IR5RF10Notebook computer

NOTEBOOK COMPUTER RF10 User’s Guide (Preliminary Draft) I Notice The company reserves the right to revise this publication or to change its contents without any notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication. Any of the software described in this manual is sold or licensed "as is". Should the programs prove defective following purchase, the buyer (and not the manufacturer, its distributor, or its dealer) assumes the entire cost of all necessary servicing, repair and any incidental or consequential damages resulting from any software defects. Brand and product names mentioned in this publication may or may not be copyrights and/or registered trademarks of their respective companies. They are mentioned for identification purposes only and are not intended as an endorsement of that product or its manufacturer. Copyright © 2013 MilDef Crete Inc. Trademarks All other brand and product names are trademarks or registered trademarks of their respective companies. II Revision History: Revision Date Changes Author III FCC (Federal Communications Commission) Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and radiates radio frequency energy. If not being installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Re-orient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  This device may not cause harmful interference.  This device must accept any interference received, including interference that may cause undesired operation. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). IV Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Regulatory Information/ Disclaimers Installation and use of this computer must be in strict accordance with the instructions included in the user documentation provided with the product. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user’s authority to operate the equipment. The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of this device, or the substitution of the connecting cables and equipment other than manufacturer specified. It is the responsibility of the user to correct any interference caused by such unauthorized modification, substitution or attachment. Manufacturer and its authorized resellers or distributors will assume no liability for any damage or violation of government regulations arising from failing to comply with these guidelines. V CE Products with the CE Marking comply with both the EMC Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms: LVD EN 60950-1: 2006+ A11: 2009+ A1: 2010+ A12: 2011 IEC 60950-1: 2005+AM1:2009 R&TTE (CE) Manual Regulatory Requirement WLAN - IEEE 802.11a/b/g/n 802.11a/b/g/n Restrictions: European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2.400-2.4835 GHz. In France, the equipment must be restricted to the 2.4465-2.4835 GHz frequency range and must be restricted to indoor use. This device have been tested to comply with the Sound Pressure Level requirement laid down in the applicable EN 50332-1and/or EN 50332-2 standards. Permanent hearing loss may occur if earphones or headphones are used at high volume for prolonged periods of time. A pleine puissance, l’écoute prolongée du baladeur peut endommager l’oreille de l’utilisateur. To prevent possible hearing damage, do not listen at high volume levels for long periods. VI CE Declaration of Conformity It is confirmed to comply with the requirements set out in the Council Directive on the approximation of the laws of the member states relating to Electromagnetic Compatibility (2004/108/EC), Low-voltage Directive (2006/95/EC), the Amendment Directive (93/68/EEC), and the procedures given in European Council Directive (99/5/EC and 2004/108/EC ). The equipment was passed, and the equipment test was performed according to the following European standards: 1. Health …

Text truncated - open the document above for the full version.

7F, No. 250, Sec 3, Pei Shen Rd., Shen Keng District, New Taipei City, Taiwan Date: October 31, 2013 Power of Attorney To whom it may concern, Please be notified that I, Willie Liang of MilDef Crete Inc., have designated Daniel Lee of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan as the person being responsible for this project and to sign the form 731 and other documentation. Any and all acts carried out by Daniel Lee of Bureau Veritas Consumer Products Services (H.K .) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan on the matters relating to all processes required in the FCC approval and any communication needed with the national authority, shall have the same legal authority as acts on our own behalf. As defined in 47 CFR Ch. 1.2002 (b), we further certify that neither the applicant nor any party to this application is subject to a denial to Federal benefits, including FCC benefits, pursuant to section 5301 of the Anti-Drug Abuse Act of 1998, 21 U.S.C. 835(a). This authorization is limited to the product of as following: FCC ID: IR5RF10 If you have any acknowledgement and response, please send it to Daniel Lee of Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch (BV CPS Taoyuan Branch) of Taiwan directly. Should you have any question or comment regarding this matter, please have my best attention. Sincerely yours, Willie Liang / Manager MilDef Crete Inc. Fax: 886-2-2662-6079 Tel: 886-2-2662-6074 # 627 E-mail: [email protected]

7F, No. 250, Sec 3, Pei Shen Rd., Shen Keng District, New Taipei City, Taiwan Date: October 31, 2013 Federal Communications Commission 7345 Oakland Mills Road Columbia MD21046 Subject: Request for Confidentiality FCC ID: IR5RF10 To Whom It May Concern, Pursuant to the provisions of Sections 0.457 and 0.459 of Commission’s rules (47CFR§§0.457, 0.459), we are requesting the Commission to withhold the following attachments as confidential document from public disclosure indefinitely.  Schematic Diagram  Block Diagram  Operational Description Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Best Regards, Willie Liang / Manager MilDef Crete Inc. Fax: 886-2-2662-6079 Tel: 886-2-2662-6074 # 627 E-mail: [email protected]

7F, No. 250, Sec 3, Pei Shen Rd., Shen Keng District, New Taipei City, Taiwan Date: October 31, 2013 Federal Communications Commission Authorization and Evaluation Division 7345 Oakland Mills Road Columbia MD 21046 SUBJECT: FCC Application for FCC ID: IR5RF10 To Whom It May Concern, We, MilDef Crete Inc., hereby attest to the fact that we will apply the Declaration of Conformity procedure to the class B computer peripheral portion of this composite filing. Sincerely yours, Willie Liang / Manager MilDef Crete Inc. Fax: 886-2-2662-6079 Tel: 886-2-2662-6074 # 627 E-mail: [email protected]

7F, No. 250, Sec 3, Pei Shen Rd., Shen Keng District, New Taipei City, Taiwan Date: October 31, 2013 Declaration We, MilDef Crete Inc., declare that the device, FCC ID:IR5RF10, Model Name:RF10, does not support any non-US channels in all the operational mode(s) in North America. All non-US frequencies and Country code selection are disabled through proprietary software and is not user changeable. Should you have any question or comment regarding this matter, please do not hesitate to contact me. Sincerely yours, _____________________ Willie Liang / Manager MilDef Crete Inc. Fax: 886-2-2662-6079 Tel: 886-2-2662-6074 # 627 E-mail: [email protected]

7F, No. 250, Sec 3, Pei Shen Rd., Shen Keng District, New Taipei City, Taiwan Date: November 26, 2013 Declaration To whom it may concern, RF10 is a WLAN/Bluetooth combination antenna with FCC ID: IR5RF10. This WLAN/Bluetooth co-existence mechanism is to ensure that the WLAN and Bluetooth transmitters would not simultaneously operate. Therefore, WLAN and Bluetooth antenna in RF10 should not be considered to be able to transmit simultaneously. Though the users can use WLAN and Bluetooth simultaneously, but the real situation is that WLAN and Bluetooth are used by time sharing and no overlap transmission. Should you have any question, please have my best attention. Sincerely yours, _______________ Willie Liang / Manager MilDef Crete Inc. Fax: 886-2-2662-6079 Tel: 886-2-2662-6074 # 627 E-mail: [email protected]

Page 1 Report No.: 130918C09 CONSTRUCTION PHOTOS OF EUT 1. WLAN/BT Aux. Antenna 2. GPS Antenna 3. WLAN/BT Main Antenna 1 2 3 Page 2 Report No.: 130918C09 Page 3 Report No.: 130918C09 Page 33 Report No.: 130918C09 Page 34 Report No.: 130918C09 Page 35 Report No.: 130918C09 Page 36 Report No.: 130918C09

FCC ID: IR5RF10 Bottom of EUT Label Location

Page 4 Report No.: 130918C09 Module Page 5 Report No.: 130918C09 Page 6 Report No.: 130918C09 Page 7 Report No.: 130918C09 Page 8 Report No.: 130918C09 Page 9 Report No.: 130918C09 Page 10 Report No.: 130918C09 Page 11 Report No.: 130918C09 Page 12 Report No.: 130918C09 Page 13 Report No.: 130918C09 Page 14 Report No.: 130918C09 Page 15 Report No.: 130918C09 Page 16 Report No.: 130918C09 Page 17 Report No.: 130918C09

Page 18 Report No.: 130918C09 Page 19 Report No.: 130918C09 Page 20 Report No.: 130918C09 Page 21 Report No.: 130918C09 Page 22 Report No.: 130918C09 Page 23 Report No.: 130918C09 Page 24 Report No.: 130918C09 Page 25 Report No.: 130918C09 Page 26 Report No.: 130918C09 Page 27 Report No.: 130918C09 Page 28 Report No.: 130918C09 Page 29 Report No.: 130918C09 Page 30 Report No.: 130918C09 Page 31 Report No.: 130918C09 Page 32 Report No.: 130918C09

Report No.: SA130918C09 1 of 5 Report Format Version 5.1.0 RF EXPOSURE REPORT REPORT NO.: SA130918C09 MODEL NO.: RF10 FCC ID: IR5RF10 RECEIVED: Sep. 18, 2013 ISSUED: Nov. 14, 2013 APPLICANT: MilDef Crete Inc. ADDRESS: 7F, No. 250, Sec.3, Peishen Rd., Shenkeng District, New Taipei City, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: SA130918C09 2 of 5 Report Format Version 5.1.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ...........................................................................................3 1. CERTIFICATION ........................................................................................................4 2. RF EXPOSURE .........................................................................................................5 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................... 5 2.2 MPE calculation Formula ................................................................................. 5 2.3 Classification .................................................................................................... 5 2.4 calculation result of maximum conducted power .............................................. 5 Report No.: SA130918C09 3 of 5 Report Format Version 5.1.0 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED SA130918C09 Original release Nov. 14, 2013 Report No.: SA130918C09 4 of 5 Report Format Version 5.1.0 1. CERTIFICATION PRODUCT: Notebook computer MODEL NO.: RF10 BRAND: MilDef Crete Inc. APPLICANT: MilDef Crete Inc. TEST SAMPLE: Production Unit STANDARDS: FCC Part 2 (Section 2.1091) FCC OET Bulletin 65, Supplement C (01-01) IEEE C95.1 The above equipment (model: RF10) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY : , DATE : Nov. 14, 2013 Vera Huang / Specialist APPROVED BY : , DATE : Nov. 14, 2013 Roy Wu / Manager Report No.: SA130918C09 5 of 5 Report Format Version 5.1.0 2. RF EXPOSURE 2.1 LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) FREQUENCY RANGE (MHz) ELECTRIC FIELD STRENGTH (V/m) MAGNETIC FIELD STRENGTH (A/m) POWER DENSITY (mW/cm 2 ) AVERAGE TIME (minutes) LIMITS FOR GENERAL POPULATION / UNCONTROLLED EXPOSURE 300-1500 ... ... F/1500 30 1500-100,000 ... ... 1.0 30 F = Frequency in MHz 2.2 MPE CALCULATION FORMULA Pd = (Pout*G) / (4*pi*r 2 ) where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm 2.3 CLASSIFICATION The antenna of this product, under normal use condition, is at least 20cm away from the body of the user. So, this device is classified as Mobile Device. 2.4 CALCULATION RESULT OF MAXIMUM CONDUCTED POWER Frequency band (MHz) Conducted power (dBm) Antenna Gain (dBi) E.I.R.P. (mW) Power Density (mW/cm2) Limit (mW/cm2) Bluetooth 6.50 -1.12 3.45 0.0007 1.00 WLAN 2.4GHz 15.79 1.89 58.61 0.0117 1.00 5180~5240 16.99 3.33 107.65 0.0214 1.00 5745~5805 16.32 4.46 119.67 0.0238 1.00 Note: For WLAN 2.4GHz: Directional gain = -1.12dBi + 10log(2) = 1.89dBi

Report No.: RF130918C09 1 of 65 Report Format Version 5.0.0 FCC TEST REPORT (BLUETOOTH) REPORT NO.: RF130918C09 MODEL NO.: RF10 FCC ID: IR5RF10 RECEIVED: Sep. 18, 2013 TESTED: Oct. 03, 2013 ~ Oct. 23, 2013 ISSUED: Nov. 14, 2013 APPLICANT: MilDef Crete Inc. ADDRESS: 7F, No. 250, Sec.3, Peishen Rd., Shenkeng District, New Taipei City, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130918C09 2 of 65 Report Format Version 5.0.0 Table of Contents RELEASE CONTROL RECORD ........................................................................................ 6 1. CERTIFICATION ..................................................................................................... 7 2. SUMMARY OF TEST RESULTS ............................................................................. 8 2.1 MEASUREMENT UNCERTAINTY ................................................................................ 9 3. GENERAL INFORMATION ................................................................................... 10 3.1 GENERAL DESCRIPTION OF EUT ...................................................................... 10 3.2 DESCRIPTION OF TEST MODES........................................................................ 11 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL......................... 12 3.3 GENERAL DESCRIPTION OF APPLIED STANDARDS ....................................... 15 3.4 DESCRIPTION OF SUPPORT UNITS .................................................................. 16 3.4.1 CONFIGURATION OF SYSTEM UNDER TEST ................................................... 16 4. TEST TYPES AND RESULTS (FOR Bluetooth EDR) ............................................ 17 4.1 Radiated Emission AND BANDEDGE Measurement ............................................ 17 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT .............. 17 4.1.2 TEST INSTRUMENTS .......................................................................................... 18 4.1.3 TEST PROCEDURES .......................................................................................... 19 4.1.4 DEVIATION FROM TEST STANDARD ................................................................. 19 4.1.5 TEST SETUP ........................................................................................................ 20 4.1.6 EUT OPERATING CONDITIONS .......................................................................... 20 4.1.7 TEST RESULTS ................................................................................................... 21 4.2 CONDUCTED EMISSION MEASUREMENT ........................................................ 25 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ...................................... 25 4.2.2 TEST INSTRUMENTS .......................................................................................... 25 4.2.3 TEST PROCEDURES .......................................................................................... 26 4.2.4 DEVIATION FROM TEST STANDARD ................................................................. 26 4.2.5 TEST SETUP ........................................................................................................ 27 4.2.6 EUT OPERATING CONDITIONS .......................................................................... 27 4.2.7 TEST RESULTS ................................................................................................... 28 4.3 NUMBER OF HOPPING FREQUENCY USED ..................................................... 30 4.3.1 LIMIT OF HOPPING FREQUENCY USED ........................................................... 30 4.3.2 TEST SETUP ........................................................................................................ 30 4.3.3 TEST INSTRUMENTS .......................................................................................... 30 4.3.4 TEST PROCEDURES .......................................................................................... 30 4.3.5 DEVIATION FROM TEST STANDARD ................................................................. 30 4.3.6 TEST RESULTS ................................................................................................... 30 4.4 DWELL TIME ON EACH CHANNEL ..................................................................... 32 4.4.1 LIMIT OF DWELL TIME USED .…

Text truncated - open the document above for the full version.

Report No.: RF130918C09-1 1 of 71 Report Format Version 5.0.0 FCC TEST REPORT (15.247) REPORT NO.: RF130918C09-1 MODEL NO.: RF10 FCC ID: IR5RF10 RECEIVED: Sep. 18, 2013 TESTED: Oct. 03, 2013 ~ Oct. 23, 2013 ISSUED: Nov. 14, 2013 APPLICANT: MilDef Crete Inc. ADDRESS: 7F, No. 250, Sec.3, Peishen Rd., Shenkeng District, New Taipei City, Taiwan ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Tsuen, Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. Report No.: RF130918C09-1 2 of 71 Report Format Version 5.0.0 TABLE OF CONTENTS RELEASE CONTROL RECORD ............................................................................................ 5 1. CERTIFICATION ......................................................................................................... 6 2. SUMMARY OF TEST RESULTS ................................................................................. 7 2.1 MEASUREMENT UNCERTAINTY ................................................................... 7 3. GENERAL INFORMATION ......................................................................................... 8 3.1 GENERAL DESCRIPTION OF EUT ................................................................. 8 3.2 DESCRIPTION OF TEST MODES ................................................................... 9 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL .................. 10 3.3 DESCRIPTION OF SUPPORT UNITS ........................................................... 14 3.3.1 CONFIGURATION OF SYSTEM UNDER TEST ............................................ 14 3.4 GENERAL DESCRIPTION OF APPLIED STANDARDS ................................. 15 4. TEST TYPES AND RESULTS (FOR 2.4GHz BAND) ................................................ 16 4.1 RADIATED EMISSION AND BANDEDGE MEASUREMENT ......................... 16 4.1.1 LIMITS OF RADIATED EMISSION AND BANDEDGE MEASUREMENT ....... 16 4.1.2 TEST INSTRUMENTS ................................................................................... 17 4.1.3 TEST PROCEDURES .................................................................................... 18 4.1.4 DEVIATION FROM TEST STANDARD .......................................................... 18 4.1.5 TEST SETUP ................................................................................................. 19 4.1.6 EUT OPERATING CONDITIONS ................................................................... 19 4.1.7 TEST RESULTS ............................................................................................. 20 4.2 CONDUCTED EMISSION MEASUREMENT ................................................. 33 4.2.1 LIMITS OF CONDUCTED EMISSION MEASUREMENT ............................... 33 4.2.2 TEST INSTRUMENTS ................................................................................... 33 4.2.3 TEST PROCEDURES .................................................................................... 34 4.2.4 DEVIATION FROM TEST STANDARD .......................................................... 34 4.2.5 TEST SETUP ................................................................................................. 35 4.2.6 EUT OPERATING CONDITIONS ................................................................... 35 4.2.7 TEST RESULTS ............................................................................................. 36 4.3 6dB BANDWIDTH MEASUREMENT .............................................................. 38 4.3.1 LIMITS OF 6dB BANDWIDTH MEASUREMENT ........................................... 38 4.3.2 TEST SETUP ................................................................................................. 38 4.3.3 TEST INSTRUMENTS ................................................................................... 38 4.3.4 TEST PROCEDURE ...................................................................................... 38 4.3.5 DEVIATION FROM TEST STANDARD .......................................................... 38 4.3.6 EUT OPERATING CONDITIONS ................................................................... 38 4.3.7 TEST RESULTS ............................................................................................. 39 4.4 CONDUCTED OUTPUT POWER .................................................................. 40 4.4.1 LIMITS OF CONDUCTED OUTPUT POWER MEASUREMENT .................... 40 Report No.: RF130918C09-1 3 of 71 Report Format Ver…

Text truncated - open the document above for the full version.

Report No.: 130918C09 1 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: 130918C09 2 RADIATED EMISSION TEST (For Bluetooth & WLAN 2.4GHz & WLAN 5GHz)