LKT-IF-24WLAN

BreezeACCESS 2.4 Base Station Equipment Installation Manual Revision 3 November, 2000 Cat. No. 213125 Front Matter BS Equipment Installation ManualiiBreezeACCESS 2.4 Series © 2000 by BreezeCOM Ltd. All rights reserved. No part of this publication may be reproduced in any material form without the written permission of the copyright owner. Trade Names BreezeACCESS, BreezeNET, BreezeLINK, BreezeVIEW, BreezeMANAGE and WIX are trade names of BreezeCOM Ltd. Other brand and product names are registered trademarks or trademarks of their respective companies. Statement of Conditions The information contained in this manual is subject to change without notice. BreezeCOM shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual or equipment supplied with it. Warranty In the following warranty text, “the Company” shall mean: • BreezeCOM Ltd., for products located outside the USA. • BreezeCOM Inc., for products located in the USA. This BreezeACCESS product is warranted against defects in material and workmanship for a period of one year from date of purchase. During this warranty period the Company will, at its option, either repair or replace products that prove to be defective. For warranty service or repair, the product must be returned to a service facility designated by the Company. Authorization to return products must be obtained prior to shipment. The buyer shall pay all shipping charges to the Company and the Company shall pay shipping charges to return the product to the buyer. The Company warrants that the firmware designed by it for use with the unit will execute its programming instructions when properly installed on the unit. The Company does not warrant that the operation of the unit or firmware will be uninterrupted or error-free. Front Matter BreezeACCESS 2.4 SeriesiiiBS Equipment Installation Manual Limitations of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the buyer, buyer supplied interfacing, unauthorized modification or misuse, operation outside of the environmental specifications for the product, or improper site preparation or maintenance. No other warranty is expressed or implied. The Company specifically disclaims the implied warranties of merchantability and fitness for any particular purpose. BreezeCOM shall not be liable to any person for any special or indirect damages, including, but not limited to, loss of profits or revenues, loss of use or damage to any associated equipment, cost of capital, cost of substitute products, facilities or services, downtime costs or claims resulting from any cause whatsoever arising from or in any way connected with the manufacture, sale, handling, service, repair, maintenance or use of the products. In no event shall the company’s liability exceed the purchase price denoted on the invoice. Electronic Emission Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for digital equipment, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. Information to User Any changes or modifications of equipment not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Safety Considerations For the following safety considerations, “Instrument” means the BreezeACCESS Base Station equipment components and cables. Front Matter BS Equipment Installation ManualivBreezeACCESS 2.4 Series RF Warning To comply with FCC RF exposure requirements in section 1.1307, a minimum separation distance of 2m (79 inches) is required between the antenna and all persons. Line Voltage Before connecting this instrument to the power line, make sure that the voltage of the power source matches the requirements of the instrument. Radio The instrument transmits radio energy during normal operation. To avoid possible harmful exposure to this energy, do not stand or work for extended periods of time in front of its antenna. The long-term characteristics or the possible physiological effects of Radio Frequency Electromagnetic fields have not been yet fully investigated. Antenna Installation and Grounding Be sure that the Outdoor unit, the antenna and the supporting structure are properly installed to eliminate any physical hazard to either people or property. Verify that the antenna mast is grounded so as to provide protection against voltage surges and static charges. Make sure that the installation of the outdoor unit, antenna and cables is performed in accordance with all relevant national and local building and safety codes. BreezeACCESS 2.4 SeriesvBS Equipment Installation Manual Table of Contents 1. INTRODUCTION ..................................................................................................................... 1 2. BASIC INSTALLATION ......................................................................................................... 2 2.1 Packing List – Modular Shelf Equipment ............................................................................. 2 2.1.1 BS-SH Base Station Shelf...........................…

Text truncated - open the document above for the full version.

BreezeACCESS 2.4 Subscriber Units SU-A-2.4 Series SU-E-2.4 Series Installation Manual Preliminary Revision 3 November, 2000 Cat. No. 213123 Front Matter SU-A/E Subscriber Units Installation ManualiiBreezeACCESS 2.4 Series © 2000 by BreezeCOM Ltd. All rights reserved. No part of this publication may be reproduced in any material form without the written permission of the copyright owner. Trade Names BreezeACCESS, BreezeNET, BreezeLINK, BreezeVIEW, BreezeMANAGE and WIX are trade names of BreezeCOM Ltd. Other brand and product names are registered trademarks or trademarks of their respective companies. Statement of Conditions The information contained in this manual is subject to change without notice. BreezeCOM shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this manual or equipment supplied with it. Warranty In the following warranty text, “the Company” shall mean: • BreezeCOM Ltd., for products located outside the USA. • BreezeCOM Inc., for products located in the USA. This BreezeACCESS product is warranted against defects in material and workmanship for a period of one year from date of purchase. During this warranty period the Company will, at its option, either repair or replace products that prove to be defective. For warranty service or repair, the product must be returned to a service facility designated by the Company. Authorization to return products must be obtained prior to shipment. The buyer shall pay all shipping charges to the Company and the Company shall pay shipping charges to return the product to the buyer. The Company warrants that the firmware designed by it for use with the unit will execute its programming instructions when properly installed on the unit. The Company does not warrant that the operation of the unit or firmware will be uninterrupted or error-free. Limitations of Warranty The foregoing warranty shall not apply to defects resulting from improper or inadequate maintenance by the buyer, buyer supplied interfacing, unauthorized modification or misuse, operation outside of the environmental specifications for the product, or improper site preparation or maintenance. No other warranty is expressed or implied. The Company specifically disclaims the implied warranties of merchantability and fitness for any particular purpose. BreezeCOM shall not be liable to any person for any special or indirect damages, including, but not Front Matter BreezeACCESS 2.4 SeriesiiiSU-A/E Subscriber Units Installation Manual limited to, loss of profits or revenues, loss of use or damage to any associated equipment, cost of capital, cost of substitute products, facilities or services, downtime costs or claims resulting from any cause whatsoever arising from or in any way connected with the manufacture, sale, handling, service, repair, maintenance or use of the products. In no event shall the company’s liability exceed the purchase price denoted on the invoice. Electronic Emission Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for digital equipment, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment notwithstanding use in commercial, business and industrial environments. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Information to User Any changes or modifications of equipment not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Safety Considerations For the following safety considerations, “Instrument” means the BreezeACCESS Subscriber Unit components and its cables . To avoid shock, do not perform any servicing unless you are qualified. RF Warning To comply with FCC RF exposure requirements in section 1.1307, a minimum separation distance of 2m (79 inches) is required between the antenna and all persons. Line Voltage Before connecting this instrument to the power line, make sure that the voltage of the power source matches the requirements of the instrument. Front Matter SU-A/E Subscriber Units Installation ManualivBreezeACCESS 2.4 Series Radio The instrument transmits radio energy during normal operation. To avoid possible harmful exposure to this energy, do not stand or work for extended periods of time in front of its antenna. The long-term characteristics or the possible physiological effects of Radio Frequency Electromagnetic fields have not been yet fully investigated. Antenna Installation and Grounding Be sure that the Outdoor unit, the antenna and the supporting structure are properly installed to eliminate any physical hazard to either people or property. Verify that the antenna mast is grounded so as to provide protection against voltage surges and static charges. Make sure that the installation of the Outdoor unit, antenna and cables is performed in accordance with all relevant national and local building and safety codes. BreezeACCESS 2.4 SeriesvSU-A/E Subscriber Units Installation Manual Table of Contents 1. INTRODUCTION .....................................................................................................................1 2. BASIC INSTALLATION..........................................................................................................4 2.1 Packing List ...........................................................................................................................…

Text truncated - open the document above for the full version.

tel: 650-726-1263 fax: 650-726-1252 [email protected] Thomas N. Cokenias EMC &Radio Approvals Test & Consulting Services for Commercial, Military, International Compliance P.O. Box 1086 El Granada, CA 94018 FCC Laboratory20 April 2001 7435 Oakland Mills Road Columbia, MD 21046 Attention: Application Examiner Reviewing Engineer Re: Request for confidentiality per Section 0.459 of FCC Rules Applicant: Breezecom Ltd. FCC ID: LKT-IF-24 To whom it may concern, Request is hereby submitted, on behalf of my client Breezecom Ltd. to withhold from public review certain portions of the application for equipment certification for the referenced FCC identifier. In particular, the following sections of the application and report are requested to be kept confidential: IDU Block Diagram ODU Block Diagram Indoor Schematic High Power Schematic Rationale for request for confidentiality: Breezecom has invested considerable time and materials in research and development to produce the referenced product. Disclosure of the confidential portions of this application to competitors would give them competitive advantage in developing similar products.  If you have questions or need further information, please contact the undersigned. Sincerely, THOMAS N. COKENIAS tel: 650-726-1263 fax: 650-726-1252 [email protected] EMC Consultant/Agent for Breezecom Ltd.

FCC ID Label and Label Location Applicant: BreezeCom Ltd. FCC ID: LKT-IF-24 Description: 2.4 GHz FHSS Transceiver FCC ID: LKT-IF-24Breezecom Ltd. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may cause undesired operation.

FCC ID Label and Label Location Applicant: BreezeCom Ltd. FCC ID: LKT-IF-24 Description: 2.4 GHz FHSS Transceiver FCC ID: LKT-IF-24Breezecom Ltd. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference that may cause undesired operation.

BreezeCom 2.4GHz System description 1. Overview The BreezeCom 2.4GHz IF outdoor indoor system contains the following blocks: 1. Outdoor radio unit 2. Indoor radio unit. 3. Single coaxial cable connecting the both. The base station outdoor radio unit and the subscriber outdoor radio unit are identical. The indoor unit of the base station and of the subscriber is identical electrical circuits in different casing. The base station is mounted in a 19” rack and the subscriber unit card is mounted in an individual box. The system is a TDD frequency hopping system operating in the full range of the 2.4GHz frequency band from 2400-2484MHz. The system is designed to meet the channel allocation designed for the 2.4GHz range. This is established by applying the frequency hopping ability to cover the entire allocated bandwidth. The system is based on a cellular deployment using either a single center base station unit or several base station units located at the same place creating a sectorial center base station. The subscriber units are located in the user location either as an integrated indoor unit or as a subscriber two box unit with an outdoor unit and a indoor unit connected by a single coax cable. 2. 2.4GHz radio Unit description The 2.4GHz radio unit is connected in one end to a communication 10BaseT port and in the other end is a 26dBm power output transceiver unit with a 15dBi antennas enabling it to communicate in a bit rate up to 3Mbit/s. The signal flow in transmit mode is as followed. In the indoor unit a 10BaseT data signal is added with control bits and transferred to the modem and the IF section where it is modulated to an 8FSK modulation with a carrier frequency of 440MHz with a bandwidth of about 1.6MHz (Occupied band width 99%). This signal is then transferred to the outdoor unit were it is unconverted to the 2400-2484MHz ranges according to the selected channel using a hop synthesizer that is set to the correct channel assignment. The unconverted signal is then amplified to about 26dBm and is fed to a Tx/Rx switch. In transmit mode the Tx/Rx switch is set to transmit connecting the power amplifier output to the antenna. The signal flow in the receive mode is as followed. The signal is received by an antennas on the out door unit and is feed through the Tx/Rx switch to a LNA. The received signal is then amplified by a LNA and down converted to 440MHz IF. On the same coaxial cable that used in transmit mode the outdoor unit sends the 440MHz IF received signal to the indoor unit. This IF frequency is filtered by a 440MHz SAW filter and is applied to a discriminator for detection. The detected signal is then feed to propriety ASIC for final detection and converted to the 10BaseT signal that is the output of the unit at the user side. 3. Base Station Unit The base station units come in two basic configurations. One configuration is a stand- alone base station unit that is identical to a subscriber unit constructed from an outdoor unit and a single indoor unit the second configuration is a sectorial based base station that can apply up to 6 indoor and outdoor base station units using a single 19” rack established to hold up to 6 base station indoor units and 48V power supplies. Each of the 6 indoor base station units is then connected to an outdoor unit through a single coaxial cable carrying on it 440MHz IF signal, 12V DC power to the outdoor unit and control signals from the indoor unit to the outdoor unit. In both cases the signal flow is similar due to the fact that the 19” base station rack and the stand-alone base station box are the same units in a different PCB from the RF and Modem aspect. The difference between the two is the power supply in each unit.

Indoor Antennas OMNI-6 OMNI-6, IndoorOmni-directional Antenna The OMNI-6, 6 dBi, omnidirectional antenna can be used withthe and for long rangeindoor applications. BreezeNET PRO.11 D Model BridgesDS.11 Outdoor Bridges The OMNI-6 antenna attaches to the female connector on thePRO.11 D Model Bridges and the DS.11 Outdoor Bridges and provides 360 degree horizontal/20degree vertical transmission. Click toview BreezeNET PRO.11 Range Table. Click here to view the BreezeNET DS.11 Range Table. here SPECIFICATIONS Antenna: Antenna Gain*6 dBi Kit Gain! 5 dBi Frequency Range2.4 – 2.5 GHz Impedance50 Ohms Dispersion360° horizontal/20° vertical PolarizationVertical VSWR1.5:1 Max Dimensions10.5" x 0.75"; 38 x18mm tubular Operating temperature range-86° to 158° F; -30° to 70° C Weight4 oz; 100 g MountingWall, standard Cable: TypeRG-58 Impedance50 Ohms Attenuation0.2 dB (ft.); Length4’ ConnectorN type * Antenna gain is the gain of the antennawithout the cable. ! Kit gain is the actual gain of the antenna kit as it isshipped from BreezeCOM. Back to Antennas & Accessories || || || || || || || || || || || || HomeAbout BreezeCOMProductsApplicationsNews and Events Ordering and TrackingTechnical SupportPartnersSiteMapContact Us ©Copyrighted BreezeCOM® All Rights Reserved 11/15/00 10:28 PMBreezeCOM - OMNI-6, Indoor Omni-directional Antenna Page 1 of 1http://www.breezecom.com/Products/Antennas/omni6_outdoor.htm

Outdoor Antennas OMNI-8 OMNI-8, Outdoor Directional Antenna The OMNI-8, 8-dBi, omni directional antenna can be usedwith the BreezeNET PRO.11 D Model Bridges and DS.11 Outdoor Bridges. It is used foroutdoor, multipoint links that need 360 degree dispersion pattern. The OMNI-8 antenna attaches to the female connector on thePRO.11 D Model Bridges and the DS.11 Outdoor Bridges and provides 360 degree horizontal/13degree vertical transmission. Click toview BreezeNET PRO.11 Range Table. here SPECIFICATIONS Antenna: Antenna Gain*8 dBi Kit Gain! 6 dBi Frequency Range2.4 to 2.5 GHz Impedance50 Ohms Dispersion360° horizontal/13° vertical PolarizationVertical VSWR< 1.5:1 Dimensions17" length; 43 cm Operating temperature range-100° to 185° F; -40° to 85°C Wind load @ 125 mph5.53 lbs; 2.5 kg Weight.45 lbs; 205 g MountingWall and mast L bracket, 2"mast Cable: TypeLMR 400 Length20’ ConnectorProprietary SMA male Attenuation1.4 dB (ft.) Impedance50 Ohms * Antenna gain is the gain of the antennawithout the cable. ! Kit gain is the actual gain of the antenna kit as it is shipped from BreezeCOM. Back to Antennas & Accessories || || || || || || || || || || || || HomeAbout BreezeCOMProductsApplicationsNews and Events Ordering and TrackingTechnical SupportPartnersSiteMapContact Us ©Copyrighted BreezeCOM® All Rights Reserved 11/15/00 10:27 PMBreezeCOM - OMNI-8, Outdoor Directional Antenna Page 1 of 1http://www.breezecom.com/Products/Antennas/omni8_outdoor.htm

Outdoor Antennas UNI-16 UNI-16,Outdoor Directional Antenna The UNI-16, 16 dBi,directional antenna can be used with the and . It is primarily designed for medium to long range transmission froma remote site to a mulitpoint link. It is ideal for applications requiring low profile,high gain antennas. BreezeNET PRO.11D Model Bridges DS.11 OutdoorBridges The UNI-16 antenna attaches tothe female connector on the PRO.11 D Model Bridges and the DS.11 Outdoor Bridges andprovides 28 degree horizontal/28 degree vertical transmission. Click to view BreezeNET PRO.11 Range Table. Clickto view the BreezeNET DS.11 Range Table. here here SPECIFICATIONS Antenna: Antenna Gain*16 dBi Kit Gain! 14 dBi Frequency Range2.4 to 2.5 GHz Impedance50 Ohms Dispersion28° horizontal/28° vertical PolarizationVertical or horizontal VSWR1.5:1 Front to back ratio> 40 dB Cross polarity rejection> 30 dB Dimensions11" x 11" x 3.5";280 x 280 x 89 mm Operating temperature range-86° to 158° F; -30° to 70° C Wind loading40 lbs @ 100 mph; 18 kg @ 160kmph Weight2 lbs; .91 kg HousingHigh impact ABS plastic MountingMast, standard; wall, optional Cable: TypeLMR 400 Length30’ ConnectorProprietary SMA male Attenuation2.1 dB Impedance50 Ohms * Antenna gain is the gain of the antennawithout the cable. ! Kit gain is the actual gain of the antenna kit as it is shipped from BreezeCOM. Back to Antennas & Accessories || || || || || || || || || || || || HomeAbout BreezeCOMProductsApplicationsNews and Events Ordering and TrackingTechnical SupportPartnersSiteMapContact Us ©Copyrighted BreezeCOM® All Rights Reserved 11/15/00 10:26 PMBreezeCOM - UNI-16, Outdoor Directional Antenna Page 1 of 1http://www.breezecom.com/Products/Antennas/uni16_outdoor.htm

Outdoor Antennas UNI-24 UNI-24,Outdoor Directional Antenna The UNI-24, 24 dBi,directional antenna can be used with the and . It is primarily designed for long range, outdoor point-to-pointlinks and can achieve ranges of up to eight miles with the PRO.11 D models, and 15 mileswith the DS.11 bridges, using UNI-24s at both ends of the link. BreezeNET PRO.11D Model BridgesDS.11 OutdoorBridges The UNI-24 antenna attaches to the female connector on the PRO.11 D Model Bridges and the DS.11 Outdoor Bridges and provides a six degree horizontal/10 degreevertical transmission. Click to view BreezeNET PRO.11 Range Table. Click to view the BreezeNET DS.11 Range Table. here here SPECIFICATIONS Antenna: Antenna Gain*24 dBi Kit Gain! 19 dBi Frequency Range2.4 to 2.5 GHz Impedance50 Ohms Dispersion7.5° horizontal/7.5° vertical PolarizationVertical or horizontal VSWR1:4:1 Front to back ratio> 31 dB Cross polarity rejection> 26 dB Dimensions24" x 36" x 15";610 x 915 x 381mm Operating temperature range-86° to 158° F; -30° to 70° C Wind loading97 lbs @ 100 mph; 44 kg @ 160 mph Weight5.4 lbs; 2.43 kg HousingMagnesium alloy reflector MountingMast, standard; wall, optional Cable: TypeLMR 400 Length50’ ConnectorProprietary SMA male Attenuation3.5 dB Impedance50 Ohms * Antenna gain is the gain of the antennawithout the cable. ! Kit gain is the actual gain of the antenna kit as it is shipped from BreezeCOM. Back to Antennas & Accessories || || || || || || || || || || || || HomeAbout BreezeCOMProductsApplicationsNews and Events Ordering and TrackingTechnical SupportPartnersSiteMapContact Us ©Copyrighted BreezeCOM® All Rights Reserved 11/15/00 10:25 PMBreezeCOM - UNI-24, Outdoor Directional Antenna Page 1 of 1http://www.breezecom.com/Products/Antennas/uni24_outdoor.htm

MPE Calculations for 2.4 GHz Frequency Hopping Spread Spectrum Applicant: Breezecom Ltd. FCC ID: LKT-IF-24 RF Hazard Distance Calculation mW/cm2 from Table1:1.00 Max RF Power TX Antenna MPE P, dBmG, dBiSafe Distance, cm 12.023.516.8 19.017.017.8 20.015.516.8 26.07.513.3 Basis of Calculations: E^2/3770 = S, mW/cm2 E, V/m = (Pwatts*Ggain*30)^.5/d, meters d = ((Pwatts*G*30)/3770*S))^0.5Pwatts*Ggain = 10^(PdBm-30+GdBi)/10) NOTE: For fixed installations, 2m separation required for TCB certification

001116CB Tom & Thu Breezecom OMNI-8 Antenna EUT Harmonic's Measurement Lowest Channel set @ 1, Fundamental 2.401GHz Freq. ReadingAFCloss Pre-amp DistOtherLevelLimitMarginPolHeight Mark (MHz) (dBuV)(dB)(dB)(dB)dBdB(dBuV/m) FCC_B(dB)(H/V) (Meter) (P/Q/A) 480247.0032.94.231.2520.01.0033.8574.00-40.15V1.0P 4802 42.50 32.9 4.2 31.25 20.0 1.00 29.35 54.00 -24.65 V1.0Av 720345.4037.04.931.2520.01.0037.0574.00-36.95V1.0P 7203 35.80 37.0 4.9 31.25 20.0 1.00 27.45 54.00 -26.55 V1.0Av 960443.7537.86.331.2520.00.0036.6074.00-37.40V1.0P 9604 32.40 37.8 6.3 31.25 20.0 0.00 25.25 54.00 -28.75 V1.0Av 1200045.0039.26.731.2520.01.0040.6574.00-33.35V1.0P 12000 35.00 39.2 6.7 31.25 20.0 1.00 30.65 54.00 -23.35 V1.0Av 1441048.2039.07.731.2520.01.0044.6574.00-29.35V1.0P 1441036.74 39.0 7.7 31.25 20.0 1.00 33.19 54.00 -20.81 V1.0Av 1680749.1045.09.131.2520.00.0051.9574.00-22.05V1.0P 1680738.50 45.0 9.1 31.25 20.0 0.00 41.35 54.00 -12.65 V1.0Av 1921051.6032.310.031.2520.01.0043.6574.00-30.35V1.0P 1921041.20 32.3 10.0 31.25 20.0 1.00 33.25 54.00 -20.75 V1.0Av 2161053.8032.511.231.2520.01.0047.2574.00-26.75V1.0P 2161043.40 32.5 11.2 31.25 20.0 1.00 36.85 54.00 -17.15 V1.0Av 2400053.8532.611.931.2520.00.0047.1074.00-26.90V1.0P 2400042.30 32.6 11.9 31.25 20.0 0.00 35.55 54.00 -18.45 V1.0Av Total data #: 18Peak: RBW=VBW=1MHzOther = High Pass Filter V.2fAverage: RBW=1MHz, VBW=10HzDistance = 20*log(dm/ds) Company: EUT Description: Test Configuration : Type of Test: Mode of Operation: FCC, VCCI, CISPR, CE, AUSTEL, NZ UL, CSA, TUV, BSMI, DHHS, NVLAP 1366 B ORDEA UX DRIVE, SUNNYV ALE , CA 94089 PHONE: (408) 752-8166 FAX: (408) 752-8168 Project #: Report #: Date& Time: Test Engr: A-Site !"#$% A-Site !"#$% B-Site !"#$% B-Site !"#$% C- Site !"#$% C- Site !"#$% F-Site !"#$%& F-Site !"#$%& 6 Worst Data

001116CB Thu Breezecom UNI-24 Antenna EUT Harmonic's Measurement Lowest Channel set @ 1, Fundamental 2.401GHz Freq. ReadingAFCloss Pre-amp DistOtherLevelLimitMarginPolHeight Mark (MHz) (dBuV)(dB)(dB)(dB)dBdB(dBuV/m) FCC_B(dB)(H/V) (Meter) (P/Q/A) 480260.5032.94.231.259.51.0057.8574.00-16.15V1.0P 4802 56.20 32.9 4.2 31.25 9.5 1.00 53.55 54.00 -0.45V1.0Av 720345.2837.04.931.259.51.0047.4374.00-26.57V1.0P 7203 32.80 37.0 4.9 31.25 9.5 1.00 34.95 54.00 -19.05 V1.0Av 960443.0637.86.331.2520.00.0035.9174.00-38.09V1.0P 9604 32.50 37.8 6.3 31.25 20.0 0.00 25.35 54.00 -28.65 V1.0Av 1200044.9539.26.731.2520.01.0040.6074.00-33.40V1.0P 12000 34.90 39.2 6.7 31.25 20.0 1.00 30.55 54.00 -23.45 V1.0Av 1441048.3239.07.731.2520.01.0044.7774.00-29.23V1.0P 1441036.80 39.0 7.7 31.25 20.0 1.00 33.25 54.00 -20.75 V1.0Av 1680748.6645.09.131.2520.00.0051.5174.00-22.49V1.0P 1680738.30 45.0 9.1 31.25 20.0 0.00 41.15 54.00 -12.85 V1.0Av 1921051.5032.310.031.2520.01.0043.5574.00-30.45V1.0P 1921040.20 32.3 10.0 31.25 20.0 1.00 32.25 54.00 -21.75 V1.0Av 2161053.6932.511.231.2520.01.0047.1474.00-26.86V1.0P 2161043.20 32.5 11.2 31.25 20.0 1.00 36.65 54.00 -17.35 V1.0Av 2400053.7632.611.931.2520.00.0047.0174.00-26.99V1.0P 2400042.20 32.6 11.9 31.25 20.0 0.00 35.45 54.00 -18.55 V1.0Av Total data #: 18Peak: RBW=VBW=1MHzOther = High Pass Filter V.2fAverage: RBW=1MHz, VBW=10HzDistance = 20*log(dm/ds) Company: EUT Description: Test Configuration : Type of Test: Mode of Operation: FCC, VCCI, CISPR, CE, AUSTEL, NZ UL, CSA, TUV, BSMI, DHHS, NVLAP 1366 B ORDEA UX DRIVE, SUNNYV ALE , CA 94089 PHONE: (408) 752-8166 FAX: (408) 752-8168 Project #: Report #: Date& Time: Test Engr: A-Site !"#$% A-Site !"#$% B-Site !"#$% B-Site !"#$% C- Site !"#$% C- Site !"#$% F-Site !"#$%& F-Site !"#$%& 6 Worst Data

001116CB Tom & Thu Breezecom OMNI-8 Antenna EUT Harmonic's Measurement Mid Channel set @ 480, Fundamental 2.44GHz Freq. ReadingAFCloss Pre-amp DistOtherLevelLimitMarginPolHeight Mark (MHz) (dBuV)(dB)(dB)(dB)dBdB(dBuV/m) FCC_B(dB)(H/V) (Meter) (P/Q/A) 488049.8432.94.231.259.51.0047.1974.00-26.81V1.0P 4880 46.90 32.9 4.2 31.25 9.5 1.00 44.25 54.00 -9.75V1.0Av 732046.2037.04.931.259.51.0048.3574.00-25.65V1.0P 7320 35.50 37.0 4.9 31.25 9.5 1.00 37.65 54.00 -16.35 V1.0Av 976043.5237.86.331.2520.00.0036.3774.00-37.63V1.0P 9760 32.50 37.8 6.3 31.25 20.0 0.00 25.35 54.00 -28.65 V1.0Av 1220044.8939.26.731.2520.01.0040.5474.00-33.46V1.0P 12200 33.59 39.2 6.7 31.25 20.0 1.00 29.24 54.00 -24.76 V1.0Av 1464048.3539.07.731.2520.01.0044.8074.00-29.20V1.0P 1464037.00 39.0 7.7 31.25 20.0 1.00 33.45 54.00 -20.55 V1.0Av 1708048.5045.09.131.2520.00.0051.3574.00-22.65V1.0P 1708038.60 45.0 9.1 31.25 20.0 0.00 41.45 54.00 -12.55 V1.0Av 1952051.9032.310.031.2520.01.0043.9574.00-30.05V1.0P 1952041.20 32.3 10.0 31.25 20.0 1.00 33.25 54.00 -20.75 V1.0Av 2196054.0032.511.231.2520.01.0047.4574.00-26.55V1.0P 2196043.50 32.5 11.2 31.25 20.0 1.00 36.95 54.00 -17.05 V1.0Av 2440043.8032.611.931.2520.00.0037.0574.00-36.95V1.0P 2440042.70 32.6 11.9 31.25 20.0 0.00 35.95 54.00 -18.05 V1.0Av Total data #: 18Peak: RBW=VBW=1MHzOther = High Pass Filter V.2fAverage: RBW=1MHz, VBW=10HzDistance = 20*log(dm/ds) Company: EUT Description: Test Configuration : Type of Test: Mode of Operation: FCC, VCCI, CISPR, CE, AUSTEL, NZ UL, CSA, TUV, BSMI, DHHS, NVLAP 1366 B ORDEA UX DRIVE, SUNNYV ALE , CA 94089 PHONE: (408) 752-8166 FAX: (408) 752-8168 Project #: Report #: Date& Time: Test Engr: A-Site !"#$% A-Site !"#$% B-Site !"#$%…

Text truncated - open the document above for the full version.