M5LMLSC1DUO Magnetless SPD/CAD Sensor

sigmasport.com SIGMA-ELEKTRO GmbH Dr.-Julius-Leber-Straße 15 67433 Neustadt, Germany 000000 / 1 DUO MAGNETLESS CADENCE Industry Canada Statement This device complies with Industry Canada licence-exempt RSS standard. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d‘Industrie Canada applicables aux appareils radio exempts de licence. L‘exploitation est autorisée aux deux conditions suivantes : (1) l‘appareil ne doit pas produire de brouillage, et (2) l‘utilisateur de l‘appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d‘en compromettre le fonctionnement. IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0.5 cm between the radiator and your body. Cet équipement est conforme aux CNR-102 d‘Industrie Canada. Cet équipement doit êtreinstallé et utilisé avec une distance minimale de 20 centimètres entre le radiateur et votrecorps. Cet émetteur ne doit pas être co-localisées ou opérant en conjonction avec autreantenne ou émetteur. Les antennes utilisées pour cet émetteur doivent être installés et fournir une distance de séparation d‘au moins 0.5 centimètre de toute personne et doit pas être co-située ni fonctionner en conjonction avec une autre antenne ou émetteur. DUO MAGNETLESS SPEED Art.-Nr. 021010 O-RINGS Art.-Nr. 090022 ZUBEHÖR/ACCESORIES CE Statement Battery typeCR 2032 x 3 V Operation temperature-20 °C to 60 °C Operation frequencyANT+ 2.4 GHz @ 1 dBm nominal Bluetooth 2.4 GHz @ 1 dBm nominal Transmission power0~4 dBm Water ratingIPX7 EN You can find the CE declaration at: ce.sigmasport.com/duomagnetlesscadence DE Die CE-Erklärung kann hier eingesehen werden: ce.sigmasport.com/duomagnetlesscadence FR La déclaration CE peut être consultée ici : ce.sigmasport.com/duomagnetlesscadence IT La dichiarazione CE è consultabile qui: ce.sigmasport.com/duomagnetlesscadence ES Encontrarás la declaración de conformidad CE en: ce.sigmasport.com/duomagnetlesscadence NL Je kunt de CE-verklaring hier inzien: ce.sigmasport.com/duomagnetlesscadence PL Deklarację CE znajdziesz tutaj: ce.sigmasport.com/duomagnetlesscadence CZ CE prohlášení najdeš pod následujícím odkazem: ce.sigmasport.com/duomagnetlesscadence 1 3 4 5 2 Remove sticker. ! Blue light flashes. ! Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices). FCC Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance of at least 0.5 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. sigmasport.com DUO MAGNETLESS CADENCE Art.-Nr. 021011 O-RINGS Art.-Nr. 090022 SIGMA-ELEKTRO GmbH Dr.-Julius-Leber-Straße 15 67433 Neustadt, Germany 000000 / 1 ZUBEHÖR/ACCESORIES DUO MAGNETLESS SPEED Industry Canada Statement This device complies with Industry Canada licence-exempt RSS standard. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d‘Industrie Canada applicables aux appareils radio exempts de licence. L‘exploitation est autorisée aux deux conditions suivantes : (1) l‘appareil ne doit pas produire de brouillage, et (2) l‘utilisateur de l‘appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d‘en compromettre le fonctionnement. CE Statement IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with minimum d…

Text truncated - open the document above for the full version.

Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 2 of 22 External Photos Speed Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 3 of 22 Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 4 of 22 Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 5 of 22 Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 6 of 22 Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 7 of 22 Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 8 of 22 Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 9 of 22 Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 10 of 22 Cadence Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 11 of 22 Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 12 of 22 Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 13 of 22 Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 14 of 22 Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 15 of 22

SIGMA ZA5D(SOLO) CAD&SPD Artwork 2012-10 by.Richard PANTONE NUMBER M A D E I N T A I W A N PANTONE Cool Gray 7C IC:7580A-MLSC1 FCC ID:M5LMLSC1 MODEL: MLSC1

Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 16 of 22 Internal Photos Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 17 of 22 Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 18 of 22

Registration num ber: W6M22012-20529-C-1 FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Page 16 of 32 3.2 Equivalent isotropic radiated power FCC Rule: 15.247(b)(3) EIRP = max. conducted output power + antenna gain BLE EIRP=1.38 dBm + (3.48 dBi [antenna gain claimed by manufacturer]) = 4.86 dBm = 3.06 mW ANT+ EIRP =1.24 dBm + (3.48 dBi [antenna gain claimed by manufacturer]) =4.72 dBm = 2.96 mW 3.3 Exemption Limits for Routine Evaluation according to FCC KDB Publication RESULT: Test standard : FCC KDB Publication 447498 D01 General RF Exposure Guidance v06 According to 447498 D01 General RF Exposure Guidance v06: SAR evaluation, by measurement or numerical simulation, is not required when the corresponding SAR Exclusion Threshold condition, listed below, is satisfied. 3.3.1 Exemption Limits for Routine Evaluation – SAR Evaluation SAR evaluation is required if the separation distance between the user and/or bystander and the antenna and/or radiating element of the device is less than or equal to 20 cm, except when the device operates at or below the applicable output power level (adjusted for tune-up tolerance) for the specified separation distance defined in Table . Table: SAR evaluation — Exemption limits for routine evaluation based on frequency and separation distance BLE MHz 5 10 15 20 25 mm 2402 10.09 19.26 29.35 38.52 48.52 SAR Test Exclusion Threshold (mW) MHz 30 35 40 45 50 mm 2402 57.70 67.79 77.87 87.05 97.13 SAR Test Exclusion Threshold (mW) Output power level shall be the higher of the maximum conducted or equivalent isotropically radiated power (e.i.r.p.) source-based, time-averaged output power. Established separation distance is 5 mm. BLE Operating frequency band : 2402-2480 MHz Max. output power level at 5 mm separation distance at 2402 MHz according to table is: 10.09 mW The product is exempt from SAR Evaluation/Testing because the output power of 3.06 mW is below the exemption limit of 10.09 mW. Registration num ber: W6M22012-20529-C-1 FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Page 17 of 32 ANT+ MHz 5 10 15 20 25 mm 2457 9.99 18.98 28.97 37.96 47.95 SAR Test Exclusion Threshold (mW) MHz 30 35 40 45 50 mm 2457 56.94 66.93 76.91 85.91 95.90 SAR Test Exclusion Threshold (mW) Output power level shall be the higher of the maximum conducted or equivalent isotropically radiated power (e.i.r.p.) source-based, time-averaged output power. Established separation distance is 5 mm. ANT+ Operating frequency band : 2457 MHz Max. output power level at 5 mm separation distan ce at 2457 MHz acco rding to table is: 9.99 mW The product is exempt from SAR Evaluation/Testing because the output power of 2.96 mW is below the exemption limit of 9.99 mW.

of Applicant: ZEITBIKE LLC Address: 298 Dalton Street, Ventura, California, United States 93003 1539 Tested and Prepared by Worldwide Testing Services (Taiwan) Co., Ltd. FCC Registration No.: TW1477, TW0020, TW1072 Industry Canada filed test laboratory Reg. No.: 20037 Report No.: W6M22012-20529-C-1 6F, NO. 58, LANE 188, RUEY-KUANG RD., NEIHU TAIPEI 114, TAIWAN, R.O.C. TEL: 886-2-66068877 FAX: 886-2-66068879 E-mail: [email protected] 47 CFR PART 15 SUBPART C TEST REPORT for DUO Magnetless SPD/CAD Sensor Model No.: MLSC1 FCC ID: M5LMLSC1 Registration num ber: W6M22012-20529-C-1 FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Page 1 of 32 TABLE OF CONTENTS 1 GENERAL INFORMATION .......................................................................................................... 2 1.1 N OTES .......................................................................................................................................... 2 1.2 T ESTING LABORATORY ................................................................................................................ 3 1.2.1 Location .................................................................................................................................. 3 1.2.2 Details of accreditation status ................................................................................................ 3 1.3 D ETAILS OF APPROVAL HOLDER ................................................................................................... 3 1.4 A PPLICATION DETAILS ................................................................................................................. 3 1.5 GENERAL INFORMATION OF TEST ITEM ........................................................................................ 4 1.6 TEST STANDARDS ......................................................................................................................... 5 2 TECHNICAL TEST ......................................................................................................................... 6 2.1 S UMMARY OF TEST RESULTS ........................................................................................................ 6 2.2 TEST ENVIRONMENT .................................................................................................................... 6 2.3 T EST EQUIPMENT LIST ................................................................................................................. 7 2.4 GENERAL TEST PROCEDURE ...................................................................................................... 10 3 TEST RESULTS (ENCLOSURE) ................................................................................................ 12 3.1 PEAK OUTPUT POWER (TRANSMITTER) ...................................................................................... 13 3.2 EQUIVALENT ISOTROPIC RADIATED POWER ................................................................................ 16 3.3 EXEMPTION LIMITS FOR ROUTINE EVALUATION ACCORDING TO FCC KDB PUBLICATION ....... 16 3.4 T RANSMITTER RADIATED EMISSIONS IN RESTRICTED BANDS .................................................... 18 3.5 SPURIOUS EMISSIONS (TX) ......................................................................................................... 19 3.6 RADIATED EMISSION ON THE BAND EDGE .................................................................................. 21 3.7 M INIMUM 6 DB BANDWIDTH ..................................................................................................... 24 3.8 P EAK POWER SPECTRAL DENSITY ............................................................................................. 27 3.9 RADIATED EMISSION FROM RECEIVER PART ............................................................................. 30 3.10 P OWER LINE CONDUCTED EMISSION ......................................................................................... 31 APPENDIX.............................................................................................................32 Registration number: W6M22012-20529-C-1 FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Page 2 of 32 1 General Information 1.1 Notes The purpose of conformity testing is to increase the probability of adherence to the essential requirements or conformity specifications, as appropriate. The complexity of the technical specifications, however, means that full and thorough testing is impractical for both technical and economic reasons. Furthermore, there is no guarantee that a test sample which has passed all the relevant tests conforms to a specification. Neither is there any guarantee that such a test sample will interwork with other genuinely open systems. The existence of the tests nevertheless provides the confidence that the test sample possesses the qualities as maintained and that is performance generally conforms to representative cases of communications equipment. The test results of this test report relate exclusively to the item tested as specified in 1.5. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the Worldwide Testing Services(Taiwan) Co., Ltd. Tester: February 18, 2021 Robert Ren Date WTS-Lab. Name Signature Technical responsibility for area of testing: February 18, 2021 Kevin Wang Date WTS Name Signature Registration number: W6M22012-20529-C-1 FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Page 3 of 32 1.2 Testing laboratory 1.2.1 Location OATS No.5-1, Lishui, Shuang Sing Village, Wanli Dist., New Taipei City 207, Taiwan (R.O.C.) 3 meter semi-anechoic chamber No.35, Aly. 21, Ln. 228, Ankang Rd., Neihu Dist., Taipei City 114, Taiwan (R.O.C.) TEL:886-2-6613-0228 FAX:886-2-2791-5046 Company Worldwide Testing Services(Taiwan) Co., Ltd. 6F, NO. 58, LANE 188, RUEY-KUANG RD. NEIHU, TAIPEI 114, TAIWAN R.O.C. Tel : 886-2-66068877 Fax…

Text truncated - open the document above for the full version.

Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 19 of 22 Set Up Photo of Radiated Emission EMI Below 1 GHz Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 20 of 22 Above 1 GHz Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 21 of 22 RF Below 1 GHz Registration number: W6M22012-20529-FCC FCC ID: M5LMLSC1 Worldwide Testing Services(Taiwan) Co., Ltd. Appendix page 22 of 22 Above 1 GHz