K44501103UHF TRANSCEIVER

WARNING Turn the transceiver power off before entering the following locations:• Near explosives or blasting sites.• In aircrafts. (Any use of the transceiver must follow the instructions and regulations provided by the airline crew.) • Where restrictions or warnings are posted regarding the use of radio devices, including but not limited to medical facilities. • Near persons wearing pacemakers.Turn the transceiver power off before entering the following locations, unless the model is specifically qualified for such use (Intrinsically Safe such as approved by CSA):• In explosive atmospheres (inflammable gas, dust particles, metall ic powders, grain powders, etc.). • While pumping on fuel or while parked at gasoline service stations. CAUTION • Do not disassemble or modify the transceiver for any reason.• Do not place the transceiver on or near airbag equipment while the vehicle is running. When the airbag inflates, the transceiver may beejected and strike the driver or passengers. • Do not transmit while touching the antenna terminal or if any metallic parts are exposed from the antenna covering. Transmitting at such atime may result in a high-frequency burn. • If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, remove the battery packfrom the transceiver, and contact your KENWOOD dealer. • Use of the transceiver while you are driving may be against traffic laws. Please check and observe the vehicle regulations in your area. • Do not expose the transceiver to extremely hot or cold conditions.• Do not carry the battery pack (or battery case) with metal objects, as they may short the battery terminals. • Danger of explosion if the battery is incorrectly replaced; replace on ly with the same type. • When attaching a commercial strap to the transceiver, ensure that the strap is durable. In addition, do not swing the transceiver around bythe strap; you may inadvertently strike and injure another person withthe transceiver. • If a commercially available neck strap is used, take care not to let the strap get caught on nearby machine. • When operating the transceiver in areas where the air is dry, it is easy to build up an electric charge (static electricity). When usingan earphone accessory in such conditions, it is possible for thetransceiver to send an electric shock through the earphone and toyour ear. We recommend you use only a speaker/microphone in theseconditions, to avoid electric shocks. • Do not expose the transceiver to long periods of direct sunlight, nor place it near heating appliances. Information concerning the battery packThe battery pack includes flammable objects such as organic solvent. Mishandling may cause the battery to rupture producing flames or extreme heat, deteriorate, or cause other forms of damage to the battery. Please observe the following prohibitive matters. DANGER • Do not disassemble or reconstruct battery.• Do not short-circuit the battery.• Do not incinerate or apply heat to the battery.• Do not leave the battery near fires, stoves, or other heat generators (areas reaching over 80°C/ 176°F). • Do not immerse the battery in water or get it wet by other means.• Do not charge the battery near fires or under direct sunlight.• Use only the specified charger and observe charging requirements. • Do not pierce the battery with any object, strike it with an instrument, or step on it. • Do not jar or throw the battery.• Do not use the battery pack if it is damaged in any way.• Do not solder directly onto the battery.• Do not reverse the battery polarity (and terminals).• Do not reverse-charge or reverse-connect the battery.• Do not touch a ruptured and leaking battery. If the electrolyte liquid from the battery gets into your eyes, wash youreyes out with fresh water as soon as possible, without rubbing youreyes. Go to the hospital immediately. If left untreated, it may causeeye-problems. WARNING • Do not charge the battery for longer than the specified time.• Do not place the battery pack into a microwave or high pressure container. • Keep ruptured and leaking battery packs away from fire.• Do not use an abnormal battery.• Do not change or charge the battery in hazardous locations. This User guide covers only the basic operations of your radio. For using the detailed instruction manual, refer to the following URL or QR code.https://manual.kenwood.com/files/B5K-0706-00.pdf The AMBE+2 TM voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #8,315,860, #8,595,002, #6,912,495, #8,200,497, #7,970,606, and #8,359,197. Firmware CopyrightsThe title to and ownership of copyrights for firmware embedded in KENWOOD product memories are reserved for JVCKENWOOD Corporation. NOTICES TO THE USER ◆ Government law prohibits the operation of unlicensed radio transmitterswithin the territories under government control. ◆ Illegal operation is punishable by fine and/or imprisonment. ◆ Refer service to qualified technicians only. Safety: It is important that the operator is aware of, and understands, hazards common to the operation of any transceiver. PRECAUTIONS Observe the following precautions to prevent fire, personal injury, and transceiver damage.• Do not charge the transceiver and battery pack when they are wet.• Ensure that there are no metallic items located between the transceive r and the battery pack. • Do not use options not specified by KENWOOD . • If the die-cast chassis or other transceiver part is damaged, do not touch the damaged parts. • If a headset or headp…

Text truncated - open the document above for the full version.

Apr. 27th 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer RE: LETTER OF ATTESTATION FOR MODEL: NX-1300-K, NX-1300-K2, NX-1300-K3, NX-1302-K FCC ID: K44501103 To whom it may concern: This radio meets a spectrum efficiency standard of one voice channel per 6.25 kHz of channel bandwidth and the minimum data rate of 4800 bps in a 6.25 kHz channel. Please contact me if you require any additional information. Sincerely, Tamaki Shimamura Communications Systems Division 1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan

Apr. 27th, 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer RE: LETTER OF AGENT AUTHORIZATION To whom it may concern: We, the undersigned, hereby authorize any individual within HCT Co.,Ltd. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C.862. This agreement expires one year from the current date. Sincerely, Tamaki Shimamura Communications Systems Division 1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan

Apr. 27th 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer RE: CONFIDENTIALITY REQUEST FOR MODEL: NX-1300-K, NX-1300-K2, NX-1300-K3, NX-1302-K, FCC ID: K44501103 To whom it may concern: This letter serves as an official request for permanent confidentiality pursuant to 47 CFR Section 0.459 of the Commission Rules. We have requested that the Block Diagram, Schematic Diagrams, Circuit Description, Parts List, Active Devices and Tuning Procedure required to be submitted with this application be withheld from public review. The documents are company proprietary information that could never get into the possession of our competition. Please contact me if you require any additional information. Sincerely, Tamaki Shimamura Communications Systems Division 1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan

1-16-2, Hakusan, Midori-ku, Yokohama-shi, Kanagawa, 226-8525 Japan Apr. 27th, 2021 Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Attn: Reviewing Engineer Subject: Justify Extended Frequency Range for MODEL: NX-1300-K, NX-1300-K2, NX-1300-K3, NX-1302-K FCC ID: K44501103 To Whom It May Concern: This letter serves justification for extended frequencies This device has design capability to operate in the frequency band 450 to 512 MHz and complies with 47 CFR Part 90.203(e), in that the operator cannot directly program the transmit frequencies using the normally accessible external controls. Please note that Licensed End Users do not have access to any external controls that will allow them to program the equipment. Equipment programming is the responsibility of KENWOOD approved Service Agents. In addition to Parts 90/22/74 usage, this device is utilized in systems such as Federal and Public Safety agencies, e.g. police, fire, and emergency medical, etc. as indicated in the following table: Table 1 – Frequency Range and Rule Parts - (47 CFR Part 2.106) It is understood that a grant note code may be added to the grant which indicates this required operation. In addition, we acknowledge that it is a violation of FCC rules if the device operates on unauthorized frequencies. Please contact me if you require any additional information. Sincerely, Tamaki Shimamura Communications Systems Division Freq. Range (MHz) Part 90 Part 22 Part 74 Federal Customers 450.0000-454.0000 x x 454.0000-455.0000 x 455.0000-456.0000 x 456.0000-460.0000 x x 460.0000-462.5375 x 462.5375-462.7375 x 462.7375-467.5375 x 467.5375-467.7375 x 467.7375-470.0000 x 470.0000-512.0000 x x x

FCC ID: K4450110 3 Difference between the NX-1300-K3, NX-1300-K2, NX-1300-K, NX-1302-K There is no difference in the radio unit. Therefore, it does not affect the test results. The difference point is number of key, LCD. Model(HVIN) Differential Basic model NX-1300-K3 16 key with LCD Additional model NX-1300-K2 7 key with LCD Additional model NX-1300-K Non key and non LCD Additional model NX-1302-K Same as NX-1300-K <Key type> Basic Additional Additional NX-1300-K 3 NX-1300-K2 NX-1300-K, NX-1302-K Tamaki Shimamura Communications Systems Division JVCKENWOOD Corporation

FCC ID: K44501103 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page １ of 3 EXTERNAL PHOTOGRAPHS FCC ID: K44501103 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page ２ of 3 ■ EXTERNAL PHOTO FCC ID: K44501103 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page ３ of 3 ■ EXTERNAL PHOTO

FCC ID: K44501103 NX-1300-K NX-1300-K2 NX-1300-K3 NX-1302-K

FCC ID: K44501103 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page １ of 4 INTERNAL PHOTOGRAPHS FCC ID: K44501103 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page ２ of 4 ■ INTERNAL PHOTO FCC ID: K44501103 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page ３ of 4 ■ INTERNAL PHOTO FCC ID: K44501103 HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA TEL : + 82 31 645 6300 FAX : + 82 31 645 6401 www.hct.co.kr Page ４ of 4 ■ INTERNAL PHOTO

Page 1 of 55 HCT Co., Ltd. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383 KOREA Tel. +82 31 645 6300 F ax. +82 31 645 6401 On your side F-TP22-03 (Rev. 03) TEST REPORT FCC SAR Test for certification of K44501103 APPLICANT JVCKENWOOD Corporation REPORT NO. HCT-SR-2105-FC001 DATE OF ISSUE May. 14, 2021 Tested by Yoon Ho Choi (signaure) Technical Manager Yun Jeang Heo (signature) F-TP22-03 (Rev. 03) Page 2 of 55 Page 2 of 55 HCT Co., Ltd. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383 KOREA Tel. +82 31 634 6300 Fax. +82 31 645 6401 TE S T R E P O R T F C C S A R T e s t f o r c e r t i f i c a t i o n REPORT NO. HCT-SR-2105-FC001 DATE OF ISSUE May. 14, 2021 Applicant JVCKENWOOD Corporation 1-16-2 Hakusan Midori-ku Yokohama-shi Kanagawa 226-8525 Japan Equipment Type Model Name UHF TRANSCEIVER NX-1300-K2, NX-1300-K, NX-1300-K3, NX-1302-K FCC ID K44501103 Date of Test Apr. 08, 2021 ~ Apr. 09, 2021 FCC Rule Part(s) CFR §2.1093 This device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in FCC KDB procedures and had been tested in accordance with the measurement procedures specified in FCC KDB procedures. I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. The result shown in this test report refer only to the sample(s) tested unless otherwise stated. This test results were applied only to the test methods required by the standard. F-TP22-03 (Rev. 03) Page 3 of 55 Page 3 of 55 Report No. HCT-SR-2105-FC001 REVISION HISTORY The revision history for this test report is shown in table. Revision No. Date of Issue Description 0 May 14, 2021 Initial Release F-TP22-03 (Rev. 03) Page 4 of 55 Page 4 of 55 Report No. HCT-SR-2105-FC001 CONTENTS 1. Test Regulations ......................................................................................................................................................................... 5 2. Test Location ............................................................................................................................................................................... 5 3. Information of the EUT ............................................................................................................................................................ 6 4. Output Power Specifications .................................................................................................................................................. 8 5. Manufacturer’s Accessory List ............................................................................................................................................... 9 6. Introduction ............................................................................................................................................................................... 12 7. Description of test equipment ............................................................................................................................................. 13 8. SAR Measurement Procedure .............................................................................................................................................. 16 9. Description of Test Position.................................................................................................................................................. 18 10. RF Exposure Limits ................................................................................................................................................................. 20 11. System Verification................................................................................................................................................................. 21 12. SAR Test Data Summary ...................................................................................................................................................... 23 13. Measurement Uncertainty ................................................................................................................................................... 26 14. SAR Test Equipment ............................................................................................................................................................. 27 15. Conclusion ............................................................................................................................................................................... 28 16. References................................................................................................................................................................................ 29 Attachment 1. – SAR Test Plots ................................................................................................................................................ 31 Attachment 2. – Dipole Verification Plots ............................................................................................................................. 32 Attachment 3. – SAR Tissue Characterization ...................................................................................................................... 37 Attachment 4. – SAR System Validation ................................................................................................................................ 38 Attachment 5. – Probe Calibration Data ............................................................................................................................... 39 Attachment 6. – Dipole Calibration Data .........................................................…

Text truncated - open the document above for the full version.

File No. HCT-SR-2105-FC001-P Page 1 of 16 HCT Co., Ltd. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383 KOREA Tel. +82 31 634 6300 Fax. +82 31 645 6401 A p p e n d i x A: T e s t S e t u p P h o t o FCC ID. K44501103 File No. HCT-SR-2105-FC001-P REVISION HISTORY The revision history for this document is shown in table. Revision No. Date of Issue Description 0 May 14, 2021 Initial Release File No. HCT-SR-2105-FC001-P Page 2 of 16 FCC ID. K44501103 1. Hand-held to Face 1.1 Test Setup Photo (Hand-held to Face) All File No. HCT-SR-2105-FC001-P Page 3 of 16 FCC ID. K44501103 1.2 Test Setup Photo (Hand-held to Face) All - KMC-48GPS File No. HCT-SR-2105-FC001-P Page 4 of 16 FCC ID. K44501103 1.3 Test Setup Photo (Hand-held to Face) Distance of 25 mm from the EUT File No. HCT-SR-2105-FC001-P Page 5 of 16 FCC ID. K44501103 1.4 Test Setup Photo (Hand-held to Face) - KMC-48GPS Distance of 25 mm from the EUT File No. HCT-SR-2105-FC001-P Page 6 of 16 FCC ID. K44501103 2. Body-worn Belt clip 2.1 Test Setup Photo (Body-worn Belt clip) All File No. HCT-SR-2105-FC001-P Page 7 of 16 FCC ID. K44501103 2.2 Test Setup Photo (Body-worn Belt clip) All - KMC-48GPS File No. HCT-SR-2105-FC001-P Page 8 of 16 FCC ID. K44501103 2.3 Test Setup Photo (Body-worn Belt clip) Distance of 0 mm from the EUT File No. HCT-SR-2105-FC001-P Page 9 of 16 FCC ID. K44501103 2.4 Test Setup Photo (Body-worn Belt clip) - KMC-48GPS Distance of 0 mm from the EUT File No. HCT-SR-2105-FC001-P Page 10 of 16 FCC ID. K44501103 3. DUT 3.1 DUT File No. HCT-SR-2105-FC001-P Page 11 of 16 FCC ID. K44501103 3.2 DUT File No. HCT-SR-2105-FC001-P Page 12 of 16 FCC ID. K44501103 3.3 Antenna File No. HCT-SR-2105-FC001-P Page 13 of 16 FCC ID. K44501103 3.4 Antenna File No. HCT-SR-2105-FC001-P Page 14 of 16 FCC ID. K44501103 3.5 Battery File No. HCT-SR-2105-FC001-P Page 15 of 16 FCC ID. K44501103 3.6 Accessory (KBH-10) File No. HCT-SR-2105-FC001-P Page 16 of 16 FCC ID. K44501103 3.7 Accessory (KMC-48GPS)

TEST REPORT FCC Test for NX-1300-K3 Certification APPLICANT JVCKENWOOD Corporation REPORT NO. HCT-RF-2105-FC002 DATE OF ISSUE May 14, 2021 Tested by Kwon Jeong Technical Manager Jong Seok Lee F-TP22-03(Rev.03) HCT CO., LTD. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383 KOREA Tel. +82 31 634 6300 F ax. +82 31 645 6401 1 / 250 F-TP22-03 (Rev. 03) Page 2 of 250 HCT Co., Ltd. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383 KOREA Tel. +82 31 634 6300 Fax. +82 31 645 6401 TEST REPORT FCC Test for NX-1300-K3 REPORT NO. HCT-RF-2105-FC002 DATE OF ISSUE May 14, 2021 Additional Model(s) N X-1300-K, NX-1300-K2, NX-1302-K Applicant JVCKENWOOD Corporation 1-16-2 Hakusan Midori-ku Yokohama-shi Kanagawa 226-8525 Japan Product Name UHF TRANSCEIVER Model(s) NX-1300-K3 FCC ID K44501103 Test Standard Used Part 2, 22, 74, 90 Frequency Range 450 MHz ~ 512 MHz The result shown in this test report refer only to the sample(s) tested unless otherwise stated. This test results were applied only to the test methods required by the standard. F-TP22-03 (Rev. 03) Page 3 of 250 Report No. HCT-RF-2105-FC002 REVISION HISTORY The revision history for this test report is shown in table. Revision No. Date of Issue Description 0 May 14, 2021 Initial Release The measurements shown in this report were made in accordance with the procedures specified in §2.947. I assume full responsibility for the accuracy and completeness of these measurements, and for the qualifications of all persons taking them. HCT CO., LTD. Certifies that no party to this application has subject to a denial of Federal benefits that includes FCC benefits pursuant to section 5301 of the Anti-Drug Abuse Act of 1998,21 U.S. C.853(a) * The report shall not be reproduced except in full(only partly) without approval of the laboratory. F-TP22-03 (Rev. 03) Page 4 of 250 Report No. HCT-RF-2105-FC002 CONTENTS 1. GENERAL INFORMATION5 2. EUT DESCRIPTION6 3. TEST METHODOLOGY7 3.1 EUT CONFIGURATION 7 3.2 EUT EXERCISE 7 3.3 GENERAL TEST PROCEDURES 7 3.4 DESCRIPTION OF TEST MODES 8 4. INSTRUMENT CALIBRATION8 5. FACILITIES AND ACCREDITATIONS8 5.1 FACILITIES 8 5.2 EQUIPMENT 8 6. WORST CASE CONFIGURATION AND MODE9 7. SUMMARY TEST OF RESULTS10 8. TEST RESULT14 8.1 Carrier Output Power 14 8.2 Carrier Frequency Stability 17 8.3 Occupied Bandwidth 34 8.4 Modulation Limiting 64 8.5 Audio Frequency Response / Audio Low Pass Filter Response 89 8.6 Emission Mask 127 8.7 Transient Frequency Behavior 157 8.8 Unwanted Emissions : Conducted Spurious Emission 183 8.9 Adjacent Channel Power 234 8.10 Unwanted Emissions : Radiated Spurious Emission 242 8.11 Necessary Bandwidth Calculations 248 9. LIST OF TEST EQUIPMENT249 10. ANNEX A_ TEST SETUP PHOTO250 F-TP22-03 (Rev. 03) Page 5 of 250 Report No. HCT-RF-2105-FC002 1. GENERAL INFORMATION Manufacturer: JVCKENWOOD Corporation Address: 1-16-2 Hakusan Midori-ku Yokohama-shi Kanagawa 226-8525 Japan FCC ID: K44501103 EUT Type: UHF TRANSCEIVER Model(s): NX-1300-K3 Additional Model(s): N X-1300-K, NX-1300-K2, NX-1302-K Date(s) of Tests: April 16, 2021 ~ May 12, 2021 Place of Tests: HCT Co., Ltd. 74, Seoicheon-ro 578beon-gil, Majang-myeon, Icheon-si, Gyeonggi-do, 17383, Rep. of KOREA F-TP22-03 (Rev. 03) Page 6 of 250 Report No. HCT-RF-2105-FC002 2. EUT DESCRIPTION Power Supply Voltage DC 7.5V Output Power 5 W (Power output continuously variable to 1 W) (Max : 5.2 W) Output Power (16K0F3E) 470-512 MHz : 5 W (Power output continuously variable to 1 W) 450-512 MHz : 2 W (Power output continuously variable to 1 W) Battery type KNB-45L Li-Ion Battery Pack (2000mA) KNB-53N Ni-MH Battery Pack (1400mA) KNB-29N Ni-MH Battery Pack (1500mA) KNB-69L Li-ion Battery Pack (2450mA) KNB-82LC (Li-ion Battery Pack) KNB-84L Li-Ion Battery Pack (2000mA) Antenna KRA-23M UHF Low Profile Helical Antenna (440-490 MHz) KRA-23M2 UHF Low Profile Helical Antenna (470-520 MHz) KRA-27M UHF Whip Antenna (440-490 MHz) KRA-27M2 UHF Whip Antenna (470-520 MHz) KRA-42M UHF Stubby Antenna (440-490 MHz) KRA-42M2 UHF Stubby Antenna (470-520 MHz) Peak Antenna gain KRA-23M UHF Low Profile Helical Antenna: 0 dBd KRA-23M2 UHF Low Profile Helical Antenna: 0 dBd KRA-27M UHF Whip Antenna: 0 dBd KRA-27M2 UHF Whip Antenna: 0 dBd KRA-42M UHF Stubby Antenna: 0 dBd KRA-42M2 UHF Stubby Antenna: 0 dBd Type of Emission 16K0F3E, 11K0F3E: Analogue 8K30F1E, 8K30F1D, 8K30F7W: NXDN 7K60FXD, 7K60FXE: DMR 4K00F1E, 4K00F1D, 4K00F7W: NXDN 4K00F2D: CWID Channel Bandwidth 25 kHz / 6.25 kHz / 12.5 kHz Operating Temperature -30 ˫ ~ +60 ˫ Frequency Range 450 MHz ~ 512 MHz Test Frequency 450.05 MHz / 481.05 MHz / 511.95 MHz Test Frequency (16K0F3E) 2W : 450.05 MHz / 481.05 MHz / 511.95 MHz 5W : 470.05 MHz / 491.05 MHz / 511.95 MHz Maximum deviation 16K0F3E: ± 5 kHz 11K0F3E: ± 2.5 kHz Frequency Stability ± 1.0 ppm F-TP22-03 (Rev. 03) Page 7 of 250 Report No. HCT-RF-2105-FC002 3. TEST METHODOLOGY TIA-603-E dated March 2016 entitled ˑLand Mobile FM or PM Communications Equipment Measurement and Performance Standards˒ were used in the measurement. 3.1 EUT CONFIGURATION The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner that intends to maximize its emission characteristics in a continuous normal application. 3.2 EUT EXERCISE The EUT was operated in the engineering mode to fix the Tx frequency that was for the purpose of the measurements. According to its specifications, the EUT must comply with the requirements of the FCC Rules Part 2 and Part 22, 74, 90. 3.3 GENERAL TEST PROCEDURES Radiated Emissions Radiated emission measurements are performed in the Fully-anechoic chamber. The equipment under test is placed on a non-conductive table 3-meters away from the receive antenna in accordance with ANSI/TIA-603-E-2016. The turntable is rotated through 360 degrees, and the receiving antenna scans in order to determine the level of the maximized emission. The level and position of the ma…

Text truncated - open the document above for the full version.

F-TP22-03 (Rev. 03) Page 171 of 250 Report No. HCT-RF-2105-FC002 11K0F3E (450.05 MHz)_High F-TP22-03 (Rev. 03) Page 172 of 250 Report No. HCT-RF-2105-FC002 (481.05 MHz)_High F-TP22-03 (Rev. 03) Page 173 of 250 Report No. HCT-RF-2105-FC002 (511.95 MHz)_High F-TP22-03 (Rev. 03) Page 174 of 250 Report No. HCT-RF-2105-FC002 (450.05 MHz)_Low F-TP22-03 (Rev. 03) Page 175 of 250 Report No. HCT-RF-2105-FC002 (481.05 MHz)_ Low F-TP22-03 (Rev. 03) Page 176 of 250 Report No. HCT-RF-2105-FC002 (511.95 MHz)_ Low F-TP22-03 (Rev. 03) Page 177 of 250 Report No. HCT-RF-2105-FC002 4K00F1E (450.05 MHz)_High F-TP22-03 (Rev. 03) Page 178 of 250 Report No. HCT-RF-2105-FC002 (481.05 MHz)_High F-TP22-03 (Rev. 03) Page 179 of 250 Report No. HCT-RF-2105-FC002 (511.95 MHz)_High F-TP22-03 (Rev. 03) Page 180 of 250 Report No. HCT-RF-2105-FC002 (450.05 MHz)_Low F-TP22-03 (Rev. 03) Page 181 of 250 Report No. HCT-RF-2105-FC002 (481.05 MHz)_ Low F-TP22-03 (Rev. 03) Page 182 of 250 Report No. HCT-RF-2105-FC002 (511.95 MHz)_ Low F-TP22-03 (Rev. 03) Page 183 of 250 Report No. HCT-RF-2105-FC002 8.8 Unwanted Emissions : Conducted Spurious Emission Ӑ Definition Conducted spurious emissions are emissions at the antenna terminals on a frequency or frequencies that are outside a band sufficient to ensure transmission of information of required quality for the class of communication desired. Ӑ TEST CONFIGURATION Ӑ TEST PROCEDURE According to 2.2.13 in TIA-603-E Standard. e) Connect the equipment as illustrated, with the notch filter by-passed. f) Set the center frequency of the spectrum analyzer to the assigned transmitter frequency, key the transmitter, and set the level of the carrier to the full scale reference line. g) Modulate the transmitter with a 2500 Hz sine wave at an input level 16 dB greater than that necessary to produce 50% of rated system deviation. The input level shall be established at the frequency of maximum response of the audio modulation circuit. h) Adjust the spectrum analyzer for the following settings: 1) Resolution Bandwidth = 10 kHz for spurious emissions below 1 GHz, and 1 MHz for spurious emissions above 1 GHz. 2) Video Bandwidth ͖3 times the resolution bandwidth. 3) Sweep Speed ͕2000 Hz per second. 4) Detector Mode = mean or average power. e) Adjust the center frequency of the spectrum analyzer for incremental coverage of the range from: 1) The lowest radio frequency generated in the equipment to the carrier frequency minus the test bandwidth (see 1.3.4.4). F-TP22-03 (Rev. 03) Page 184 of 250 Report No. HCT-RF-2105-FC002 2) The carrier frequency plus the test bandwidth to a frequency less than 2 times the carrier frequency. f) Record the frequencies and levels of spurious emissions from step e). g) Unkey the transmitter. Replace the transmitter under test with the signal generator and adjust the signal level to reproduce the frequencies and levels of every spurious emission recorded in step f). Record the signal generator levels in dBm. h) Insert the notch filter. i) Adjust the spectrum analyzer for the following settings: 1) Resolution Bandwidth = 10 kHz for spurious emissions below 1 GHz, and 1 MHz for spurious emissions above 1 GHz. 2) Video Bandwidth ͖3 times the resolution bandwidth. 3) Sweep Speed ͕2000 Hz per second. 4) Detector Mode = mean or average power. j) Key the transmitter. Adjust the center frequency of the spectrum analyzer for incremental coverage of the range from a frequency equal to 2 times the carrier frequency and to the tenth harmonic of the carrier frequency. F-TP22-03 (Rev. 03) Page 185 of 250 Report No. HCT-RF-2105-FC002 Ӑ TEST RESULTS Type of Emission Power Test Frequency (MHz) Measured Frequency (MHz) Result (dBm) Limit (dBm) Margin (dB) 16K0F3E High Power (2W) 450.05 0.130 -50.10 -13.000 37.101 0.260 -53.83 -13.000 40.828 900.080 -39.14 -13.000 26.138 4907.545 -29.97 -13.000 16.970 481.05 0.129 -49.55 -13.000 36.550 0.260 -52.…

Text truncated - open the document above for the full version.