K44407702UHF FM TRANSCEIVER

TK-7302V/ TK-8302U TK-7302H/ TK-8302H TK-7302HV/ TK-8302HU VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL ÉMETTEUR-RÉCEPTEUR FM VHF/ ÉMETTEUR-RÉCEPTEUR FM UHF MODE D’EMPLOI TRANSCEPTOR FM VHF/ TRANSCEPTOR FM UHF MANUAL DE INSTRUCCIONES © B62-2167-00 (K,K2) 09 08 07 06 05 04 03 02 01 00 CHVOL VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-7302V/ TK-8302U TK-7302H/ TK-8302H TK-7302HV/ TK-8302HU INSTRUCTION MANUAL ENGLISH  One or more of the following statements may be applicable: FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the nstructon manual. The user could lose the authorty to operate ths equpment f an unauthorzed change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection aganst harmful nterference n a resdental nstallaton. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followng measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer for techncal assstance. Thank You We are grateful you have chosen Kenwood for your personal moble applcatons. This instruction manual covers only the basic operations of your portable radio. Ask your dealer for information on any customized features they may have added to your radio. noTices To The user ◆ Government law prohibits the operation of unlicensed transmitters within the territories under government control. ◆ Illegal operation is punishable by fine and/or imprisonment. ◆ Refer service to qualified technicians only. SAFETY: It is important that the operator is aware of, and understands, hazards common to the operation of any transceiver. ◆ EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. Do not carry spare fuel containers in the trunk of your vehicle if your transceiver is mounted in the trunk area. ◆ INJURY FROM RADIO FREQUENCY TRANSMISSIONS Do not operate your transceiver when somebody is either touching the antenna or standing within 2 to 3 feet (60 to 90 cm) of it, to avoid the possibility of radio frequency burns or related physcal njury. ◆ DYNAMITE BLASTING CAPS Operating the transceiver within 500 feet (150 m) of dynamite blasting caps may cause them to explode. Turn OFF your transceiver when in an area where blasting is in progress, or where “TURN OFF TWO-WAY RADIO” signs have been posted. If you are transporting blasting caps in your vehicle, make sure they are carried in a closed metal box with a padded interior. Do not transmit while the caps are being placed into or removed from the container.  CONTENTS GeTTING STARTeD ................................................................................................1 GeTTING ACQUAINTeD .........................................................................................3 PROGRAmmABle FUNCTIONS .............................................................................4 BASIC OPeRATIONS ...............................................................................................5 SCAN ........................................................................................................................6 DTmF CAllS ...........................................................................................................7 SIGNAlING ..............................................................................................................8 FleetSync: AlPHANUmeRIC 2-WAY PAGING FUNCTION .....................................9 ADv ANCeD OPeRATIONS ....................................................................................10 BACkGROUND OPeRATIONS ..............................................................................12 PrecauTions Observe the following precautions to prevent fire, personal injury, and transceiver damage. • Do not attempt to configure the transceiver while driving; it is too dangerous. • Do not disassemble or modify the transceiver for any reason. • Do not expose the transceiver to long periods of direct sunlight, nor place it near heating applances. • If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, and contact your Kenwood dealer. • Use of the transceiver while you are driving may be against traffic laws. Please check and observe the vehicle regulations in your area. • Do not use options not specified by Kenwood. ◆ The transceiver operates in 12 v negative ground systems only! Check the battery polarity and voltage of the vehicle before installing the transceiver. ◆ Use only the supplied DC power cable or a Kenwood optional DC power cable. ◆ Do not cut and/or remove the fuse holder on the DC power cable. For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set so the transceiver will not break loose in the event of a collision.  GETTING STARTED Note: The following instructions are for use by your Kenwood dealer, an authorized Kenwood service facility, or the factory. Supplied AcceSSorieS Carefully …

Text truncated - open the document above for the full version.

Nov. 20th 2009 MET Laboratories 914 West Patapsco Ave. Baltimore MD 21230 Attn: Reviewing Engineer RE: CONFIDENTIALITY REQUEST FOR MODEL: TK-8302H-1, TK-8302HU-1, FCC ID: K44407702. To whom it may concern: This letter serves as an official request for permanent confidentiality pursuant to 47 CFR Section 0.459 of the Commission Rules. We have requested that the Block Diagram, Schematic Diagrams, Circuit Description, Parts List, Active Devices and Tuning Procedure required to be submitted with this application be withheld from public review. The documents are company proprietary information that could never get into the possession of our competition. Please contact me if you require any additional information. Sincerely, Tamaki Shimamura Communications Equipment Division Kenwood Corporation 1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan

Nov. 20th, 2009 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer Subject: Justify Extended Frequency Range for MODEL: TK-8302H-1, TK-8302HU-1, FCC ID: K44407702 To Whom It May Concern: This letter serves justification for extended frequencies This device has design capability to operate in the frequency band 450 to 520 MHz and complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transit frequencies using the normally accessible external controls. Please note that Licensed End Users do not have access to any external controls that will allow them to program the equipment. Equipment programming is the responsibility of Kenwood approved Service Agents. The table below has been collated using information from CFR Part 2.106 and lists the Frequency Ranges and Rule Parts, which permit the operation of this equipment inside the United States of America. Freq. Range (MHz) Part 90 Part 22Part 74Part 95A 450.0000-454.0000 x x 454.0000-455.0000 x 455.0000-456.0000 x 456.0000-460.0000 x x 460.0000-462.5375 x 462.5375-462.7375 x 462.7375-467.5375 x 467.5375-467.7375 x 467.7375-470.0000 x 470.0000-512.0000 x x x 512.0000-520.0000 x Table 1 – Frequency Range and Rule Parts - (47 CFR Part 2.106) It is understood that a grant note code may be added to the grant which indicates this required operation. Please contact me if you require any additional information. Sincerely, Tamaki Shimamura Communications Equipment Division Kenwood Corporation 1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan

Aug. 17th, 2009 MET Laboratories 914 West Patapsco Ave. Baltimore MD 21230 Attn: Reviewing Engineer RE: LETTER OF AGENT AUTHORIZATION To whom it may concern: We, the undersigned, hereby authorize Sae Hagino of Intertek Japan K.K. to act on our behalf in all matters relating to this application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C.862. This agreement expires one year from the current date. Sincerely, Tamaki Shimamura Communications Equipment Division Kenwood Corporation 1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan

TK-8302H-1, TK-8302HU-1 FCC ID: K44407702 Front View Rear View TK-8302H-1, TK-8302HU-1 FCC ID: K44407702 Top View TK-8302H-1 Bottom View TK-8302H-1, TK-8302HU-1 FCC ID: K44407702 TK-8302HU-1 Bottom View Right View Left View

TK-8302H-1, TK-8302HU-1 FCC ID: K44407702 TK-8302H-1 TK-8302HU-1

TK-8302H-1, TK-8302HU-1 FCC ID: K44407702 TXRX Component Side View TXRX Foil Side View TK-8302H-1, TK-8302HU-1 FCC ID: K44407702 Display Component Side View Display Foil Side View TK-8302H-1, TK-8302HU-1 FCC ID: K44407702 TXRX Display

Maximum Permissible Exposure (MPE) Evaluation Applicant: Kenwood Corporation Equipmen t: UHF FM TRANSCEIVER Model No.: TK-8302H-1, TK-8302HU-1 FCC ID: K44407702 MPE Calculations According to the OET Bulletin 65 (Edition 97-01) Where: S=Power density (in appropriate units, e.g. mW/cm 2 ) P=Power input to antenna (in appropriate units, e.g., mW) G=Power gain of the antenna in the direction of interest relative to an isotropic radiator R=Distance to the center of radiation of the antenna (appropriate units, e.g., cm) Tx Frequency=450 to 520 (MHz): FCC Maximum peak power =(dBm)(=45W) Antenna gain=(dBi) S=(mW/cm 2 ) P=(mW) (=Maximum peak power x 120% x Dutycycle 50%) G=(numeric) R=(cm) P = Value calculated according to CFR Part 90.205(s) Calculated minimum separation distance from antenna :108.40 (cm) 1.64 108.40 46.53 2.15 0.30 27000.00 S PG R π4 = 2 4R PG S π =

MANDATORY SAFETY INSTRUCTIONS TO INSTALLERS AND USERS • Use only manufacturer or dealer supplied antenna. • Antenna Minimum Safe Distance: 120 cm (4 feet), 50% duty Cycle. • Antenna Gain: 0 dBd referenced to a dipole. The Federal Communications Commission has adopted a safety standard for human exposure to RF (Radio Frequency) energy which is below the OSHA (Occupational Safety and Health Act) limits. • Antenna Mounting: The antenna supplied by the manufacturer or radio dealer must not be mounted at a location such that during radio transmission, any person or persons can come closer than the above indicated minimum safe distance to the antenna, i.e. 120 cm (4 feet) , 50% duty Cycle. • To comply with current FCC RF Exposure limits, the antenna must be installed at or exceeding the minimum safe distance shown above, and in accordance with the requirements of the antenna manufacturer or supplier. • Vehicle installation: The antenna can be mounted at the center of a vehicle metal roof or trunk lid, if the minimum safe distance is observed. • Base Station Installation: The antenna should be fixed-mounted on an outdoor permanent structure. RF Exposure compliance must be addressed at the time of installation. Antenna substitution: Do not substitute any antenna for the one supplied or recommended by the manufacturer or radio dealer. You may be exposing person or persons to excess radio frequency radiation. You may contact your radio dealer or the manufacturer for further instructions. Maintain a separation distance from the antenna to person(s) of at least 120 cm (4 feet) , 50% duty Cycle. “This transmitter is authorized to operate with a maximum duty factor of 50%, in typical push-to-talk mode, for satisfying FCC RF exposure compliance requirements.” You, as the qualified end-user of this radio device must control the exposure conditions of bystanders to ensure the minimum separation distance (above) is maintained between the antenna and nearby persons for satisfying RF Exposure compliance. The operation of this transmitter must satisfy the requirements of Occupational/Controlled Exposure Environment, for work-related use, transmit only when person(s) are at least the minimum distance from the properly installed, externally mounted antenna. Transmit only when people outside the vehicle are at least the recommended minimum lateral distance away from the antenna/vehicle

Report No :JT09120015 FCC ID : K44407702 TRUE FALSE 3 REGULATION :FCC Part 2, 22, 74, 90, 90.210, 95 Kenwood CorporationIntertek Japan K. K. Kashima Laboratory 1-16-2, Hakusan, Midori-ku, Yokohama-shi3-2, Sunayama, Kamisu-shi, Ibaraki-ken Kanagawa, 226-8525 Japan314-0255 Japan Tel.: +81 45 939 6254 Fax.: +81 45 939 7097Tel.: +81 479 40 1097 Fax.: +81 479 46 1788 Intertek Japan K. K. Tochigi Laboratory 870 Nakaawano, Kanuma-shi, Tochigi-ken 322-0306 Japan Tel.: +81 289 86 7121 Fax.: +81 289 86 7126 URL: http://www.japan.intertek-etlsemko.com Equipment typeUHF FM TRANSCEIVER TrademarkKENWOOD Model(s) TK-8302H-1TK-8302HU-1 Serial No. FCC ID K44407702 Test ResultComplied Report NumberJT09120015 Report issue date Approved byTested by Kazuo GokitaKoichi Wagatsuma [Site Manager] This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Applicant TEST REPORT Testing Laboratory January 04, 2010 00000005 Intertek Japan K.K.Page 1 of 42Version 0.1 Report No :JT09120015 FCC ID : K44407702 In Accordance with FCC Rules and Regulations, Volume II, Part 2 and 90 Sub-part 2.1033 (c)(1) Applicant and Manufacture Information APPLICANT Company:Kenwood Corporation Address:1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan Contact Person:Tamaki Shimamura Manager, Communications Equipment Division MANUFACTURER Company:Kenwood Corporation Address:1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan (c)(2) FCC ID FCC ID:K44407702 Model number: TK-8302H-1TK-8302HU-1 Serial number:00000005 (c)(3) Instruction Manual(S) Instruction manual(s):Please refer to attached Exhibits F (c)(4) Type of Emission Emission Designation:16K0F3E(Wide) /11K0F3E(Narrow) (c)(5) Frequency range Frequency Range:450 to 520 MHz (c)(6) Power Rating Output Power:5 to 45 W Type:Continuously Variable (c)(7) Maximum Power Rating Output Power:45 W (c)(8): Voltages & currents in all elements in final RF stage, including final transistor or solid-state device Collector Current:15.0 A(Maximum) Collector Voltage:DC 13.6 V Supply Voltage:DC 13.6 V Other Information Number of Channel:16 Maximum Deviation:5 kHz / 2.5kHz Frequency Stability:2.5 ppm Antenna Impedance:50 Ω Norminal Note Intertek Japan K.K.Page 2 of 42Version 0.1 Report No :JT09120015 FCC ID : K44407702 TABLE OF CONTENTS Page SECTION 1. GENERAL INFORMATION4 SECTION 2. SUMMARY OF TEST RESULT5 SECTION 3. TEST AND MEASUREMENT DATA6 SECTION 4. INFORMATION ABOUT EUT AND SUPPORT EQUIPMENT(S)7 SECTION 5. SUPPORT EQUIPMENT8 SECTION 6. USED CABLE(S)9 SECTION 7. TEST CONFIGURATION10 SECTION 8. OPERATING CONDITION11 SECTION 9. MEASUREMENT UNCERTAINTY12 SECTION 10. TEST DATA 10.1Carrier Output Power (Conducted)13 10.2Unwanted Emissions (Transmitter Conducted)15 10.3Field Strength of Spurious Radiation18 10.4Emission Masks (Occupied Bandwidth)22 10.5Transient Frequency Behavior26 10.6Audio Frequency Response / Audio Low Pass Filter (Voice Input)30 10.7Modulation Limiting33 10.8Frequency Stability (Temperature Variation)37 10.9Frequency Stability (Voltage Variation)40 10.10Necessary Bandwidth and Emission Bandwidth42 APPENDIXPHOTOGRAPHS Intertek Japan K.K.Page 3 of 42Version 0.1 Report No :JT09120015 FCC ID : K44407702 SECTION 1. GENERAL INFORMATION TEST PERFOMED LocationTochigi No1, No.3 Test Site and Kashima No.1 Test Site EUT Received Date of Testto Standard AppliedFCC Part 2, 22, 74, 90, 90.210, 95 Measurement MethodANSI/TIA-603-C-2004 Deviation from Standard(s)Not applicable QUALIFICATIONS OF TESTING LABORATORY(Kashima Lab.) ACCREDITATIONSCOPELAB. CODERemarks NVLAPEMC Testing100290-0 VLACEMC TestingVLAC-008-1JAPAN BSMIEMC TestingSL2-IN-E-6008TAIWAN FILING VCCIEMC TestingJAPAN FCCEMC TestingDesignation Number:JP0008USA ICEMC TestingIC-2042K-1, IC-2042K-3CANADA SAUDI ARABIAEMC TestingN/A QUALIFICATIONS OF TESTING LABORATORY(Tochigi Lab.) ACCREDITATIONSCOPELAB. CODERemarks VLACEMC TestingVLAC-008-5JAPAN BSMIEMC TestingSL-2-IN-E-6017, SL-2-AI-E-6017TAIWAN FILING VCCIEMC TestingJAPAN FCCEMC TestingDesignation Number:JP0011USA ICEMC TestingIC-2042P-1, IC-2042P-2CANADA SAUDI ARABIAEMC TestingN/A ABBREVIATIONS EUTDoC AMNISN LISNQ-P AMPAVG ATTPK ANTCal BBAN/A DIPLCD AEAssociated Equipment4LEVEL FSK 4LEVEL Frequency Shift Key GMSKCW ID FMC4FM PTTPush to TalkAFC R-257, C-260, C-284, T-374, T-375 R-258, C-261, C-285, T-376, T-377 R-259, C-262, T-378 Gaussian Maximum Shift Key Frequency ModulationConstant envelope 4 Level FM Continuously Repeating bit stream Automatic frequency control Dipole AntennaLiquid-Crystal Display December 10, 2009 December 14, 2009December 24, 2009 Line Impedance Stabilization Network Equipment Under Test Artificial Mains Network Declaration of Conformity Impedance Stabilization Network Quasi-peak Amplifier Attenuator Antenna Broadband Antenna Average Peak Calibration Not applicable or Not available R-274, C-280, C-281, T-353, T-359 R-272, C-276, C-277, T-360, T-361 R-576, C-590, T-362 R-788, C-278, C-279, T-351, T-352 Intertek Japan K.K.Page 4 of 42Version 0.1 Report No :JT09120015 FCC ID : K44407702 SECTION 2. SUMMARY OF TEST RESULT FCCTEST ITEMRESULTS Part2Part22Part74Part90 2.1046-74.461-Carrier Output Power (Conducte…

Text truncated - open the document above for the full version.

Report No :JT09120015 FCC ID : K44407702 APPENDIX Intertek Japan K.K.Page 1 of 6Version 0.1 Report No :JT09120015 FCC ID : K44407702 PHOTOGRAPHS OF MEASUREMENT SET-UP 10.1 Carrier Output Power (Conducted) 10.2 Unwanted Emission (Conducted Spurious) Intertek Japan K.K.Page 2 of 6Version 0.1 Report No :JT09120015 FCC ID : K44407702 10.3 Field Stren gth of Spurious Radiation : Front view 10.3 Field Stren gth of Spurious Radiation : Rear view Intertek Japan K.K.Page 3 of 6Version 0.1 Report No :JT09120015 FCC ID : K44407702 10.4 Emission Masks 10.5 Transient Fre quency Behavior Intertek Japan K.K.Page 4 of 6Version 0.1 Report No :JT09120015 FCC ID : K44407702 10.6 Audio Fre quency Response 10.7 Modulation Limitin g Intertek Japan K.K.Page 5 of 6Version 0.1 Report No :JT09120015 FCC ID : K44407702 10.8 , 10.9 Frequency Stability : Outer view 10.8 , 10.9 Frequency Stability : Inner view Intertek Japan K.K.Page 6 of 6Version 0.1