IRJ-MT830Mini Wireless Barcode Scanner

2D Mini Wireless Barcode Scanner Quick Guide (Rev1) P/N: 8013-0072000 2D Mini Wireless Barcode Scanner Quick Guide For full user’s manual, please contact your local distributor. FCC WARNING STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirement, please follow operation instruction as documented in this manual. WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT The WEEE directive places an obligation on all EU-based manufacturers and importers to take- back electronic products at the end of their useful life. ROHS STATEMENT OF COMPLIANCE This product is compliant to Directive 2002/95/EC. NON-MODIFICATION STATEMENT Changes or modifications not expressly approved by the party responsible for compliance RoHS -1 - 1. Take any metals into contact with the terminals in connectors. 2. Use the scanner where any inflammable gases. If following condition occur, immediately power off the host computer, disconnect the interface cable, and contact your nearest dealer. 1. Smoke, abnormal odors or noises come from the scanner. 2. Drop the scanner so as to affect the operation or damage its housing. Do Not Do not do behavior below. 1. Put the scanner in places excessively high temperatures such as expose under direct sunlight. 2. Use the scanner in extremely humid area or drastic temperature changes. 3. Place the scanner in oily smoke or steam environment such as cooking range. 4. Be covered or wrapped up the scanner in bad-ventilated area such as under cloth or blanket. 5. Insert or drop foreign materials or water into scanning window or vents. 6. Using the scanner while hand is wet or damp. 7. Use the scanner with anti-slip gloves containing plasticizer and chemicals or organic solvents such as benzene, thinner, insecticide etc to clean the housing. Otherwise, it could not result fire and electrical shock but housing may be broken and injured. 8. Scratch or modify the scanner and bend, twist, pull or heat its interface cable. 9. Put heavy objects on interface cable. Do not stare the light source from the scanning window or do not point the scanning window at other people’s eyes or eyesight may be damaged by direct exposure under the light. Do not put the scanner on an unstable or inclined plane. The scanner may drop, creating injuries. Once the interface cable is damaged such as exposed or broken copper wires, stop using immediately and contact your dealer. Otherwise, it could result fire or electrical shock. WARNING AND CAUTION -2 - This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. OUT OF THE BOX 2D Mini Wireless Barcode Scanner USB Charger Cable Neck StrapRetractable Carabiner Badge Holder Reels -3 - INTRODUCTION SPECIFICATIONS Sensor Area Image Sensor Resolution 4mil/ 0.1mm (1D); 7mil/ 0.2mm (2D) PCS 30% Memory2MB IndicatorLED, Buzzer Housing Plastic (PC+ABS) Profile SPP, HID Battery Life 4260 scans Charge Time 2 hours (fully charged) Radio Bluetooth 2.1 + EDR Coverage 10M/33ft. (line of sight) Symbologies All major 1D & 2D barcodes -4 - LED Indicator Micro USB port Exit Window Trigger Button (w/ Protective Cover) (1) iOS Hotkey Button (2) Delete Button Silicone Cover Quick Guide & Quick Connection Card NUMERIC BARCODES 1 *1* 2 *2* 3 *3* 4 *4* 5 *5* Mini Wireless Barcode Reader Quick Guide CHARGING THE BATTERY 1. Flip open the micro USB port on the scanner. 2. Inse rt the micro USB connector into the port on the sc anner and USB A connector into a USB port on the host PC. - 5 -- 6 - BEEPER INDICATION LED INDICATION Single long beep Power up Single beep Good read Single short beep The scanner reads a Code39 of ASCII in configuration procedure Two beeps i. Wireless connection ii. The scanner successfully reads a configuration barcode Two short beeps Good read (Batch mode/Memory mode) Four beeps (Hi-Lo-Hi-Lo) Out of range/Poor connection Five beeps Low power Three beeps Wireless disconnection Three short beeps i. The scanner reads a barcodes while disconnected. ii. The scanner reads an unexpected barcode during configuration procedure. (scan [ABORT] to abort and start over) Several short beeps The scanner switches from one communication mode to another Off Flashing Green Green for 2 sec Flashing Red Solid Red Standby…

Text truncated - open the document above for the full version.

Marson Tec hno lo gy Co Lt d QA-FR-170-B 7/29/2014 FCC Authorization 2020-02-26 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern: We Marson Technology Co Ltd the undersigned, Hereby authorizes Bay Area Compliance Laboratories Corporation to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corporation on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Shaw Gu/Project Man ager shaw@marson .com .t w 9F, No.108-3, Mincyu an Rd., Sindian Dist., New Taipei City, 2314 1, Taiwan

Marson Tec hno lo gy Co Lt d QA-FR-171-A FCC Confidential Authorization 2020-02-26 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: IRJ-MT830 In accordance with Sections 0.457 and 0.459 of the Commission’s Rules, Marson Technology Co Ltd, hereby requests long-term confidential treatment of information accompanying this application as outlined below: Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely, Shaw Gu/Project Man ager shaw@marson .com .t w 9F, No.108-3, Mincyu an Rd., Sindian Dist., New Taipei City, 2314 1, Taiwan

Marson Tec hno lo gy Co Lt d QA-FR-227-A 11/05/2013 DECLARATION OF SIMILARITY 2020-02-26 To: FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Dear Sir or Madam: We M arso n Techno lo gy Co L td hereby declare that product: Mini Wireless Barcode Scanner, model(s): MT830M is/are electrically identical with the same electromagnetic emissions and electromagnetic compatibility characteristics as model: MT830 tested by BACL, the results of which are featured in BACL project: RLK191029002 and FCC ID: IRJ-MT830 All the hardware, PCB board, layout, software and RF electric circuit is the same, only model name different, and description of the differences between the tested model and those that are declared similar are as follows: MT830 and MT830 only difference color. Please contact me should there be need for any additional clarification or information. Best Regards, Shaw Gu/Proje ct Manager shaw@marson .com .t w 9F, No.108-3, Mincyu an Rd., Sindian Dist., New Taipei Cit y, 23141, Taiwan

Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Project No.: RLK191029002-00B Page 1 of 2 External Photographs Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Project No.: RLK191029002-00B Page 2 of 2

MT830 Label Location Bottom housing RoHS S/N:JBXXXXXX MT830 Mini Wireless Barcode Scanner FCC ID: IRJ-MT830 Made In Taiwan

Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Project No.: RLK191029002-00B Page 1 of 9 Internal Photographs Antenna Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Project No.: RLK191029002-00B Page 2 of 9 Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Project No.: RLK191029002-00B Page 3 of 9 Module (Chip) Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Project No.: RLK191029002-00B Page 4 of 9 Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Project No.: RLK191029002-00B Page 5 of 9 Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Project No.: RLK191029002-00B Page 6 of 9 Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Project No.: RLK191029002-00B Page 7 of 9 Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Project No.: RLK191029002-00B Page 8 of 9 Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Project No.: RLK191029002-00B Page 9 of 9 ***** END OF REPORT *****

FCC Part 15.247 TEST REPORT For Marson Technology Co Ltd 9F, No.108-3, Mincyuan Rd., Sindian Dist., New Taipei City, 23141, Taiwan FCC ID: IRJ-MT830 Report Type Original Report Product Name: Mini Wireless Barcode Scanner Model Name: MT830 Series Model Name: MT830M Report Number : RLK191029002-00B Report Date : 2020/02/12 Reviewed By : Zeus Chen Prepared By: Bay Area Compliance Laboratories Corp.(Linkou Laboratory) No. 6, Wende 2Rd., Guishan Dist., Taoyuan City 33382, Taiwan (R.O.C.) Tel: +886 (3)3961072; Fax: +886 (3) 3961027 www.bacl.com.tw Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Bay Area Compliance Laboratories Corp.(Linkou Laboratory) Report No.: RLK191029002-00B Page 2 of 49 Revision History Revision Report Number Issue Date Description 1.0 RLK191029002-00B 2020/02/12 Original Report Bay Area Compliance Laboratories Corp.(Linkou Laboratory) Report No.: RLK191029002-00B Page 3 of 49 TABLE OF CONTENTS 1 GENERAL INFORMATION ........................................................................................................................... 5 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .............................................................................. 5 1.2 OPERATION CONDITION OF EUT ................................................................................................................. 5 1.3 OBJECTIVE AND TEST METHODOLOGY ........................................................................................................... 6 1.4 MEASUREMENT UNCERTAINTY ................................................................................................................... 6 1.5 ENVIRONMENTAL CONDITIONS AND TEST DATE ............................................................................................... 6 1.6 TEST FACILITY ........................................................................................................................................ 6 2 SYSTEM TEST CONFIGURATION .................................................................................................................. 7 2.1 DESCRIPTION OF TEST CONFIGURATION ......................................................................................................... 7 2.2 SUPPORT EQUIPMENT LIST AND DETAILS ....................................................................................................... 7 2.3 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................. 8 3 SUMMARY OF TEST RESULTS ...................................................................................................................... 9 4 FCC §15.247(I), § 1.1307, § 2.1093 – RF EXPOSURE .................................................................................... 10 4.1 APPLICABLE STANDARD .......................................................................................................................... 10 4.2 RF EXPOSURE EVALUATION RESULT ........................................................................................................... 10 5 FCC §15.203 – ANTENNA REQUIREMENTS ................................................................................................. 11 5.1 APPLICABLE STANDARD .......................................................................................................................... 11 5.2 ANTENNA LIST AND DETAILS .................................................................................................................... 11 6 FCC §15.207 - AC LINE CONDUCTED EMISSIONS ........................................................................................ 12 6.1 APPLICABLE STANDARD .......................................................................................................................... 12 6.2 EUT SETUP AND TEST PROCEDURE ............................................................................................................ 12 6.3 TEST EQUIPMENT LIST AND DETAILS ........................................................................................................... 13 6.4 TEST DATA AND TEST PLOT ..................................................................................................................... 14 7 FCC §15.209, §15.205, §15.247(D) – SPURIOUS EMISSIONS ........................................................................ 15 7.1 APPLICABLE STANDARD .......................................................................................................................... 15 7.2 EUT SETUP AND TEST PROCEDURE ............................................................................................................ 17 7.3 TEST EQUIPMENT LIST AND DETAILS ........................................................................................................... 18 7.4 RADIATED EMISSION TEST PLOT AND DATA .................................................................................................. 19 8 FCC §15.247(A)(1) – 20 DB EMISSION BANDWIDTH ................................................................................... 28 8.1 APPLICABLE STANDARD .......................................................................................................................... 28 8.2 TEST PROCEDURE ................................................................................................................................. 28 8.3 TEST EQUIPMENT LIST AND DETAILS ........................................................................................................... 28 8.4 TEST RESULTS ...................................................................................................................................... 29 9 FCC §15.247(A)(1) – CHANNEL SEPARATION TEST .....................................…

Text truncated - open the document above for the full version.

Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Report No.: RLK191029002-00B Page 1 of 3 EUT Setup Photographs Conduction Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Report No.: RLK191029002-00B Page 2 of 3 Radiated Emission (Below 1 GHz) Bay Area Compliance Laboratories Corp. (Linkou Laboratory) Report No.: RLK191029002-00B Page 3 of 3 Radiated Emission (Above 1 GHz)