K4437673110UHF FM Transceiver

TK-7160/ TK-8160 TK-7160H/ TK-8160H VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL ÉMETTEUR-RÉCEPTEUR FM VHF/ ÉMETTEUR-RÉCEPTEUR FM UHF MODE D’EMPLOI TRANSCEPTOR FM VHF/ TRANSCEPTOR FM UHF MANUAL DE INSTRUCCIONES © B62-1829-00 (K,M) 09 08 07 06 05 04 03 02 01 00 VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-7160/ TK-8160 TK-7160H/ TK-8160H INSTRUCTION MANUAL ENGLISH i THANK YOU We are grateful you chose KENWOOD for your personal mobile applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be pleased with the quality and features of this product. MODELS COVERED BY THIS MANUAL The models listed below are covered by this manual: •TK-7160: VHF FM Transceiver •TK-7160H: High Power VHF FM Transceiver •TK-8160: UHF FM Transceiver •TK-8160H: High Power UHF FM Transceiver NOTICES TO THE USER ◆Government law prohibits the operation of unlicensed transmitters within the territories under government control. ◆Illegal operation is punishable by fine and/or imprisonment. ◆Refer service to qualified technicians only. SAFETY: It is important that the operator is aware of, and understands, hazards common to the operation of any transceiver. ◆EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. Do not carry spare fuel containers in the trunk of your vehicle if your transceiver is mounted in the trunk area. ◆INJURY FROM RADIO FREQUENCY TRANSMISSIONS Do not operate your transceiver when somebody is either touching the antenna or standing within 2 to 3 feet (60 to 90 cm) of it, to avoid the possibility of radio frequency burns or related physical injury. ◆DYNAMITE BLASTING CAPS Operating the transceiver within 500 feet (150 m) of dynamite blasting caps may cause them to explode. Turn OFF your transceiver when in an area where blasting is in progress, or where “TURN OFF TWO-WAY RADIO” signs have been posted. If you are transporting blasting caps in your vehicle, make sure they are carried in a closed metal box with a padded interior. Do not transmit while the caps are being placed into or removed from the container. ii PRECAUTIONS Observe the following precautions to prevent fire, personal injury, and transceiver damage. •Do not attempt to configure the transceiver while driving; it is too dangerous. •Do not disassemble or modify the transceiver for any reason. •Do not expose the transceiver to long periods of direct sunlight, nor place it near heating appliances. •Do not place the transceiver in excessively dusty, humid, or wet areas, nor on unstable surfaces. •If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, and contact your KENWOOD dealer. •Use of the transceiver while you are driving may be against traffic laws. Please check and observe the vehicle regulations in your area. •Do not use options not specified by KENWOOD. One or more of the following statements may be applicable: FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •Reorient or relocate the receiving antenna. •Increase the separation between the equipment and receiver. •Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. •Consult the dealer for technical assistance. iii CONTENTS UNPACKING AND CHECKING EQUIPMENT................................... 1 SUPPLIED ACCESSORIES..................................................................... 1 PREPARATION.................................................................................. 2 TOOLS REQUIRED.............................................................................. 2 POWER CABLE CONNECTION............................................................... 2 INSTALLING THE TRANSCEIVER.............................................................. 3 CONNECTING A MICROPHONE............................................................... 4 GETTING ACQUAINTED................................................................... 5 FRONT PANEL................................................................................... 5 DISPLAY........................................................................................... 7 R EAR PANEL..................................................................................... 7 PROGRAMMABLE FUNCTIONS...................................................... 8 BASIC OPERATIONS...................................................................... 10 SWITCHING POWER ON/ OFF........................................................... 10 ADJUSTING THE VOLUME................................................................... 10 SELECTING A ZONE AND CHANN…

Text truncated - open the document above for the full version.

Oct. 20th, 2004 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer RE: CONFIDENTIALITY REQUEST FOR MODEL: TK-8160-K, FCC ID: K4437673110. To Whom It May Concern: This letter serves as an official request for permanent confidentiality pursuant to 47 CFR Section 0.459 of the Commission Rules. We have requested that the Block Diagram, Schematic Diagrams, Circuit Description, Parts List, Active Devices and Tuning Procedure required to be submitted with this application be withheld from public review. The documents are company proprietary information that could never get into the possession of our competition. Please contact me if you require any additional information. Sincerely, Tamaki Shimamura Communication Equipment Division Kenwood Corporation

May 20th, 2004 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize Akzo Nobel K.K. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C.862. This agreement expires one year from the current date. Sincerely, Tamaki Shimamura Communication Equipment Division Kenwood Corporation

Akzo Nobel K. K. EMC Division Bancho Kaikan 12-1, Gobancho, Chiyoda-ku Tokyo 102-0076 Japan Tel.+81 3 5210 5411 Fax.+81 3 5216 2860 October 20, 2004 Federal Communications Commission Office of Engineering and Technology 7435 Oakland Mills Road Columbia, MD 21046 RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern: We, the undersigned, hereby authorize MET Laboratories, Inc. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C.862. This authorization expires one year from the current date. Sincerely, Junichi Okada Group Leader Tokyo Office EMC Division Akzo Nobel K. K.

TK-8160-K FCC ID: K4437673110 Front View Rear View TK-8160-K FCC ID: K4437673110 Top View Bottom View TK-8160-K FCC ID: K4437673110 Right View Left View

TK-8160-K FCC ID: K4437673110

TK-8160-K FCC ID: K4437673110 TXRX Component Side View TXRX Foil Side View TK-8160-K FCC ID: K4437673110 Display Component Side View Display Foil Side View

Maximum Permissible Exposure (MPE) Evaluation Applicant:Kenwood Corporation Equipmen t:UHF FM TRANSCEIVER Model No.:TK-8160-K FCC ID:K4437673110 IC:282F-37673110 MPE Calculations According to the OET Bulletin 65 (Edition 97-01) Where: S=Power density (in appropriate units, e.g. mW/cm 2 ) P=Power input to antenna (in appropriate units, e.g., mW) G=Power gain of the antenna in the direction of interest relative to an isotropic radiator R=Distance to the center of radiation of the antenna (appropriate units, e.g., cm) Tx Frequency=450 to 490 (MHz) Maximum peak power =(dBm)(=25W) Antenna gain=(dBi) S=(mW/cm 2 ) P=(mW) (=Maximum peak power x 120% x Dutycycle 50%) G=(numeric) R=(cm) P = Value calculated according to CFR Part 90.205(q) Calculated minimum separation distance from antenna :80.79 (cm) 1.64 80.79 43.98 2.15 0.30 15000.00 S PG R π4 = 2 4R PG S π =

MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS • Use only manufacturer or dealer supplied antenna. • Antenna Minimum Safe Distance: 120 cm (4 feet), 50% duty Cycle. • Antenna Gain: 0 dBd referenced to a dipole. The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety and Health Act) limits. • Antenna Mounting: The antenna supplied by the manufacturer or radio dealer must not be mounted at a location such that during radio transmission, any person or persons can come closer than the above indicated minimum safe distance to the antenna, i.e. 120 cm (4 feet) , 50% duty Cycle. • To comply with current FCC RF Exposure limits, the antenna must be installed at or exceeding the minimum safe distance shown above, and in accordance with the requirements of the antenna manufacturer or supplier. • Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or trunk lid, if the minimum safe distance is observed. • Base Station Installation: The antenna should be fixed-mounted on an outdoor permanent structure. RF Exposure compliance must be addressed at the time of installation. Antenna substitution: Do not substitute any antenna for the one supplied or recommended by the manufacturer or radio dealer. You may be exposing person or persons to excess radio frequency radiation. You may contact your radio dealer or the manufacturer for further instructions. Maintain a separation distance from the antenna to person(s) of at least 120 cm (4 feet) , 50% duty Cycle. “This transmitter is authorized to operate with a maximum duty factor of 50%, in typical push-to-talk mode, for satisfying FCC RF exposure compliance requirements.” You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to ensure the minimum separation distance (above) is maintained between the antenna and nearby persons for satisfying RF Exposure compliance. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure Environment, for work-related use, transmit only when person(s) are at least the minimum distance from the properly installed, externally mounted antenna. Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away from the antenna/vehicle

TRUE TRUE 4 Regulation : FCC Part 2, 22, 74, 90, 90.210, 95 Kenwood CorporationAkzo Nobel K. K. 1-16-2, Hakusan, Midori-ku, Yokohama-shiKashima No.1 , No3 , No.10 site Kanagawa, 226-8525 JapanFCC Registration Number : 90433 Tel.: +81 45 939 6254 Fax.: +81 45 939 70931, Oaza Sunayama, Hasaki-machi, Kashima-gun Ibaraki-ken, 314-0255 Japan Tel.: +81 479 40 1097 Fax.: +81 479 46 1788 e-mail: [email protected] URL: www.akzoemc.co.jp Equipment typeUHF FM TRANSCEIVER TrademarkKENWOOD Model(s)TK-8160-K Serial No.13 FCC ID K4437673110 Measurement MethodANSI/TIA/EIA-603 No deviation Test ResultComplied Report NumberANKK-104216 Report issue date Approved byTested by Takeshi Yamanaka / [Site Manager]Naoki Ikeda This equipment has been shown to be capable of compliance with the applicable standard(s) as indicated in the test report. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. This test report shall not be reproduced partially, or in full, without the prior written approval of Akzo Nobel K. K. The results and statements contained in this report pertain only to the equipment evaluated. Applicant CERTIFICATE OF COMPLIANCE October 14, 2004 Deviation from standard(s) Testing Laboratory ©Akzo Nobel K. K. EMC Div.Page 1 of 27Version 6.1 Report No : ANKK-104216FCC ID : K4437673110 TABLE OF CONTENTS Page SECTION 1.GENERAL INFORMATION3 SECTION 2.TEST AND MEASUREMENT DATA4 SECTION 3.MEASUREMENT RESULT5 SECTION 4.TEST DATA 4.1Carrier Output Power (Conducted)6 4.2Unwanted Emissions (Transmitter Conducted)7 4.3Field Strength of Spurious Radiation9 4.4Emission Masks (Occupied Bandwidth)12 4.5Transient Frequency Behavior15 4.6Audio Frequency Response / Audio Low Pass Filter (Voice Input)18 4.7Modulation Limiting20 4.8Frequency Stability (Temperature Variation)23 4.9Frequency Stability (Voltage Variation)25 4.10Necessary Bandwidth and Emission Bandwidth26 SECTION 5.VALIDITY OF TEST REPORT27 SECTION 6. DESCRIPTION OF TEST SITE27 APPENDIXPHOTOGRAPHS ©Akzo Nobel K. K. EMC Div.Page 2 of 27Version 6.1 Report No : ANKK-104216FCC ID : K4437673110 SECTION 1. GENERAL INFORMATION APPLICANT INFORMATION Company:Kenwood Corporation Address:1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan Attenuation:Tamaki Shimamura Manager, Communications Equipment Division Telephone number :+81 45 939 6254 Fax number:+81 45 939 7093 DESCRIPTION OF TEST ITEM Kind of EUT:Mobile Device Condition of EUT:Pre Production Type:Mobile Trademark:KENWOOD Model number:TK-8160-K Serial number:13 Emission Designation:16K0F3E(Wide) / 11K0F3E(Narrow) Frequency Range:450 to 490 MHz Output Power:5 to 25 W Number of Channel:128 Channel Spacing:25 kHz (Wide) / 12.5 kHz (Narrow) Antenna Impedance:50 Ω Norminal TEST PERFORMED EUT Received: Test started: Test completed: Temperature:23 to 28 degrees C Humidity:45 to 64 % Atmospheric:100.4 to 102.1 kPa Voltage:DC 13.6 V Frequency:None TEST TRACABILITY ABBREVIATIONS September 27, 2004 September 27, 2004 EUT = Equipment Under Test D.R.G. Antenna = Double Rigid Guide Antenna October 06, 2004 Cal Exp. = Calibration Expire Tracability to national standards of test result is achieved by means of calibration tractability to national or international standards. ©Akzo Nobel K. K. EMC Div.Page 3 of 27Version 6.1 Report No : ANKK-104216FCC ID : K4437673110 SECTION 2. TEST AND MEASUREMENT DATA All test and measurements indicated in this document were performed in accordance with the Code of Federal Regulations Title 47 Part 2, Sub-part J as the following individual parts: Domestic Public Fixed radio Services Non Cellular Public Mobile Services Subpart H - Cellular Radiotelephone Service Alternative technologies and auxiliary service International Fixed Public Radiocommunication service Personal Communications Services Subpart H - Low Power Auxiliary Stations Stations in the Maritime Services Subpart E - general Technical Standards Subpart F - Equipment Authorization for Compulsory Ships Subpart K - Private Coast Stations and Marine Utility Stations Subpart V - Emergency Position Indicating Radiobeacons (EPIRB'S) Subpart W - Global Maritime Distress and Safety System (GMDSS) Subpart X - Voluntary Radio Installations Aviation Services Private Land Mobile radio Services Private Operational - Fixed Microwave Service Subpart A - General Mobile radio Service Subpart C - Radio Control (R/C) radio Service Subpart D - Citizens Band (CB) Radio Service Subpart E -Family radio Service Subpart F -Interactive Video and Data Service (IVDS) Amateur Radio Service Fixed Microwave Service FCC RULETEST ITEM Part 80 Part 80 Part 21 Part 22 Part 22 Part 22 Part 22 Part 80 Part 80 Part 23 Part 24 Part 74 Part 80 Part 80 Part 80 Part 80 N.A. N.A. Part 80 Part 80 Part 87 Part 90 Part 94 Part 95 Part 95 Part 95 Part 95 Part 95 Part 97 Part 101 Subpart S - Compulsory radiotelephone Installations for Small Passenger Boats Subpart T - Radiotelephone Installation Required for Vessels on the Great Lakes Subpart U - Radiotelephone Installations Required by the Bridge-to- Bridge Act YES N.A. N.A. N.A. N.A. N.A. N.A. Tested N.A. YES N.A. N.A. N.A. N.A. N.A. N.A. N.A. N.A. YES N.A. YES N.A. N.A. N.A. N.A. N.A. N.A. ©Akzo Nobel K. K. EMC Div.Page 4 of 27Version 6.1 Report No : ANKK-104216FCC ID : K4437673110 SECTION 3. MEASUREMENT RESULT TEST ITEMRESULTS Carrier Output Power (Conducted)PASS Unwanted Emissions (Transmitter Conducted)PASS Field Strength of Spurious RadiationPASS Emission Masks (Occupied Bandwidth)PASS Transient Frequency BehaviorPASS Audio Low Pass Filter (Voice Input)PASS Audio Frequency ResponsePASS Modulation LimitingPASS Frequency Stability (Temperature Variation)PASS Frequency Stability (Voltage Variation)PASS Necessary Bandwidth and Emission BandwidthPASS Limitatio…

Text truncated - open the document above for the full version.

APPENDIX Report No : ANKK-104216FCC ID : K4437673110 PHOTOGRAPHS OF MEASUREMENT SET-UP 4.1 Carrier Output Power (Conducted) Accordance with TIA-603-B 2.2.1.2 4.2 Unwanted Emission (Conducted Spurious) Accordance with TIA-603-B 2.2.13.2 ©Akzo Nobel K. K. EMC Div.Page 2 of 7Version 6.1 Report No : ANKK-104216FCC ID : K4437673110 4.3 Field Strength of Spurious Radiation : Front view Accordance with TIA-603-B 2.2.12.2 4.3 Field Strength of Spurious Radiation : Rear view ©Akzo Nobel K. K. EMC Div.Page 3 of 7Version 6.1 Report No : ANKK-104216FCC ID : K4437673110 4.4 Emission Mask Accordance with TIA-603-B 2.2.11.2 4.5 Transient Frequency Behavior Accordance with TIA-603-B 2.2.19.3 ©Akzo Nobel K. K. EMC Div.Page 4 of 7Version 6.1 Report No : ANKK-104216FCC ID : K4437673110 4.6 Audio Frequency Response Accordance with TIA-603-B 2.2.6.2.2 4.7 Modulation Limiting Accordance with TIA-603-B 2.2.3.2 ©Akzo Nobel K. K. EMC Div.Page 5 of 7Version 6.1 Report No : ANKK-104216FCC ID : K4437673110 4.8 Frequency Stability (Temperature Variation) Accordance with TIA-603-B 2.3.2.2 4.8 Frequency Stability (Temperature Variation) : Inner view ©Akzo Nobel K. K. EMC Div.Page 6 of 7Version 6.1 Report No : ANKK-104216FCC ID : K4437673110 4.9 Frequency Stability (Voltage Variation) Accordance with TIA-603-B 2.2.2.2 ©Akzo Nobel K. K. EMC Div.Page 7 of 7Version 6.1