KLS-NAV5PLUS-1NAV5plus

ICS NAV5plus GMDSS NAVTEX Receiver User Guide VESSEL IDENTIFICATION INFORMATION Name Call Sign MMSI ICS NAV5plus S/N RX frequencies518 kHz 490 kHz The technical data, information and illustrations contained in this publication were to the best of our knowledge correct at the time of going to print. We reserve the right to change specifications, equipment, installation and maintenance instructions without notice as part of our policy of continuous product development and improvement. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, electronic or otherwise without permission in writing from McMurdo Limited. No liability can be accepted for any inaccuracies or omissions in the publication, although every care has been taken to make it as complete and accurate as possible. Safety Warnings This instrument is for use as an aid to sailors and should not lead to a reduction in the level of good seamanship required at all times. Reception of messages cannot always be guaranteed as this depends on local radio propagation. Contents Quick Start .................................................................................................... 1 Introduction ................................................................................................... 1 How To Operate Your ICS NAV5plus........................................................... 3 System Alarms.............................................................................................. 8 Serial Output ................................................................................................. 9 Tearing off a Printout .................................................................................. 11 Paper Loading............................................................................................. 11 Installation................................................................................................... 14 Self Test...................................................................................................... 24 Troubleshooting Guide ............................................................................... 26 Warranty ..................................................................................................... 29 Options........................................................................................................ 30 Specifications.............................................................................................. 31 Appendix II: Message Type Indicators ....................................................... 36 Appendix III: Declaration of Conformity ...................................................... 37 Please take the time to read this manual carefully. It contains some essential information regarding the operation and maintenance of the product and a useful background to the NAVTEX system. We recommend that you regularly visit the McMurdo website www.mcmurdo.co.uk for information on updates, the availability of software enhancements, further options and support. The support pages contain frequently asked questions about the ICS NAV5plus that you may find useful. There is also a NAVTEX database providing a list of operational NAVTEX stations and their details. The IMO and various national coastguards also operate informative websites that you may wish to visit, see the links page at www.mcmurdo.co.uk. 1 QUICK START You will find this product extremely easy to operate. • Follow the installation guidelines • Re-check the cable connections • Apply power • Switch on the ICS NAV5plus • The ICS NAV5plus will now print NAVTEX messages INTRODUCTION NAVTEX is a method of transmitting navigational warnings and weather forecasts from designated coast radio stations. All English language transmissions are made on 518 kHz. Each station is allocated several time ‘slots’ during the day, when it is permitted to transmit; these are normally at four hourly intervals. The only exceptions to this are gale warnings and search and rescue messages, which may be transmitted at any time. Reception of NAVTEX is normally limited to an area of 200 - 300 miles radius around each transmitting station, although considerably greater ranges are possible at night. Subject to IMO approval, additional local language transmissions may be made on 490 kHz. The ICS NAV5plus has been designed to the latest European and International specifications to provide up to date weather and navigation warning information to commercial vessels. It meets IMO requirements under GMDSS and is designed for simplicity of operation. It will provide reliable printed information day after day within designated NAVTEX coverage areas. 2 Installation is straightforward. Connect the ICS NAV5plus to a 12 or 24 volt DC supply and connect a suitable antenna. Switch it on, and it will start printing NAVTEX messages without further manual intervention. Note that if there are only a couple of NAVTEX stations within range it may be several hours before you receive the first message If all stations and message types are left selected, the ICS NAV5plus may overwhelm you with information. It can therefore be set up to print only those stations and message categories you want to receive and which are applicable to the area in which you are sailing. Normally, routine messages are repeated at four hourly intervals. Provided that the ICS NAV5plus is left running, repeated messages are not printed again. The suppression of repeated messages stops three days (72 hours) after the last transmission of the message. Permanent installation of the ICS NAV5plus can be made with the bulkhead-mounting bracket provided. Alternatively, the optional FMT-2 flush panel mounting kit, part number 913-24, may be purchased. A NAVTEX antenna should be mounted where it is elevated clear of metal objects in a location where it cannot easily be damaged. Please read the installation section of the user guide tho…

Text truncated - open the document above for the full version.

1 of 1 TITLE NAV5 ANTENNA CONNECTOR PCB ASSY APPROVED ISSUE DATE CHG.No. DOC REF PLT02129.XLS 4 19/11/2002 1333 McMurdo Limited DWG REF 5 06/07/2003 1348 Silver Point Airport Service Road DATE 22/04/2002 6 11/02/2004 C2642 Portsmouth PO3 5PB THIS DOCUMENT IS UNCONTROLLED, UNLESS OTHERWISE STATED ITEM QTY REFERENCE MFRs PART No MFR DESCRIPTION PITCH PACKAGE COMMENTS 1 1 C100 DE1005F103Z1K MURATA CAPACITOR, DISK CERAMIC, 10n, 1kV FAR 219-496 2 1 J104 9-215079-0 AMP CONNECTOR, MICROMATCH 20WAY 0.05" OR EQUIVALENT 3 1 J102 251-8301 RS CONNECTOR, HEADER, 10WAY 0.1" USE 10/36ths OF STRIP 4 1 J105 SL5.08/6/180B KLIPPON CONNECTOR, PCB HEADER, 6WAY 5.08mm OR EQUIVALENT 5 2 J100,101 22-05-7028 MOLEX CONNECTOR,SQUARE PIN HEADER, 90º,2WAY 0.1" OR EQUIVALENT 7 1 190-529 RS MACHINE SCREW, M4 x 20mm, A4 S/S, PANHEAD OR EQUIVALENT 8 4 189-636 RS WASHER, M4, A4 S/S OR EQUIVALENT 9 1 187-0487 RS WASHER, SHAKEPROOF, M4, A4 S/S OR EQUIVALENT 10 3 527-252 RS NUT, M4, A4 S/S OR EQUIVALENT 11 1 PCB02123.PCB PCB, NAV-5 ANTENNA CONNECTOR, ISSUE 1 McMurdo Limited Connector PCB Assy PLT02129 Iss.6 printed 12/08/2004

1 of 1 TITLE NAV5PLUS FINAL ASSEMBL Y APPROVED ISSUE DATE CHG.No. DOC REF PLT00612-01 CJM 1 02/10/2003 C2602 McMurdo Limited DWG REF 28-224A CJM 2 22/07/2004 C2881 Silver Point Airport Service Road DATE 10/02/2003 Portsmouth PO3 5PB THIS DOCUMENT IS UNCONTROLLED, UNLESS OTHERWISE STATED ITEM QTY REFERENCE MFRs PART No MFR DESCRIPTION PITCH PACKAGE COMMENTS 1 1 28-217D McM NAV5plus Case Body, Finished Calls DWG00630 & 28-217N 2 1 28-219D McM NAV5plus Internal Section Calls DWG00608 3 1 28-216D McM NAV4/5 Case Door, Finished Calls DWG00243 & 28-216N 4 2 28-215D McM NAV4/5 Endplate, Plastic colour Pantone 431U 5 1 DWG00274 ICS NAV-5 Hinge Pin 6 1 31-245D McM NAV4/5 Paper Roll Bracket Chgd @ Iss. 2 - was ICS DWG00552 7 1 31-243D McM NAV4/5 Paper Roll Bar Chgd @ Iss. 2 - was ICS DWG00553 89 1 28-214D McM NAV5plus Membrane Keypad Calls 28-214N (Artwork) 10 1 DWG00557 PLT00558 ICS NAV4/5 Main PCB Assembly 11 1 DWG00318 PLT00319 ICS NAV5 LCD Assembly 12 1 PLT02121 ICS NAV5 Dual Receiver PCB Assembly 13 1 DWG00623 PLT00624 ICS NAV5 Keypad Extension Cable Assembly 14 1 DWG00593 31-250D McM NAV4/5 Printer Assembly Chgd @ Iss. 2 - was ICS PLT00594 15 1 DWG00597 31-244D McM NAV4/5 Paper Out Sensor Assembly Chgd @ Iss. 2 - was ICS PLT00598 16 2 DWG02122 PLT02126 ICS NAV5 Antenna Connector Cable 17 1 FP38-6.35-10 Kitagawa Ferrite Clamp New at Issue 2 18 1 367 01 1705 ITW Fastex Door Latch 19 2 Screw, M2.5 x 15mm Csk 20 10 Screw, No.4 x 1/2" SS Csk Self-tap 21 4 Screw, M3 x 5mm Phead Taptite 2223 2 Screw, M3 x 20mm Csk Pozi 24 2 Washer, M3 Plain 25 2 Nut, M3 Full 26 2 Nut, M2.5 Full 27 2 Washer, M3 Serrated 28 2 048 4817 Heyco Spacer, 6.35 OD x 2.92 ID x 7.94 L, Nylon 29 1 DWG02139 PLT02129 ICS NAV5 Antenna Connector PCB Assembly 30 1 28-221E McM NAV5 Plus Chassis Label Set Calls 28-221 (Artwork) Chgd at Iss. 2 31 1 DWG02614 PLT02175 NAV5 Receiver to Main pcb Interconnect 32 1 90-7017D McM Ships Wheel Label New at Issue 2 McMurdo Limited Final Assy PLT00612-01 Iss.2 printed 12/08/2004

1 of 3 TITLE NAV4/5 MAIN PCB ASSEMBL Y ISSUE DATE APP'D CH No. DOC REF PLT00558 8 09/10/2002 1329 McMurdo Limited DWG REF DWG00557 9 27/07/2004 CJM C2946 Silver Point Airport Service Road Portsmouth PO3 5PB THIS DOCUMENT IS UNCONTROLLED UNLESS OTHERWISE STATED ITEM QTY REFERENCE MFRs PART No MFR DESCRIPTION PITCH PACKAGE COMMENTS 1 2 U1,2 74HC245 VARIOUS IC, OCTAL BI-DIR. BUFFER DIP20 2 1 U3 74AC32 VARIOUS IC, QUAD OR DIP14 3 1 U4 74AC04 VARIOUS IC, HEX INVERTER DIP14 4 1 U5 uPD27C512 NEC IC, CMOS EPROM 64k X 8, 200ns or faster CERAMIC DIP Program s/w 915XX Version 2.10 51U6 uPD43256C-xxL NEC IC, CMOS SRAM 32k X 8,LOW PWR, 150ns or faster L OR LL VERSIONS ONLY 6 1 U7 74AC139 VARIOUS IC, DUAL 1 OF 4 DECODER DIP16 7 1 U8 uPD70320L-8 NEC IC, 16 BIT MICROCONTROLLER PLCC84 8 1 U9 74HC132 NAT SEMI IC, QUAD SCHMITT NAND DIP14 ALT MFR'S MAY CHANGE BEEPER 9 1 U10 ULN2003A VARIOUS IC, DARLINGTON ARRAY PLASTIC DIL 10 1 U11 MAX690CPA MAXIM IC, uP SUPERVISORY CIRCUIT DIP8 11 1 U13 4013B VARIOUS IC, DUAL 'D' TYPE FLIP FLOP DIP14 12 1 U14 LM2576HVT-5.0 NAT SEMI IC, SWITCHMODE VOLTAGE REGULATOR, HI-VOLTAGE TO220-5 13 1 U15 SN75179 NAT SEMI IC, DIFFERENTIAL DRIVER & RECEIVER PAIR DIP8 1415 1 Q1 BS170 VARIOUS MOSFET, N-CHANNEL SWITCH TO92 16 4 Q2,3,4,7 BC327 VARIOUS TRANSISTOR, PNP TO92 17 1 Q5 BD680 VARIOUS TRANSISTOR, PNP POWER DARLINGTON TO126 18 1 Q6 BC547B VARIOUS TRANSISTOR, NPN TO92 1920 3 D1,2,8 1N4148 VARIOUS DIODE, HIGH SPEED SILICON 0.3" DO-35 21 2 D4,6 BYV28-200 VARIOUS DIODE, ULTRAFAST RECTIFIER 3.5A SOD-64 22 1 D5 1.5KE39A GS DIODE, TRANSIENT SUPPRESSOR, 1500W 23 1 D7 BZX79-C4V7 PHILIPS DIODE, ZENER 4V7 400mW 0.3" D0-35 2425 1 XTAL1 VARIOUS CRYSTAL, 14.74560MHz, PL RES, Cl=30pF HC18/U HIGH STABILITY 30PPM 26 1 BP1 KBS-15DB-4A KYOCERA PIEZO CERAMIC BEEPER, FLYING LEADS 27 1 RL1 G2E-184PH-M IMO RELAY, SPCO, 1A 24VDC, 5V COIL, SEALED DIP FORMAT PED 18731131561,TAIKO NXE-6K 2829 1 R1 MRS16T PHILIPS RES, 3k9 1% 0.3" 30 3 R2,6,25 MRS16T PHILIPS RES, 180R 1% 50PPM 0.3" 31 1 R3 MRS16T PHILIPS RES, 100R 1% 50PPM 0.3" 32 1 R4 MRS16T PHILIPS RES, 10R 1% 50PPM 0.3" Main PCB Assy PLT00558 Iss.9 printed 12/08/2004 2 of 3 TITLE NAV4/5 MAIN PCB ASSEMBL Y ISSUE DATE APP'D CH No. DOC REF PLT00558 8 09/10/2002 1329 McMurdo Limited DWG REF DWG00557 9 27/07/2004 CJM C2946 Silver Point Airport Service Road Portsmouth PO3 5PB THIS DOCUMENT IS UNCONTROLLED UNLESS OTHERWISE STATED ITEM QTY REFERENCE MFRs PART No MFR DESCRIPTION PITCH PACKAGE COMMENTS 33 4 R5,16,22,30 MRS16T PHILIPS RES, 2k2 1% 50PPM 0.3" 34 4 R7,8,17,33 MRS16T PHILIPS RES, 4k7 1% 50PPM 0.3" 35 3 R9,26,29 MRS16T PHILIPS RES, 47k 1% 50PPM 0.3" 36 1 R12 MRS16T PHILIPS RES, 5k1 1% 50PPM 0.4" 37 1 R13 MRS16T PHILIPS RES, 15k 1% 50PPM 0.3" 38 1 R19 MRS16T PHILIPS RES, 22k 1% 50PPM 0.3" 39 1 R20 MRS16T PHILIPS RES, 470k 1% 0.3" 40 1 R21 MRS16T PHILIPS RES, 100k 1% 50PPM 0.3" 41 1 R31 MRS16T PHILIPS RES, 33k 1% 50PPM 0.3" 42 7 R41,42,43,44,45,46,47 4609X-101-10k BOURNS RES ARRAY, 10k x 8, SIL 44 1 R48 4608X-102-100R BOURNS RES ARRAY, 100R x 4 INDIVIDUAL, SIL 45 1 R49 4608X-102-100k BOURNS RES ARRAY, 100k x 4 INDIVIDUAL, SIL 46 1 R27 MRS25 PHILIPS RES, 2k2 1% 100PPM 0.3" 47 2 R23,28 4608X-102-220R BOURNS RES ARRAY, 220R x 4 INDIVIDUAL, SIL 48 2 R15,18 4610X-102-220R BOURNS RES ARRAY, 220R x 5 INDIVIDUAL, SIL 49 1 R40 4609X-102-2K2 BOURNS RES ARRAY, 2k2 x 8, SIL 50 2 RV1,2 B72205S0110K101 EPCOS VARISTOR, S05K11 0.2" 51 1 C2 FKC2 WIMA CAP, POLYCARBONATE, 470p 100V 5mm 52 9 C4,5,7,10,15,16,20,21,23 CW15A 472M PHILIPS CAP, CER.MULTILAYER, 4n7 100V 0.1" 53 5 C6,17,18,25,29 CW20C104M-244 PHILIPS CAP, CER.MULTILAYER, 100n 63V 0.1" 54 4 C1,3,14,19 CW15A102M PHILIPS CAP, CER MULTILAYER, 1n 100V 0.1" 55 1 C9 489D475X0010A6 SPRAGUE CAP, TANTALUM, 4u7 10V 0.2" 56 1 C11 682 34569 PHILIPS CAP, CERAMIC LOW K, 56pF 100V 0.1" 57 1 C12 682 10229 PHILIPS CAP, CERAMIC LOW K, 22pF 100V 0.1" 58 1 C13 FKS2 WIMA CAP, MET.POLYESTER, 3n3 100V 10% 0.2" 59 2 C8,24 DSG DUBILIER CAP, ELECT., 470uF 63V, LO ESR 5mm MAX DIA = 12.5mm, HEIGHT = 20mm 60 1 C26 DSG DUBILIER CAP, ELECT., 1000uF 10V, LO ESR 5mm MAX DIAMETER = 10mm 61 1 C27 DSG DUBILIER CAP, ELECT., 470uF 10V, LO ESR 3.5mm MAX DIAMETER = 8mm 62 1 C28 TZ03R300ER169 MURATA CAP, VARIABLE, 5p2 - 30p 100V 5mm 63 1 BR1 LM2430-3PH SAFT BATTERY, 200mAh LITHIUM PCB MTG VERT. MTG. CAN USE CR2032 TYPES 6465 1 L1 RN112-0.8/02 SCHAFFNER COMMON MODE CHOKE Main PCB Assy PLT00558 Iss.9 printed 12/08/2004 3 of 3 TITLE NAV4/5 MAIN PCB ASSEMBL Y ISSUE DATE APP'D CH No. DOC REF PLT00558 8 09/10/2002 1329 McMurdo Limited DWG REF DWG00557 9 27/07/2004 CJM C2946 Silver Point Airport Service Road Portsmouth PO3 5PB THIS DOCUMENT IS UNCONTROLLED UNLESS OTHERWISE STATED ITEM QTY REFERENCE MFRs PART No MFR DESCRIPTION PITCH PACKAGE COMMENTS 66 1 L2 14 224 35 NEWPORT INDUCTOR, 220uH 3.5A, BOBBIN TYPE 67 1 L3 B78108-S1103-K SIEMENS INDUCTOR, 10uH 0.68A 0.6" AXIAL 68 1 L4 181LY-473J TOKO INDUCTOR, 10RB SERIES, 47mH 69 2 L5,6 BL01RN1-A1D2B MuRATA INDUCTOR, EMI SUPPRESSION 70 1 J1 SL10-CL-V KLIPPON CONNECTOR, PCB HEADER 10 WAY 0.2" 71 1 J4 FLS14-5-T FLAIR CONNECTOR, 5 WAY ST PIN LOCKING HEADER 0.1" 72 1 J5 T51-1000-1080 FLAIR CONNECTOR, 8 WAY 0.1" 73 1 J7 FLS14-4-T FLAIR CONNECTOR, 4 WAY ST PIN LOCKING HEADER 0.1" 74 2 J8,12 9-215079-0 AMP CONNECTOR, 20 WAY ST PIN HEADER 0.05" 75 1 J9 9-215079-2 AMP CONNECTOR, 12 WAY RA PIN HEADER 0.05" 76 1 J13 FLS14-10-T FLAIR CONNECTOR, 10 WAY ST PIN LOCKING HEADER 0.1" 7778 1 LK1 VARIOUS CONNECTOR, DUAL ROW 3 WAY PIN HEADER 0.1" 79 2 LK1 VARIOUS CONNECTOR, JUMPER LINKS 8081 1 U5 D01-9973221 HARWIN CON, 32 PIN IC STRIP SOCKET, SIL 0.1" BREAK INTO 2 x 14 WAY 82 1 U8 D72184C-06 HARWIN CON, 84 PIN PLCC SOCKET 83 1 U1 D01-9973221 HARWIN CON, 32 PIN IC STRIP SOCKET, SIL 0.1" BREAK INTO 2 x 10 WAY 8485 1 0580.PCB ICS PCB, 127 X 90.5 4 LAYER PTH ISSUE 3 868788899091929394959697 Main PCB Assy PLT00558 Iss.9 printed 12/08/2004

1 of 6 TITLE NAV-5 DUAL (518/490) RECEIVER PCB ASSY APPROVED ISSUE DATE MOD DOC REF PLT02121.XLS CJM 6 03/03/2003 1356 DWG REF CJM 7 22/07/2004 C2881 DATE 11/04/2002 THIS DOCUMENT IS UNCONTROLLED, UNLESS OTHERWISE STATED ITEM QTY REFERENCE MFRs PART No MFR PITCH PACKAGE 1 6 C104,110,111,112,113,116 0603 2 37 C103,106,200,202,203,206, 0805 C209,213,215,216,224,225, C226,234,235,236,238,249, C252,302,303,306,309,313, C315,316,324,325,326,334, C335,336,338,349,352,501,C513 3 1 C102 1206 4 15 C100,127,212,223,237,239, EEVFC1H1R0R PANASONIC SM_ELEC_4 C250,251,253,312,323,337, C339,350,351 5 3 C101,107,114 EEVFC1H100P PANASONIC SM_ELEC_6.3 6 2 C205,305 0603 7 2 C204,304 0603 8 2 C208,308 TZBX4 series MURATA 9 28 C201,210,211,214,217,218, 1206 C221,227,230,232,233,242,C243,245,301,310,311,314,C317,318,327,332,333,321,C330,342,343,345 10 8 C220,229,241,244,320,329, 1206 C341,344 11 4 C219,228,319,328 1206 12 10 C109,117,118,119,222,231, EEVFC1C470R PANASONIC SM_ELEC_6.3 C240,322,331,340 13 2 C108,115 ECA1HM471 PANASONIC 5mm 14 6 C502,503,504,506,509,512 0805 15 2 C507,508 1206 16 2 C510,511 1206 57 1 C002 1206 58 1 C307 0603 61 2 C254,300 0603 CAPACITOR, MULTI CER, 10n, X7R, 50VCAPACITOR, MULTI CER, 100n, X7R, 25V CAPACITOR, MULTI CER, 100n, X7R, 50VCAPACITOR, AL SMD, 1u, 50V, CASE BCAPACITOR, AL SMD, 10u, 50V, CASE DCAPACITOR, MULTI CER, 330p, X7R, 16VCAPACITOR, MULTI CER, 220p, X7R, 16V8p5-40p TRIM CAPCAPACITOR, CERAMIC NP0, 10n, 25V, 5%CAPACITOR, CERAMIC NP0, 2n7, 25V, 5%CAPACITOR, CERAMIC NP0, 8n2, 25V, 5%CAPACITOR, AL SMD, 47u, 16V CASE DCAPACITOR, ELECT., 470uF 50VCAPACITOR, MULTI CER, 18p, COG, 25VCAPACITOR, MULTI CER, 150p, COG, 25VCAPACITOR, MULTI CER, 1800p, COG, 25VCAPACITOR, MULTI CER, 4700p, COG, 25VCAPACITOR, MULTI CER, 1uF, Z5U, 25VDESCRIPTIONCAPACITOR, MULTI CER, 1n, X7R 50V McMurdo Limited PLT02121 printed 12/08/2004 2 of 6 TITLE NAV-5 DUAL (518/490) RECEIVER PCB ASSY APPROVED ISSUE DATE MOD DOC REF PLT02121.XLS CJM 6 03/03/2003 1356 DWG REF CJM 7 22/07/2004 C2881 DATE 11/04/2002 THIS DOCUMENT IS UNCONTROLLED, UNLESS OTHERWISE STATED ITEM QTY REFERENCE MFRs PART No MFR PITCH PACKAGE DESCRIPTION 17 1 D101 GF1A GEN SEMI DO-214BA 18 4 D200,201,300,301 BAV99 SOT-23 19 4 D500,501,502,503 BAS16 SOT-23 20 1 L100 RN102-0.3/0.2 SCHAFFNER 21 1 L500 NL252018T100J TDK 1210 22 2 L503,506 RZCS-45330R TOKO 23 4 L501,502,504,505 RZCS-45329R TOKO 24 2 Q200,300 BC847B SOT-23 25 4 R200,201,300,301 0603 26 4 R109,110,111,114 0603 27 2 R204,304 0603 28 8 R104,105,106,107,228,229, 0603 R328,329 29 4 R205,206,305,306 0603 30 8 R203,207,211,220,303,307, 0603 R311,320 31 8 R208,214,221,222,308,314, 0603 R321,322 32 4 R210,213,310,313 0805 33 20 R215,216,217,223,224,225, 0603 R234,235,236,237,315,316,R317,323,324,325,334,335,R336,337 34 3 R212,312,500 0805 35 7 R202,209,232,240,302,309, 0805 R332 36 2 R241,341 0805 37 4 R218,244,318,344 0805 38 4 R242,243,342,343 0603 39 4 R219,227,319,327 0603 DIODE, GF1ADIODE, BAV99DIODE, BAS16COMMON MODE CHOKEINDUCTOR, 10uHTRANSFORMER, PRI 15, SEC1 82, SEC 2 60TRANSFORMER, PRI 6, SEC1 82, SEC 2 60TRANSISTOR, NPNRESISTOR, 3k3RESISTOR, 47kRESISTOR, 1kRESISTOR, 10kRESISTOR, 47kRESISTOR, 2k4RESISTOR, 120KRESISTOR, 22kRESISTOR, 130kRESISTOR, 10RRESISTOR, 100R RESISTOR, 1KRESISTOR, 10KRESISTOR, 1MegRESISTOR, 1Meg2 McMurdo Limited PLT02121 printed 12/08/2004 3 of 6 TITLE NAV-5 DUAL (518/490) RECEIVER PCB ASSY APPROVED ISSUE DATE MOD DOC REF PLT02121.XLS CJM 6 03/03/2003 1356 DWG REF CJM 7 22/07/2004 C2881 DATE 11/04/2002 THIS DOCUMENT IS UNCONTROLLED, UNLESS OTHERWISE STATED ITEM QTY REFERENCE MFRs PART No MFR PITCH PACKAGE DESCRIPTION 40 4 R226,230,326,330 0603 41 4 R231,233,331,333 0603 42 1 R100 0603 43 2 R103,108 0603 59 1 R001 1206 60 1 R102 0805 44 1 J1 FLS14-10-T FLAIR 0.1" 45 2 J4,5 FLS14-2-T FLAIR 0.1" 46 4 U204,205,304,305 74HC74D PHILIPS SO-14 47 1 U100 LM317HVT NAT SEMI T0-220 48 1 U101 LM317T NAT SEMI T0-220 49 1 U102 LM339AM NAT SEMI SO-14 50 4 U203,206,303,306 TL074 TI SO-14 51 2 U200,300 MAX4252 MAXIM SO-8 52 4 U201,202,301,302 SA602AD PHILIPS SO-8 53 1 U307 TLO72 TI SO-8 54 1 Y200 HC49 55 1 Y300 HC49 56 1 2121.PCB RESISTOR, 1Meg8RESISTOR, 6Meg8RESISTOR, 2kRESISTOR, 330RRESISTOR, 2M2RESISTOR, 0R0CONNECTOR, 10 WAY ST PIN LOCKING HEADERCONNECTOR, 2 WAY ST PIN LOCKING HEADERIC, DOUBLE BALANCED MIXER SA602AIC, DUAL D-TYPE FLIP-FLOP, 74HC74IC,ADJUSTABLE REGULATOR, LM317IC,ADJUSTABLE REGULATOR, LM317PCB, NAV-5 DUAL RECEIVER, ISSUE 4IC, OP-AMP, DUAL, TL0724.144MHz, HC49, 20ppm tol, 10ppm/C tempCo, 30pF, -25 to +85 degC 3.920MHz, HC49, 20ppm tol, 10ppm/C tempCo, 30pF, -25 to +85 degC IC, QUAD COMPARATOR, LM339AMIC, OP-AMP, QUAD, TL074IC, OP-AMP MAX4252 McMurdo Limited PLT02121 printed 12/08/2004 4 of 6 TITLE NAV-5 DUAL (518/490) RECEIVER PCB ASSY APPROVED ISSUE DATE MOD DOC REF PLT02121.XLS CJM 6 03/03/2003 1356 McMurdo Limited DWG REF CJM 7 22/07/2004 C2881 Silver Point Airport Service Road DATE 11/04/2002 Portsmouth PO3 5PB THIS DOCUMENT IS UNCONTROLLED, UNLESS OTHERWISE STATED ITEM QTY REFERENCE MFRs PART No MFR PITCH PACKAGE COMMENTS 1 6 C104,110,111,112,113,116 0603 Chgd @ Iss. 7 2 37 C103,106,200,202,203,206, 0805 C209,213,215,216,224,225, C226,234,235,236,238,249, C252,302,303,306,309,313, C315,316,324,325,326,334, C335,336,338,349,352,501,C513 3 1 C102 1206 4 15 C100,127,212,223,237,239, EEVFC1H1R0R PANASONIC SM_ELEC_4 C250,251,253,312,323,337, C339,350,351 5 3 C101,107,114 EEVFC1H100P PANASONIC SM_ELEC_6.3 6 2 C205,305 0603 7 2 C204,304 0603 8 2 C208,308 TZBX4 series MURATA 9 28 C201,210,211,214,217,218, 1206 C221,227,230,232,233,242,C243,245,301,310,311,314,C317,318,327,332,333,321,C330,342,343,345 10 8 C220,229,241,244,320,329, 1206 C341,344 11 4 C219,228,319,328 1206 12 10 C109,117,118,119,222,231, EEVFC1C470R PANASONIC SM_ELEC_6.3 C240,322,331,340 13 2 C108,115 ECA1HM471 PANASONIC 5mm MAX DIA = 10mm, HEIGHT = 20mm 14 6 C502,503,504,506,509,512 0805 RS 211-3158 15 2 C507,508 1206 FAR 718-592 16 2 C510,511 1206 FAR 718-592 57 1 C002 1206 58 1 C307 0603 61 …

Text truncated - open the document above for the full version.

OPY NUMBER: 2 SSUED TO: Mr. F. L. Robins Managing Director JRS Associates (Wireton Limited) DATE: PORT NO: ROJECT REFERENCE: VISION STATUS: ATE OF ISSUE: SHEET NUMBER: 2437 E7026 01/03/94 1 of 9 SIGNED: r . , , TITLE: CONFIDENTIAL TEST REPORT PRODUCT DESCRIPTION: NA VTEX Receiver Type: NAV- TYPE OF TEST RF. SUSCEPTffiILITY & ELECTROSTATIC DISCHARGE PREPARED FOR: ICS Electronics Limited Unit V , Rudford Industrial Estate Ford , Arundel West Sussex BNI8 OBD United Kingdom ISSUED BY: .... t:.. :..~.................. Director CRANAGE EMC Technology Limited , . r - DA TE: ...... 1/. r/1.Y:.... All communications, documents and apparatus received in the course of this work will be treated by CRANAGE EMC Technology Limited as being COMMERCIAL IN CONFIDENCE. This project report is also regarded as being COMMERCIAL IN CONFIDENCE and is defined as a controlled document within the Quality Assurance System operated by CRANAGE EMC Technology Limited. REPORT NO:2437 PROJECT REF:E7026 REVISION STATUS:OI ISSUE DATE:01/03/94 SHEET 2 OF 9 WORK COMMENCEMENT DATE: 14/02/94 TESTING LABORATORY: CRANAGE EMC Technology Limited Stable Court Oakley Hall Market Drayton Shropshire TF9 4AG TEST ENGINEER: Keith G. Richens B.Sc. (Hons) AMIEE TECHNICAL MANAGER TECHNICAL ASSISTANT: George Stanhope WORK SITE LOCATION: (if different from above) CUSTOMERS OWN REF: O. No. 2686 (refJRS) PRODUCT IDENTIFICATION: NA V- PROJECT OBJECTIVES: Testing to IEC Immunity Test Standards for RF. Susceptibility (conducted and radiated) and Electrostatic Discharge. , ' : I . , . REPORT NO:2437 PROJECT REF:E7026 REVISION STATUS:Ol ISSUE DATE:0l/03/94 SHEET 3 OF 9 TEST EOUIPMENT USED: Item No. QTY Description MFR & Model No. Standard dielectric Cranage EMC Tech. table (heij:!;ht: 800mm) Standard dielectric Cranage EMC Tech. table (heij:!;ht: OOmm) Screened test room Cranage EMC Tech. 5.4m(L) x 2. 9m(W) x 3. 2m(H) (Facility ref P2024) Stripline Test Cell. Cranage EMC Tech. 80l\1Hz to 300l\1Hz (ref stan. IEC801- 1984) Broadband Isotropic Aeritalia TE307 with Electric Field Probe TE308 repeater 10kHz to IGHz Broadband Power EN! 420LA Amplifier, 20W 150kHz to 300MHz Broadband Power Cranage EMC Tech. Amplifier , lW, 10MHz Model 140 to 1 OOOMHz Log Periodic Antenna AH. Systems Inc. 300MHz to 1800MHz Model SAS- 200/51 0 Standard dielectric Cranage EMC Tech. tripod (2m) Signal Generator Hewlett Packard 10kHz to 990MHz 100MHz Oscilloscope Hitachi with XI0 probe Model V- I 050F Mains stop filter Wireton Limited Type M (ref stan. EN55020: 1988) ESD generator MWB Instruments ESD (sn. 10492) ENVIRONMENTAL CONDITIONS OF TEST: The following tests were carried out in the screened test room (3). (Ambient conditions: Temperature =IS , RH = 57% , normal atmospheric pressure). , .: . r . : , ,! . I . ! . r , , I , , i r r I REPORT NO:2437 PROJECT REF:E7026 REVISION STATUS:Ol ISSUE DATE:Ol/03/94 SHEET 4 OF 9 TEST CONFIGURATION: The Equipment Under Test (EUT) comprised aNA V - 5 NA VTEX Receiver connected via 3m length twisted pair cable (30/0. 25mm) to an external 12V power supply. A signal cable was connected via 2m length twisted pair cable (16/0. 2mm) to the remote alarm socket of the EUT. The far ends of the twisted signal pair were soldered to the centre pin of a BNC socket. A computer controlled transmitting device , used to emulate typical data transmissions , was located in the adjacent screened measurement room. The NA VTEX transmitting and receiving antennae were positioned sufficiently close to each other in the screened test room (3) so as to provide an adequate receive signal level to the EUT. Conducted RF Immunity The EUT was operated within the stripline test cell (4), 50rnm above the earth reference plane , and 950rnm above the floor of the screened room (3). The mains stop filter (12) was located on the floor of the screened room (3) at the 12V power point. Radiated RF Immunity 80MHzto 300MHz:- The EUT was operated within the stripline test cell (4). The field probe (5) was positioned 150rnm to the left hand side of the front panel and used to provide continuous feedback of the electric field level at the EUT. RF input , remote alarm and power cables were orientated orthogonal to the E- field vector. 300MHz to 990MHz :- The EUT was re- positioned on the standard dielectric table (1). The radiating antenna (8) was positioned on the centre axis of the EUT at a distance of 1 m in front of the front panel , and orientated vertically. The ' isotropic centre ' of the field probe (5) was positioned on the horizontal centre axis of the EUT and spaced 150mm to the left hand side of the EUT front panel. REPORT NO:2437 PROJECT REF:E7026 REVISION STATUS:Ol ISSUE DA TE:O 1/03/94 SHEET 5 OF 9 Electrostatic Dischal1!e The EUT was re-positioned on the standard dielectric table (2) which was placed on top table (1). An aluminium sheet 0. 3rnm thick was interposed between the two tables and connected directly to the screened room earth reference point. The ESD generator grounding strap was also connected to the earth reference point. ,... REPORT NO:2437 PROJECT REF:E7026 REVISION STATUS:Ol ISSUE DATE: 0 1/03194 SHEET 6 OF 9 TEST METHOD: . ,: " A computer controlled transmitting device was used to transmit a NA VTEX test signal to the EUT during radio frequency tests and after each electrostatic discharge event. The print out was then examined for errors which may be attributed to either type of interference source. The RF signal measured at the receive antenna was checked to be within acceptable limits , ego in the range 20 to 35dB~v. Measured value for the test configuration = 27dB~v. Spot frequency checks were undertaken at 2. 072MHz, 4. 144MHz , 7.372l\1Hz , 14.7456MHz and 66. 348MHz. Conducted RF Immunity Method as defined by IEC801- A cornmon mode RF disturbance was applied in conformity with the test plan, ie. equivalent to radiated field of 10 Vim; swept signal was amplitude modulated to a depth of 80% at kHz in the frequency range O. 15 to SOl\1Hz; exclude…

Text truncated - open the document above for the full version.

REPORT ON Type Approval Testing of the ICS NA V- 5 NA VTEX Receiver (Serial Nos. 100 and 101) in accordance with ETS 300 065 Report No 102151 February 1993 i. MSf1~ TEST REPORT REFERENCE.. 102151 PAGE 1 OF Assessment Services Limited !M~~ Segensworth Road Titchfield Fareham Hampshire England PO I 5 SRH Telephone: 0329443300 Fax: 0329 443421 REPORT ON: Type Approval Testing of the ICS NA V- 5 NA VTEX Receiver (Serial Nos. 100 and 101) in accordance with ETS 300 065I ' Report No. 102151 , . PREPARED FOR: ICS Electronics Ltd. Unit V , Rudford Industrial Estate Ford, Arundel West Sussex BN18 OBD DISTRIBUTION: ICS Electronics Ltd Mr P Martinez Copy No. DTI Waterloo Bridge House Mr J Poole Copy No. Assessment Services Limited Copy No. r ' L , COpy NO. \ 'C:" " ',', TEST REPORT REFERENCE ,. 102151 PAGE 2 OF 43 APPLICANT' S DETAILS CATEGORY OF APPLICANT (Please tick relevant box) (a) (-/ Manufacturer (b) Importer (c) Distributor r ' (d) Agent If box (b), (c) or (d) is ticked complete details in box below with respect to the manufacturer. Company Name: ICS Electronics Inc Address: Unit V, Rudford Industrial Estate Ford , Arundel West Sussex BN18 OBD Name for Contact Purposes: Mr Peter Martinez Telephone No: 090373- 1101 Fax No :090373- 1105 Telex No : MANUFACTURER' S DETAILS Company Name: Address: Name for Contact Purposes: Telephone No : Fax No : Telex No : TEST REPORT REFERENCE.. 102151PAGE 3 OF 43 TYPE DESIGNATION (1) The type designation may be either a single alphanumeric code an alphanumeric code divided into two parts, Please fill in EITHER: Type Designation as a single alphanumeric codeIN/A/V/-151 I I I I I I OR: Type Designation in two parts: 1. Equipment Series No (2) - ("Model Number AND 2. Equipment Specific No (3) - (" Identification Number (1) This is the manufacturers numeric or alphanumeric code or name that is specific to a particular equipment. It may contain information in coded form on the characteristics of the equipment e. frequency, power. The manufacturer is free to choose the form of the type designation. (2)This is the number, code or trade name used by the manufacturer to describe a series or ' family ' of equipment of substantially the same mechanical and electrical construction which will include a number of related equipments. This number is often referred to as the" model number (3) This is the manufacturers identification number given to a specific equipment in the series or ' family of equipments, it is often referred to as the "identification number ( . TYPE APPROVAL TO OTHER ETS Has the equipment been previously type approved to other ETS? Yes (-/ J ETS No. .....,........,....,...........,. Give details of previous type approvals to the equipment: ......"""..."....".,.....,..."",....,.,.,......"........,."...""".,.",."....,..,..........., TEST REPORT REFERENCE.. 102151PAGE 4 OF 43 TECHNICAL CHARACTERISTICS OF THE NA VTEX RECEIVER PART Frequencies: (-/ 1st 518kHz 2nd ... kHz 3rd .., kHz Method of Frequency Generation: ( -/ …

Text truncated - open the document above for the full version.