IXVTA3312-1RF Remote Control

FEDERAL COMMUNICATIONS COMMISSION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Shielded interface cables must be used in order to comply with emission limits. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.

FCC ID : IXVTA3312-1 FRONT S I DE OF E U T Num b er 1 REAR SI DE O F EU T Num b er 2 FCC ID : IXVTA3312-1

FCC ID Label Drawing FCC ID: IXVTA3312-1 The following statement will be placed in the User’s Manual. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC ID : IX VT A3312-1 FCC ID LOCA TIO N

FCC ID : IXVTA3312-1 N u m b e r 1 Mechanical Construction FCC ID : IXVTA3312-1 N u m b e r 2 Mechanical Construction FCC ID : IXVTA3312-1 N u m b e r 3 Fron t SI D E O F Main bo ard FCC ID : IXVTA3312-1 N u m b e r 4 RE AR SID E O F Main bo ard

FCC ID:IXVTA3312-1 Description TA3312-1/Transmitter is a highly integrated, low-cost RF transmitter, comblned with an AVR RISC microcontrollcr, it requlrea only a crystal, a single LiMnO 2 coin cell (CR2032), an inductor and a runed-loop antenna to implement a complete on-off keyed (OOK) wireless RF REMOTE CONTROLLer.

FCC TEST REPORT Report No. : F252403 SPORTON International Inc. TEL : 886-2-2696-2468 FAX : 886-2-2696-2255 FCC TEST REPORT for 47 CFR, Part 15, Subpart C Equipment : RF REMOTE CONTROL Model No. : TA3312-1 FCC ID : IXVTA3312-1 Filing Type : Certification Applicant : AutoMicro TECHNOLOGY INC. No. 6, Alley 8, Lane 214, Pao-Ping Road, Young-Ho City, Taipei Hsien, Taiwan, R.O.C. ‚ The test result refers exclusively to the test presented test model / sample. ‚ Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. ‚ Certificate or Test Report must not be used by the applicant to claim the product in this test report endorsement by NVLAP or any agency of U.S. government. SPORTON International Inc. 6F, No.106, Sec. 1, Hsin Tai Wu Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. FCC TEST REPORT Report No. : F252403 SPORTON International Inc. FCC ID : IXVTA3312-1 TEL : 886-2-2696-2468 Page No. : i FAX : 886-2-2696-2255 Issued Date : Jun. 4, 2002 Table of Contents History of this test report..................................................................................................................ii CERTIFICATE OF COMPLIANCE........................................................................................................................1 1. General Description of Equipment under Test.............................................................................................2 1.1. Applicant..........................................................................................................................................................................................2 1.2. Manufacturer ...................................................................................................................................................................................2 1.3. Basic Description of Equipment under Test ....................................................................................................................................2 1.4. Feature of Equipment under Test ...................................................................................................................................................2 2. Test Configuration of Equipment under Test ...............................................................................................3 2.1. Test Manner ....................................................................................................................................................................................3 2.2. Description of Test System .............................................................................................................................................................3 2.3. Connection Diagram of Test System ..............................................................................................................................................4 2.4. A plot shows the EUT meet the requirement of 15.231(c) ..............................................................................................................5 3. Test Software ...................................................................................................................................................6 4. General Information of Test............................................................................................................................7 4.1. Test Facility .....................................................................................................................................................................................7 4.2. Standard for Methods of Measurement...........................................................................................................................................7 4.3. Test in Compliance with ..................................................................................................................................................................7 4.4. Frequency Range Investigated .......................................................................................................................................................7 4.5. Test Distance ..................................................................................................................................................................................7 5. Test of Conducted Powerline .........................................................................................................................8 6. Test of Radiated Emission..............................................................................................................................9 6.1. Major Measuring Instruments..........................................................................................................................................................9 6.1.1. from 30MHz to 1GHz 9 6.1.2. from 1GHz to 4.33GHz 9 6.2. Test Procedures ............................................................................................................................................................................10 6.3. Typical Test Setup Layout of Radiated Emission..........................................................................................................................11 6.4. Test Result of Radiated Emission .................................................................................................................................................12 7. Antenna Factor & Cable Loss ......................................................................................................................14 8. EMI Suppression Component List ...............................................................................................................15 9. List of Measuring Equipments Used ...........................................................................................................16 10. Uncertainty of Test Site .................…

Text truncated - open the document above for the full version.

FCC TEST REPORT Report No. : F252403 1.1. Photographs of Radiated Emission Test Configuration z The photographs show the configuration that generates the maximum emission. FRONT VIEW REAR VIEW SPORTON International Inc. FCC ID : IXVTA3312-1 TEL : 886-2-2696-2468 Page No. : 1 of 1 FAX : 886-2-2696-2255 Issued : Sep, 11, 2002