
Text extracted from the exhibit documents filed with the FCC. Open a document above to read the original.
Power Plug Wired 10BaseT ADSL Interface (to ac module) interface (Telephone Line) BLOCK DIAGRAM, 3EC18883 ADSL WIRELESS MODEM Front Antenna Back Anten na Power Supply+3.3V+5.0V+12VGND 3.3V 9V 10 BaseT Hub IC WX1513 Wireless LAN Access Point BoardWV1513 10 pinConnectorInterface ETHA ICMicroprocessor SACHEM IC ADS L Li neDriver /Receiver Analog Front End WX1513 BLOCKDIAGRAM ANT SW WEPENGINE 2. 4 GHzLPF TX/RX SW M IXER SAW FILTER AGC CTL LNA TX/ RX SW PLL 2038-2098M Hz AM P M IXER AM P AMP AM P TX/RX SW MIXE R M IXER AM P MIXE R M IXER LO AM P PLL Q DAC TX DAC TX ADC Q ADC I ADCI DAC RF DAC RF ADC IF DAC DEM ODULATOR I/O M O DU LA TOR TX ALC HOST INTERFAC E CONTROL PRO CESSOR MEMORY ACCESS ARBITER GP SERIAL POR TS FLASH MEMORY RADIO CONTROL] POR TS RADIODATAINTERFACE SRA M M EM ORY CPU 44M H z XTAL OSC 2. 4G H z VCO 748M H z VCO U11 RF/ I F CONV U9 QUAD I F CONV U5 BASEBAND PRO CESSO R U3 CPU FL1 U6 XTAL OSC 374 MHz saw fi l t er FL3 LPF U10 ANT SW U14 RF VCO U13 I F VCO REG3.3V VSS REG3. 3V 5V AM P BPF FL4/ FL5 U12 PO W ER AMP U18U19 U4, U1 MEMORY U2 MEMORY RXI RXQ TXI TXQ DATA TX/ RX 2412- 2472 MHz 2. 4 GHzBPF FL6 BPF ETHERNET cont ro l 10 PIN connecyor i nt erface U250 J250
Power Plug Wired 10BaseT ADSL Interface (to ac module) interface (Telephone Line) BLOCK DIAGRAM, 3EC18883 ADSL WIRELESS MODEM Front Antenna Back Anten na Power Supply+3.3V+5.0V+12VGND 3.3V 9V 10 BaseT Hub IC WX1513 Wireless LAN Access Point BoardWV1513 10 pinConnectorInterface ETHA ICMicroprocessor SACHEM IC ADS L Li neDriver /Receiver Analog Front End WX1513 BLOCKDIAGRAM ANT SW WEPENGINE 2. 4 GHzLPF TX/RX SW M IXER SAW FILTER AGC CTL LNA TX/ RX SW PLL 2038-2098M Hz AM P M IXER AM P AMP AM P TX/RX SW MIXE R M IXER AM P MIXE R M IXER LO AM P PLL Q DAC TX DAC TX ADC Q ADC I ADCI DAC RF DAC RF ADC IF DAC DEM ODULATOR I/O M O DU LA TOR TX ALC HOST INTERFAC E CONTROL PRO CESSOR MEMORY ACCESS ARBITER GP SERIAL POR TS FLASH MEMORY RADIO CONTROL] POR TS RADIODATAINTERFACE SRA M M EM ORY CPU 44M H z XTAL OSC 2. 4G H z VCO 748M H z VCO U11 RF/ I F CONV U9 QUAD I F CONV U5 BASEBAND PRO CESSO R U3 CPU FL1 U6 XTAL OSC 374 MHz saw fi l t er FL3 LPF U10 ANT SW U14 RF VCO U13 I F VCO REG3.3V VSS REG3. 3V 5V AM P BPF FL4/ FL5 U12 PO W ER AMP U18U19 U4, U1 MEMORY U2 MEMORY RXI RXQ TXI TXQ DATA TX/ RX 2412- 2472 MHz 2. 4 GHzBPF FL6 BPF ETHERNET cont ro l 10 PIN connecyor i nt erface U250 J250
Page 1 of 1 http://gullfoss.../Grant_Form.hts?application_id=98610&mode=COPY&fcc_id=MXF-WX1505/9/2001 FEDERAL COMMUNICATIONS COMMISSION WASHINGTON, D.C. 20554 GRANT OF EQUIPMENT AUTHORIZATION Certification Attention: Mike Chen NOT TRANSFERABLE EQUIPMENT AUTHORIZATION is hereby issued to the named GRANTEE, and is VALID ONLY for the equipment identified hereon for use under the Commission's Rules and Regulations listed below. GemTek Technology Co Ltd No. 1, Jen Al Road Hsinchu Industrial Park, Hukuo Hsiang Hsinchu, Taipei Hsien, Taiwan Date of Grant: 09/29/2000 Application Dated: 08/30/2000 FCC IDENTIFIER MXF-WX1500 Name of Grantee GemTek Technology Co Ltd Equipment Class: Part 15 Spread Spectrum Transmitter Notes: Access Point Grant Notes FCC Rule Parts Frequency Range (MHZ) Output Watts Frequency Tolerance Emission Designator 15 2412 - 2462 0.022 Output Power is Peak Class A Digital Device Mail To: Alan Lane, Manager Advance Data Technology Corporation 13-1 Lane 19, Wen Shan 3rd., St., Kweishan Taoyuan Hsien, 333 Taiwan, R.O.C. EA98610
Alcatel 2912 Wake Forest Road Raleigh, N.C. 27609 July 2, 2001 American TCB 6731 Whittier Avenue Suite C110 McLean, VA 22101 Gentlemen, In our SpeedTouch Wireless ADSL modem, model number 3EC18883, we are purchasing the GEMTEK model WX-1513 radio module and antennas and incorporating them into the modem. The radio module comes with the two antennas attached and we do not modify the radio module or the antennas in any way. David L. Hollis Sr. Electrical Engineer XDSL Hardware Development
762 Park Avenue 919.554.0901Main Youngsville, NC 27596 919.556.2043 Fax www.flextronics.com 22 May, 2001 Mr. Bill Graff American TCB 6731 Whittier Avenue Suite C110 McLean, VA 22101 Tel: (703) 847-4700 Fax: (703) 847-6888 Mr. Graff: Mr. Dave Hollis, of Alcatel USA, has asked us to obtain a grant of authorization for their SpeedTouch Wireless Modem. The FCC ID they would like granted for this product is JF6-0101. This product contains a radio on a printed circuit board that has been granted an authorization under FCC ID: MXF-WX1500. This grant was for a similar product, called Access Point. The transmitter module has not been approved as a module. Alcatel is using the radio board and antennas from the Access Point product and is therefore electrically and mechanically identical. Since the transmitter was not approved as a module, radiated and conducted emissions measurements were performed for the Alcatel product and the results presented. Since the radio module is exactly the same, we believe that the original radio test data applies to this product and the emission measurements reflect the only differences. We would like to have authorization granted for the Alcatel product (FCC ID: JF6-0101). This would be the only FCC ID on the product. If you have any questions, comments, or concerns regarding this, please feel free to contact me. Thank you for your time and efforts in this matter. Thank you, Michael Cantwell, PE, NCE
Alcatel 2912 Wake Forest Road Raleigh, N.C. 27609 July 17, 2001 Request for Confidentiality American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Application FCC ID: JF6-0101 Please be advised that the following information is to be held confidential and behalf of ALCATEL: ??Schematic Diagram 3EC17752AAAA-ECZZA The application contains technical information which ALCATEL deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. David L. Hollis Sr. Electrical Engineer xDSL Hardware Development
Power Port Ethernet Port Telephone Port
Power Port Ethernet Port Telephone Port
1 1.1 LAST sample for FCC : Alcatel SPEED TOUCH 570 MODEL NUMBER: CPYYWWNNNNN AA013EC 18883DD ÑÑÑ ÑÑÑ US C R LISTED I.T.E.E168438 PART OF A SYSTEM THAT IS COVERED IN WHOLE OR IN 5,951,660.6,044,151.6,072,810.6,088,386.6,105,084 PART BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 5,636,253.5,633,817.5,657,355.5,903,612.5,867,528 PRL–US_3/4_WIREL_P_0/35 Alcatel SPEED TOUCH 570 0–ALUS–112233 XX Unique address Production Plant Required for the US markt (UL) SSID : Alcatel112233 FC C REN:<0.1Made in: Country Part 15: FCC ID.: JF6–0101 Part 68: FCC ID.: 6VUBEL–35680–DL–N This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions (1) this device may not cause harmful interference (2) this device must be accept any interference received, including interference that may cause undesired operation
1 1.1 LAST sample for FCC : Alcatel SPEED TOUCH 570 MODEL NUMBER: CPYYWWNNNNN AA013EC 18883DD ÑÑÑ ÑÑÑ US C R LISTED I.T.E.E168438 PART OF A SYSTEM THAT IS COVERED IN WHOLE OR IN 5,951,660.6,044,151.6,072,810.6,088,386.6,105,084 PART BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 5,636,253.5,633,817.5,657,355.5,903,612.5,867,528 PRL–US_3/4_WIREL_P_0/35 Alcatel SPEED TOUCH 570 0–ALUS–112233 XX Unique address Production Plant Required for the US markt (UL) SSID : Alcatel112233 FC C REN:<0.1Made in: Country Part 15: FCC ID.: JF6–0101 Part 68: FCC ID.: 6VUBEL–35680–DL–N This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions (1) this device may not cause harmful interference (2) this device must be accept any interference received, including interference that may cause undesired operation
RF89081018Page 82/85 FCC ID:MXF-WX1500 Issued Date: August 28, 2000 photo5 photo6 RF89081018Page 83/85 FCC ID:MXF-WX1500 Issued Date: August 28, 2000 photo7 photo8
Figure 1 – Photo of EUT (with cover removed) Radio Board Antennas
The EUT is an ADSL modem and wireless hub. It connects to the telephone network over a normal telephone line. It connects to the computer equipment through a wireless link. It uses Asynchronous Digital Subscriber Line (ADSL) technology to achieve high data rates over normal twisted pair telephone cable. The wireless link incorporates two diversity monopole antennas with the ground planes of the Printed Circuit Board acting as the grounding for the antenna. It is a desktop modem having a plastic case. It is powered by a modular power supply that plugs into a 120 vac wall socket and is supported by the wall socket. The modem communicates with up to 64 computers or computer equipment over a wireless link. It acts as a hub to provide wireless connectivity between all the computer equipment and to remote networks or internet providers over the telephone line. I/O cables are: For the telco side it has an RJ11 telephone connector and a cord to plug into a wall type telephone socket. At the computer equipment side, it has one RJ45 connector for an Ethernet 10 mHz 10BaseT two pair cable. These allow connection to one computer and is used mainly for setting up the modem features and properties.
f gll ))'#1 -2 ' !'2 !.%-(+2 (-#, 3 3 4 #!$ $ "!$ ! "#, ))'#1 )+(/#, ,# -2 ' (+&-#(' (' %-%, ")+(.- +#(+ -( .,#'! -" ")+(.- + -"#, ))'#1 + .%%2 (%%(0 %% 0+'#'!, ' #',-+.-#(', &+$ (' -" )+(.- "#, ")-+ (/+, -" (%%(0#'! -()#,: -2 ',-+.-#(', .+()' %+-#(' ( (' (+&#-2 #( +*.'2 '-+ +' --&'- 3 '#' %,, (-# 4 O H I IO Directive AppendixSafety and Agency Regulatory Notices 294/ 300 3C 17766 AAAA TCZZA d. 04 Unless expressly and unambiguously approved by Alcatel, you may not: disassemble, deĆcompile, reverse engineer, trace or otherwise analyse the equipment, its content, operation, or functionality, or otherwise attempt to derive source code (or the underlying ideas, algorithms, structure or organization) from the equipment or from any other information provided by Alcatel, except to the extent that this restriction is expressly prohibited by local law; copy, rent, loan, reĆsell, sublicense, or otherwise transfer or distribute the equipment to others; modify, adapt or create a derivative work of the equipment; remove from any copies of the equipment any product identification, copyright or other notices; disseminate performance information or analysis (including, without limitation, benchmarks) from any source relatin gto the equipment. Such acts not expressly approved by Alcatel will result in the loss of product warranty and will invalidate the users authority to operate this equipment. Climaticconditions nstallation Cleaning Waterandmoisture Powersupplyadapte r AppendixFSafety and Agency Regulatory Notices 295/ 300 3EC 17766 AAAA TCZZA Ed. 04 F.1SafetyInstructions TheSpeedTouchproduct equipment is intended for: InĆhouse stationary desktop use; the maximum ambient temperature may not exceed 40ºC (104ºF). It must not be mounted in a location exposed to direct or excessive solar and/or heat radiation. It must not be exposed to heat trap conditions and must not be subjected to water or condensation. It must be installed in a Pollution Degree 2 environment. This device must be installed so that a separation distance of at least 20 centimeters is maintained between the internal radiating antenna and the body of the user in order to meet FCC RF exposure guidelines. Unplug this product from the wall outlet before cleaning. Donot use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool. TheSpeedTouchproduct comes with a portable power supply adapter. Due to the special characteristics of the output of the classIIACadaptor, only use the models or equivalent listed in thepower adapter table in this Users Guide. Pwece Pwecdeci Oveladig Sevicig WieleRFaea ))e'di1FSafe-2 a'd ge'c2 Reg.%a-(+2 N(-ice, 6/ 300 3EC 1 TCZZ Ed. 04 The )(0e+i' g(f -hi, )+(d.c- &.,- adhe+e -( -he )(0e+ ,)ecifica-i(', i'dica-ed (' -he &a+$i' g%abe%,. If 2(. a+e i',.+e (f -he -2)e (f )(0e+ ,.))%2 -( 2(.+ h(&e, c(',.%- 2(.+ )+(d.c- dea%e+ (+ %(ca% )(0e+ c(&)a'2. The &ai', ,(c$e- (.-%e- &.,- be c%(,e -( -he e*.i)&e'- a'd ea,i%2 acce,,ib%e. TheSpeedTouch)+(d.c- e*.i)&e'- i, '(- i'-e'ded -( be c(''ec-ed -( a' ITĆ-2)e )(0e+ ,2,-e&. D( '(- a%%(0 a'2-hi' g-( +e,- (' -he )(0e+ c(+d. D( '(- %(ca-e -hi, )+(d.c- 0he+e -he c(+d 0i%% be ,.bjec- -( )e+,(', 0a%$i' g(' i-. D( '(- (/e+%(ad 0a%% (&ai',) (.-%e-, a'd e1-e',i(' c(+d, a, -hi, i'c+ea,e, -he +i,$ (f fi+e (+ e%ec-+ic ,h(c$. T( +ed.ce -he +i,$ (f e%ec-+ic ,h(c$, d( '(- di,a,,e&b%e -hi, )+(d.c-. N('e (f i-, i'-e+'a% )a+-, a+e .,e+Ć+e)%aceab%e; -he+ef(+e, -he+e i, '( +ea,(' -( acce,, -he i'-e+i(+. O)e'i' g(+ +e&(/i' g c(/e+, &a2 e1)(,e 2(. -( da'ge+(., /(%-age,. I'c(++ec- +ea,,e&b%2 c(.%d ca.,e e%ec-+ic ,h(c$ if -he a))%ia'ce i, ,.b,e*.e'-%2 .,ed. If ,e+/ice (+ +e)ai+ 0(+$ i, +e*.i+ed, -a$e i- -( a *.a%ified ,e+/ice dea%e+. The %('gĆ-e+& cha+ac-e+i,-ic, (+ -he )(,,ib%e )h2,i(%(gica% effec-, (f +adi( f+e*.e'c2 e%ec-+(&ag'e-ic fie%d, a,,(cia-ed 0i-h -hi, e*.i)&e'- ha/e '(- bee' e/a%.a-ed. Damagerequiring servic e Modem/Telephoneuse Modification s ppendixFSafety and gency Regulatory otices 7/ 300 3EC 1 TCZZ Ed. 04 Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power supply cord or plug is damaged or frayed. If liquid has been spilled into the product. If the product has been exposed to rain or water. If the product does not operate normally. If the product has been dropped or damaged in any way. If the product exhibits a distinct change in performance. void using a modem/telephone (other than a cordless type) during an electric storm. There is a slight risk of electric shock caused by lightning. Do not use the telephone to report a gas leak in the vicinity ofthe leak. If telephone service is required on the same line, a central splitter, or distributed filter(s) must be installed for optimal DSL performance. Depending on your DSL configuration and type of splitter/filters, installation must be carried out by qualified service personnel. Consult your telephone service company or DSL service provider for instructions. Changes or modifications not expressly approved by lcatel could invalidate the users authority to operate this equipment. OHI IO ECDelrtionof Conformity AppendixFSafety and Agency Regulatory Notices 298/ 300 3EC 17766 AAAA TCZZA Ed. 04 F.2EuropeanommunityDeclarationofonformity Products with themarking comply with both EMC and Low Voltage Directives issued by the Commission of the European Community. A copy of the European Community Declaration of …
Text truncated - open the document above for the full version.
RF Exposure Compliance 47 CFR 15.247(b)(4) states: “Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess of the commission's guidelines. See § 1.1307(b)(1) of this Chapter.” The EUT is considered a portable transmitter per 47 CFR 2.1093. The Maximum Permissible Exposure (MPE) estimates are as follows: Table 1 of 47 CFR 1.1310 defines the MPE for the general population as 1mW/cm 2 . The distance from the EUT’s transmitting antenna to the distance where the exposure level reaches the maximum permitted level is calculated using the general equation: 2 4R PG S ? ? where: S = power density P = power input to the antenna G = linear power gain relative to isotropic radiator R = distance to the center of the radiation of the antenna therefore: ???? ?? ??.59.05.1 /14 26.123.22 4 2 incm cmmW mW S PG R??? ?? The 1mW/cm 2 limit is reached at a distance of 1.5 cm (0.59 in.) or closer to the transmitting antenna. The antennas are located within a plastic enclosure that, under normal operating conditions, is located further than 1.5 cm from the operator.
Report Number: 0931ALC Page 1 of 27 EUT: SpeedTouch Wireless Modem Model: 3EC18883DD FCC ID: JF6-0101 33_EME/I 01/29/2001 Emissions Test Report EUT Name: SpeedTouch Wireless Modem EUT Model: 3EC18883DD FCC ID: JF6-0101 FCC Title 47, Part 15, Subpart B Prepared for: Dave Hollis Alcatel USA 2912 Wake Forest Road Raleigh, NC 27609 Tel: 919-850-5332 Fax: 919-850-6590 Prepared by: Flextronics Compliance Laboratories 762 Park Avenue Youngsville, NC 27596 Tel: (919) 554-0901 Fax: (919) 556-2043 http://www.flextronics.com/ Report/Issue Date: 18 May 2001 Report Number: 0931ALC Statement of Compliance Report Number: 0931ALC Page 2 of 27 EUT: SpeedTouch Wireless Modem Model: 3EC18883DD FCC ID: JF6-0101 33_EME/I 01/29/2001 Manufacturer: Alcatel USA 2912 Wake Forest Road Raleigh, NC 27609 919-850-5332 Requester / Applicant: Dave Hollis Name of Equipment: SpeedTouch Wireless Modem Model No. 3EC18883DD FCC ID: JF6-0101 Type of Equipment: Information Technology Equipment (ITE) Class of Equipment: Class B Application of Regulations: FCC Title 47, Part 15, Subpart B Test Dates: Start Date to End Date Guidance Documents: Emissions: FCC 47 CFR Part 15 Test Methods: Emissions: ANSI C63.4:1992 The electromagnetic compatibility test and documented data described in this report has been performed and recorded by Flextronics Compliance Laboratories, in accordance with the standards and procedures listed herein. As the responsible authorized agent of the EMC laboratory, I hereby declare that a sample of one, of the equipment described above, has been shown to be compliant with the EMC requirements of the stated regulations and standards based on these results. If any special accessories and/or modifications were required for compliance, they are listed in the Executive Summary of this report. This report must not be used to claim product endorsement by NVLAP or any agency of the U.S. Government. This report contains data that are not covered by NVLAP accreditation. This report shall not be reproduced except in full, without the written authorization of the laboratory. 18 May 2001 Michael Cantwell, PE, NCE Date Operations Manager NVLAP Signatory Table of Contents Report Number: 0931ALC Page 3 of 27 EUT: SpeedTouch Wireless Modem Model: 3EC18883DD FCC ID: JF6-0101 33_EME/I 01/29/2001 1 EXECUTIVE SUMMARY........................................................................................................4 1.1 SCOPE.................................................................................................................................4 1.2 PURPOSE.............................................................................................................................4 1.3 SUMMARY OF TEST RESULTS................................................................................................4 1.4 SUMMARY OF EVALUATION RESULTS....................................................................................4 1.5 SPECIAL ACCESSORIES.........................................................................................................4 1.6 EQUIPMENT MODIFICATIONS................................................................................................5 2 LABORATORY INFORMATION............................................................................................5 2.1 ACCREDITATIONS & ENDORSEMENTS....................................................................................5 2.2 TEST FACILITIES..................................................................................................................6 2.3 MEASUREMENT UNCERTAINTY.............................................................................................6 2.4 CALIBRATION TRACEABILITY...............................................................................................7 3 PRODUCT INFORMATION....................................................................................................7 3.1 PRODUCT DESCRIPTION........................................................................................................7 3.2 EQUIPMENT CONFIGURATION...............................................................................................8 3.3 OPERATION MODE...............................................................................................................8 4 EMISSIONS..............................................................................................................................8 4.1 RADIATED EMISSIONS..........................................................................................................8 4.2 CONDUCTED EMISSIONS.....................................................................................................16 5 TEST EQUIPMENT USE LIST..............................................................................................21 6 EMC TEST PLAN..................................................................................................................23 6.1 INTRODUCTION..................................................................................................................23 6.2 CUSTOMER........................................................................................................................23 6.3 EQUIPMENT UNDER TEST (EUT).........................................................................................23 6.4 EQUIVALENT MODELS........................................................................................................27 Flextronics Compliance Laboratories Scope 762 Park Ave., Youngsville, NC 27596 Tel: (919) 554-0901, Fax: (919) 556-2043 Report Number: 0931ALC Page 4 of 27 EUT: SpeedTouch Wireless Modem Model: 3EC18883DD FCC ID: JF6-0101 33_EME/I 01/29/2001 1 Executive Summary 1.1 Scope This report is intended to document the status of conformance with the requirements of the FCC Title 47, Part 15, Subpart B based on the results of testing performed on Start Date through End Date on the SpeedTouch Wireless Modem Model…
Text truncated - open the document above for the full version.
RF89081018Page 1/85 FCC ID:MXF-WX1500 Issued Date: August 28, 2000 REPORT NO:RF89081018 PRODUCT:Access Point MODEL NO:WX1500, WX1520 BRAND NAME:GemTek SERIAL NO:N/A CLIENT:GemTek Technology Co., Ltd. ADDRESS:No.1, Jen Ai Rd., Hsin Chu Industrial Park, Hu Kou, Hsin Chu 303, Taiwan R.O.C. ISSUED BY:ADVANCE DATA TECHNOLOGY CORPORATION (ADT CORP.) OFFICE ADDRESS:11F, NO. 1, SEC. 4, NAN-KING EAST RD., TAIPEI, TAIWAN, R.O.C. LABORATORY ADDRESS :NO. 47, 14 LING, CHIA PAU TSUEN, LIN KOU HSIANG, TAIPEI HSIEN, TAIWAN, R.O.C. TEST STANDARD:47CFR Part 15, Subpart C (15.247) & Subpart B TEST DATE:August 16, 2000 TEST RESULT:Pass This test report consists of 85 pages in total. This test report is the property of ADT Corp. and shall not be reproduced except in full, without the written consent of ADT. ADT hereby returns all rights in data to the client for legal use by the client. The test results contained in this report apply only to the samples tested. Accredited Laboratory RF89081018Page 2/85 FCC ID:MXF-WX1500 Issued Date: August 28, 2000 TABLE OF CONTENTS 1CERTIFICATION ......................................................................................................4 2SUMMARY OF TEST RESULTS & GENERAL STATEMENT OF CERTIFICATION 5 3DECLARATION OF COMPLIANCE WITH SUBPART B ..........................................6 4GENERAL INFORMATION ......................................................................................7 4.1G ENERAL D ESCRIPTION OF EUT ........................................................................................................... 7 4.2D ESCRIPTION OF T EST MODE ................................................................................................................. 8 4.3T EST M ETHODOLOGY ............................................................................................................................ 8 4.4S UPPORT U NITS L IST ............................................................................................................................. 9 4.5C ONFIGURATION OF S YSTEM U NDER T EST ............................................................................................ 9 5GENERAL INFORMATION OF TEST FACILITY....................................................10 5.1T EST L AB .: .......................................................................................................................................... 10 5.2C ALIBRATION I NTERVAL : .................................................................................................................... 10 6TEST PROCEDURES AND TEST RESULTS........................................................ 11 6.1C ONDUCTED E MISSION M EASUREMENT .............................................................................................. 11 6.1.1Test Instruments .................................................................................................................... 11 6.1.2Test Procedure ...................................................................................................................... 11 6.1.3 Test Setup............................................................................................................................... 12 6.1.4Photograph of Test Setup...................................................................................................... 13 6.1.5EUT Operating condition ..................................................................................................... 14 6.1.6Climate Condition ................................................................................................................ 14 6.1.7Test Results ........................................................................................................................... 15 6.26 D B B ANDWIDTH M EASUREMENT ...................................................................................................... 24 6.2.1Test Instruments .................................................................................................................... 24 6.2.2Test Procedure ...................................................................................................................... 24 6.2.3Test Setup .............................................................................................................................. 24 6.2.4EUT Operating Condition ....................................................................................................24 6.2.5Climate Condition ................................................................................................................ 25 6.2.6Test Results ........................................................................................................................... 25 6.3M AXIMUM P EAK P OWER O UTPUT AND RF E XPOSURE L IMIT M EASUREMENT .................................... 29 6.3.1Test Instruments .................................................................................................................... 29 6.3.2Test Procedure ...................................................................................................................... 29 RF89081018Page 3/85 FCC ID:MXF-WX1500 Issued Date: August 28, 2000 6.3.3RF exposure limit.................................................................................................................. 29 6.3.4 Test Setup............................................................................................................................... 31 6.3.5EUT Operating Condition ....................................................................................................31 6.3.6Climate Condition ................................................................................................................ 31 6.3.7Test Result............................................................................................................................. 32 6.4R ADIATED E MISSION M EASUREMENT .....................................…
Text truncated - open the document above for the full version.
RF89081018Page 80/85 FCC ID:MXF-WX1500 Issued Date: August 28, 2000 8 EUT PHOTOS photo1 photo2 RF89081018Page 81/85 FCC ID:MXF-WX1500 Issued Date: August 28, 2000 photo3 photo4 RF89081018Page 82/85 FCC ID:MXF-WX1500 Issued Date: August 28, 2000 photo5 photo6 RF89081018Page 83/85 FCC ID:MXF-WX1500 Issued Date: August 28, 2000 photo7 photo8 RF89081018Page 84/85 FCC ID:MXF-WX1500 Issued Date: August 28, 2000 photo9 photo10 RF89081018Page 85/85 FCC ID:MXF-WX1500 Issued Date: August 28, 2000 photo11 photo12
Report Number: 0931ALC Page 1 of 27 EUT: SpeedTouch Wireless Modem Model: 3EC18883DD FCC ID: JF6-0101 33_EME/I 01/29/2001 Emissions Test Report EUT Name: SpeedTouch Wireless Modem EUT Model: 3EC18883DD FCC ID: JF6-0101 FCC Title 47, Part 15, Subpart B Prepared for: Dave Hollis Alcatel USA 2912 Wake Forest Road Raleigh, NC 27609 Tel: 919-850-5332 Fax: 919-850-6590 Prepared by: Flextronics Compliance Laboratories 762 Park Avenue Youngsville, NC 27596 Tel: (919) 554-0901 Fax: (919) 556-2043 http://www.flextronics.com/ Report/Issue Date: 18 May 2001 Report Number: 0931ALC Statement of Compliance Report Number: 0931ALC Page 2 of 27 EUT: SpeedTouch Wireless Modem Model: 3EC18883DD FCC ID: JF6-0101 33_EME/I 01/29/2001 Manufacturer: Alcatel USA 2912 Wake Forest Road Raleigh, NC 27609 919-850-5332 Requester / Applicant: Dave Hollis Name of Equipment: SpeedTouch Wireless Modem Model No. 3EC18883DD FCC ID: JF6-0101 Type of Equipment: Information Technology Equipment (ITE) Class of Equipment: Class B Application of Regulations: FCC Title 47, Part 15, Subpa…
Text truncated - open the document above for the full version.
2912 Wake Forest Rd. · Raleigh, North Carolina · United States
| # | Rule Parts | Frequency Range | Power Output |
|---|---|---|---|
| 1 | 15C | 2.41 GHz - 2.46 GHz | 22.00 mW |

5 GHz rack-mounted point to point transceiver
Equipment Class
DTS - Digital Transmission System
5 GHz rack-mounted point to point transceiver
Equipment Class
DTS - Digital Transmission System
Microwave Packet Radio
Equipment Class
DTS - Digital Transmission System
MDR-8000
Equipment Class
TNB - Licensed Non-Broadcast Station Transmitter
MPT-HL Packet Terminal
Equipment Class
DTS - Digital Transmission System