K44473100Remote Control Head

One or more of the following statements may be applicable to this equipment: FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved by the party responsible/ JVCKENWOOD. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer for technical assistance. B5K-0119-10 (M) © 2015 This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. Regarding the operation, refer to the transceiver instruction manual.

One or more of the following statements may be applicable to this equipment: FCC WARNING This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made. INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer for technical assistance. B5K-0119-00 (M) © 2015 This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

Dec. 17th, 2014 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer RE: LETTER OF AGENT AUTHORIZATION To whom it may concern: We, the undersigned, hereby authorize any individual within Intertek Japan K.K. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C.862. This agreement expires one year from the current date. Sincerely, Tamaki Shimamura Communications Equipment Division 1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan

Dec. 17th 2014 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer RE: CONFIDENTIALITY REQUEST FOR MODEL: KCH-20R-M, FCC ID: K44473100 To whom it may concern: This letter serves as an official request for permanent confidentiality pursuant to 47 CFR Section 0.459 of the Commission Rules. We have requested that the Block Diagram, Schematic Diagrams, Circuit Description, Parts List, and Active Devices required to be submitted with this application be withheld from public review. The documents are company proprietary information that could never get into the possession of our competition. Please contact me if you require any additional information. Sincerely, Tamaki Shimamura Communications Equipment Division 1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan

KCH-20R-M FCC ID: K44473100 IC: 282F-473100 Front view Top view KCH-20R-M FCC ID: K44473100 IC: 282F-473100 Rear view Bottom view KCH-20R-M FCC ID: K44473100 IC: 282F-473100 Right view Left view

KCH-20R-M FCC ID: K44473100 IC: 282F-473100 Rear view Rear view KCH-20R-M FCC ID: K44473100 IC: 282F-473100 Top view

KCH-20R-M FCC ID: K44473100 IC: 282F-473100 KCH-20R-M FCC ID: K44473100 IC: 282F-473100 KCH-20R-M FCC ID: K44473100 IC: 282F-473100

Maximum Permissible Exposure (MPE) Evaluation Applicant: JVC KENWOOD Corporation Equipment: REMOTE CONTROL HEAD FCC Model No.: KCH-20R-M FCC ID: K44473100 MPE Calculations According to the OET Bulletin 65 (Edition 97-01) Where: S=Power density (in appropriate units, e.g. mW/cm 2 ) P=Power input to antenna (in appropriate units, e.g., mW) G=Power gain of the antenna in the direction of interest relative to an isotropic radiator R=Distance to the center of radiation of the antenna (appropriate units, e.g., cm) Tx Frequency= 2402 to 2480 [MHz] Maximum peak power=[dBm] Antenna gain=[dBi] P=[mW] G=[numeric] R=[cm] Calculated Power density :[mW/cm 2 ]0.0004 20.00 -1.19 4.24 0.76 2.65 : From Test Report No.: 14120062JMA-002 2 4R PG S  

© Intertek Japan K.K. Page 1 of 67 FJP-TE029 / Effective Date: 23 Jul 2010 TEST REPORT REGULATIONS : FCC Part15 C §15.247 Applicant Testing Laboratory JVC KENWOOD Corporation 1-16-2, Hakusan, Midori-ku, Yokohama-shi Kanagawa, 226-8525 Japan Tel. +81 45 939 6254 Fax.: +81 45 939 7097 Intertek Japan K.K. Matsuda Laboratory (Open area test site) 1283 Yadoriki, Matsuda-machi, Ashigarakami-gun, Kanagawa-ken, 258-0001 Japan Tel.: +81 465 89 2316 Fax.: +81 465 89 2160 (Anechoic chamber) 1386 Yadoriki, Matsuda-machi, Ashigarakami-gun, Kanagawa-ken, 258-0001 Japan Tel.: +81 465 88 4100 Fax.: +81 465 88 4300 URL: http://www.japan.intertek-etlsemko.com Equipment Type REMOTE CONTROL HEAD Trademark KENWOOD Model(s) KCH-20R-M Serial No. No.04 (for Radiated testing) No.02 (for Antenna Port Conductive testing) FCC ID K44473100 Test Result Complied Report Number 14120062JMA-002 Original Issue Date January 21, 2015 This report is for the exclusive use of Intertek's Client and is provided pursuant to the agreement between Intertek and its Client. Intertek's responsibility and liability are limited to the terms and conditions of the agreement. Intertek assumes no liability to any party, other than to the Client in accordance with the agreement, for any loss, expense or damage occasioned by the use of this report. Only the Client is authorized to permit copying or distribution of this report and then only in its entirety. Any use of the Intertek name or one of its marks for the sale or advertisement of the tested material, product or service must first be approved in writing by Intertek. The observations and test results in this report are relevant only to the sample tested. This report by itself does not imply that the material, product, or service is or has ever been under an Intertek certification program. Approved by Tested by Hideaki Kosemura [ Manager ] Shiro Kobayashi [ Engineer ] Report No. : 14120062JMA-002 Original: January 21, 2015 FCC ID: K44473100 © Intertek Japan K.K. Page 2 of 67 FJP-TE029 / Effective Date: 23 Jul 2010 TABLE OF CONTENTS Page SECTION 1. GENERAL INFORMATION ..................................................................................................... 3 SECTION 2. SUMMARY OF TEST RESULTS ............................................................................................ 4 SECTION 3. EQUIPMENT UNDER TEST ................................................................................................... 5 SECTION 4. SUPPORT EQUIPMENT ........................................................................................................ 6 SECTION 5. USED CABLE(S) ..................................................................................................................... 7 SECTION 6. TEST CONFIGURATION ........................................................................................................ 8 SECTION 7. OPERATING CONDITION ...................................................................................................... 9 SECTION 8. UNCERTAINTY ..................................................................................................................... 10 SECTION 9. TEST DATA ............................................................................................................................ 11 9.1 20 dB Bandwidth and 99 % Occupied Bandwidth ............................................................................ 11 9.2 Maximum Peak Output Power ......................................................................................................... 12 9.3 Carrier Frequency Separation ......................................................................................................... 14 9.4 Number of Hopping Frequency ....................................................................................................... 15 9.5 Time of Occupancy .......................................................................................................................... 16 9.6 Radiated Spurious Emissions and Band Edge of Restrict Band ..................................................... 18 9.7 Band Edge of Authorized Frequency Band ..................................................................................... 28 9.8 Spurious RF Conducted Emissions ................................................................................................. 31 9.9 AC Conducted Emissions ................................................................................................................ 32 SECTION 10. LIST AND DIAGRUM OF MEASURING INSTRUMENTS .................................................... 35 ANNEX.................................................................................................................................................. 40 A. HARD COPY OF SPECTRUM PLOTS ............................................................................................. 41 B. PHOTOGRAPHS OF EMISSION SET-UP ....................................................................................... 64 Report No. : 14120062JMA-002 Original: January 21, 2015 FCC ID: K44473100 © Intertek Japan K.K. Page 3 of 67 FJP-TE029 / Effective Date: 23 Jul 2010 SECTION 1. GENERAL INFORMATION Test Performed EUT Received December 12, 2014 Date of Test From December 15 2014 to December 25, 2014 Standard Applied FCC Part15 C §15.247 Test methods ANSI C63.10-2009 ANSI C63.4-2009 Deviation from Standard(s) None Qualifications of Testing Laboratory Accreditation Scope Lab. Code Remarks VLAC EMC Testing VLAC-008-3 JAPAN BSMI EMC Testing SL2-IN-E-6009 TAIWAN Filing VCCI EMC Testing A-0127 JAPAN FCC EMC Testing Designation Number : JP0009 USA IC EMC Testing 2042S-1, 2042S-2, 2042S-3, 2042S-4 Canada CB-Scheme EMC Testing TL223 IECEE SAUDI ARABIA EMC Testing N/A Abbreviations EUT Equipment Under Test DoC Declaration of Conformity AMN Artificial Mains Network ISN Impedance Stabilization Network LISN Line Impedance Stabilization Network Q-P Quasi-…

Text truncated - open the document above for the full version.

Report No. : 14120062JMA-002 Original: January 21, 2015 FCC ID: K44473100 © Intertek Japan K.K. Page 64 of 67 FJP-TE029 / Effective Date: 23 Jul 2010 B. PHOTOGRAPHS OF EMISSION SET-UP Report No. : 14120062JMA-002 Original: January 21, 2015 FCC ID: K44473100 © Intertek Japan K.K. Page 65 of 67 FJP-TE029 / Effective Date: 23 Jul 2010 B.1 Radiated Spurious Emissions below 1 GHz Note : Maintaining 10cm spacing between all the equipment cabinets. Report No. : 14120062JMA-002 Original: January 21, 2015 FCC ID: K44473100 © Intertek Japan K.K. Page 66 of 67 FJP-TE029 / Effective Date: 23 Jul 2010 B.2 Radiated Spurious Emissions above 1 GHz Note : Maintaining 10cm spacing between all the equipment cabinets. Report No. : 14120062JMA-002 Original: January 21, 2015 FCC ID: K44473100 © Intertek Japan K.K. Page 67 of 67 FJP-TE029 / Effective Date: 23 Jul 2010 B.3 AC Conducted Emissions Note : Maintaining 10cm spacing between all the equipment cabinets.