JUP-59645900 Mhz Radio-Modem for Construction

Aqua User Manual Draft April 26, 2007 Aqua User Manual..................................................................... 1 1 Introduction.................................................................................................................... 3 Welcome .........................................................................................................................3 Related Information ........................................................................................................ 3 Technical Assistance....................................................................................................... 3 Your Comments .............................................................................................................. 3 2 Getting Started.............................................................................................................. 3 Introduction..................................................................................................................... 3 Hardware Specification................................................................................................... 4 AQUA Description ......................................................................................................... 4 Features ........................................................................................................................... 5 Frequency Band .............................................................................................................. 5 3 Configuring the AQUA.................................................................................................. 6 Introduction..................................................................................................................... 6 Default Settings..............................................................Error! Bookmark not defined. WinFlash Configuration Software .................................................................................. 7 Connecting to the AQUA................................................................................................ 7 Configuring the AQUA................................................................................................... 7 Network..........................................................................Error! Bookmark not defined. Mode ..............................................................................Error! Bookmark not defined. Serial Port Baud Rate and Parity ...................................Error! Bookmark not defined. Defaults ..........................................................................Error! Bookmark not defined. Diagnostics and Firmware Upgrade................................................................................ 9 Installing the AQUA.......................................................................................................... 9 Introduction..................................................................................................................... 9 Physical Description ....................................................................................................... 9 Connectors and Indicators............................................................................................... 9 Mounting the AQUA on a Machine.............................................................................. 10 Machine Mount Kit (PN 35087-00).............................................................................. 10 Machine Mounting........................................................................................................ 10 Cabling Configurations ................................................................................................. 11 Power and I/O Cable for Machine Installations............................................................ 11 Machine Service Cable ................................................................................................. 11 Antenna Description ..................................................................................................... 11 Antenna Considerations ................................................................................................ 12 A Technical Specifications............................................................................................ 12 Technical Information................................................................................................... 12 Pinout Information ........................................................................................................ 13 Glossary ............................................................................................................................ 14 Index................................................................................................................................. 14 1 Introduction Welcome This manual describes how to set up and use an Aqua radio modem. This publication assumes that you are know how to use the Microsoft® Windows® operating system. Related Information Sources of related information include the following: Readme.txt file – a Readme.txt file contains information added after the documentation was completed. To read this file, double-click it or use a text editor to open it. The installation program also copies it into the program directory. Release notes – the release notes describe new features of the product, information not included in the manuals, and any changes to the manuals. Update notes – there is a warranty activation sheet with this product. Send it in to automatically receive update notes containing important information about software and hardware changes. Contact your local dealer for more information about the support agreement contracts for software and firmware, and an extended warranty program for hardware. Technical Assistance If you have a problem and cannot find the information you need in …

Text truncated - open the document above for the full version.

Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 48 of 55 FCC Part 15.247 Report 16 EXHIBIT C - EUT EXTERNAL PHOTOGRAPHS 16.1 EUT External Top View 16.2 EUT with Reverse Antenna Port View Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 49 of 55 FCC Part 15.247 Report 16.3 EUT with Power & Data Port View 16.4 EUT Back View 1 Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 50 of 55 FCC Part 15.247 Report 16.5 Antenna View (Model: Antenna Mobile) 16.6 Antenna View (Model: SPDA17918)

Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 44 of 55 FCC Part 15.247 Report 14 EXHIBIT A - FCC ID LABEL INFORMATION 14.1 FCC § 2.925 Identification of equipment (a) Each equipment covered in an application for equipment authorization shall bear a nameplate or label listing the following: (1) FCC Identifier consisting of the two elements in the exact order specified in §2.926. The FCC Identifier shall be preceded by the term FCC ID in capital letters on a single line, and shall be of a type size large enough to be legible without the aid of magnification. Example: FCC ID XXX123. XXX—Grantee Code 123—Equipment Product Code 14.2 FCC ID Labeling Requirements as per FCC § 15.19 (a) In addition to the requirements in part 2 of this chapter, a device subject to certification, or verification shall be labeled as follows: (3) All other devices shall bear the following statement in a conspicuous location on the device: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (4) Where a device is constructed in two or more sections connected by wires and marketed together, the statement specified above is required to be affixed only to the main control unit. If the EUT is integrated within another device then a label affixed to the host shall also state, “Contains FCC ID:XXXXXX” (5) When the device is so small or for such use that it is not practicale to place the statement specified under paragraph (a) of this section on it, the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC identifier or the unique identifier, as appropriate, must be displayed on the device. 14.3 Suggested FCC ID Label Model: Aqua 900 MHz This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: JUP-59645 IC: 1756A-59645 Trimble Navigation Ltd. Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 45 of 55 FCC Part 15.247 Report 14.4 Suggested Label Position

Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 44 of 55 FCC Part 15.247 Report 14 EXHIBIT A - FCC ID LABEL INFORMATION 14.1 FCC § 2.925 Identification of equipment (a) Each equipment covered in an application for equipment authorization shall bear a nameplate or label listing the following: (1) FCC Identifier consisting of the two elements in the exact order specified in §2.926. The FCC Identifier shall be preceded by the term FCC ID in capital letters on a single line, and shall be of a type size large enough to be legible without the aid of magnification. Example: FCC ID XXX123. XXX—Grantee Code 123—Equipment Product Code 14.2 FCC ID Labeling Requirements as per FCC § 15.19 (a) In addition to the requirements in part 2 of this chapter, a device subject to certification, or verification shall be labeled as follows: (3) All other devices shall bear the following statement in a conspicuous location on the device: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (4) Where a device is constructed in two or more sections connected by wires and marketed together, the statement specified above is required to be affixed only to the main control unit. If the EUT is integrated within another device then a label affixed to the host shall also state, “Contains FCC ID:XXXXXX” (5) When the device is so small or for such use that it is not practicale to place the statement specified under paragraph (a) of this section on it, the information required by this paragraph shall be placed in a prominent location in the instruction manual or pamphlet supplied to the user or, alternatively, shall be placed on the container in which the device is marketed. However, the FCC identifier or the unique identifier, as appropriate, must be displayed on the device. 14.3 Suggested FCC ID Label Model: SNR910 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: JUP-59645 IC: 1756A-59645 Trimble Model: CR900 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: JUP-59645 IC: 1756A-59645 Caterpillar Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 45 of 55 FCC Part 15.247 Report 14.4 Suggested Label Position

Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 51 of 55 FCC Part 15.247 Report 17 EXHIBIT C - EUT INTERNAL PHOTOGRAPHS 17.1 EUT Cover off View 1 17.2 EUT with Cover off view 2 Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 52 of 55 FCC Part 15.247 Report 17.3 Control Board 1 - Front View 17.4 Control Board 1 - Back View Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 53 of 55 FCC Part 15.247 Report 17.5 Rx Front End, Transmitter and PLL Synthesizer – Side View of Radio Borad 17.6 2nd LO, 2nd IF and Connection Interface – Side View of Radio Board Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 54 of 55 FCC Part 15.247 Report 17.7 RF Board with Shield on - Front 17.8 RF Board with Shield off - Front Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 55 of 55 FCC Part 15.247 Report 17.9 RF Board – Back View

Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 42 of 44 FCC Part 15.247 Report 13 § 15.247 (i) and § 2.1091 - RF EXPOSURE 13.1 Applicable Standard According to §15.247(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to §1.1310 and §2.1091 RF exposure is calculated. Limits for General Population/Uncontrolled Exposure Limits for General Population/Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Averaging Time (minutes) 0.3-1.34 614 1.63 *(100) 30 1.34-30 824/f 2.19/f *(180/f 2 ) 30 30-300 27.5 0.073 0.2 30 300-1500 / / f/1500 30 1500-100,000 / / 1.0 30 f = frequency in MHz * = Plane-wave equivalent power density 13.2 MPE Prediction Predication of MPE limit at a given distance Equation from page 18 of OET Bulletin 65, Edition 97-01 S = PG/4πR² Where: S = power density P = power input to antenna G = power gain of the antenna in the direction of interest relative to an isotropic radiator R = distance to the center of radiation of the antenna Antenna Model: Antenna Mobile Test Data Maximum peak output power at antenna input terminal: 29.93(dBm ) Maximum peak output power at antenna input terminal: 984.01 (mw) Prediction distance: 20 (cm) Predication frequenc0y: 902.625(MHz) Antenna Gain (typical): 2 (dBi) Antenna gain: 1.58 (numeric) Power density at predication frequency at 20 cm: 0.3093(mW/cm 2 ) MPE limit for uncontrolled exposure at prediction frequency: 0.6(mW/cm 2 ) Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 43 of 44 FCC Part 15.247 Report Antenna Model: SPDA17918Test Data Maximum peak output power at antenna input terminal: 29.93(dBm ) Maximum peak output power at antenna input terminal: 984.01 (mw) Prediction distance: 20 (cm) Predication frequency: 902.625(MHz) Antenna Gain (typical): 2.14 (dBi) Antenna gain: 1.64 (numeric) Power density at predication frequency at 20 cm: 0.3210 (mW/cm 2 ) MPE limit for uncontrolled exposure at prediction frequency: 0.6(mW/cm 2 ) 13.3 Test Result The power density level at 20 cm is 0.3093 mW/cm² and 0.3210 mW/cm², which is below the uncontrolled exposure limit of 0.6 mW/cm² at 902.625 MHz. The EUT is used at least 20cm away from user’s body. It is determined as mobile equipment.

Note: This test report is for the customer shown above and their specific product only. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. FCC PART 15.247 EMI MEASUREMENT AND TEST REPORT For Trimble Navigation Ltd. 935 Stewart Drive Sunnyvale, CA 94085, USA FCCID: JUP-59645 Model: Aqua 900 MHz This Report Concerns: Original Report Product Type: 900 MHz radio modem Test Engineer(s): James Ma Dan Coronia Report Number: R0703211-247 Report Date: 2007-03-29 Reviewed By: VP of Engineering: Hans Mellberg Prepared By: (ct) Bay Area Compliance Laboratories Corp. 1274 Anvilwood Ave. Sunnyvale, CA 94089, USA Tel: (408) 732-9162 Fax: (408) 732-9164 Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 2 of 40 FCC Part 15.247 Report TABLE OF CONTENTS 1 GENERAL INFORMATION ..............................................................................................................................4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .......................................................................4 1.2 ANTENNA DESCRIPTION..................................................................................................................................4 1.3 MECHANICAL DESCRIPTION OF EUT ..............................................................................................................5 1.4 EUT PHOTOGRAPH.........................................................................................................................................5 1.5 OBJECTIVE......................................................................................................................................................5 1.6 RELATED SUBMITTAL(S)/GRANT(S)................................................................................................................5 1.7 TEST METHODOLOGY.....................................................................................................................................5 1.8 MEASUREMENT UNCERTAINTY.......................................................................................................................6 1.9 TEST FACILITY................................................................................................................................................6 2 SYSTEM TEST CONFIGURATION .................................................................................................................7 2.1 JUSTIFICATION................................................................................................................................................7 2.2 EUT EXERCISE SOFTWARE.............................................................................................................................7 2.3 SPECIAL ACCESSORIES....................................................................................................................................7 2.4 EQUIPMENT MODIFICATIONS..........................................................................................................................7 2.5 LOCAL SUPPORT EQUIPMENT..........................................................................................................................7 2.6 POWER SUPPLY LINES.....................................................................................................................................7 2.7 INTERNAL CONFIGURATION............................................................................................................................7 2.8 INTERFACE PORTS AND CABLING....................................................................................................................8 2.9 TEST SETUP BLOCK DIAGRAMS......................................................................................................................8 3 SUMMARY OF TEST RESULTS FOR FCC PART 15 ...................................................................................9 4 §15.203 - ANTENNA REQUIREMENT ...........................................................................................................10 4.1 APPLICABLE STANDARD...............................................................................................................................10 4.2 RESULT.........................................................................................................................................................10 5 §15.205, §15.209(A) & §15.247(D) - RADIATED EMISSIONS......................................................................11 5.1 APPLICABLE STANDARD: FCC §15.205 (A) ..................................................................................................11 5.2 APPLICABLE STANDARD: FCC §15.209 RADIATED EMISSION LIMITS, GENERAL REQUIREMENTS..................11 5.3 APPLICABLE STANDARD: FCC §15.247 (D) RADIATED SPURIOUS EMISSION REQUIREMENTS........................12 5.4 TEST SETUP..................................................................................................................................................12 5.5 TEST EQUIPMENT LIST AND DETAILS............................................................................................................12 5.6 ENVIRONMENTAL CONDITIONS.....................................................................................................................13 5.7 TEST PROCEDURE.........................................................................................................................................13 5.8 CORRECTED AMPLITUDE & MARGIN CALCULATION....................................................................................13 5.9 SUMMARY OF TEST RESULTS........................................................................................................................13 5.10 RADIAT…

Text truncated - open the document above for the full version.

Note: This test report is for the customer shown above and their specific product only. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. This report must not be used by the customer to claim product certification, approval, or endorsement by NVLAP, NIST, or any agency of the Federal Government. FCC PART 15.247 EMI MEASUREMENT AND TEST REPORT For Trimble Navigation Ltd. 935 Stewart Drive Sunnyvale, CA 94085, USA FCCID: JUP-59645 Model: CR900, SNR910 This Report Concerns: Original Report Product Type: 900 MHz radio modem Test Engineer(s): James Ma Dan Coronia Report Number: R0703211-247 Report Date: 2007-03-29 Reviewed By: VP of Engineering: Hans Mellberg Prepared By: (ct) Bay Area Compliance Laboratories Corp. 1274 Anvilwood Ave. Sunnyvale, CA 94089, USA Tel: (408) 732-9162 Fax: (408) 732-9164 Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 2 of 40 FCC Part 15.247 Report TABLE OF CONTENTS 1 GENERAL INFORMATION ..............................................................................................................................4 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .......................................................................4 1.2 ANTENNA DESCRIPTION..................................................................................................................................4 1.3 MECHANICAL DESCRIPTION OF EUT ..............................................................................................................5 1.4 EUT PHOTOGRAPH.........................................................................................................................................5 1.5 OBJECTIVE......................................................................................................................................................5 1.6 RELATED SUBMITTAL(S)/GRANT(S)................................................................................................................5 1.7 TEST METHODOLOGY.....................................................................................................................................5 1.8 MEASUREMENT UNCERTAINTY.......................................................................................................................6 1.9 TEST FACILITY................................................................................................................................................6 2 SYSTEM TEST CONFIGURATION .................................................................................................................7 2.1 JUSTIFICATION................................................................................................................................................7 2.2 EUT EXERCISE SOFTWARE.............................................................................................................................7 2.3 SPECIAL ACCESSORIES....................................................................................................................................7 2.4 EQUIPMENT MODIFICATIONS..........................................................................................................................7 2.5 LOCAL SUPPORT EQUIPMENT..........................................................................................................................7 2.6 POWER SUPPLY LINES.....................................................................................................................................7 2.7 INTERNAL CONFIGURATION............................................................................................................................7 2.8 INTERFACE PORTS AND CABLING....................................................................................................................8 2.9 TEST SETUP BLOCK DIAGRAMS......................................................................................................................8 3 SUMMARY OF TEST RESULTS FOR FCC PART 15 ...................................................................................9 4 §15.203 - ANTENNA REQUIREMENT ...........................................................................................................10 4.1 APPLICABLE STANDARD...............................................................................................................................10 4.2 RESULT.........................................................................................................................................................10 5 §15.205, §15.209(A) & §15.247(D) - RADIATED EMISSIONS......................................................................11 5.1 APPLICABLE STANDARD: FCC §15.205 (A) ..................................................................................................11 5.2 APPLICABLE STANDARD: FCC §15.209 RADIATED EMISSION LIMITS, GENERAL REQUIREMENTS..................11 5.3 APPLICABLE STANDARD: FCC §15.247 (D) RADIATED SPURIOUS EMISSION REQUIREMENTS........................12 5.4 TEST SETUP..................................................................................................................................................12 5.5 TEST EQUIPMENT LIST AND DETAILS............................................................................................................12 5.6 ENVIRONMENTAL CONDITIONS.....................................................................................................................13 5.7 TEST PROCEDURE.........................................................................................................................................13 5.8 CORRECTED AMPLITUDE & MARGIN CALCULATION....................................................................................13 5.9 SUMMARY OF TEST RESULTS........................................................................................................................13 5.10 RADIA…

Text truncated - open the document above for the full version.

Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 46 of 55 FCC Part 15.247 Report 15 EXHIBIT B - TEST SETUP PHOTOGRAPHS 15.1 Transmitter Radiated Emissions – Front View (Antenna Model: Antenna Mobile) 15.2 Transmitter Radiated Emissions – Rear View (Antenna Model: Antenna Mobile) Trimble Navigation Ltd. FCCID: JUP-59645 Report #：R0703211-247 Page 47 of 55 FCC Part 15.247 Report 15.3 Transmitter Radiated Emissions – Front View (Antenna Model: SPDA17918) 15.4 Transmitter Radiated Emissions – Rear View (Antenna Model: SPDA17918)