LJPNKC-1Single-Band Dual-Mode Cellular Telephone

NOKIA CORPORATION Nokia Mobile Phones Elektroniikkatie 10 FIN-90570 OULU FINLAND Tel. +358 7180 08000 Fax. +358 7180 47222 February 27, 2002 Federal Communications Commission Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD. 21046 Attention: Equipment Authorization Branch PER: 47 CFR 22.919 RE: FCC ID: LJPNKC-1 The Electronic Serial Number (ESN) for each transceiver is unique. The ESN host component is permanently attached to a main circuit board of the alterable. The ESN is isolated from fraudulent contact and tampering. The host component does not contain other information, it is not removable and its electrical connections are not accessible. The host component does contain other information, and the ESN information is encoded using: (1) Multiplication or division by a polynomial. (2) Cyclic coding. (3) The spreading of ESN bits over various non-sequential memory locations. The ESN is factory set and is not alterable, transferable, removable, or otherwise able to be manipulated. Cellular mobile equipment is designed such that any attempt to remove, tamper with, or change the ESN chip, its logic system, or firmware originally programmed by the manufacturer will render the mobile transmitter inoperative. NOKIA CORPORATION Mikko Halttunen Product Program Manager, PC Site Oulu NOKIA CORPORATION Nokia Mobile Phones Elektroniikkatie 10 FIN-90570 OULU FINLAND Tel. +358 7180 08000 Fax. +358 7180 47222 February 27, 2002 Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD. 21046 Attention: Equipment Authorization Branch We hereby certify that the transceiver FCC ID: LJPNKC-1 complies with OET Bulletin No. 53 as referenced in Section 22.915 of the Commission’s rules and with EIA/TIA/IS-54-B and TIA/EIA-136 Mobile Station - Land Station Compatibility Standards. Compliance was determined by testing appropriate parameters according to standards. Extensive field testing has been performed in several locations in the USA to verify the compatibility against different systems. NOKIA CORPORATION Mikko Halttunen Product Program Manager, PC Site Oulu NOKIA CORPORATION Nokia Mobile Phones Elektroniikkatie 10 FIN-90570 OULU FINLAND Tel. +358 7180 08000 Fax. +358 7180 47222 February 27, 2002 Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road Columbia, MD. 21046 Attention: Equipment Authorization Branch We hereby certify that the transceiver FCC ID: LJPNKC-1 fully complies with 47CFR22.921. Nokia has received approval for its alternate 911 call completion method (DA 00-132 released January 28, 2000) and has incorporated the required modifications. NOKIA CORPORATION Mikko Halttunen Product Program Manager Nokia Mobile Phones, PC Site Oulu

NOKIA CORPORATION Nokia Mobile Phones Elektroniikkatie 10 FIN-90570 OULU FINLAND Tel. +358 7180 08000 Fax. +358 7180 47222 February 27, 2002 Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD. 21046 Attention: Equipment Authorization Branch REQUEST FOR CONFIDENTIALITY Pursuant to Sections 0.457 (d) (l) (ii) and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of some of the information accompanying this Application of FCC ID: LJPNKC-1 and as outlined below: - Exhibit 4: Block Diagram - Exhibit 5: Schematic Diagrams - Exhibit 10: List of Active Devices and Tune-Up Procedure - Exhibit 12: Theory of Operation / Description of Circuitry These materials contain trade secrets and proprietary information not customarily released to the public and the public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457 (d) (l) (ii) disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this Application. NOKIA CORPORATION Mikko Halttunen Product Program Manager, PC Site Oulu

10 April 2002 RE: FCC ID: LJPNKC-1 SAR 1. Crest factor is defined in the DASY3 system as the relation between peak power and average power of a signal. These factors are commonly used in RF exposure testing. For example in the AMPS mode peak power is equal to average power resulting crest factor of 1. In operating modes, where time frame is divided into several slots, crest factor is 1/duty cycle (IS-136-> 3, GSM-> 8) EMC 1. Presented data was preprocessed to save some space in test report. Measured field strength values for tested device and substitution antenna are presented in the table below. Mode Frequency, MHz Field strength level dBuV/m, LJPNKW-1, E T Field strength level dBuV/m, substitution antenna, E S 824.04 87.8 63.3 836.40 85.7 60.2 AMPS 848.97 88.0 62.3 824.04 93.2 67.8 836.40 90.3 64.7 TDMA-800 848.97 92.8 67.8 Level column shows conducted RF power fed into substitution antenna. 2. Amended test report page has been uploaded as a new exhibit.

RESPONSE 1 (2) Response to FCC correspondence 4119 FCC ID: LJPNKC-1 Applicant: Nokia Corporation Copyright © 2002 Nokia. All rights reserved. To: Martin Perrine FCC Equipment Authorization Branch Re: FCC ID: LJPNKC-1 Applicant: Nokia Corporation Correspondence Reference Number: 4119 731 Confirmation Number: TC504953 A) Please address how the burst nature of the emission was account for in the radiated and conducted emission measurements. All spectrum analyzer measurement were done using peak detector and duty cycle was used during power meter measurements. B) Discussion of how the EUT was operated/controlled during the test to assure the testing of all appropriate modes, maximum power, and any duty factor driven parameters. Supplement C Appendix B part I 2. Special control software was used allowing control over frequency, mode and power level of EUT. Modulation, duty cycle or any other system specified fixed parameters cannot be affected and they were the same than in normal operation. All EMC and RF exposure tests are done using this software. C) Please provide a full parts list. New confidentiality request is included to cover also parts list. D) Please confirm that the CSM-6 is the only body-worn accessory available for this phone. Please update the manual to mention this accessory. CSM-6 is the only provided body-worn accessory, which can be used with headset (i.e. have a call when worn on body). However, CSL-20 is provided as well, but it does not have space/hole for headset connector (located on the bottom of the phone). These accessories will be listed in Accessory section of the user manual. Picture 1. CSL-20 horizontal carrying case Updated text in manual: For body worn operation, this phone has been tested and meets the FCC RF exposure guidelines when used with the Nokia accessories supplied or designated for this product. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. RESPONSE 2 (2) Response to FCC correspondence 4119 FCC ID: LJPNKC-1 Applicant: Nokia Corporation Copyright © 2002 Nokia. All rights reserved. Added items into Accessory section: Carry case (CSM-6) Handsome leather case helps protect your phone and allows for easy keypad access. The clip attaches to your belt for convenience. (shown at right) Carry case (CSL-20) Luxurious, hard leather case with a flap and convenient clip that attaches to your belt. E ) Please provide SAR plots with the operating mode of the radio, i.e. AMPs or TDMA. We will do this in all future submissions, but request that this time these modes are identified with following information: - AMPS plots are always the first ones in every operating position and can be identified of crest factor of 1.0 - TDMA plots can be identified of crest factor of 3.0 We apologize for any inconvenience this may have caused. F) Discussion of how the EUT was operated/controlled during the test to assure the testing of all appropriate modes, maximum power, and any duty factor driven parameters. Supplement C Appendix B part I 2. Look above B)

NOKIA CORPORATION Nokia Mobile Phones Elektroniikkatie 10 FIN-90570 OULU FINLAND Tel. +358 7180 08000 Fax. +358 7180 47222 May 10, 2002 Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD. 21046 Attention: Equipment Authorization Branch REVISED REQUEST FOR CONFIDENTIALITY Pursuant to Sections 0.457 (d) (l) (ii) and 0.459 of the Commission’s Rules, the Applicant hereby requests confidential treatment of some of the information accompanying this Application of FCC ID: LJPNKC-1 and as outlined below: - Exhibit 4: Block Diagram - Exhibit 5: Schematic Diagrams - Exhibit 10: List of Active Devices, Tune-Up Procedure and Parts List - Exhibit 12: Theory of Operation / Description of Circuitry These materials contain trade secrets and proprietary information not customarily released to the public and the public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457 (d) (l) (ii) disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this Application. NOKIA CORPORATION Mikko Halttunen Product Program Manager, PC Site Oulu

1 Mar 2002 Exhibit 3: External Photographs FCC ID: LJPNKC-1 Applicant: Nokia Corporation Copyright © 2002 Nokia Corporation 1 Mar 2002 Exhibit 3: External Photographs FCC ID: LJPNKC-1 Applicant: Nokia Corporation Copyright © 2002 Nokia Corporation

Applicant: Nokia CorporationCopyright2002 Nokia Corporation FCC ID: LJPNKC-1 MADE IN USA ESN: Code: 0507069 FCC ID: LJPNKC-1 IC: 661E-NKC1 Type: NKC-1 Model: Exhibit 1: Type Label Position 27 Feb 2002 MADE IN USA ESN: Code: 0507069 FCC ID: LJPNKC-1 IC: 661E-NKC1 Type: NKC-1 Model: MADE IN USA ESN: Code: 0507069 FCC ID: LJPNKC-1 IC: 661E-NKC1 Type: NKC-1 Model: 27 Feb 2002 Applicant: Nokia CorporationCopyright2002 Nokia Corporation FCC ID: LJPNKC-1 Exhibit 1: Type Label Position NOKIA CORPORATION Nokia Mobile Phones Elektroniikkatie 10 FIN-90570 OULU FINLAND Tel. +358 7180 08000 Fax. +358 7180 47222 February 27, 2002 Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD. 21046 Attention: Equipment Authorization Branch COMPLIANCE STATEMENT OF LJPNKC-1 The compliance statement can be seen in User Guide of LJPNKC-1 because the size of the handportable LJPNKC-1 and its identification label are so small that the compliance statement cannot be printed visible enough. NOKIA CORPORATION Mikko Halttunen Product Program Manager, PC Site Oulu DRAFT The wireless phone described in this guide is approved for use in TDMA and AMPS networks. LEGAL INFORMATION Part No. ________, Issue No. 1 Copyright ©2002 Nokia Corporation. All rights reserved. Nokia is a registered trademark of Nokia Corporation. Printed in Canada __/2002 Nokia, Nokia Connecting People and the Original Accessories logos are trademarks of Nokia Corporation and/or its affiliates. US Patent No 5818437 and other pending patents. T9 text input software Copyright ©1999-2002. Tegic Communications, Inc. All rights reserved. Includes RSA BSAFE cryptographic or security protocol software from RSA Security. The information contained in this user guide was written for Nokia phone [Model]. Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice UNDER NO CIRCUMSTANCES SHALL NOKIA BE RESPONSIBLE FOR ANY LOSS OF DATA OR INCOME OR ANY SPECIAL, INCIDENTAL, AND CONSEQUENTIAL OR INDIRECT DAMAGES HOWSOEVER CAUSED. THE CONTENTS OF THIS DOCUMENT ARE PROVIDED “AS IS.” EXCEPT AS REQUIRED BY APPLICABLE LAW, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY AND RELIABILITY OR CONTENTS OF THIS DOCUMENT. NOKIA RESERVES THE RIGHT TO REVISE THIS DOCUMENT OR WITHDRAW IT AT ANY TIME WITHOUT PRIOR NOTICE. EXPORT CONTROLS This product contains commodities, technology or software exported from the United States in accordance with the Export Administration regulations. Diversion contrary to U.S. law is prohibited. FCC/INDUSTRY CANADA NOTICE Your phone may cause TV or radio interference (for example, when using a telephone in close proximity to receiving equipment). The FCC or Industry Canada can require you to stop using your telephone if such interference cannot be eliminated. If you require assistance, contact your local service facility. This device complies with part 15 of the FCC rules. Operation is subject to the condition that this device does not cause harmful interference.

1 Mar 2002 External 9: Internal Photographs FCC ID: LJPNKC-1 Applicant: Nokia Corporation Copyright © 2002 Nokia Corporation 1 Mar 2002 External 9: Internal Photographs FCC ID: LJPNKC-1 Applicant: Nokia Corporation Copyright © 2002 Nokia Corporation Internal antenna 1 Mar 2002 External 9: Internal Photographs FCC ID: LJPNKC-1 Applicant: Nokia Corporation Copyright © 2002 Nokia Corporation

NOKIA CORPORATION Nokia Mobile Phones Elektroniikkatie 10 FIN-90570 OULU FINLAND Tel. +358 7180 08000 Fax. +358 7180 47222 February 27, 2002 Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road Columbia, MD. 21046 Attention: Equipment Authorization Branch We hereby certify that the transceiver FCC ID: LJPNKC-1 complies with ANSI/IEEE C95.1-1992 Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. Compliance was determined by testing appropriate parameters according to standard. NOKIA CORPORATION Mikko Halttunen Product Program Manager, PC Site Oulu PC Site Oulu Exhibit 11: SAR Report DTX04017-EN Applicant: Nokia Corporation FCC ID: LJPNKC-1 Copyright  2002 Nokia Corporation 1 (14) SAR Compliance Test Report Test report no.: Not numbered Date of report: 2002-03-05 Number of pages: 56 Contact person: Kautio Olli Responsible test engineer: Mäkikyrö Pertti Testing laboratory: Nokia Corporation Elektroniikkatie 10 P.O. Box 50 FIN-90571 OULU Finland Tel. +358-7180-08000 Fax. +358-7180-47222 Client: Nokia Corporation Elektroniikkatie 10 P.O. Box 50 FIN-90571 OULU Finland Tel.+358-7180-08000 Fax. +358-7180-47222 Tested devices: LJPNKC-1 CSM-6 Supplement reports: - Testing has been carried out in accordance with: IEEE P1528-200X Draft 6.4 Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Body Due to Wireless Communications Devices: Experimental Techniques Documentation: The documentation of the testing performed on the tested devices is archived for 15 years at PC Site Oulu Test results: The tested device complies with the requirements in respect of all parameters subject to the test. The test results and statements relate only to the items tested. The test report shall not be reproduced except in full, without written approval of the laboratory. Date and signatures: 2002-03-05 For the contents: Pertti Mäkikyrö Engineering Manager, EMC Miia Nurkkala Test Engineer PC Site Oulu Exhibit 11: SAR Report DTX04017-EN Applicant: Nokia Corporation FCC ID: LJPNKC-1 Copyright  2002 Nokia Corporation 2 (14) CONTENTS 1.SUMMARY FOR SAR TEST REPORT ..........................................................................................................................3 1.1 MAXIMUM RESULTS FOUND DURING SAR EVALUATION.................................................................................................................. 3 1.1.1Head Configuration.......................................................................................................................................................... 3 1.1.2Body Worn Configuration............................................................................................................................................... 3 1.1.3Measurement Uncertainty ............................................................................................................................................. 3 2.DESCRIPTION OF TESTED DEVICE .............................................................................................................................4 2.1 PICTURE OF PHONE AND LOCATION OF ANTENNA............................................................................................................................. 4 2.2 D ESCRIPTION OF THE ANTENNA........................................................................................................................................................ 4 2.3 B ATTERY OPTIONS............................................................................................................................................................................. 4 2.4 B ODY WORN ACCESSORIES.............................................................................................................................................................. 5 3.TEST CONDITIONS ........................................................................................................................................................5 3.1 AMBIENT CONDITIONS...................................................................................................................................................................... 5 3.2 RF CHARACTERISTICS OF THE TEST SITE............................................................................................................................................. 5 3.3 T EST SIGNAL, FREQUENCIES, AND OUTPUT POWER.......................................................................................................................... 5 4.DESCRIPTION OF THE TEST EQUIPMENT.................................................................................................................5 4.1 SYSTEM ACCURACY VERIFICATION.................................................................................................................................................... 6 4.2 T ISSUE SIMULANTS............................................................................................................................................................................ 7 4.2.1Head Tissue Simulant ...................................................................................................................................................... 7 4.2.2Muscle Tissue Simulant................................................................................................................................................... 7 4.3 P HANTOMS........................................................................................................................................................................................ 8 4.4 I SOTROPIC E-FIELD PROBE ET3DV6 ................................................................................................................................................ 8 5.DESCRIPTION OF THE TEST PROCEDURE ....................................…

Text truncated - open the document above for the full version.

FCC ID: LJPNKC-1 MFA p0230002, d0230007 PAGE NO.21 of 72. AMENDED April 10, 2002 MEASUREMENT SUMMARY: Measurement Of Maximum Deviation MODULATION LIMIT, kHz DEVIATION, kHz (a) Voice≥10.8 &≤13.2 10.8 (b) Wideband Data≥7.2 &≤8.8 8.0 (c) SAT≥1.8 &≤2.2 2.1 (d) ST≥7.2 &≤8.8 8.0 (e) SAT + VOICE N/A 11.0 (f) SAT + DTMF N/A 10.8 (i) NAMPS VOICE N/A N/A (j) NAMPS DSAT N/A N/A (k) NAMPS ST N/A N/A (l) NAMPS VOICE N/A N/A PERFORMED BY: Doug Noble, B.A.S. E.E.T.