M82-EKI-6331AN802.11a/n Wireless Access Point/Client Bridge

EKI-6331AN_User Manual_for NCC Page i IEEE 802.11a/n Wireless Access Point/ Client Bridge User Manual EKI-6331AN_User Manual_for NCC Page ii EKI-6331AN_User Manual_for NCC Page iii Copyright The documentation and the software included with this product are copyrighted 2011 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights of third parties, which may result from its use. Acknowledgements Intel and Pentium are trademarks of Intel Corporation. Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp. All other product names or trademarks are properties of their respective owners. EKI-6331AN_User Manual_for NCC Page iv Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as a consequence of such events. Because of Advantech′s high quality-control standards and rigorous testing, most of our customers never need to use our repair service. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty period. For out-of-warranty repairs, you will be billed according to the cost of replacement materials, service time and freight. Please consult your dealer for more details. If you think you have a defective product, follow these steps: 1. Collect all the information about the problem encountered. (For example, CPU speed, Advantech products used other hardware and software used, etc.) Note anything abnormal and list any onscreen messages you get when the problem occurs. 2. Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available. 3. If your product is diagnosed as defective, obtain an RMA (return merchandize authorization) number from your dealer. This allows us to process your return more quickly. 4. Carefully pack the defective product, a fully-completed Repair and Replacement Order Card and a photocopy proof of purchase date (such as your sales receipt) in a shippable container. A product returned without proof of the purchase date is not eligible for warranty service. 5. Write the RMA number visibly on the outside of the package and ship it prepaid to your dealer. EKI-6331AN_User Manual_for NCC Page v Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To avoid the possibility of exceeding radio frequency exposure limits, you shall beep a distance of at least 35cm between you and the antenna of the installed equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. EKI-6331AN_User Manual_for NCC Page vi Technical Support and Assistance Step 1. Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Step 2. Contact your distributor, sales representative, or Advantech’s customer service center for technical support if you need additional assistance. Please have the following information ready before you call: - Product name and serial number - Description of your peripheral attachments - Description of your software (operating system, version, application software, etc.) - A complete description of the problem - The exact wording of any error messages Safety Instructions 1. Read these safety instructions carefully. 2. K…

Text truncated - open the document above for the full version.

SPORTON International Inc. PAGE NUMBER : A1 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 Photographs of EUT SPORTON International Inc. PAGE NUMBER : A2 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A3 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A4 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 Adapter 1 Brand Name: TOUCH ELECTRONIC CO., LTD. Model No.: SA06-30S12R-V SPORTON International Inc. PAGE NUMBER : A5 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 Adapter 2 Brand Name: OEM Model No.: ADS10-W 150080 SPORTON International Inc. PAGE NUMBER : A6 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A7 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A8 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255

Label s size: 66.3*441.3mm

SPORTON International Inc. PAGE NUMBER : A1 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 Photographs of EUT SPORTON International Inc. PAGE NUMBER : A2 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A3 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A4 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A5 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A6 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A7 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255 SPORTON International Inc. PAGE NUMBER : A8 OF A8 TEL : 886-2-2696-2468 ISSUED DATE : May 26, 2011 FAX : 886-2-2696-2255

Report No.: FR151827 FCC ID: M4Y-ZCN1523H516V2 Page No. : 1 of 3 Appendix B. Maximum Permissible Exposure Report No.: FR151827 FCC ID: M4Y-ZCN1523H516V2 Page No. : 2 of 3 1. Maximum Permissible Exposure 1.1. Applicable Standard Systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy levels in excess limit for maximum permissible exposure. In accordance with 47 CFR FCC Part 2 Subpart J, section 2.1091 this device has been defined as a mobile device whereby a distance of 1 m normally can be maintained between the user and the device. (A) Limits for Occupational / Controlled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-3.0 614 1.63 (100)* 6 3.0-30 1842 / f 4.89 / f (900 / f)* 6 30-300 61.4 0.163 1.0 6 300-1500 F/300 6 1500-100,000 5 6 (B) Limits for General Population / Uncontrolled Exposure Frequency Range (MHz) Electric Field Strength (E) (V/m) Magnetic Field Strength (H) (A/m) Power Density (S) (mW/ cm²) Averaging Time |E|²,|H|² or S (minutes) 0.3-1.34 614 1.63 (100)* 30 1.34-30 824/f 2.19/f (180/f)* 30 30-300 27.5 0.073 0.2 30 300-1500 F/1500 30 1500-100,000 1.0 30 Note: f = frequency in MHz ; *Plane-wave equivalent power density 1.2. MPE Calculation Method E (V/m) ＝ d GP30 Power Density: Pd (W/m²) ＝ 377 2 E E ＝ Electric field (V/m) P ＝ Peak RF output power (W) G ＝ EUT Antenna numeric gain (numeric) d ＝ Separation distance between radiator and human body (m) The formula can be changed to Pd ＝ 2 377 30 d GP   From the peak EUT RF output power, the minimum mobile separation distance, d=0.35m, as well as the gain of the used antenna, the RF power density can be obtained. Report No.: FR151827 FCC ID: M4Y-ZCN1523H516V2 Page No. : 3 of 3 1.3. Calculated Result and Limit For 5GHz ISM Band: Antenna Type : Patch Antenna Max Conducted Power for IEEE 802.11a: 25.54 dBm Antenna Gain (dBi) Antenna Gain (numeric) Peak Output Power (dBm) Peak Output Power ( mW ) Power Density (S) (mW/cm²) Limit of Power Density (S) (mW/cm²) Test Result 15 31.6228 25.5400 358.0944 0.735990 1 Complies

SPORTON International Inc. No. 52, Hwa Ya 1st Rd., Kwei-Shan Hsiang, TaoYuan Hsien, Taiwan, R.O.C. Ph: 886-3-327-3456 / FAX: 886-3-327-0973 / www.sporton.com.tw Report Format Version: 01 FCC RADIO TEST REPORT Applicant’s company Advantech Co., Ltd. Applicant Address No.1, Alley 20, Lane 26, Rueiguang Road, NeiHu District, Taipei 114, Taiwan FCC ID M82-EKI-6331AN Manufacturer’s company Advantech Co., Ltd. Manufacturer Address No.1, Alley 20, Lane 26, Rueiguang Road, NeiHu District, Taipei 114, Taiwan Product Name IEEE 802.11 a/n Wireless Access Point/Client Bridge Brand Name ADVANTECH Model Name EKI-6331AN Test Rule Part(s) 47 CFR FCC Part 15 Subpart C § 15.247 Test Freq. Range 5725 ~ 5850MHz Received Date Jul. 19, 2010 Final Test Date Aug. 04, 2010 Submission Type Original Equipment Statement Test result included is only for the IEEE 802.11n and IEEE 802.11a (5725 ~ 5850MHz) of the product. The test result in this report refers exclusively to the presented test model / sample. Without written approval of SPORTON International Inc., the test report shall not be reproduced except in full. The measurements and test results shown in this test report were made in accordance with the procedures and found in compliance with the limit given in ANSI C63.4-2003 and 47 CFR FCC Part 15 Subpart C. The test equipment used to perform the test is calibrated and traceable to NML/ROC. Report No.: FR151827 Report Format Version: 01 Page No. : i of ii FCC ID: M82-EKI-6331AN Issued Date : May 26, 2011 Table of Contents 1. CERTIFICATE OF COMPLIANCE .......................................................................................................... 1 2. SUMMARY OF THE TEST RESULT ........................................................................................................ 2 3. GENERAL INFORMATION ................................................................................................................... 3 3.1. Product Details ................................................................................................................................................................. 3 3.2. Accessories ...................................................................................................................................................................... 5 3.3. Table for Filed Antenna .................................................................................................................................................... 5 3.4. Table for Carrier Frequencies ........................................................................................................................................... 6 3.5. Table for Test Modes ....................................................................................................................................................... 7 3.6. Table for Testing Locations .............................................................................................................................................. 7 3.7. Table for Supporting Units ............................................................................................................................................... 8 3.8. Table for Parameters of Test Software Setting .................................................................................................................. 8 3.9. Test Configurations ......................................................................................................................................................... 9 4. TEST RESULT .................................................................................................................................. 12 4.1. AC Power Line Conducted Emissions Measurement ........................................................................................................12 4.2. Maximum Conducted Output Power Measurement .........................................................................................................16 4.3. Power Spectral Density Measurement .............................................................................................................................23 4.4. 6dB Spectrum Bandwidth Measurement ..........................................................................................................................28 4.5. Radiated Emissions Measurement ..................................................................................................................................33 4.6. Band Edge Emissions Measurement ................................................................................................................................47 4.7. Antenna Requirements ...................................................................................................................................................51 5. LIST OF MEASURING EQUIPMENTS ................................................................................................... 52 TEST LOCATION ................................................................................................................................ 54 6. TAF CERTIFICATE OF ACCREDITATION ............................................................................................ 55 APPENDIX A. TEST PHOTOS ........................................................................................................ A1 ~ A5 APPENDIX B. MAXIMUM PERMISSIBLE EXPOSURE ........................................................................... B1 ~ B3 Report No.: FR151827 Report Format Version: 01 Page No. : ii of ii FCC ID: M82-EKI-6331AN Issued Date : May 26, 2011 History of This Test Report Original Issue Date: May 26, 2011 Report No.: FR151827 ■ No additional attachment. □ Additional attachment were issued as following record: Attachment No. Issue Date Description Further, this requirement does not apply to intentional radiators that must be professionally installed. Report No.: FR151827 Report Format …

Text truncated - open the document above for the full version.

Report No.: FR151827 FCC ID: M4Y-ZCN1523H516V2 Page No. : 1 of 5 Appendix A. Test Photos Report No.: FR151827 FCC ID: M4Y-ZCN1523H516V2 Page No. : 2 of 5 1. Photographs of Conducted Emissions Test Configuration Test Mode: Mode 1 FRONT VIEW REAR VIEW Report No.: FR151827 FCC ID: M4Y-ZCN1523H516V2 Page No. : 3 of 5 2. Photographs of Radiated Emissions Test Configuration Test Configuration: 9kHz ~30MHz FRONT VIEW REAR VIEW Report No.: FR151827 FCC ID: M4Y-ZCN1523H516V2 Page No. : 4 of 5 Test Configuration: 30MHz~1GHz Test Mode: Mode 2 FRONT VIEW REAR VIEW Report No.: FR151827 FCC ID: M4Y-ZCN1523H516V2 Page No. : 5 of 5 Test Configuration: Above 1GHz FRONT VIEW REAR VIEW