P/N: 165M0014-10Dec. 01/06 Initial Issue ProTec AUTOMATIC IDENTIFICATION SYSTEM HARDWARE AIS PART NUMBER AISA1000-10 INSTALLATION AND OPERATION MANUAL Marine Systems Aviation Recorders Initial Issue Dec. 01/06 165M0014-10 Page ii AIS Hardware I&O Manual 165M0014-10 Initial Issue Dec. 01/06 EXPORT CONTROL STATEMENT AIS TECHNOLOGY / DATA: “This Automatic Identification System (AIS) Products/Technology is being exported from the United States in accordance with the Export Administration Regualtions (ECCN #7E994, #4E992), No License Re- quired (NLR). Diversion contrary to U.S. law is prohibited. In accor- dance with U.S. Law (Title 15 CFR Part 746 and Supplement No. 1 to Part 774; and Title 31 CFR) resale/reexport or transfer to certain des- ignated countries is prohibited without the prior written consent of the U.S. Department of Commerce.” This manual contains date sensitive information. To verify the latest revision level of this manual, visit our document download site at http://www.L-3ar.net. ECopyright 2006 by L-3 Communications. All rights reserved. No part of this manual may be re- produced or utilized in any form or by any means, elec- tronic or mechanical, including photocopying, record- ing, or by information storage and retrieval system, without permission in writing. Inquiries should be addressed to: L-3 Communications Aviation Recorders Publications Vendor Code: 06141 P. O. Box 3041 Sarasota, Florida 34230 Phone: (941) 371–0811 FAX: (941) 377–5591 Marine Systems Aviation Recorders Initial Issue Dec. 01/06 165M0014-10 Page iii GENERAL This product and related documentation must be reviewed for familiarization with safety markings and instructions before operation. This board was constructed in an ESD (electroćstatic discharge) protected environment. This is because most of the semiconductor devices used in this board are susceptible to damage by static discharge. Depending on the magnitude of the charge, device substrates can be punctured or destroyed by contact or mere proximity of a static charge. The results can cause degradation of device perforĆ mance, early failure, or immediate destruction. These charges are generated in numerous ways such as simple contact, separation of materials, and normal motions of persons working with static sensitive devices. When handling or servicing equipment containing static sensitive devices, adequate precautions must be taken to prevent device damage or destruction. Only those who are thoroughly familiar with industry accepted techniques for handling static senĆ sitive devices should attempt to service circuitry with these devices. In all instances, measures must be taken to prevent static charge buildćup on work surfaces and persons handling the devices. Marine Systems Aviation Recorders Initial Issue Dec. 01/06 165M0014-10 Page iv RETURN MATERIAL POLICY Components and spare parts purchased from L–3 that are discrepant for any of the following reasons may be re- turned immediately provided the extended value of the parts are in excess of $100.00. 1.Overshipments Quantity of parts received in excess of quantity specified on purchase order. 2.Wrong Part Numbers Receipt of parts numbered other than those identified on a customer order where L–3 has not advised the cus- tomer by purchase order acknowledgment, by telex, or by notification on the shipping document that the received part is a replacement for the ordered part. 3.Parts Nonconforming to Specifications If the extended value of the items is less than $100.00, the items are to be scrapped instead of returned. When this occurs, notification must be sent to L–3 advising: (1) the reason for the rejection; (2) the items are less than $100.00 in extended value and have been scrapped, and; (3) whether credit or replacement is desired. If you wish to return material to L–3 for reasons other than warranty returns or those specified above, please contact an L–3 Account Administrator for authorization before proceeding. A Return Authorization Number will be assigned at this time. Your request should specify the relevant Return Authorization Number, purchase order number, part num- ber, quantity and the reason you wish the part returned. To assist us in processing these items more efficiently, we ask that all returned goods be accompanied by paperwork that clearly indicates the following: 1.Reason for return. 2.Purchase Order Numbers. 3.Correspondence Reference Number. 4.Return Authorization Number. 4.Copies of returned goods paperwork should be mailed to: L–3 COMMUNICATIONS CORPORATION AVIATION RECORDERS DIVISION P. O. Box 3041 Sarasota, FL 34230–3041 Attn: Tom Meloche / Marine Systems Product Support Department 5.Parts returned under the above conditions should be addressed to: L–3 COMMUNICATIONS CORPORATION AVIATION RECORDERS DIVISION 6000 E. Fruitville Road Sarasota, FL 34232 Attn: SERVICE DEPARTMENT Component and spare parts purchased from L–3 that have been on the customer’s shelf for more than 10 weeks from date of receipt; have been installed in a component or on a vessel, are not covered by this procedure. Such parts may be covered by warranty in which case they should be returned through normal warranty channels. Marine Systems Aviation Recorders Initial Issue Dec. 01/06 165M0014-10 Page v RETURN OF MATERIAL UNDER WARRANTY 1.Material should be returned to the following address: L–3 COMMUNICATIONS CORPORATION AVIATION RECORDERS DIVISION 6000 E. Fruitville Road Sarasota, FL 34232 Attn: WARRANTY RETURNS 2.For returning overseas shipments, the following customs broker must be used: L–3 COMMUNICATIONS CORPORATION AVIATION RECORDERS DIVISION c/o A.J. Arango Air Cargo Bldg. Hoover Blvd. Tampa Int’l Airport Tampa, Florida 33634 Tel: (813) 248–9220 Fax: (813) 248–6013 To ensure prompt handling of material returned under warranty, your return order and shipment should clearly identify the item as a warranty return, and a copy of such return order should accompany the shipment. Status of warranty…

Text truncated - open the document above for the full version.

Cover Letter(s)

Aviation Recorders P.O. Box3041 Sarasota, FL 34230-3041 941-371-0811 Attn: Reviewing Engineer Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: In response to question #4 concerning if the device is certified as Class A or Class B. The L-3 AIS is a Class A device. Robin S. Speidel Senior QA Manager L-3 Communications Aviation Recorders

Operational Description

Automatic Identification System (AIS) The L-3 Automatic Identification System (AIS) is a collision avoidance tool, mandated by IMO SOLAS V, to improve the situational awareness of the bridge crew while facilitating communication between vessels. Identifies radar contacts by MMSI Access to accurate positional information for AIS-equipped vessels Text messaging between vessels and/or shore station facilitating communication of maneuvering intentions or safety alerts Compact and robust single-box design Ability to display AIS targets on ECDIS/ECS/ARPA with detailed navigational information Low cost of ownership IMO compliant L-3 COMMUNICATIONS’ AUTOMATIC IDENTIFICATION SYSTEM Rev. G MAR002 For additional information contact: The technical information contained in the marketing brochure(s) does not contain “technology” as defined by the General Technology Note in Export Administration Regulations (EAR) Supplement number 2 to Part 744 and is, therefore, considered as publicly released as defined in Part 734.7(4). The L-3 AIS is an IMO compliant transponder with internal GPS in a compact single-unit design. Also available is the L-3 ECS, an optional navigational software package with ENC. Fully compatible with all ECDIS/ECS systems and compliant to the NMEA standard for AIS display, the L-3 ECS can run on any Windows platform and is available to provide detailed AIS contact display without the additional purchase of an ECDIS/ECS system. Physical Power Requirements GPS Internal 12-Channel GPS Receiver Height Depth Width Weight 3.25 in (8.26 cm) 6.38 in (16.21 cm) 7.25 in (18.41 cm) 5.6 lbs (2.54 kg) Nominal: Receive: Transmit: 24 Vdc - 10 amp Supply 0.6 Amps 6.0 Amps L-3 AIS base stations and transponders have been successfully applied in the safe an efficient operation of ports worldwide including New Orleans, Houston, Valdez, Tampa, Suez, Turkey, and Ras Tanura. With over five years of field experience in the construction, maintenance and operation of AIS mobiles and base stations, as well as the integration of AIS into VTS/VTIS applications, L-3 is a leader in the application of AIS technology to marine operations. L-3 AIS Users Basic Display Integral IMO-Compliant Minimum Keyboard Display (MKD) Extended Display Windows based L-3 Electronic Charting System or Target Display System DGPS Optional DGPS Capability 6000 Fruitville Road Sarasota, FL 34232 P: 941 379 1660 F: 941 377 5591 www.L-3com.com 1 2 - 2 4 V D C BLACK (-) RED (+) GREEN (BIIT 1) WHITE (BIIT 2) GPS ANT VHF ANT RATE OF TURN NMEA 0183 RS 422 CH 2 HEADING NMEA 0183 RS 422 CH 3 PC/EXT APP. NMEA 0183 RS 422 CH 4 POSITION NMEA 0183 RS 422 CH 1 ECDIS/ARPA NMEA 0183 RS 422 CH 5 LONG RANGE NMEA 0183 RS 422 CH 8 Approvals FCC USCG 16.155/9/0 MED Wheelmark 734.2/0050-1/2003 Specifications subject to change without notice. For up to date information go to www.L-3ar.com/Products L-3 Aviation Recorders Quality Management System is ISO 9001:2000 and AS9100:2004 Rev. B Certified

Parts List/Tune Up Info

Page 1 of 26 P.O. Box 3041 Sarasota, Florida 34230 Cage Code: 06141 ACCEPTANCE TEST PROCEDURE for the Automatic Identification System Document No. 905-M0308-06 Revision: L Original signatures on file with EDC: Phillip Potts, Manufacturing Test Engineer 6/17/04 James Fulmele, Manufacturing Test Manager6/17/04 Robin Speidel , QA Engineer6/17/04 Frank Doran, V.P. Engineering6/17/04 Limited Rights Legend Notice to persons receiving this document and/or data: This document and/or data contains information in which L-3 Communications Corporation, Aviation Recorders Division has a protectable interest and is subject to change without notice. The use, duplication, and/or disclosure by persons receiving this document and/or data may be subject to restrictions. No part of this document and/or data contained herein may be used in any form to design, manufacture, and/or test anything without written permission from L-3 Communications Corporation, Aviation Recorders Division. Document No: 905-M0308-06 Revision: L Page 2 of 25 Record of Revisions RevDescriptionDate Approved By A ECO10122 Added receiver sensitivity test and transmitter test; removed various tests to reflect current testing requirements 08-01- 03 M. Wright B ECO10151 Removed Performance Checks; added BBM and ABM tests 08-25- 03 M. Wright CECO10165 Add 4.3.2; add steps to 4.4.2 09-08- 03 M. Wright DECO10175 Remove 4.11; add and remove steps in 4.4.2 09-11- 03 M. Wright EECO10198 Change tolerances in 4.4.2 10-02- 03 M. Wright FECO10277 Eliminate low power SINAD 12-11- 03 P. Potts GECO 10484 Re-write to reflect sequence of tests.6-17-04P. Potts H ECO 10560 Correct power specifications on Data sheet8/11/04P. Potts J ECO 10980 Correct Deviation and General Test plan7/13/05 P. Potts KECO 11389 Updated SINAD test3/7/06P. Potts LECO 11508 Deviation incorrect5/9/06P. Potts Document No: 905-M0308-06 Revision: L Page 3 of 25 1SCOPE This procedure describes the acceptance test for the Automatic Identification System. 2APPLICABLE DOCUMENTS IEC 61993-2Maritime navigation and radiocommunication equipment and systems – Automatic identification systems (AIS) 3TEST REQUIREMENTS 3.1General Test Requirements 3.1.1Upon approval this procedure will become a released document and will be under Engineering Document Center (EDC) control. 3.1.2If errors or omissions are found which require changes to this test procedure, the current procedure shall be red-lined, dated, and signed by the cognizant Test Engineer and Quality Assurance (QA) Representative. The Test Engineer shall write an ECO in accordance with QAP 5.4 and, within 10 days, submit the ECO for incorporation. This red-lined test procedure shall be valid for only 10 days without an ECO submittal by the Test Engineer. If an ECO has been submitted by the Test Engineer, then the red-lined test procedure shall be valid until the ECO has been incorporated. 3.1.3Before any data is recorded, the test technician is to verify he/she has the latest revision level of procedure and data record. The technician is also required to complete the first sheet of the data record except completion date. If the system under test consists of more than one unit, list all P/Ns and S/Ns on the Data Record. The data record, when completed will be stored per Operations Directory Policy 3.6 retention period for Test Records or as required per contract. All entries are to be made in INK and must be legible. 3.1.4If more than one technician is involved in completing the procedure, the following steps will be followed: a.All technicians involved in testing Unit Under Test ("UUT") will stamp the first sheet of the data record next to the line "TESTED BY". b.At the test step where the technician begins testing he/she will stamp the data record. The stamp is to be placed at the far right side of the page, next to the test results. 3.1.5If the results of a test are out-of-limits, the technician will write the results on the data record and circle the entry. After the out-of-limits condition has been corrected, the technician will make a single strike through the out-of-limits readings, write the new result to the side, and stamp the entry. DO NOT erase the original reading or use "white out" under any circumstances. Document No: 905-M0308-06 Revision: L Page 4 of 25 3.1.6When an out-of-limits condition cannot be corrected through normal methods, the technician is instructed to notify his/her supervisor. The problem will be turned over to Test Engineering or Design Engineering for resolution. If management decides to ship the unit with the defect, a Management Review and Disposition form must be completed. 3.1.7If an error is made while entering data onto the data record, the correction will be made in the following manner: Make a single strike through the entry such that it is still readable. Write the correction at a convenient location and initial or stamp the correction. Notify the QA Representative and she or he will also initial or stamp the correction. DO NOT erase the mistake or use "white out" under any circumstances. 3.1.8Upon successful completion of testing, review the test data sheets for any out of spec. entries and missing entries. (N/A shall be entered where there is no applicability.) Paragraphs that are applicable, but for which there is no data to be recorded, shall have the word "none" or a dash entered in the space. 3.1.9Test results which are to be recorded on the data record shall be indicated in the test procedure by the word "RECORD" or "CHECK". 3.1.10DANGER, CAUTION and NOTE shall be used to highlight important information as follows: DANGER-UPPER CASE BOLD LETTERING SHALL BE USED TO HIGHLIGHT PRECAUTIONARY MEASURES, WHICH IF NOT FOLLOWED, COULD RESULT IN INJURY TO PERSONNEL. CAUTION-UPPER CASE BOLD LETTERING SHALL BE USED TO HIGHLIGHT PRECAUTIONARY MEASURES, WHICH IF NOT FOLLOWED, COULD RESULT IN EQUIPMENT DAMAGE. NOTE: May be used to reference special instructions. While performing all alignments, troubleshooti…

Text truncated - open the document above for the full version.

Parts List/Tune Up Info

FIND_NO COMPONENT DESC 1 205M028701 "PWA,UAIS CH 70 BD" 2 1409800065 "INSUL,XTAL,MYLAR,USE WITH" 3 0720018000 "XTAL,MATCHED PAIR 16.9MHZ" 4 0910002000 "FLTR,4 POLE 455KHZ CER" 5 0640059001 "SHIELD,FINGER STOCK" 6 0769800694 "XTAL,139.625MHZ,HC-49/U" 7 0769800710 "XTAL,16.445MHZ,10PPM" 1 206M028700 "PWB,CHANNEL 70" 2 2760200004 "WIRE,#28,SOL, WHT, 600V" 3 2760200112 "WIRE,MAGNET,#32,CLASS130" 4 0600100056 EPK (EPS) 608 PART A & B 5 2769800195 "WIRE,JUMPER,#22 SOLID .25" C701 3963610004 "CAP,10UF,16V,TANT,3528" C702 3963610004 "CAP,10UF,16V,TANT,3528" C703 3964410009 "CAP,NP0,100PF,100V,5%" C704 3960418009 "CAP,NP0,180PF,100V,0805" C705 3964403909 "CAP,NP0,39PF,100V,0805" C706 3963610004 "CAP,10UF,16V,TANT,3528" C707 3962010002 "CAP,X7R,.1,50V,10%,0805" C708 3963610004 "CAP,10UF,16V,TANT,3528" C709 3962010002 "CAP,X7R,.1,50V,10%,0805" C710 3962010002 "CAP,X7R,.1,50V,10%,0805" C712 3967001209 "CAP,F,NPO,50V,12.0PF,0805" C713 3961300159 "CAP,NPO,1.5PF,100V,1206" C714 3967001209 "CAP,F,NPO,50V,12.0PF,0805" C715 3961200339 "CAP,NPO,3.9PF,100V,0805" C716 3962010000 "CAP,F,CER,50V,1000PF,0805" C717 3962010002 "CAP,X7R,.1,50V,10%,0805" C718 3962010000 "CAP,F,CER,50V,1000PF,0805" C719 3962010000 "CAP,F,CER,50V,1000PF,0805" C720 3967001209 "CAP,F,NPO,50V,12.0PF,0805" C721 3960410001 "CAP,F,CER,1000PF,200V,5%," C722 3962010000 "CAP,F,CER,50V,1000PF,0805" C723 3961300479 "CAP,NP0,4.7PF,100V,1206" C724 3962010001 "CAP,F,CER,50V,.01UF,10%," C725 3962010000 "CAP,F,CER,50V,1000PF,0805" C726 3969800057 "CAP,F,200V,7.5PF,0805,NPO" C727 3969800044 "CAP,.027UF,16V,FILM,SMT" C728 3962010001 "CAP,F,CER,50V,.01UF,10%," C729 3962022000 "CAP,X7R,2200PF,50V,0805" C730 3962010001 "CAP,F,CER,50V,.01UF,10%," C731 3967001209 "CAP,F,NPO,50V,12.0PF,0805" C732 3969800057 "CAP,F,200V,7.5PF,0805,NPO" C733 3962010002 "CAP,X7R,.1,50V,10%,0805" C734 3962010002 "CAP,X7R,.1,50V,10%,0805" C735 3969800039 "CAP,F,X7R,100V,.1UF,1206" C737 3962000003 "CAP,X7R,.047UF,50V,0805" C738 3963647003 "CAP,F,STAN,16V,4.7UF,3528" C739 3962010002 "CAP,X7R,.1,50V,10%,0805" C740 3962000003 "CAP,X7R,.047UF,50V,0805" C741 3962010002 "CAP,X7R,.1,50V,10%,0805" C742 3962010002 "CAP,X7R,.1,50V,10%,0805" C743 3962010002 "CAP,X7R,.1,50V,10%,0805" C744 3962010002 "CAP,X7R,.1,50V,10%,0805" C745 3962010002 "CAP,X7R,.1,50V,10%,0805" C746 3962010002 "CAP,X7R,.1,50V,10%,0805" C747 3962010002 "CAP,X7R,.1,50V,10%,0805" C748 3963610004 "CAP,10UF,16V,TANT,3528" C749 3963610004 "CAP,10UF,16V,TANT,3528" C750 3960404709 "CAP,CERT,100V,47PF,5%," C751 3962010002 "CAP,X7R,.1,50V,10%,0805" C752 3962010001 "CAP,F,CER,50V,.01UF,10%," C753 3962010002 "CAP,X7R,.1,50V,10%,0805" C754 3961301009 "CAP,NP0,10PF,100V,0805" C755 3962010002 "CAP,X7R,.1,50V,10%,0805" C756 3962010002 "CAP,X7R,.1,50V,10%,0805" C757 3962010002 "CAP,X7R,.1,50V,10%,0805" C758 3962010002 "CAP,X7R,.1,50V,10%,0805" C759 3962010002 "CAP,X7R,.1,50V,10%,0805" C760 3962010002 "CAP,X7R,.1,50V,10%,0805" C761 3969800039 "CAP,F,X7R,100V,.1UF,1206" C762 3969800039 "CAP,F,X7R,100V,.1UF,1206" C763 3969800039 "CAP,F,X7R,100V,.1UF,1206" C764 3969800039 "CAP,F,X7R,100V,.1UF,1206" C765 3961200159 "CAP,NP0,1.5PF,100V,0805" C766 3963610004 "CAP,10UF,16V,TANT,3528" C767 3962010002 "CAP,X7R,.1,50V,10%,0805" C768 3962010002 "CAP,X7R,.1,50V,10%,0805" C769 3962010002 "CAP,X7R,.1,50V,10%,0805" J701 0639802090 "CONN,HEADER,4C" J702 0280054001 "CONN,HDR,34C,RT ANG,DUAL" J703 0280054003 "CONN,HDR,30CONTACT,2ROW" L701 0559800271 "COIL,VAR,303-765UH" L702 0559800269 "COIL,VAR,.071-.081UH,7MM" L703 0559800269 "COIL,VAR,.071-.081UH,7MM" L704 0559800269 "COIL,VAR,.071-.081UH,7MM" L705 0559800345 "COIL,VAR,.120-.150UH,7MM" Q701 0880007002 "XSTR, DUAL GATE FET" Q702 2631600260 "XSTR,N CHAN,JFET,SOT-23" Q703 2631622220 "XSTR,NPN,SI,SINGLE,40VCE," Q704 0880007002 "XSTR, DUAL GATE FET" Q705 2631600252 "XSTR,PNP,SI,60VCE,225MW," R701 6922127409 "RES,F,TF,274,1%,.125W,100" R702 6912168101 "RES,68.1K,SMT,0805" R703 6912110000 "RES,1K,SMT,0805" R704 0060002000 "RES,0 OHM,1/8W JMPR AXIAL" R705 6912113001 "RES,13K,SMT,0805" R706 6912147509 "RES,475 OHM,SMT,0805" R707 6912110001 "RES,F,TF,10K,1%,.1W,100" R709 6912122109 "RES,221 OHM,SMT,0805" R710 6912104759 "RES,47.5 OHM,SMT,0805" R711 6912110000 "RES,1K,SMT,0805" R712 6912143200 "RES,4.32K,SMT,0805" R713 6922101009 "RES,FIX,TF,10OHM,1%,.125W" R714 6912115000 "RES,1.5K,SMT,0805" R715 2019800606 "POT,5K,SMD,4MM,5T,SIDE AD" R716 6912120001 "RES,20K,SMT,0805" R717 6912143201 "RES,43.2K,SMT,0805" R718 6912110002 "RES,F,TF,100K,1%,.1W,100" R719 6912151102 "RES,511K,SMT,0805" R720 6912147500 "RES,4.75K,SMT,0805" R721 6912147500 "RES,4.75K,SMT,0805" R722 6912147502 "RES,475K,SMT,0805" R724 6912182500 "RES,8.25K,SMT.0805" R725 6912101829 "RES,18.2 OHM,SMT,0805" R726 6912130109 "RES,301 OHM,SMT,0805" R727 6912130109 "RES,301 OHM,SMT,0805" R728 6912110009 "RES,F,TF,100,1%,.10W," R729 6912122109 "RES,221 OHM,SMT,0805" R730 6912110009 "RES,F,TF,100,1%,.10W," R731 6912115000 "RES,1.5K,SMT,0805" R732 6922127401 "RES,F,TF,27.4K,1%,.125W," R733 6912113001 "RES,13K,SMT,0805" R734 0060002471 "RES,470 OHM,5%,1/8W AXIAL" R735 6912115000 "RES,1.5K,SMT,0805" R736 6913800001 "JMPR,0805,SMT" R737 6923800001 "RES,JUMPER,1206,ZERO OHM," R738 6912118202 "RES,182K,SMT,0805" R739 6912147500 "RES,4.75K,SMT,0805" R740 6912102219 "RES,22.1 OHM,SMT,0805" R741 6912110001 "RES,F,TF,10K,1%,.1W,100" R742 6922143201 "RES,F,TF,43.2K,1%,1206" R743 6922147500 "RES,F,TF,4.75K,1%,.125W," R744 6922147509 "RES,F,TF,475.0,1%,0.125W," R745 6912147500 "RES,4.75K,SMT,0805" R746 0060002472 "RES,4.7K 5%,.25W AXIAL" R747 6922101009 "RES,FIX,TF,10OHM,1%,.125W" R748 6912115000 "RES,1.5K,SMT,0805" R749 0060002000 "RES,0 OHM,1/8W JMPR AXIAL" R750 6923800001 "RES,JUMPER,1206,ZERO OHM," R751 6923800001 "RES,JUMPER,1206,ZERO OHM," R752 0060002000 "RES,0 OHM,1/8W JMPR AXIAL" R753 0060002000 "RES,0 OHM,1/8W JMPR AXIAL" R755 0060002000 "RES,0 OHM,1/8W JMPR AXIAL" R756 0060002472 "RES,4.7K 5%,.25W AXIAL" R757 0060002000 "RES,0 OHM,1/8W JMPR AXIAL" R758 00600020…

Text truncated - open the document above for the full version.

Parts List/Tune Up Info

FIND_NO COMPONENT DESC 1 206M002312 "PWB,XCVR, AIS MOBLE" 2 0640032000 "TAB, GROUND FOR S-AV6" 3 024M058900 CABLE ASSY RF INTERNAL 5 298M067300 "HEATSINK,V2 MAIN PWA" 6 0602100002 DOW CORNING 340 HEAT SINK 7 2299800502 "SCR, CAP, 4-40 X 1/4" 8 0601100002 LOCTITE 222 THREADLOCKER 9 0070016000 "BRKT, MOUNTING, LEFT" 10 0070016001 "BRKT, MOUNTING, RIGHT" 11 2290200074 "SCR,PNH ,4-40 X5/16" 12 NAS671C4 "NUT,HEX" 15 2730200036 "WASHER,#4,SPLIT LOCK" C1 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C2 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C3 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C5 3961818001 "CAP,.018UF,25V,X7R,SMT,06" C6 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C7 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C10 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C11 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C12 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C13 3969800479 "CAP,4.7PF,50V,NP0,SMT,060" C22 3962033009 "CAP,F,CER,50V,330PF,0603," C23 3962000004 "CAP,F,CER,50V,1000PF,0603" C24 3963610003 "CAP,1UF,16V,TANT,3216" C25 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C26 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C27 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C28 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C29 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C36 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C38 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C39 3963610005 "CAP,F,STAN,16V,100UF,7343" C40 3963610005 "CAP,F,STAN,16V,100UF,7343" C42 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C43 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C44 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C45 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C46 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C51 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C58 3963610004 "CAP,10UF,16V,TANT,3528" C59 3960810009 "CAP,100PF,25V,NP0,SMT,060" C60 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C61 3961182009 "CAP,820PF,50V,NP0,SMT,060" C62 3960822009 "CAP,220PF,25V,NP0,SMT,060" C63 3961822000 "CAP,2200PF,25V,X7R,SMT,06" C64 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C66 3960810009 "CAP,100PF,25V,NP0,SMT,060" C67 3960801009 "CAP,10PF,25V,NP0,SMT,0603" C68 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C69 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C70 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C71 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C73 3960839009 "CAP,390PF,25V,NP0,SMT,060" C74 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C76 3962033009 "CAP,F,CER,50V,330PF,0603," C77 3962000004 "CAP,F,CER,50V,1000PF,0603" C78 3963610003 "CAP,1UF,16V,TANT,3216" C79 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C80 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C81 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C82 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C83 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C91 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C92 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C93 3963610005 "CAP,F,STAN,16V,100UF,7343" C94 3963610005 "CAP,F,STAN,16V,100UF,7343" C96 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C97 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C98 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C99 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C100 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C105 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C112 3963610004 "CAP,10UF,16V,TANT,3528" C113 3960401209 "CAP,COG,12PF,100PPM,0603" C114 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C115 3960822009 "CAP,220PF,25V,NP0,SMT,060" C116 3962033009 "CAP,F,CER,50V,330PF,0603," C117 3969800053 "CAP,F,CERT,50V,270PF,10%," C118 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C120 3960810009 "CAP,100PF,25V,NP0,SMT,060" C121 3960801009 "CAP,10PF,25V,NP0,SMT,0603" C122 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C123 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C124 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C125 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C127 3960839009 "CAP,390PF,25V,NP0,SMT,060" C128 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C130 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C132 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C133 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C139 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C140 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C141 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C142 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C143 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C144 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C150 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C151 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C153 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C157 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C158 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C159 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C160 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C161 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C162 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C167 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C168 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C173 3963610005 "CAP,F,STAN,16V,100UF,7343" C174 3963610005 "CAP,F,STAN,16V,100UF,7343" C176 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C177 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C178 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C179 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C180 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C181 3969800060 "CAP,F,CER,16V,.22UF,0603" C182 3969800061 "CAP,F,CER,10V,2.2UF,0603" C184 3961815001 "CAP,.015UF,25V,X7R,SMT,06" C185 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C186 3961200002 "CAP,3PF,100V,NP0,SMT,0603" C187 3962000004 "CAP,F,CER,50V,1000PF,0603" C188 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C189 3962000004 "CAP,F,CER,50V,1000PF,0603" C190 3961200002 "CAP,3PF,100V,NP0,SMT,0603" C192 3962822004 "CAP,STAN,22UF,16V,6032" C197 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C198 3960801009 "CAP,10PF,25V,NP0,SMT,0603" C199 3960802709 "CAP,27PF,25V,NPO,SMT,0603" C200 3960802709 "CAP,27PF,25V,NPO,SMT,0603" C201 3960802709 "CAP,27PF,25V,NPO,SMT,0603" C202 3962000005 "CAP,4700PF,50V,X7R,SMT,06" C209 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C210 3963610004 "CAP,10UF,16V,TANT,3528" C212 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C213 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C214 3962833003 "CAP,F,STAN,16V,3.3UF,3216" C215 3961833002 "CAP,X7R,25V,.33UF,1210" C216 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C219 3961833002 "CAP,X7R,25V,.33UF,1210" C220 3969800045 "CAP,X7R,.1UF,16V,10%,0603" C229 39698000…

Text truncated - open the document above for the full version.

Parts List/Tune Up Info

FIND_NO COMPONENT DESC 1 206M005100 "PWB, UAIS DISPLAY BOARD" 2 2369800335 "CONT,SKT,.025"" SQ. PIN" 4 2769800112 "WIRE,#26,STRD,GRN,600V" 5 0601100019 EPK 0151 PART A & B 6 2760200112 "WIRE,MAGNET,#32,CLASS130" C501 3969822009 "CAP,NPO,220PF,100V,10%" C502 3969822009 "CAP,NPO,220PF,100V,10%" C503 3969822009 "CAP,NPO,220PF,100V,10%" C504 3961810002 "CAP,F,CER,25V,.1UF,10%," C505 3961810002 "CAP,F,CER,25V,.1UF,10%," C506 3961810002 "CAP,F,CER,25V,.1UF,10%," C507 3969822009 "CAP,NPO,220PF,100V,10%" C508 3963610004 "CAP,10UF,16V,TANT,3528" C509 3963610004 "CAP,10UF,16V,TANT,3528" C510 3963610004 "CAP,10UF,16V,TANT,3528" D1 1379800151 "LED,BI-COLOR,RD/GRN" D501 1379800149 "IND,LED,GRN,SMT" D502 1379800149 "IND,LED,GRN,SMT" D503 1379800149 "IND,LED,GRN,SMT" D504 1379800149 "IND,LED,GRN,SMT" D505 1379800149 "IND,LED,GRN,SMT" D506 1379800149 "IND,LED,GRN,SMT" D507 1379800149 "IND,LED,GRN,SMT" D508 1379800149 "IND,LED,GRN,SMT" D509 0889800163 "DIO,SUPRSR,10V,SMT" F501 1209800107 "FUSE,PTC,100MA" J1 0639802111 "CONN,HDR,17C,.050""" J2 0639802110 "CONN,HDR,15C,.050""" J3 0639802110 "CONN,HDR,15C,.050""" J4 0639802134 "CONN,FPC,20C,SMT" L501 0559800264 "COIL,.18UH,SMT,1206" Q501 2631622220 "XSTR,NPN,SI,SINGLE,40VCE," Q502 2631622220 "XSTR,NPN,SI,SINGLE,40VCE," Q503 2631622220 "XSTR,NPN,SI,SINGLE,40VCE," Q504 2631600252 "XSTR,PNP,SI,60VCE,225MW," Q505 2631622220 "XSTR,NPN,SI,SINGLE,40VCE," R501 6912110001 "RES,F,TF,10K,1%,.1W,100" R502 6912110001 "RES,F,TF,10K,1%,.1W,100" R503 6912110001 "RES,F,TF,10K,1%,.1W,100" R504 0180002003 "POT,VOLUME,AUDIO TAPER" R505 6912113009 "RES,130 OHM,SMT" R506 6912110000 "RES,1K,SMT,0805" R507 6912113009 "RES,130 OHM,SMT" R508 6912110000 "RES,1K,SMT,0805" R509 6912113009 "RES,130 OHM,SMT" R510 6912118201 "RES,18.2K,SMT" R511 6912115009 "RES,150 OHM,SMT" R512 6912110000 "RES,1K,SMT,0805" R513 6912147500 "RES,4.75K,SMT,0805" R514 6912147500 "RES,4.75K,SMT,0805" R515 6912102219 "RES,22.1 OHM,SMT,0805" R516 6912147509 "RES,475 OHM,SMT,0805" U501 0469702858 "IC,3 TO 8 LINE DCDR,SMT" U502 0469702856 "IC,OP-AMP,QUAD,SMT" JP1 6923800001 "RES,JUMPER,1206,ZERO OHM," JP2 6923800001 "RES,JUMPER,1206,ZERO OHM," JP3 6923800001 "RES,JUMPER,1206,ZERO OHM," JP4 6923800001 "RES,JUMPER,1206,ZERO OHM," JP5 6923800001 "RES,JUMPER,1206,ZERO OHM," JP6 6923800001 "RES,JUMPER,1206,ZERO OHM,"

Parts List/Tune Up Info

FIND_NO COMPONENT DESC 1 206M027203 "PWB,AIS CPU DUAL PRCSSR" C1 3963610004 "CAP,10UF,16V,TANT,3528" C2 3963610004 "CAP,10UF,16V,TANT,3528" C3 3962010000 "CAP,F,CER,50V,1000PF,0805" C4 3961175000 "CAP,F,CERT,50V,7500PF,5%," C5 3962010000 "CAP,F,CER,50V,1000PF,0805" C6 3962010000 "CAP,F,CER,50V,1000PF,0805" C…

Text truncated - open the document above for the full version.