K4436023120VHF FM Transceiver

TK-7100 INSTRUCTION MANUAL VHF FM TRANSCEIVER TK-8100 UHF FM TRANSCEIVER TK-7102H E 00 Cover02.9.30, 1:41 PM1 THANK YOU! We are grateful you chose KENWOOD for your personal mobile applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product. MODELS COVERED BY THIS MANUAL The models listed below are covered by this manual: •TK-7100:VHF FM Transceiver •TK-8100:UHF FM Transceiver PRECAUTIONS Please observe the following precautions to prevent fire, personal injury, and transceiver damage. • Do not attempt to configure the transceiver while driving; it is too dangerous. • Do not modify the transceiver for any reason. • Do not expose the transceiver to long periods of direct sunlight, nor place it near heating appliances. • Do not place the transceiver in excessively dusty, humid, or wet areas, nor on unstable surfaces. • If an abnormal odor or smoke is detected coming from the transceiver, turn OFF the power immediately. Contact your KENWOOD dealer. TK-7102H E 00002.9.30, 1:41 PM1 i NOTICES TO THE USER uGovernment law prohibits the operation of unlicensed transmitters within the territories under government control. uIllegal operation is punishable by fine and/or imprisonment. uRefer service to qualified technicians only. SAFETY: It is important that the operator is aware of, and understands, hazards common to the operation of any transceiver. uEXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. Do not carry spare fuel containers in the trunk of your vehicle if your transceiver is mounted in the trunk area. uINJURY FROM RADIO FREQUENCY TRANSMISSIONS Do not operate your transceiver when somebody is either touching the antenna or standing within two to three feet of it, to avoid the possibility of radio frequency burns or related physical injury. uDYNAMITE BLASTING CAPS Operating the transceiver within 500 feet (150 m) of dynamite blasting caps may cause them to explode. Turn OFF your transceiver when in an area where blasting is in progress, or where “TURN OFF TWO-WAY RADIO” signs have been posted. If you are transporting blasting caps in your vehicle, make sure they are carried in a closed metal box with a padded interior. Do not transmit while the caps are being placed into or removed from the container. One or more of the following statements may be applicable: FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer for technical assistance. TK-7102H E 00i-ii02.9.30, 1:41 PM1 ii CONTENTS UNPACKING AND CHECKING EQUIPMENT ................................... 1 S UPPLIED ACCESSORIES..................................................................... 1 PREPARATION .................................................................................. 2 T OOLS REQUIRED.............................................................................. 2 POWER CABLE CONNECTION............................................................... 2 INSTALLING THE TRANSCEIVER.............................................................. 3 ORIENTATION .................................................................................... 4 F RONT PANEL................................................................................... 4 D ISPLAY............................................................................................ 5 REAR PANEL..................................................................................... 5 BASIC OPERATIONS ........................................................................ 6 S WITCHING POWER ON/ OFF ............................................................. 6 ADJUSTING THE VOLUME..................................................................... 6 SELECTING A CHANNEL....................................................................... 6 T RANSMITTING................................................................................... 6 RECEIVING........................................................................................ 6 SCAN .................................................................................................. 7 TEMPORARY DELETE.......................................................................... 7 REVERT CHANNEL.............................................................................. 7 DTMF CALLS .........................................................................…

Text truncated - open the document above for the full version.

MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS • Use only manufacturer or dealer supplied antenna. • Antenna Minimum Safe Distance: 120 cm (4 feet), 50% duty Cycle. • Antenna Gain: 0 dBd referenced to a dipole. The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety and Health Act) limits. • Antenna Mounting: The antenna supplied by the manufacturer or radio dealer must not be mounted at a location such that during radio transmission, any person or persons can come closer than the above indicated minimum safe distance to the antenna, i.e. 120 cm (4 feet) , 50% duty Cycle. • To comply with current FCC RF Exposure limits, the antenna must be installed at or exceeding the minimum safe distance shown above, and in accordance with the requirements of the antenna manufacturer or supplier. • Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or trunk lid, if the minimum safe distance is observed. • Base Station Installation: The antenna should be fixed-mounted on an outdoor permanent structure. RF Exposure compliance must be addressed at the time of installation. Antenna substitution: Do not substitute any antenna for the one supplied or recommended by the manufacturer or radio dealer. You may be exposing person or persons to excess radio frequency radiation. You may contact your radio dealer or the manufacturer for further instructions. Maintain a separation distance from the antenna to person(s) of at least 120 cm (4 feet) , 50% duty Cycle. “This transmitter is authorized to operate with a maximum duty factor of 50%, in typical push-to-talk mode, for satisfying FCC RF exposure compliance requirements.” You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to ensure the minimum separation distance (above) is maintained between the antenna and nearby persons for satisfying RF Exposure compliance. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure Environment, for work-related use, transmit only when person(s) are at least the minimum distance from the properly installed, externally mounted antenna. Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away the antenna/vehicle

September 9, 2003 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer RE: CONFIDENTIALITY REQUEST FOR MODEL: TK-7100-2, FCC ID: K4436023120. To Whom It May Concern: This letter serves as an official request for confidentiality under FCC Rule Section 0.459. We have requested that the Block Diagram Block DiagramBlock Diagram Block Diagram, , , , Schematic Diagrams Schematic DiagramsSchematic Diagrams Schematic Diagrams, , , , Circuit Circuit Circuit Circuit Description DescriptionDescription Description, , , , Parts List Parts ListParts List Parts List, , , , Active Devices Active DevicesActive Devices Active Devices and Tuning Procedure Tuning ProcedureTuning Procedure Tuning Procedure required to be submitted with this application be withheld from public review. The documents are company proprietary information that could never get into the possession of our competition. Please contact me if there is any information you may need. Sincerely, Tamaki Shimamura Communication Equipment Division Kenwood Corporation Akzo Nobel K. K. EMC Division Bancho Kaikan 12-1, Gobancho, Chiyoda-ku Tokyo 102-0076 Japan Tel.+81 3 5210 5411 Fax.+81 3 5216 2860 September 30, 2003 Federal Communications Commission Office of Engineering and Technology 7435 Oakland Mills Road Columbia, MD 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize PCTEST Engineering Laboratory, Inc. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C.862. This authorization expires one year from the current date. Sincerely, Akzo Nobel K. K. Junichi Okada Group Leader Technology Management Group EMC Division September 9, 2003 Letter of Attestation Model: TK-7100-2 VHF FM Transceiver This letter attests to the fact that Kenwood VHF FM Transceiver model TK-7100-2, FCC ID: K4436023120 meets the requirements of the FCC Rules, Parts 90.203(e) and (g). Compliance is achieved through the following method: Programming of this product’s transmit frequencies can be performed ONLY by the manufacturer or by service or maintenance personnel. The operator cannot program transmit frequencies using the equipment’s external operation controls. Tamaki Shimamura Communication Equipment Division Kenwood Corporation

Jan. 22, 2004 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer RE: RF exposure statement and users manual. To Whom It May Concern: We have selected a minimum safe distance larger than that of the MPE calculation, including margin. Please contact me if there is any information you may need. Sincerely, Tamaki Shimamura Communication Equipment Division Kenwood Corporation

December 31, 2003 Federal Communications Commission Equipment Approval Services 7435 Oakland Mills Road Columbia, MD 21046 Attn: Mr. Tim Harrington SUBJECT: Kenwood Corporation FCC ID: K4436023120 731 Confirmation No.: TC246695 Correspondence Reference No.: 10486 Request for Tech. Info.: 12/12/03 Dear Tim: Transmitted herewith, on behalf of Kenwood Corporation is an amendment provided in response to the request for technical information dated December 12, 2003. 1. Kenwood will consider using the training and labeling guidelines in TIA/EIA TSB-133. We note that the label currently in use is nearly identical to that recommended in the Standard. 2. We acknowledge the typo, and we will reissue the grant with the corrected power limitation of 41 W EIRP. 3. Re-calculating the minimum separation distance required for MPE compliance for Uncontrolled/General population yields a value of 99cm- these additional calculations are attached. Please note that the Section 90.205 allowance for max power + 20% was already included in the original calculations, and has been included again. Also, we note that the limits at the frequency range in question are 1.0 and 0.2 for Controlled and Uncontrolled, respectively, and not f/300 and f/1500, as stated in your email, per Section 1.1310. 4. We will reissue the grant with the revised Note, as requested. 5. Kenwood has confirmed that the label should be visible for under-the-dash installation. During the next manufacturing run of the EUT, Kenwood will place the label as shown in the attached photo. 6. Even using the minimum separation distance of 99 cm for Uncontrolled/General Population MPE compliance, we believe that a center-trunk mount of the antenna will still allow this distance to be maintained for back seat passengers. 7. We believe that the required separation distance of 99cm will always be maintained between the antenna and all people outside the vehicle, however, at the next printing of the Instruction Manual we will include the text as requested. We trust this information is sufficient to resolve FCC questions in this application. If you have any further questions, please do not hesitate to contact us. cc: Kenwood Corporation

Model: TK-7100-2 FCC ID:K4436023120 1 Front View Rear View Model: TK-7100-2 FCC ID:K4436023120 2 To p Vi e w Bottom View Model: TK-7100-2 FCC ID:K4436023120 3 Right View Left View

Model: TK-7100-2 FCC ID:K4436023120 Bottom View Bottom View Bottom View Bottom View

Model: TK-7100-2 FCC ID:K4436023120 1 TXRX Component Side View TXRX Foil Side View Model: TK-7100-2 FCC ID:K4436023120 2 Display Component Side View Display Foil Side View

Maximum Permissible Exposure (MPE) Evaluation Applicant:KENWOOD CORPORATION Equipment:VHF FM Tranceiver Model No.:TK-7100-2 FCC ID:K4436023120 MPE Calculations According to the OET Bulletin 65 (Edition 97-01) Where: S=Power density (in appropriate units, e.g. mW/cm 2 ) P=Power input to antenna (in appropriate units, e.g., mW) G=Power gain of the antenna in the direction of interest relative to an isotropic radiator R=Distance to the center of radiation of the antenna (appropriate units, e.g., cm) Tx Frequency=136 to 162 (MHz) Maximum peak power =43.98 (dBm)(=25W) Antenna gain=2.15 (dBi) S=1 (mW/cm 2 ) P=15000.00 (mW) (=Maximum peak power x 120% x Dutycycle 50%) G=1.64 (numeric) R=44.25 (cm) P = Value calculated according to CFR Part 90.205(q) Calculated minimum separation distance from antenna :44.25 (cm) S PG R π4 = 2 4R PG S π =

Maximum Permissible Exposure (MPE) Evaluation Applicant:KENWOOD CORPORATION Equipment:VHF FM Tranceiver Model No.:TK-7100-2 FCC ID:K4436023120 MPE Calculations According to the OET Bulletin 65 (Edition 97-01) Where: S=Power density (in appropriate units, e.g. mW/cm 2 ) P=Power input to antenna (in appropriate units, e.g., mW) G=Power gain of the antenna in the direction of interest relative to an isotropic radiator R=Distance to the center of radiation of the antenna (appropriate units, e.g., cm) Tx Frequency=136 to 162 (MHz) Maximum peak power =43.98 (dBm)(=25W) Antenna gain=2.15 (dBi) S=0.2 (mW/cm 2 ) P=15000.00 (mW) (=Maximum peak power x 120% x Dutycycle 50%) G=1.64 (numeric) R=98.95 (cm) P = Value calculated according to CFR Part 90.205(q) Calculated minimum separation distance from antenna :98.95 (cm) S PG R π4 = 2 4R PG S π =

TRUE TRUE 4 Regulation : FCC Part 2, 22, 74 & 90 Testing Laboratory KENWOOD CORPORATIONAkzo Nobel K. K.Kashima site FCC Registration Number : 90433 1-16-2, Hakusan, Midori-ku, Yokohama-shi1, Oaza Sunayama, Hasaki-machi, Kashima-gun Kanagawa, 226-8525 JapanIbaraki-ken, 314-0255 Japan Tel.: +81 45 939 7361 Fax.: +81 45 939 7364Tel.: +81 479 40 1097 Fax.: +81 479 46 1788 e-mail: [email protected] URL: www.akzoemc.co.jp Equipment typeMobile VHF FM Transceiver TrademarkKENWOOD Moles(s)TK-7100-2 Serial No.01 FCC ID K4436023120 Test Procedure(s)Akzo Nobel Document number 03-10-401 DeviationNo deviation Test ResultComplied Report NumberANKK-103269 Report issue date This equipment has been shown to be capable of compliance with the applicable standard(s) as indicated in the test report. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. This test report shall not be reproduced partially, or in full, without the prior written approval of Akzo Nobel K. K. The results and statements contained in this report pertain only to the equipment evaluated. Approved byTested by Takeshi Yamanaka / [Site Manager]Naoki Ikeda Applicant CERTIFICATE OF COMPLIANCE October 21, 2003 Report No : ANKK-103269FCC ID : K4436023120 TABLE OF CONTENTS Page SECTION 1.GENERAL INFORMATION3 SECTION 2.TEST AND MEASUREMENT DATA4 SECTION 3.MEASUREMENT RESULT5 SECTION 4.TEST DATA 4.1Carrier Output Power (Conducted)6 4.2Unwanted Emissions (Transmitter Conducted)7 4.3Field Strength of Spurious Radiation9 4.4Emission Masks (Occupied Bandwidth)11 4.5Transient Frequency Behavior14 4.6Audio Low Pass Filter (Voice Input)17 4.7Audio Frequency Response19 4.8Modulation Limiting21 4.9Frequency Stability (Temperature Variation)24 4.10Frequency Stability (Voltage Variation)26 4.11Necessary Bandwidth and Emission Bandwidth27 SECTION 5.VALIDITY OF TEST REPORT28 SECTION 6. DESCRIPTION OF TEST SITE28 APPENDIXPHOTOGRAPHS ©Akzo Nobel K. K. EMC Div.Page 2 of 28Version 6.0 Report No : ANKK-103269FCC ID : K4436023120 SECTION 1. GENERAL INFORMATION APPLICANT INFORMATION Company:KENWOOD CORPORATION Address:1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan Attenuation:Tamaki Shimamura Manager, Communications Equipment Division Telephone number :+81 45 939 7361 Fax number:+81 45 939 7364 DESCRIPTION OF TEST ITEM Kind of EUT:VHF FM Transceiver Condition of EUT:Pre Production Type:Mobile Trademark:KENWOOD Model number:TK-7100-2 Serial number:01 Emission Designation:16K0F3E(Wide) / 11K0F3E(Narrow) Frequency Range:136 to 162 MHz Output Power:5 to 25 W Number of Channel:64 ch Channel Spacing:25kHz (Wide) / 12.5 kHz (Narrow) Antenna Impedance:50 Ω Norminal TEST PERFORMED EUT Received: Test started: Test completed: Temperature:21.0 to 23.5 degrees C Humidity:45 to 48 % Atmospheric:101.3 to 102.5 kPa Voltage:DC 13.6 V Frequency:None TEST TRACABILITY Tracability to national standards of test result is achieved by means of calibration tractability to national or international standards. ABBREVIATIONS September 28, 2003 September 18, 2003 EUT = Equipment Under Test D.R.G. Antenna = Double Rigid Guide Antenna October 19, 2003 Cal Exp. = Calibration Expire ©Akzo Nobel K. K. EMC Div.Page 3 of 28Version 6.0 Report No : ANKK-103269FCC ID : K4436023120 SECTION 2. TEST AND MEASUREMENT DATA All test and measurements indicated in this document were performed in accordance with the Code of Federal Regulations Title 47 Part 2, Sub-part J as the following individual parts: Domestic Public Fixed radio Services Non Cellular Public Mobile Services Subpart H - Cellular Radiotelephone Service Alternative technologies and auxiliary service International Fixed Public Radiocommunication service Personal Communications Services Subpart H - Low Power Auxiliary Stations Stations in the Maritime Services Subpart E - general Technical Standards Subpart F - Equipment Authorization for Compulsory Ships Subpart K - Private Coast Stations and Marine Utility Stations Subpart V - Emergency Position Indicating Radiobeacons (EPIRB'S) Subpart W - Global Maritime Distress and Safety System (GMDSS) Subpart X - Voluntary Radio Installations Aviation Services Private Land Mobile radio Services Private Operational - Fixed Microwave Service Subpart A - General Mobile radio Service Subpart C - Radio Control (R/C) radio Service Subpart D - Citizens Band (CB) Radio Service Subpart E -Family radio Service Subpart F -Interactive Video and Data Service (IVDS) Amateur Radio Service Fixed Microwave Service FCC RULETEST ITEM Part 80 Part 80 Part 21 Part 22 Part 22 Part 22 Part 22 Part 80 Part 80 Part 23 Part 24 Part 74 Part 80 Part 80 Part 80 Part 80 N.A. N.A. Part 80 Part 80 Part 87 Part 90 Part 94 Part 95 Part 95 Part 95 Part 95 Part 95 Part 97 Part 101 Subpart S - Compulsory radiotelephone Installations for Small Passenger Boats Subpart T - Radiotelephone Installation Required for Vessels on the Great Lakes Subpart U - Radiotelephone Installations Required by the Bridge-to- Bridge Act YES N.A. N.A. N.A. N.A. N.A. N.A. Tested N.A. YES N.A. N.A. N.A. N.A. N.A. N.A. N.A. N.A. YES N.A. N.A. N.A. N.A. N.A. N.A. N.A. N.A. ©Akzo Nobel K. K. EMC Div.Page 4 of 28Version 6.0 Report No : ANKK-103269FCC ID : K4436023120 SECTION 3. MEASUREMENT RESULT Carrier Output Power (Conducted) Unwanted Emissions (Transmitter Conducted) Field Strength of Spurious Radiation Emission Masks (Occupied Bandwidth) Transient Frequency Behavior Audio Low Pass Filter (Voice Input) Audio Frequency Response Modulation Limiting Frequency Stability (Temperature Variation) Frequency Stability (Voltage Variation) Necessary Bandwidth and Emission Bandwidth Limitation on Results The test result of this report is effective equipment under test itself and under the test configuration d…

Text truncated - open the document above for the full version.