M3N-A3C054339RKE Transceiver

The device under test is manufactured by the grantee (Continental Corporation) and sold as an OEM product. Per 47 CFR 2.909, 2.927, 2.931, 2.1033, 15.15(b) etc..., the grantee must ensure the end-user has all applicable / appropriate operating instructions. When end-user instructions are required, as in the case of this product, the grantee must notify the OEM to notify the end- user. Continental Corporation will supply this document to the reseller/distributor dictating what must be included in the end user’s manual for the commercial product. INFORMATION TO BE INCLUDED IN THE END USER'S MANUAL The following information (in blue) must be included in the end product user’s manual to ensure continued FCC and Innovation, Science and Economic Development Canada’s licence-exempt RSS(s) compliance. The ID numbers must be included in the manual if the device label is not readily accessible to the end user. The compliance paragraphs below must be included in the user's manual. ****************************************************************************** FCC ID: M3N-A3C054339 IC: 7812A-A3C054339 This device complies with Part 15 of the FCC Rules and with Innovation, Science and Economic Development Canada’s licence -exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Note: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met. ******************************************************************************

To Whom lt May Concern Authoritv to Act as Aqent and REL Listinq We appoint Bradley J. Koskion behalf of Wleless Approval Consultants and Joseph D. Brunett on behalf of Willow Run Test Labs and Amber Helm Development, LC to act as our agent in the preparation of this application for equipment certification. We certify that submitted documents properly describe the device or system for which equipment certification is sought. We also certify that each unit manufactured, imported or marketed, as defined in lndustry Canada's regulations will have affixed to it a label identical to that submitted for approval with this application. Further, in accordance with section 6.5 of lC CB-02, we hereby acknowledge that our company's product cannot be distributed, leased or offered for sale in Canada until it's listed on the lndustry Canada Radio Equipment List (REL). For instances where our authorized agent signs the application for certification on our behalf, we acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by American Certification Body, lnc. and/or TUV Rheinland Group and/or Vista Laboratories, /nc. still resides with Gontinental Automotive Systems US lnc. For TCB applications, we certify that we are not subject to denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988,21 U.S.C. 862. Further, no party, as defined in 47 CFR 1 .2002 (b), to the application is subject to denial of federal benefits, that includes FCC benefits. We also declare that the information provided to the FCC is true and correct to the best of our knowledge (47 CFR 2.911(d)) and we have been informed of the grantee responsibilities (47 CFR 2.909) regarding certified equipment. Dated 12February 2020 Signature: Name: Title: email: On behalf of Telephone Muma Homologation Engineer for the Americas Charles.M [email protected] Continental Automotive Systems US lnc. 4685Investment Drive Troy, Michigan 48098 United States of America +,t 249 764 6793

Willow Run (WR) Test Labs, Inc. 7117 Fieldcrest Dr., Brighton, Michigan 48116 USA Tel: (734) 252-9785, Fax: (734) 926-9785, e-mail: [email protected] Re: Certification for Continental Automotive FCC ID: M3N-A3C054339 IC: 7812A-A3C054339 REQUEST FOR CONFIDENTIALITY Pursuant to USA FCC 47 CFR 0.457(d) and 0.459 and Canada IC RSP-100, Section 10, Continental Automotiverequests that a part of the subject application be held confidential. Continental Automotive has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to ”competition” would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Exhibit Conf. TypeRational Exh 04 - Block DiagramPermanentIncludes proprietary internal oscillator frequency information. Exh 05 - SchematicsPermanentIncludes proprietary design information Exh 10 - BOM + PlacementPermanentIncludes proprietary design information Permanent Confidentiality:Continental Automotive requests that any exhibits listed above as permanently confidential be permanently withheld from public review. Short-Term Confidentiality (FCC Only):Continental Automotive requests that any exhibits selected above as short term confidential be withheld from public view for a period of days (noted above) from the date of the Grant of Equipment Authorization and prior to marketing. If there are any questions regarding the application or testing performed, please contact us at the above address or call (734) 252-9785, or e-mail [email protected]. Sincerely, Joseph D. Brunett Willow Run (WR) Test Labs, Inc. 9

Willow Run (WR) Test Labs, Inc. 7117 Fieldcrest Dr., Brighton, Michigan 48116 USA Tel: (734) 252-9785, Fax: (734) 926-9785, e-mail: [email protected] Attn.:Certification and Engineering Bureau, Innovation, Science and Economic Development Canada 3701 Carling Avenue, Bldg. 94 Ottawa, Ontario K2H 8S2 Re: Certification for Continental Automotive A3C054339 Series IC: 7812A-A3C054339 If necessary, we have enclosed application materials for certification of Continental Automotive A3C054339 Series. It has been verified to comply with IC RSS-210v10/GENv5. Current Variants: There are eleven (11) minor housing variants of the EUT. All variants employ identical PCBs and circuitry, but the housings vary based on vehicle logo and the number of buttons populated on the housing. Two worst case variants were determined in pretesting, those being the 4-BTN chrome button variant (HVIN: A3C053034) and the 5-BTN chrome button variant (HVIN: A3C055107). If there are any questions regarding the application or testing performed, please contact us at the above address or call (734) 252-9785, or e-mail [email protected]. Sincerely, Joseph D. Brunett Willow Run (WR) Test Labs, Inc. 11 Willow Run (WR) Test Labs, Inc. 7117 Fieldcrest Dr., Brighton, Michigan 48116 USA Tel: (734) 252-9785, Fax: (734) 926-9785, e-mail: [email protected] Attn.:Federal Communications Commission Equipment Approval Services P.O. Box 358315 Pittsburgh, PA 15251-5315 Re: Certification for Continental Automotive A3C054339 Series FCC ID: M3N-A3C054339 If necessary, we have enclosed application materials for certification of Continental Automotive A3C054339 Series. It has been verified to comply with CFR Title 47, Part 15.231. Current Variants: There are eleven (11) minor housing variants of the EUT. All variants employ identical PCBs and circuitry, but the housings vary based on vehicle logo and the number of buttons populated on the housing. Two worst case variants were determined in pretesting, those being the 4-BTN chrome button variant (HVIN: A3C053034) and the 5-BTN chrome button variant (HVIN: A3C055107). If there are any questions regarding the application or testing performed, please contact us at the above address or call (734) 252-9785, or e-mail [email protected]. Sincerely, Joseph D. Brunett Willow Run (WR) Test Labs, Inc. 10

902 MHz 104XXXXX E-SIGN 90000XXX AA RELEASED MY21 FORD PEPS KEY FOB WITH JAMMER AND MOTION SENSOR HOMOLOGATION 21/FEB/20 B.MANRIQUEZ CHANGE NO. E-SIGN INDEX DESCRIPTION DATE (DD/MM/YY) NAME DRAFT 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 RQPNMLKJIHGFEDCB 82.9105-0208.0 / 000 / 00 19 20 21 22 23 24 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 AS ABCDEFGHIJKLMNPQRS BEMERKUNGEN NOTES DRAWING CAD SYSTEMMATERIAL GENERAL TOLERANCES TOLERANCE PRINCIPLE RELEASED BY DEPARTMENT TITLESURFACE (C) Continental AG PAGE of SCALE DEPARTMENT REVIEWED BY DEPARTMENTCALCULATED WEIGHT MATERIAL NO. DOC. VERS. DOC. PART DOC. TYPE DOCUMENT NO. 3D MODELDOC.VERS. CHANGEDITEMS ZONE INGRID CHANGE DESCRIPTION CREATED BY DATEDATEDATE DIMENSIONS IN MILLIMETERS TRANSMITTER HOMOLOGATION INFORMATION - - - - 40964735_CAD_000.CATProduct- - - 41585057 DRW 000 A3C0543350000 -- ASME Y14.5-2018 Size ISO 14405 - - A - 1 9 1:1 g +/- - % ECM NO. FORMAT A0 THE REPRODUCTION, DISTRIBUTION AND UTILIZATION OF THIS DOCUMENT AS WELL AS THE COMMUNICATION OF ITS CONTENTS TO OTHERS WITHOUT EXPRESS AUTHORIZATION IS PROHIBITED. OFFENDERS WILL BE HELD LIABLE FOR THE PAYMENT OF DAMAGES. ALL RIGHTS RESERVED IN THE EVENT OF THE GRANT OF A PATENT, UTILITY MODEL OR DESIGN. NO GUARANTEE CAN BE GIVEN IN RESPECT OF THE TRANSLATION. IN ALL CASES THE LATEST ENGLISH LANGUAGE VERSION OF THIS DOCUMENT SHALL BE TAKEN AS AUTHORITATIVE . . A 0 En curso 41585057_DRW_000.CATDrawing 5B BI-DIR MS7T-15K601-BA MS7T-15K601-BAFCC ID: M3N-A3C054339IC: 7812A-A3C054339C: A3C054339 NORTH AMERICAHOMOLOGATION MARKING FCC STANDARDS 5B BI-DIR ML3T-15K601-BA ML3T-15K601-BAFCC ID: M3N-A3C054339IC: 7812A-A3C054339C: A3C054335 NORTH AMERICAHOMOLOGATION MARKING FCC STANDARDS 5B BI-DIR MR3T-15K601-BA MR3T-15K601-BAFCC ID: M3N-A3C054339IC: 7812A-A3C054339C: A3C054976 NORTH AMERICAHOMOLOGATION MARKING FCC STANDARDS 4B BI-DIR MB5T-15K601-AA MB5T-15K601-AAFCC ID: M3N-A3C054339IC: 7812A-A3C054339C: A3C054343 NORTH AMERICAHOMOLOGATION MARKING FCC STANDARDS 5B BRONCO M1PT-15K601-BB M1PT-15K601-BBFCC ID: M3N-A3C054339IC: 7812A-A3C054339C: A3C039100 NORTH AMERICAHOMOLOGATION MARKING FCC STANDARDS 4B BRONCO M2DT-15K601-CA M2DT-15K601-CAFCC ID: M3N-A3C054339IC: 7812A-A3C054339C: A3C053034 NORTH AMERICAHOMOLOGATION MARKING FCC STANDARDS 902 MHz DRAFT 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 RQPNMLKJIHGFEDCB 82.9105-0208.0 / 000 / 00 19 20 21 22 23 24 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 AS ABCDEFGHIJKLMNPQRS BEMERKUNGEN NOTES DRAWING CAD SYSTEMMATERIAL GENERAL TOLERANCES TOLERANCE PRINCIPLE RELEASED BY DEPARTMENT TITLESURFACE (C) Continental AG PAGE of SCALE DEPARTMENT REVIEWED BY DEPARTMENTCALCULATED WEIGHT MATERIAL NO. DOC. VERS. DOC. PART DOC. TYPE DOCUMENT NO. 3D MODELDOC.VERS. CHANGEDITEMS ZONE INGRID CHANGE DESCRIPTION CREATED BY DATEDATEDATE DIMENSIONS IN MILLIMETERS TRANSMITTER HOMOLOGATION INFORMATION - - - - 40964735_CAD_000.CATProduct- - - 41585057 DRW 000 A3C0543350000 -- ASME Y14.5-2018 Size ISO 14405 - - A - 2 9 1:1 g +/- - % ECM NO. FORMAT A0 THE REPRODUCTION, DISTRIBUTION AND UTILIZATION OF THIS DOCUMENT AS WELL AS THE COMMUNICATION OF ITS CONTENTS TO OTHERS WITHOUT EXPRESS AUTHORIZATION IS PROHIBITED. OFFENDERS WILL BE HELD LIABLE FOR THE PAYMENT OF DAMAGES. ALL RIGHTS RESERVED IN THE EVENT OF THE GRANT OF A PATENT, UTILITY MODEL OR DESIGN. NO GUARANTEE CAN BE GIVEN IN RESPECT OF THE TRANSLATION. IN ALL CASES THE LATEST ENGLISH LANGUAGE VERSION OF THIS DOCUMENT SHALL BE TAKEN AS AUTHORITATIVE . . A 0 En curso 41585057_DRW_000.CATDrawing 5B BI-DIR MT4T-15K601-CA MT4T-15K601-CAFCC ID: M3N-A3C054339IC: 7812A-A3C054339 C: A3C055101 NORTH AMERICAHOMOLOGATION MARKING FCC STANDARDS 5B BI-DIR ML1T-15K601-BA ML1T-15K601-BAFCC ID: M3N-A3C054339IC: 7812A-A3C054339C: A3C055107 NORTH AMERICAHOMOLOGATION MARKING FCC STANDARDS 5B BI-DIR MR3V-15K601-AA MR3V-15K601-AAFCC ID: M3N-A3C054339IC: 7812A-A3C054339 C: A3C054980 NORTH AMERICAHOMOLOGATION MARKING FCC STANDARDS 5B BI-DIR ML7T-15K601-BA NORTH AMERICAHOMOLOGATION MARKING FCC STANDARDS ML7T-15K601-BAFCC ID: M3N-A3C054339IC: 7812A-A3C054339C: A3C054349 5B BI-DIR MF3T-15K601-BA MF3T-15K601-BAFCC ID: M3N-A3C054339IC: 7812A-A3C054339C: A3C054346 NORTH AMERICAHOMOLOGATION MARKING FCC STANDARDS

The 2017 PEPS bidirectional system consists of an RF transceiver integrated into the key which includes an RF receiver and transmitter. The antenna is common between the RF transmitter and the RF receiver. The RF transmitter is used to transmit information to the receiver in the vehicle for locking, unlocking, opening the trunk, starting the vehicle, and Panic function. The RF receiver in the bidirectional key is used to receive the engine status information from the vehicle. RF messages can be transmitted by one of two means. The keypad on the key can be used for locking, unlocking, unlocking the trunk, panic, and remote start. Lifting the door handle or pushing the start button in the vehicle will generate an LF field, which the key will respond to with a RF transmission to unlock or start the vehicle.

Amber Helm Development L.C. 92723 Michigan Hwy-152 Sister Lakes, Michigan 49047 USA Tel: 888-847-8027 EMC Test Report CON02-WR2005TX Issued:February 22, 2020 regarding USA: CFR Title 47, Part 15.231(Emissions) Canada:IC RSS-210v10/GENv5(Emissions) for A3C054339 Series Category: RKE Transmitter Judgments: 15.231 / RSS-210v10 Compliant Testing Completed: February 22, 2020 TESTING NVLAP LAB CODE 200129-0 Prepared for: Continental Automotive 4685 Investment Drive, Troy Michigan 48098 USA Phone: +1 (248) 764-6783, Fax: +1 (248) 764-7281 Contact: Charles Muma, [email protected] Data Recorded by: Reviewed by: Dr. Joseph Brunett, EMC-002790-NEGordon Helm, EMC-002401-NE Prepared by:Date of Issue: February 22, 2020 Dr. Joseph Brunett, EMC-002790-NE A copy of this report will remain on file until March 2030.Page 1 of 19 Date: February 22, 2020Prepared For: Continental AutomotiveReport No.: CON02-WR2005TX Revision History Rev. No.DateDetailsRevised By r0February 22, 2020Initial Release.J. Brunett r1March 2, 2020Clarify samples.J. Brunett Contents Revision History2 Table of Contents2 1 Test Report Scope and Limitations4 1.1 Laboratory Authorization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.2 Report Retention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.3 Subcontracted Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.4 Limitation of Results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.5 Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.6 Endorsements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 1.7 Test Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 1.8 Traceability and Equipment Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 2 Test Specifications and Procedures6 2.1 Test Specification and General Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 3 Configuration and Identification of the Equipment Under Test7 3.1 Description and Declarations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 3.1.1EUT Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3.1.2Modes of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3.1.3Variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3.1.4Test Samples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3.1.5Functional Exerciser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3.1.6Modifications Made . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3.1.7Production Intent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3.1.8Declared Exemptions and Additional Product Notes . . . . . . . . . . . . . . . . . . . . . . . .8 4 Emissions9 4.1 General Test Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 4.1.1Radiated Test Setup and Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 4.1.2Conducted Emissions Test Setup and Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4.1.3Power Supply Variation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 4.2 Intentional Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.2.1Fundamental Emission Pulsed Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4.2.2Fundamental Emission Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.2.3Fundamental Emission Field Strength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.3 Unintentional Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.3.1Transmit Chain Spurious Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.3.2Radiated Digital Spurious . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5 Measurement Uncertainty and Accreditation Documents19 Amber Helm Development L.C., 92723 Michigan Hwy-152, Sister Lakes, Michigan 49047 USAPage 2 of 19 Date: February 22, 2020Prepared For: Continental AutomotiveReport No.: CON02-WR2005TX List of Tables 1Test Site List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 2Equipment List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 3EUT Declarations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 4Fundamental Emission Pulsed Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5Fundamental Emission Bandwidth.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6Fundamental Emission Field Strength.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 7Transmit Chain Spurious Emissions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 8Measurement Uncertainty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 List of Figures 1Photos of EUT.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 2EUT Test Configuration Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 3Radiated Emissions Diagram of the EUT. . . . . . . . . . . . . . . . …

Text truncated - open the document above for the full version.