.zebra.com confidentiality request on the following attachment(s) for 180 days after the grant as outlined in Public Notice DA 04-1705.  Internal Photos  External Photos  Test Setup Photos  User Manual It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. If you have any questions regarding this authorization, please contact me directly. ____________________ Jay Cadiz Sr. Manager, Regulatory [email protected]

Regulatory Engineering Zebra Technologies Corporation 3 Overlook Point | LINCOLNSHIRE, Illinois 60069 | 847-616-5806 phone | 847-616-5806 fax | www.zebra.com Date: May 11, 2021 Request for Modular Approval for FCC ID: I28-WYSBHVDXP Item Requirements EUT 1. The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly The module is equipped with its own shielding case. 2. The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal The module has buffer modulation / data inputs. 3. The module must contain power supply regulation on the module The module has its own power supply regulation. 4. The module must contain a permanently attached antenna, or contain a unique antenna connector, 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b) The module is SIP module with BGA, with the antenna gain WLAN: Patch Gain: 3.81 dBi (2.4G); 4.4 dBi (5G) Omnidirectional Gain 3.0 dBi (2.4G); 5.0 dBi(5G) Bluetooth: Monopole: 3 dBi (2.4G) 5. The module must demonstrate compliance in a stand-alone configuration The module was tested on evaluation board, and it’s not inside of another device during testing 6. The module must be labeled with its permanently affixed FCC ID label, or use an electronic display The module transmitter will be labeled with its own FCC ID, and for OEM integration the integration manual contains labeling instructions for the host device per Part 15.212 (vi) Regulatory Engineering Zebra Technologies Corporation 3 Overlook Point | LINCOLNSHIRE, Illinois 60069 | 847-616-5806 phone | 847-616-5806 fax | www.zebra.com 7. The module must comply with all specific rules applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee The module approved transmitter complies with all applicable rules and the integration manual contains any specific requirements addressed to the integrator and/or to the end-user of the final end-product. 8. The module must comply with RF exposure requirements The module complies with the FCC RF exposure requirements for fixed and mobile applications. RF exposure is addressed in the RF exposure exhibit. _________________________________ Jay Cadiz Sr. Manager, Regulatory Zebra Technologies Corporation 3 Overlook Point, Lincolnshire, IL 60069-4302

PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 1 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 1. Photograph of the EUT EUT: WLAN/BTLE module (Brand Name: ZEBRA / Model Name: WYSBHVDXP) PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 2 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 3 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 4 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 5 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 6 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 7 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 8 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 9 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 10 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 11 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 12 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01

Label Sample Label Location Label Top face of module

PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 13 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 2. External Photograph of the Host Host: Printer (Fixture) (Brand Name: ZEBRA / Model Name: ZQ521) PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 14 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 15 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 3. Internal Photograph of the Host PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 16 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 17 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 18 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 19 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 20 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 21 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 Bluetooth Antenna 1 (Brand Name: gigaAnt / Model Name: 3030A5645-01) PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 22 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 23 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 Bluetooth Antenna 2 (Brand Name: TAIYO YUDEN / Model Name: AH 168M245001) PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 24 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 25 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 Bluetooth Antenna 3 (Brand Name: Johanson Technology / Model Name: 2450AT07A0100) PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 26 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 WLAN Antenna 1 (Brand Name: Laird / Model Name: RD2458-5) PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 27 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 28 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 29 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 WLAN Antenna 2 (Brand Name: Pulse / Model Name: W3006) PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 30 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 31 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 WLAN Antenna 3 (Brand Name: Auden / Model Name: 220370-09) PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 32 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 33 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 WLAN Antenna 4 (Brand Name: Auden / Model Name: B91882-30) PHOTOGRAPHS OF EUT Report No.: EP0D2423 TEL : 886-3-327-3456 Page Number : 34 of 34 FAX : 886-3-328-4978 Issued Date : May 15, 2021 Report Version : 01 ─────THE END────

TEL : 886-3-327-3456 Page : 1 of 6 FAX : 886-3-328-4978 Issued Date : May 05, 2021 Form version: 200414 RF EXPOSURE EVALUATION REPORT Report No. : FA0D2423 RF EXPOSURE EVALUATION REPORT FCC ID : I28-WYSBHVDXP Equipment : WLAN/BTLE module Brand Name : ZEBRA Model Name : WYSBHVDXP Applicant : Zebra Technologies Corporation 3 Overlook Point, Lincolnshire, IL 60069, United States Manufacturer : Zebra Technologies Corporation 3 Overlook Point, Lincolnshire, IL 60069, United States Standard : 47 CFR Part 2.1091 We, SPORTON INTERNATIONAL INC has been evaluated this product in accordance with 47 CFR Part 2.1091 and it complies with applicable limit. Sporton Lab is accredited to ISO 17025 by Taiwan Accreditation Foundation (TAF code: 1190) and the FCC designation No. TW1190 under the FCC 2.948(e) by Mutual Recognition Agreement (MRA) in FCC evaluation. The results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory, the test report shall not be reproduced except in full SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.) Approved by: Cona Huang / Deputy Manager TEL : 886-3-327-3456 Page : 2 of 6 FAX : 886-3-328-4978 Issued Date : May 05, 2021 Form version: 200414 RF EXPOSURE EVALUATION REPORT Report No. : FA0D2423 Table of Contents 1. DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ............................................................................. 4 2. MAXIMUM RF AVERAGE OUTPUT POWER AMONG PRODUCTION UNITS ........................................ 5 3. RF EXPOSURE LIMIT INTRODUCTION .................................................................................................... 5 4. RADIO FREQUENCY RADIATION EXPOSURE EVALUATION ............................................................... 6 4.1. Standalone Power Density Calculation ............................................................................................. 6 4.2. Collocated Power Density Calculation ............................................................................................... 6 TEL : 886-3-327-3456 Page : 3 of 6 FAX : 886-3-328-4978 Issued Date : May 05, 2021 Form version: 200414 RF EXPOSURE EVALUATION REPORT Report No. : FA0D2423 History of this test report Report No. Version Description Issued Date FA0D2423 Rev. 01 Initial issue of report May 05, 2021 TEL : 886-3-327-3456 Page : 4 of 6 FAX : 886-3-328-4978 Issued Date : May 05, 2021 Form version: 200414 RF EXPOSURE EVALUATION REPORT Report No. : FA0D2423 1. Description of Equipment Under Test (EUT) Product Feature & Specification EUT Type WLAN/BTLE module Brand Name ZEBRA Model Name WYSBHVDXP FCC ID I28-WYSBHVDXP Wireless Technology and Frequency Range WLAN 2.4GHz Band: 2400 MHz ~ 2483.5 MHz WLAN 5.2GHz Band: 5150 MHz ~ 5250 MHz WLAN 5.3GHz Band: 5250 MHz ~ 5350 MHz WLAN 5.6GHz Band: 5470 MHz ~ 5725 MHz WLAN 5.8GHz Band: 5725 MHz ~ 5825 MHz Bluetooth: 2400 MHz ~ 2483.5 MHz Mode WLAN: 802.11a/b/g/n/ac HT20/HT40/VHT20/VHT40/VHT80 Bluetooth BR/EDR/LE HW Version Revision F SW Version 17.68.01.p13 EUT Stage Identical Prototype Remark: The above EUT's information was declared by manufacturer. Please refer to the specifications or user's manual for more detailed description. WLAN Antenna Information 1 Ant. Type Dipole Antenna connector U.FL 2 Ant. Type Chip Antenna connector U.FL Model No. RD2458-5 Brand Name Laird Model No. W3006 Brand Name Pulse Peak Gain (dBi) Peak Gain (dBi) 2400~2483.5MHz 3.0 5470~5725MHz 5.0 2400~2483.5MHz 3.2 5470~5725MHz 4.2 5150~5250MHz 5.0 5725~5850MHz 5.0 5150~5250MHz 4.2 5725~5850MHz 4.2 5250~5350MHz 5.0 5250~5350MHz 4.2 3 Ant. Type Mylar Antenna connector U.FL 4 Ant. Type Mylar Antenna connector U.FL Model No. 220370-09 Brand Name Auden Model No. B91882-30 Brand Name Auden Peak Gain (dBi) Peak Gain (dBi) 2400~2483.5MHz 3.81 5470~5725MHz 3.19 2400~2483.5MHz 0.3 5470~5725MHz 4.4 5150~5250MHz 2.18 5725~5850MHz 2.69 5150~5250MHz 3.4 5725~5850MHz 4.0 5250~5350MHz 2.71 5250~5350MHz 3.3 Bluetooth Antenna Information 1 Brand Name gigaAnt 2 Brand Name TAIYO YUDEN Ant. Type Monopole Antenna Peak Gain 2.7 dBi Ant. Type Monopole Antenna Peak Gain 3 dBi connector U.FL Model No. 3030A5645-01 connector U.FL Model No. AH 168M245001 3 Brand Name Johanson Technology Ant. Type Monopole Antenna Peak Gain 1 dBi connector U.FL Model No. 2450AT07A0100 Reviewed by: Jason Wang Report Producer: Paula Chen TEL : 886-3-327-3456 Page : 5 of 6 FAX : 886-3-328-4978 Issued Date : May 05, 2021 Form version: 200414 RF EXPOSURE EVALUATION REPORT Report No. : FA0D2423 2. Maximum RF average output power among production units Band Average Power (dBm) Ant 1 Ant 2 Ant 1+2 2.4GHz WLAN 17 17 14 5.2GHz WLAN 15 14 13 5.3GHz WLAN 14 14 13 5.5GHz WLAN 14 14 13 5.8GHz WLAN 14 14 13 Band Average Power (dBm) Bluetooth 12 3. RF Exposure Limit Introduction According to ANSI/IEEE C95.1-1992, the criteria listed in Table 1 shall be used to evaluate the environmental impact of human exposure to radio frequency (RF) radiation as specified in §1.1310. The MPE was calculated at 20 cm to show compliance with the power density limit. The following formula was used to calculate the Power Density: 퐒= 퐏퐆 ퟒ훑퐑 ퟐ Where: S = Power Density P = Output Power at Antenna Terminals G = Gain of Transmit Antenna (linear gain) R = Distance from Transmitting Antenna TEL : 886-3-327-3456 Page : 6 of 6 FAX : 886-3-328-4978 Issued Date : May 05, 2021 Form version: 200414 RF EXPOSURE EVALUATION REPORT Report No. : FA0D2423 4. Radio Frequency Radiation Exposure Evaluation 4.1. Standalone Power Density Calculation Band Maximum Antenna Gain (dBi) Maximum Power (dBm) Maximum EIRP (dBm) Maximum EIRP (W) Average EIRP (mW) Power Density at 20cm (mW/cm^2) Limit (mW/cm^2) Power Density / Limit WLAN2.4GHz Band 3.81 17.0 20.8 0.12 120.23 0.024 1.000 0.024 WLAN5GHz Band 5.0 15.0 20.0 0.10 100.00 0.020 1.000 0.020 Bluetooth 3.0 1…

Text truncated - open the document above for the full version.

TEL: 886-3-327-0868 Page Number : 1 of 14 FAX: 886-3-327-0855 Issued Date : May 11, 2021 Report Template No.: BU5-FR15EWL AC MA Version 2.4 Report Version : 01 FCC CO-LOCATION RADIO TEST REPORT Report No. : FR0D2423F FCC CO-LOCATION RADIO TEST REPORT FCC ID : I28-WYSBHVDXP Equipment : WLAN/BTLE module Brand Name : ZEBRA Model Name : WYSBHVDXP Applicant : Zebra Technologies Corporation 3 Overlook Point, Lincolnshire, IL 60069, United States Manufacturer : Zebra Technologies Corporation 3 Overlook Point, Lincolnshire, IL 60069, United States Standard : FCC Part 15 Subpart E §15.407 The product was received on Mar. 08, 2021 and testing was started from May 03, 2021 and completed on May 03, 2021. We, Sporton International Inc. Wensan Laboratory, would like to declare that the tested sample ha…

Text truncated - open the document above for the full version.