K44501102UHF TRANSCEIVER

WARNING Turn the transceiver power off before entering the following locations:• Near explosives or blasting sites.• In aircrafts. (Any use of the transceiver must follow the instructions and regulations provided by the airline crew.) • Where restrictions or warnings are posted regarding the use of radio devices, including but not limited to medical facilities. • Near persons wearing pacemakers.Turn the transceiver power off before entering the following locations, unless the model is specifically qualified for such use (Intrinsically Safe such as approved by CSA):• In explosive atmospheres (inflammable gas, dust particles, metall ic powders, grain powders, etc.). • While pumping on fuel or while parked at gasoline service stations. CAUTION • Do not disassemble or modify the transceiver for any reason.• Do not place the transceiver on or near airbag equipment while the vehicle is running. When the airbag inflates, the transceiver may beejected and strike the driver or passengers. • Do not transmit while touching the antenna terminal or if any metallic parts are exposed from the antenna covering. Transmitting at such atime may result in a high-frequency burn. • If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, remove the battery packfrom the transceiver, and contact your KENWOOD dealer. • Use of the transceiver while you are driving may be against traffic laws. Please check and observe the vehicle regulations in your area. • Do not expose the transceiver to extremely hot or cold conditions.• Do not carry the battery pack (or battery case) with metal objects, as they may short the battery terminals. • Danger of explosion if the battery is incorrectly replaced; replace on ly with the same type. • When attaching a commercial strap to the transceiver, ensure that the strap is durable. In addition, do not swing the transceiver around bythe strap; you may inadvertently strike and injure another person withthe transceiver. • If a commercially available neck strap is used, take care not to let the strap get caught on nearby machine. • When operating the transceiver in areas where the air is dry, it is easy to build up an electric charge (static electricity). When usingan earphone accessory in such conditions, it is possible for thetransceiver to send an electric shock through the earphone and toyour ear. We recommend you use only a speaker/microphone in theseconditions, to avoid electric shocks. • Do not expose the transceiver to long periods of direct sunlight, nor place it near heating appliances. Information concerning the battery packThe battery pack includes flammable objects such as organic solvent. Mishandling may cause the battery to rupture producing flames or extreme heat, deteriorate, or cause other forms of damage to the battery. Please observe the following prohibitive matters. DANGER • Do not disassemble or reconstruct battery.• Do not short-circuit the battery.• Do not incinerate or apply heat to the battery.• Do not leave the battery near fires, stoves, or other heat generators (areas reaching over 80°C/ 176°F). • Do not immerse the battery in water or get it wet by other means.• Do not charge the battery near fires or under direct sunlight.• Use only the specified charger and observe charging requirements. • Do not pierce the battery with any object, strike it with an instrument, or step on it. • Do not jar or throw the battery.• Do not use the battery pack if it is damaged in any way.• Do not solder directly onto the battery.• Do not reverse the battery polarity (and terminals).• Do not reverse-charge or reverse-connect the battery.• Do not touch a ruptured and leaking battery. If the electrolyte liquid from the battery gets into your eyes, wash youreyes out with fresh water as soon as possible, without rubbing youreyes. Go to the hospital immediately. If left untreated, it may causeeye-problems. WARNING • Do not charge the battery for longer than the specified time.• Do not place the battery pack into a microwave or high pressure container. • Keep ruptured and leaking battery packs away from fire.• Do not use an abnormal battery.• Do not change or charge the battery in hazardous locations. This User guide covers only the basic operations of your radio. For using the detailed instruction manual, refer to the following URL or QR code.https://manual.kenwood.com/files/B5K-0706-00.pdf The AMBE+2 TM voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #8,315,860, #8,595,002, #6,912,495, #8,200,497, #7,970,606, and #8,359,197. Firmware CopyrightsThe title to and ownership of copyrights for firmware embedded in KENWOOD product memories are reserved for JVCKENWOOD Corporation. NOTICES TO THE USER ◆ Government law prohibits the operation of unlicensed radio transmitterswithin the territories under government control. ◆ Illegal operation is punishable by fine and/or imprisonment. ◆ Refer service to qualified technicians only. Safety: It is important that the operator is aware of, and understands, hazards common to the operation of any transceiver. PRECAUTIONS Observe the following precautions to prevent fire, personal injury, and transceiver damage.• Do not charge the transceiver and battery pack when they are wet.• Ensure that there are no metallic items located between the transceive r and the battery pack. • Do not use options not specified by KENWOOD . • If the die-cast chassis or other transceiver part is damaged, do not touch the damaged parts. • If a headset or headp…

Text truncated - open the document above for the full version.

Apr. 27th 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer RE: LETTER OF ATTESTATION FOR MODEL: NX-1300-K4, NX-1200-K5, NX-1300-K6, FCC ID: K44501102. To whom it may concern: This radio meets a spectrum efficiency standard of one voice channel per 6.25 kHz of channel bandwidth and the minimum data rate of 4800 bps in a 6.25 kHz channel. Please contact me if you require any additional information. Sincerely, Tamaki Shimamura Communications Systems Division 1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan

Apr. 27th, 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer RE: LETTER OF AGENT AUTHORIZATION To whom it may concern: We, the undersigned, hereby authorize any individual within HCT Co.,Ltd. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C.862. This agreement expires one year from the current date. Sincerely, Tamaki Shimamura Communications Systems Division 1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan

Apr. 27th 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer RE: CONFIDENTIALITY REQUEST FOR MODEL: NX-1300-K4, NX-1300-K5, NX-1300-K6, FCC ID: K44501102 To whom it may concern: This letter serves as an official request for permanent confidentiality pursuant to 47 CFR Section 0.459 of the Commission Rules. We have requested that the Block Diagram, Schematic Diagrams, Circuit Description, Parts List, Active Devices and Tuning Procedure required to be submitted with this application be withheld from public review. The documents are company proprietary information that could never get into the possession of our competition. Please contact me if you require any additional information. Sincerely, Tamaki Shimamura Communications Systems Division 1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan

1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan Apr. 27th, 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer Subject: Justify Extended Frequency Range for MODEL: NX-1300-K4, NX-1300-K5, NX-1300-K6 FCC ID: K44501102 To Whom It May Concern: This letter serves justification for extended frequencies This device has design capability to operate in the frequency band 406.1 to 470 MHz and complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Please note that Licensed End Users do not have access to any external controls that will allow them to program the equipment. Equipment programming is the responsibility of KENWOOD approved Service Agents. In addition to Parts 90/22/74 usage, this device is utilized in systems such as Federal and Public Safety agencies, e.g. police, fire, and emergency medical, etc. as indicated in the following table: Table 1 – Frequency Range and Rule Parts - (47 CFR Part 2.106) It is understood that a grant note code may be added to the grant which indicates this required operation. In addition, we acknowledge that it is a violation of FCC rules if the device operates on unauthorized frequencies. Please contact me if you require any additional information. Sincerely, Tamaki Shimamura Communications Systems Division Freq. Range (MHz) Part 90 Part 22 Part 74 Federal Customers 406.1000-450.0000 x 450.0000-454.0000 x x 454.0000-455.0000 x 455.0000-456.0000 x 456.0000-460.0000 x x 460.0000-462.5375 x 462.5375-462.7375 x 462.7375-467.5375 x 467.5375-467.7375 x 467.7375-470.0000 x

FCC ID: K44501102 IC: 282F-501102 Difference between the NX-1300-K6, NX-1300-K5, NX-1300-K4. There is no difference in the radio unit. Therefore, it does not affect the test results. The difference point is number of key, LCD. Model Name HVIN Differential Basic Model NX-1300-K6 NX-1300-K6-21 16Key with LCD Additional Model NX-1300-K5 NX-1300-K5-21 7Key with LCD Additional Model NX-1300-K4 NX-1300-K4-21 Non key, non LCD <Key Type> NX-1300-K6 NX-1300-K5 NX-1300-K4 Tamaki Shimamura Communications Systems Division JVC KENWOOD Corporation

FCC ID: K44501102, IC: 282F-501102 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page １ of 3 EXTERNAL PHOTOGRAPHS FCC ID: K44501102, IC: 282F-501102 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page ２ of 3 ■ EXTERNAL PHOTO FCC ID: K44501102, IC: 282F-501102 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page ３ of 3 ■ EXTERNAL PHOTO

FCC ID: K44501102 IC: 282F-501102 Front View of NX-1300-K6 Front View of NX-1300-K5 Front View of NX-1300-K4 Rear View FCC ID: K44501102 IC: 282F-501102 Side View Side View Top View Bottom View

FCC ID: K44501102 IC: 282F-501102 NX-1300-K6 NX-1300-K5 NX-1300-K4

FCC ID: K44501102, IC: 282F-501102 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page １ of 4 INTERNAL PHOTOGRAPHS FCC ID: K44501102, IC: 282F-501102 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page ２ of 4 ■ INTERNAL PHOTO FCC ID: K44501102, IC: 282F-501102 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page ３ of 4 ■ INTERNAL PHOTO FCC ID: K44501102, IC: 282F-501102 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page ４ of 4 ■ INTERNAL PHOTO

FCC ID: K44501102 IC: 282F-501102 NX-1300-K6 NX-1300-K5 NX-1300-K4 FCC ID: K44501102 IC: 282F-501102 NX-1300-K6 NX-1300-K5 FCC ID: K44501102 IC: 282F-501102 NX-1300-K4 NX-1300-K4, NX-1300-K5, NC-1300-K6

TEST REPORT FCC/ISED Test for NX-1300-K6 APPLICANT JVCKENWOOD Corporation REPORT NO. HCT-RF-2105-FI001 DATE OF ISSUE May 14, 2021 Tested by Kwon Jeong Technical Manager Jong Seok Lee F-TP22-03(Rev.03) HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383 KOREA Tel. +82 31 634 6300 F ax. +82 31 645 6401 1 / 195 F-TP22-03 (Rev. 03) Page 2 of 195 HCT Co., Ltd. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383 KOREA Tel. +82 31 634 6300 Fax. +82 31 645 6401 TEST REPORT FCC/ISED Test for NX-1300-K6 REPORT NO. HCT-RF-2105-FI001 DATE OF ISSUE May 14, 2021 Additional Model(s) NX-1300-K4, NX-1300-K5 Applicant JVCKENWOOD Corporation 1-16-2 Hakusan Midori-ku Yokohama-shi Kanagawa 226-8525 Japan Product Name UHF TRANSCEIVER Model(s) NX-1300-K6 FCC ID IC K44501102 282F-501102 Test Standard Used Part 2, 22, 74, 90 / RSS- Gen Issue 5, RSS-119 Issue 12 Frequency Range FCC: 406.1 MHz ~ 470.0 MHz ISED: 406.1 ~ 430.0 MHz, 450.0 ~ 470.0 MHz The result shown in this test report refer only to the sample(s) tested unless otherwise stated. This test results were applied only to the test methods required by the standard. F-TP22-03 (Rev. 03) Page 3 of 195 Report No. HCT-RF-2105-FI001 REVISION HISTORY The revision history for this test report is shown in table. Revision No. Date of Issue Description 0 May 14, 2021 Initial Release The measurements shown in this report were made in accordance with the procedures specified in §2.947. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. HCT CO., LTD. Certifies that no party to this application has subject to a denial of Federal benefits that includes FCC benefits pursuant to section 5301 of the Anti-Drug Abuse Act of 1998,21 U.S. C.853(a) * The report shall not be reproduced except in full(only partly) without approval of the laboratory. F-TP22-03 (Rev. 03) Page 4 of 195 Report No. HCT-RF-2105-FI001 CONTENTS 1. GENERAL INFORMATION 5 2. EUT DESCRIPTION 6 3. TEST METHODOLOGY 8 3.1 EUT CONFIGURATION 8 3.2 EUT EXERCISE 8 3.3 GENERAL TEST PROCEDURES 8 3.4 DESCRIPTION OF TEST MODES 9 4. INSTRUMENT CALIBRATION 9 5. FACILITIES AND ACCREDITATIONS 9 5.1 FACILITIES 9 5.2 EQUIPMENT 9 6. WORST CASE CONFIGURATION AND MODE 10 7. SUMMARY TEST OF RESULTS 11 8. TEST RESULT 15 8.1 Carrier Output Power 15 8.2 Carrier Frequency Stability 18 8.3 Occupied Bandwidth 31 8.4 Modulation Limiting 57 8.5 Audio Frequency Response / Audio Low Pass Filter Response 74 8.6 Emission Mask 100 8.7 Transient Frequency Behavior 126 8.8 Unwanted Emissions : Conducted Spurious Emission 146 8.9 Unwanted Emissions : Radiated Spurious Emission 187 8.10 Unwanted Emissions : Receiver Radiated Spurious Emission 192 8.11 Necessary Bandwidth Calculations 193 9. LIST OF TEST EQUIPMENT 194 10. ANNEX A_ TEST SETUP PHOTO 195 F-TP22-03 (Rev. 03) Page 5 of 195 Report No. HCT-RF-2105-FI001 1. GENERAL INFORMATION Manufacturer: JVCKENWOOD Corporation Address: 1-16-2 Hakusan Midori-ku Yokohama-shi Kanagawa 226-8525 Japan FCC ID: K44501102 ISED: 282F-501102 EUT Type: UHF TRANSCEIVER Model(s): NX-1300-K6 Additional Model(s): NX-1300-K4, NX-1300-K5 Date(s) of Tests: April 16, 2021 ~ May 12, 2021 Place of Tests: HCT Co., Ltd. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA F-TP22-03 (Rev. 03) Page 6 of 195 Report No. HCT-RF-2105-FI001 2. EUT DESCRIPTION Power Supply Voltage DC 7.5V ± 20% Output Power 5 W (Power output continuously variable to 0.25 W) (Max : 5.2 W) Battery type KNB-45L Li-Ion Battery Pack (2000mA) KNB-53N Ni-MH Battery Pack (1400mA) KNB-29N Ni-MH Battery Pack (1500mA) KNB-69L Li-ion Battery Pack (2450mA) KNB-82LC (Li-ion Battery Pack) KNB-84L Li-Ion Battery Pack (2000mA) Antenna KRA-23M UHF Low Profile Helical Antenna (440-490 MHz) KRA-23M3 UHF Low Profile Helical Antenna (400-450 MHz) KRA-27M UHF Whip Antenna (440-490 MHz) KRA-27M3 UHF Whip Antenna (400-450 MHz) KRA-42M UHF Stubby Antenna (440-490 MHz) KRA-42M3 UHF Stubby Antenna (400-450 MHz) Peak Antenna gain KRA-23M UHF Low Profile Helical Antenna: 0 dBd KRA-23M3 UHF Low Profile Helical Antenna: 0 dBd KRA-27M UHF Whip Antenna: 0 dBd KRA-27M3 UHF Whip Antenna: 0 dBd KRA-42M UHF Stubby Antenna: 0 dBd KRA-42M3 UHF Stubby Antenna: 0 dBd Type of Emission 16K0F3E: Analogue (*16K0F3E is ISED only) 11K0F3E: Analogue 8K30F1E, 8K30F1D, 8K30F7W: NXDN 7K60FXE, 7K60FXD: DMR 4K00F1E, 4K00F1D, 4K00F7W: NXDN 4K00F2D: CWID Channel Bandwidth 25 kHz* / 6.25 kHz / 12.5 kHz (*25kHz is ISED only) Operating Temperature -30 (ᄌ) ~ +60 (ᄌ) Frequency Range 406.1 MHz ~ 470.0 MHz (FCC) 406.1 ~ 430.0 MHz, 450.0 ~ 470.0 MHz (ISED) Test Frequency 406.15 MHz / 429.95 MHz / 469.95 MHz F-TP22-03 (Rev. 03) Page 7 of 195 Report No. HCT-RF-2105-FI001 Maximum deviation 16K0F3E: ± 5 kHz 11K0F3E: ± 2.5 kHz Frequency Stability ± 1.0 ppm PMN NX-1300-K4, NX-1300-K5, NX-1300-K6 HVIN NX-1300-K4-21, NX-1300-K5-21, NX-1300-K6-21 FVIN N/A HMN N/A F-TP22-03 (Rev. 03) Page 8 of 195 Report No. HCT-RF-2105-FI001 3. TEST METHODOLOGY TIA-603-E dated March 2016 entitled ᄲLand Mobile FM or PM Communications Equipment Measurement and Performance Standardsᄶ were used in the measurement. 3.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the Tx frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the FCC Rules Part 2 and Part 90. 3.3 GENERAL TEST PROCEDURES Radiated Emissions Radiated emission measurements are performed in the Fully-anechoic chamber. The equipment under test is placed on a non-conductive table 3-meters away from the receive antenna in accordance with ANSI/TIA-603-E-2016. T…

Text truncated - open the document above for the full version.

F-TP22-03 (Rev. 03) Page 160 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 161 of 195 Report No. HCT-RF-2105-FI001 (469.95 MHz)_High 9 kHz~150 kHz 150 kHz~30 MHz F-TP22-03 (Rev. 03) Page 162 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 163 of 195 Report No. HCT-RF-2105-FI001 8K30F1E, 8K30F1D, 8K30F7W_FCC/ISED (406.15 MHz)_High 9 kHz~150 kHz 150 kHz~30 MHz F-TP22-03 (Rev. 03) Page 164 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 165 of 195 Report No. HCT-RF-2105-FI001 (429.95 MHz)_High 9 kHz~150 kHz 150 kHz~30 MHz F-TP22-03 (Rev. 03) Page 166 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 167 of 195 Report No. HCT-RF-2105-FI001 (469.95 MHz)_High 9 kHz~150 kHz 150 kHz~30 MHz F-TP22-03 (Rev. 03) Page 168 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 169 of 195 Report No. HCT-RF-2105-FI001 7K60FXD, 7K60FXE_FCC/ISED (406.15 MHz)_High 9 kHz~150 kHz 150 kHz~30 MHz F-TP22-03 (Rev. 03) Page 170 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 171 of 195 Report No. HCT-RF-2105-FI001 (429.95 MHz)_High 9 kHz~150 kHz 150 kHz~30 MHz F-TP22-03 (Rev. 03) Page 172 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 173 of 195 Report No. HCT-RF-2105-FI001 (469.95 MHz)_High 9 kHz~150 kHz 150 kHz~30 MHz F-TP22-03 (Rev. 03) Page 174 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 175 of 195 Report No. HCT-RF-2105-FI001 4K00F1E, 4K00F1D, 4K00F7W_FCC/ISED (406.15 MHz)_High 9 kHz~150 kHz 150 kHz~30 MHz F-TP22-03 (Rev. 03) Page 176 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 177 of 195 Report No. HCT-RF-2105-FI001 (429.95 MHz)_High 9 kHz~150 kHz 150 kHz~30 MHz F-TP22-03 (Rev. 03) Page 178 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 179 of 195 Report No. HCT-RF-2105-FI001 (469.95 MHz)_High 9 kHz~150 kHz 150 kHz~30 MHz F-TP22-03 (Rev. 03) Page 180 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 181 of 195 Report No. HCT-RF-2105-FI001 4K00F2D_FCC/ISED (406.15 MHz)_High 9 kHz~150 kHz 150 kHz~30 MHz F-TP22-03 (Rev. 03) Page 182 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 183 of 195 Report No. HCT-RF-2105-FI001 (429.95 MHz)_High 9 kHz~150 kHz 150 kHz~30 MHz F-TP22-03 (Rev. 03) Page 184 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 185 of 195 Report No. HCT-RF-2105-FI001 (469.95 MHz)_High 9 kHz~150 kHz 150 kHz~30 MHz F-TP22-03 (Rev. 03) Page 186 of 195 Report No. HCT-RF-2105-FI001 30 MHz~1 GHz 1 GHz~10 GHz F-TP22-03 (Rev. 03) Page 187 of 195 Report No. HCT-RF-2105-FI001 8.9 Unwanted Emissions : Radiated Spurious Emission 굃 Definition Radiated spurious emissions are emissions from the equipment when transmitting into a non-radiating load on a frequency or frequencies that are outside an occupied band sufficient to ensure transmission of information of required quality for the class of communications desired. 굃 TEST CONFIGURATION Below 30 MHz Above 1 GHz F-TP22-03 (Rev. 03) Page 188 of 195 Report No. HCT-RF-2105-FI001 TEST PROCEDURE USED Radiated tests are performed in the Fully-anechoic chamber. Radiated Spurious Emission Measurements at 3 meters by Substitution Method according to ANSI/TIA-603E-2016. a) The Resolution Bandwidth for scanning Radiated Emission below 1 GHz is 100 kHz with Video Bandwidth = 300 kHz and Resolution Bandwidth for above 1 GHz is 1 MHz with Video Bandwidth = 3 MHz. b) Detector mode is peak. c) In the fully-anechoic chamber, setup as illustrated above the DUT placed on the 2.5m height of Turn Table, rotated the table around 360 degrees to search the maximum radiation power and receiver antenna shall be rotated vertical and horizontal polarization. The ᄲRead Valueᄶ is the spectrum reading the maximum power value. d) The substitution antenna is substituted for DUT at the same position and signals generator (S.G) export the CW signal to the substitution antenna via a TX cable. The receiver antenna shall be rotated vertical and horizontal polarization to find the maximum radiation power. Record the power level of maximum radiation power from spectrum. So, the measured Factor value = Ref level of S.G + TX cables loss ᄧ Substituted Antenna Gain. 4) Result(dBm) = ᄲReadingᄶ + Factor F-TP22-03 (Rev. 03) Page 189 of 195 Report No. HCT-RF-2105-FI001 굃 TEST RESULTS 16K0F3E Test Frequency (MHz) Measured Frequency (MHz) Pol Reading (dBm) Factor (dB) Result (dBm) Limit (dBm) Margin (dB) 406.15 812.30 H -86.87 39.57 -47.31 -13.00 34.31 1218.45 V -69.97 34.38 -35.59 -13.00 22.59 2030.75 V -72.62 35.85 -36.77 -13.00 23.77 Test Frequency (MHz) Measured Frequency (MHz) Pol Reading (dBm) Factor (dB) Result (dBm) Limit (dBm) Margin (dB) 429.95 859.90 H -86.42 39.63 -46.79 -13.00 33.79 1289.85 V -70.77 34.66 -36.11 -13.00 23.11 2149.75 V -74.28 37.90 -36.38 -13.00 23.38 Test Frequency (MHz) Measured Frequency (MHz) Pol Reading (dBm) Factor (dB) Result (dBm) Limit (dBm) Margin (dB) 469.95 939.90 H -80.21 41.23 -38.98 -13.00 25.98 1409.85 V -68.06 34.67 -33.39 -13.00 20.39 3289.65 V -72.27 39.40 -32.87 -13.00 19.87 4699.50 V -71.93 43.65 -28.28 -13.00 15.28 F-TP22-03 (Rev. 03) Page 190 of 195 Report No. HCT-RF-2105-FI001 7K60FXD, 7K60FXE Test Frequency (MHz) Measured Frequency (MHz) Pol Reading (dBm) Factor (dB) Result (dBm) Limit (dBm) Margin (dB) 406.15 812.30 H -86.57 39.57 -47.01 -20.00 27.01 1218.45 V -72.17 34.38 -37.79 -20.00 17.79 2030.75 V -69.97 35.85 -34.12 -20.00 14.12 Test Frequency (MHz) Measured Frequency (MHz) Pol Reading (dBm) Factor (dB) Result (dBm) Limit (dBm) Margin (dB) 429.95 859.90 H -86.55 39.63 -46.92 -20.00 26.92 1289.85 V -69.94 34.66 -35.28 -20.00 15.28 2149.75 V -74.24 37.9…

Text truncated - open the document above for the full version.

Page 1 of 55 HCT Co., Ltd. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383 KOREA Tel. +82 31 645 6300 F ax. +82 31 645 6401 On your side F-TP22-03 (Rev. 03) TEST REPORT FCC SAR Test for certification of K44501102 APPLICANT JVCKENWOOD Corporation REPORT NO. HCT-SR-2105-FC002 DATE OF ISSUE May. 14, 2021 Tested by Yoon Ho Choi (signaure) Technical Manager Yun Jeang Heo (signature) F-TP22-03 (Rev. 03) Page 2 of 55 HCT Co., Ltd. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383 KOREA Tel. +82 31 634 6300 Fax. +82 31 645 6401 TE S T R E P O R T F C C S A R T e s t f o r c e r t i f i c a t i o n REPORT NO. HCT-SR-2105-FC002 DATE OF ISSUE May. 14, 2021 Applicant JVCKENWOOD Corporation 1-16-2 Hakusan Midori-ku Yokohama-shi Kanagawa 226-8525 Japan Equipment Type Model Name UHF TRANSCEIVER NX-1300-K4, NX-1300-K5, NX-1300-K6 FCC ID K44501102 Date of Test Apr. 12, 2021 ~ Apr. 13, 2021 FCC Rule Part(s) CFR §2.1093 This device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in FCC KDB procedures and had been tested in accordance with the measurement procedures specified in FCC KDB procedures. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. The result shown in this test report refer only to the sample(s) tested unless otherwise stated. This test results were applied only to the test methods required by the standard. F-TP22-03 (Rev. 03) Page 3 of 55 Report No HCT-SR-2105-FC002 REVISION HISTORY The revision history for this test report is shown in table. Revision No. Date of Issue Description 0 May. 14, 2021 Initial Release F-TP22-03 (Rev. 03) Page 4 of 55 Report No HCT-SR-2105-FC002 CONTENTS 1. Test Regulations ......................................................................................................................................................................... 5 2. Test Location ............................................................................................................................................................................... 5 3. Information of the EUT ............................................................................................................................................................ 6 4. Output Power Specifications .................................................................................................................................................. 8 5. Manufacturer’s Accessory List ............................................................................................................................................... 8 6. Introduction ............................................................................................................................................................................... 12 7. Description of test equipment ............................................................................................................................................. 13 8. SAR Measurement Procedure .............................................................................................................................................. 16 9. Description of Test Position.................................................................................................................................................. 18 10. RF Exposure Limits ................................................................................................................................................................. 20 11. System Verification................................................................................................................................................................. 21 12. SAR Test Data Summary ...................................................................................................................................................... 22 13. Measurement Uncertainty ................................................................................................................................................... 25 14. SAR Test Equipment ............................................................................................................................................................. 26 15. Conclusion ............................................................................................................................................................................... 27 16. References................................................................................................................................................................................ 28 Attachment 1. – SAR Test Plots ................................................................................................................................................ 30 Attachment 2. – Dipole Verification Plots ............................................................................................................................. 32 Attachment 3. – SAR Tissue Characterization ..................................................................…

Text truncated - open the document above for the full version.