M82-PWS872FLCOMPUTER

Test Laboratory: BTL Date: 2024/1/30 Bluetooth Frequency: 2402 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 23.0°C; Liquid Temperature: 22.0°C Medium parameters used (interpolated): f = 2402 MHz; σ = 1.699 S/m; ε r = 39.039; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn1486; Calibrated: 2023/6/16 - Probe: EX3DV4 - SN7369; ConvF(7.61, 7.61, 7.61) @ 2402 MHz; Calibrated: 2023/5/22 - Sensor-Surface: 1.4mm (Mechanical Surface Detection (Locations From Previous Scan Used)), Sensor- Surface: 1.4mm (Mechanical Surface Detection) - Phantom: ELI V5.0 (20deg probe tilt); Type: QD OVA 002 AA; Serial: 1240 COMPUTER/Aux Ant/Edge 1/Bluetooth_DH5_Ch0/Area Scan (7x8x1): Measurement grid: dx=12mm, dy=12mm Maximum value of SAR (measured) = 0.207 W/kg COMPUTER/Aux Ant/Edge 1/Bluetooth_DH5_Ch0/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 4.684 V/m; Power Drift = 0.09 dB Peak SAR (extrapolated) = 0.280 W/kg SAR(1 g) = 0.118 W/kg; SAR(10 g) = 0.049 W/kg Smallest distance from peaks to all points 3 dB below = 8.1 mm Ratio of SAR at M2 to SAR at M1 = 42.3% Maximum value of SAR (measured) = 0.214 W/kg Test Laboratory: BTL Date: 2024/1/30 WiFi-2.4GHz Frequency: 2437 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 23.0°C; Liquid Temperature: 22.0°C Medium parameters used (interpolated): f = 2437 MHz; σ = 1.74 S/m; ε r = 38.793; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn1486; Calibrated: 2023/6/16 - Probe: EX3DV4 - SN7369; ConvF(7.61, 7.61, 7.61) @ 2437 MHz; Calibrated: 2023/5/22 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Phantom: ELI V5.0 (20deg probe tilt); Type: QD OVA 002 AA; Serial: 1240 COMPUTER/Main Ant/Edge 2/802.11b_Ch6/Area Scan (7x8x1): Measurement grid: dx=12mm, dy=12mm Maximum value of SAR (measured) = 0.325 W/kg COMPUTER/Main Ant/Edge 2/802.11b_Ch6/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 7.964 V/m; Power Drift = -0.07 dB Peak SAR (extrapolated) = 0.434 W/kg SAR(1 g) = 0.203 W/kg; SAR(10 g) = 0.095 W/kg Smallest distance from peaks to all points 3 dB below = 11 mm Ratio of SAR at M2 to SAR at M1 = 55.4% Maximum value of SAR (measured) = 0.344 W/kg Test Laboratory: BTL Date: 2024/1/ 30 WiFi-2.4GHz Frequency: 2462 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 23.0°C; Liquid Temperature: 22.0°C Medium parameters used: f = 2462 MHz; σ = 1.776 S/m; ε r = 38.725; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn1486; Calibrated: 2023/6/16 - Probe: EX3DV4 - SN7369; ConvF(7.61, 7.61, 7.61) @ 2462 MHz; Calibrated: 2023/5/22 - Sensor-Surface: 1.4mm (Mechanical Surface Detection (Locations From Previous Scan Used)), Sensor- Surface: 1.4mm (Mechanical Surface Detection) - Phantom: ELI V5.0 (20deg probe tilt); Type: QD OVA 002 AA; Serial: 1240 COMPUTER/Aux Ant/Edge 1/802.11b_Ch11/Area Scan (7x8x1): Measurement grid: dx=12mm, dy=12mm Maximum value of SAR (measured) = 1.53 W/kg COMPUTER/Aux Ant/Edge 1/802.11b_Ch11/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 9.544 V/m; Power Drift = -0.03 dB Peak SAR (extrapolated) = 2.37 W/kg SAR(1 g) = 0.999 W/kg; SAR(10 g) = 0.405 W/kg Smallest distance from peaks to all points 3 dB below = 8.1 mm Ratio of SAR at M2 to SAR at M1 = 43.8% Maximum value of SAR (measured) = 1.79 W/kg Test Laboratory: BTL Date: 2024/1/29 WiFi-5GHz Frequency: 5250 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 23.0°C; Liquid Temperature: 22.0°C Medium parameters used (interpolated): f = 5250 MHz; σ = 4.562 S/m; ε r = 37.34; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn1486; Calibrated: 2023/6/16 - Probe: EX3DV4 - SN7369; ConvF(5.17, 5.17, 5.17) @ 5250 MHz; Calibrated: 2023/5/22 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Phantom: ELI V5.0 (20deg probe tilt); Type: QD OVA 002 AA; Serial: 1240 COMPUTER/Main Ant/Edge 2/802.11ac160_Ch50/Area Scan (8x10x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 2.27 W/kg COMPUTER/Main Ant/Edge 2/802.11ac160_Ch50/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=2mm Reference Value = 3.624 V/m; Power Drift = 0.04 dB Peak SAR (extrapolated) = 3.92 W/kg SAR(1 g) = 1.01 W/kg; SAR(10 g) = 0.348 W/kg Smallest distance from peaks to all points 3 dB below = 8.8 mm Ratio of SAR at M2 to SAR at M1 = 53.2% Maximum value of SAR (measured) = 2.36 W/kg Test Laboratory: BTL Date: 2024/1/29 WiFi-5GHz Frequency: 5250 MHz; Duty Cycle: 1:1; Room Ambient Temperature: 23.0°C; Liquid Temperature: 22.0°C Medium parameters used (interpolated): f = 5250 MHz; σ = 4.562 S/m; ε r = 37.34; ρ = 1000 kg/m 3 DASY5 Configuration: - Area Scan Setting: Find Secondary Maximum Within: 2.0 dB and with a peak SAR value greater than 0.0012W/kg - Electronics: DAE4 Sn1486; Calibrated: 2023/6/16 - Probe: EX3DV4 - SN7369; ConvF(5.17, 5.17, 5.17) @ 5250 MHz; Calibrated: 2023/5/22 - Sensor-Surface: 1.4mm (Mechanical Surface Detection) - Phantom: ELI V5.0 (20deg probe tilt); Type: QD OVA 002 AA; Serial: 1240 COMPUTER/Aux Ant/Edge 1/802.11ac160_Ch50/Area Scan (8x10x1): Measurement grid: dx=10mm, dy=10mm Maximum value of SAR (measured) = 1.88 W/kg COMPUTER/Aux Ant/Edge 1/802.11ac160_Ch50/Zoom Scan (7x7x12)/Cube 0: Measurement grid: dx=4mm, dy=4mm, dz=2mm Reference Value = 7.709 V/m; Power Drift = -0.42 dB Peak SAR (extrapolated) = 3.41 W/kg SAR(1 g) = 0.901 W/kg; SAR(10 g) = 0.299 W/kg Smallest distance from peaks to all points 3 dB below = 8 mm Ratio of SAR at M2 to SAR at M1 = 54.5% Maximum value of SAR (measured) = 2.14 W/kg Test Laborator…

Text truncated - open the document above for the full version.

N° 1-6736 Scope available on www.cofrac.fr CERTIFICATE #3478.01 Intel Corporation S.A.S – WRF Lab 425 rue de Goa – Le Cargo B6 - 06600, Antibes, France Tel. +33493001400 / Fax +33493001401 Reference: WRF-DCS-TF-012 Version: 002 Application Date: 07/30/2020 1 of 49 TEST REPORT EUT Description WLAN and BT, 2x2 PCIe M.2 2230 adapter card Brand Name Intel® Wi-Fi 6E AX210 Model Name AX210NGW FCC/IC ID FCCID: PD9AX210NG / IC ID: 1000M-AX210NG Date of Test Start/End 2020-07-22 /2020-08-04 Features 802.11ax, Dual Band, 2x2 Wi-Fi 6 + Bluetooth® 5.2 (see section 5) Applicant Intel Mobile Communications Address 100 Center Point Circle, Suite 200 Columbia, South Carolina 29210 USA Contact Person Steven Hackett Telephone/Fax/ Email [email protected] Reference Standards FCC CFR Title 47 Part 15 C RSS-247 issue 2, RSS-Gen issue 5 A1 (see section 1) Test Report identification 200611-03.TR05 Revision Control Rev. 01 This test report revision replaces any previous test report revision (see section 8) The test results relate only to the samples tested. This report shall not be reproduced, except in full, without the written approval of the laboratory. Reference to accreditation shall be used only by full reproduction of test report. Issued by Reviewed by Zayd OUACHICHA (Test Engineer Lead) Cheiel IN (Technical Manager) Test Report N° 200611-03.TR05 Rev. 01 2 of 49 Table of Contents 1. Standards, reference documents and applicable test methods ......................................................................... 3 2. General conditions, competences and guarantees ............................................................................................. 3 3. Environmental Conditions ...................................................................................................................................... 3 4. Test samples ............................................................................................................................................................ 4 5. EUT Features ............................................................................................................................................................ 5 6. Remarks and comments ......................................................................................................................................... 6 7. Test Verdicts summary ........................................................................................................................................... 6 7.1. BT ....................................................................................................................................................................... 6 8. Document Revision History .................................................................................................................................... 6 Annex A. Test & System Description ....................................................................................................................... 7 A.1 MEASUREMENT SYSTEM ........................................................................................................................................ 7 A.2 TEST EQUIPMENT LIST .......................................................................................................................................... 9 A.3 MEASUREMENT UNCERTAINTY EVALUATION ......................................................................................................... 10 Annex B. Test Results ............................................................................................................................................. 11 B.1 20DB BANDWIDTH AND CARRIER FREQUENCY SEPARATION ................................................................................... 11 B.1.1 Test limits .................................................................................................................................................................. 11 B.1.2 Results tables ............................................................................................................................................................ 11 B.1.3 Results screenshot .................................................................................................................................................... 12 B.2 NUMBER OF HOPPING CHANNELS ......................................................................................................................... 15 B.2.1 Test limits .................................................................................................................................................................. 15 B.2.2 Test procedure .......................................................................................................................................................... 15 B.2.3 Results tables ............................................................................................................................................................ 15 B.3 TIME OF OCCUPANCY (DWELL TIME) .................................................................................................................... 19 B.3.1 Test procedure .......................................................................................................................................................... 19 B.3.2 Results tables ............................................................................................................................................................ 19 B.3.3 Results Screenshot ................................................................................................................................................... 20 B.4 MAXIMUM PEAK OUTPUT POWER ANTENNA GAIN .................................................................................................. 26 B.4.1 Test Limits ...................................................................................................…

Text truncated - open the document above for the full version.

Report No.: BTL-FCCP-1-2302T054B Project No.: 2302T054B Page 1 of 52 Report Version: R00 FCC Radio Test Report FCC ID: M82-PWS872FL Report No. : BTL-FCCP-1-2302T054B Equipment : COMPUTER Model Name : PWS-872FL, PWS-872FLXXXXXXXXXXXXXXXX (where X may be any alphanumeric character , blank or “-”.) Brand Name : Advantech Applicant : Advantech Co., Ltd. Address : No.1, Alley 20, Lane 26, Rueiguang Road, Neihu District, Taipei 11491, Taiwan. Radio Function FCC Rule Part(s) Measurement Procedure(s) Date of Receipt Date of Test Issued Date : Bluetooth : FCC CFR Title 47, Part 15, Subpart C (15.247) : ANSI C63.10-2020 : 2024/3/13 : 2025/11/17 ~ 2025/12/30 : 2026/1/8 The above equipment has been tested and found in compliance with the requirement of the above standards by BTL Inc. Prepared by : Brett Shen, Engineer Approved by : Jerry Chuang, Vice Manager BTL Inc. No.18, Ln. 171, Sec. 2, Jiuzong Rd., Neihu Dist., Taipei City 114, Taiwan Tel: +886-2-2657-3299 Fax: +886-2-2657-3331 Web: www.newbtl.com Service mail: [email protected] Report No.: BTL-FCCP-1-2302T054B Project No.: 2302T054B Page 2 of 52 Report Version: R00 Declaration BTL represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with standards traceable to international standard(s) and/or national standard(s). BTL's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTL assumes no responsibility for the data provided by the Customer, any statements, inferences or generalizations drawn by the customer or others from the reports issued by BTL. This report is the confidential property of the client. As a mutual protection to the clients, the public and ourselves, the test report shall not be reproduced, except in full, without our written approval. BTL’s laboratory quality assurance procedures are in compliance with the ISO/IEC 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. BTL is not responsible for the sampling stage, so the results only apply to the sample as received. The information, data and test plan are provided by manufacturer which may affect the validity of results, so it is manufacturer’s responsibility to ensure that the apparatus meets the essential requirements of applied standards and in all the possible configurations as representative of its intended use. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Please note that the measurement uncertainty is provided for informational purpose only and are not use in determining the Pass/Fail results. Report No.: BTL-FCCP-1-2302T054B Project No.: 2302T054B Page 3 of 52 Report Version: R00 CONTENTS 1 SUMMARY OF TEST RESULTS 5 1.1 TEST FACILITY 6 1.2 MEASUREMENT UNCERTAINTY 6 1.3 TEST ENVIRONMENT CONDITIONS 6 1.4 TABLE OF PARAMETERS OF TEXT SOFTWARE SETTING 6 2 GENERAL INFORMATION 7 2.1 DESCRIPTION OF EUT 7 2.2 TEST MODES 9 2.3 BLOCK DIAGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED 10 2.4 SUPPORT UNITS 11 3 AC POWER LINE CONDUCTED EMISSIONS TEST 12 3.1 LIMIT 12 3.2 TEST PROCEDURE 12 3.3 DEVIATION FROM TEST STANDARD 12 3.4 TEST SETUP 13 3.5 TEST RESULT 13 4 RADIATED EMISSIONS TEST 14 4.1 LIMIT 14 4.2 TEST PROCEDURE 15 4.3 DEVIATION FROM TEST STANDARD 15 4.4 TEST SETUP 15 4.5 EUT OPERATING CONDITIONS 17 4.6 TEST RESULT – 9KHZ TO 30 MHZ 17 4.7 TEST RESULT – 30 MHZ TO 1 GHZ 17 4.8 TEST RESULT – ABOVE 1 GHZ 17 5 OUTPUT POWER TEST 18 5.1 LIMIT 18 5.2 TEST PROCEDURE 18 5.3 DEVIATION FROM STANDARD 18 5.4 TEST SETUP 18 5.5 EUT OPERATION CONDITIONS 18 5.6 TEST RESULTS 18 6 LIST OF MEASURING EQUIPMENTS 19 7 EUT TEST PHOTO 20 8 EUT PHOTOS 20 APPENDIX A AC POWER LINE CONDUCTED EMISSIONS 21 APPENDIX B RADIATED EMISSIONS - 9 KHZ TO 30 MHZ 24 APPENDIX C RADIATED EMISSIONS - 30 MHZ TO 1 GHZ 29 APPENDIX D RADIATED EMISSIONS - ABOVE 1 GHZ 32 APPENDIX E OUTPUT POWER 51 Report No.: BTL-FCCP-1-2302T054B Project No.: 2302T054B Page 4 of 52 Report Version: R00 REVISION HISTORY Report No. Version Description Issued Date Note BTL-FCCP-1-2302T054B R00 Original Report. 2026/1/8 Valid Report No.: BTL-FCCP-1-2302T054B Project No.: 2302T054B Page 5 of 52 Report Version: R00 1 SUMMARY OF TEST RESULTS Test procedures according to the technical standards. Standard(s) Section Description Test Result Judgement Remark 15.207 AC Power Line Conducted Emissions APPENDIX A Pass ------ 15.205 15.209 15.247(d) Radiated Emissions APPENDIX B APPENDIX C APPENDIX D Pass ------ 15.247 (a)(1)(iii) Number of Hopping Frequency NOTE (3) Pass ------ 15.247 (a)(1)(iii) Average Time of Occupancy NOTE (3) Pass ------ 15.247 (a)(1) Hopping Channel Separation NOTE (3) Pass ------ 15.247 (a)(1) Bandwidth NOTE (3) Pass ------ 15.247 (b)(1) Output Power APPENDIX E Pass ------ 15.247(d) Antenna conducted Spurious Emission NOTE (3) Pass ------ 15.203 Antenna Requirement ------ Pass ------ Statement of Conformity The statement of conformity is based on the binary decision rule according to IEC Guide 115 and ILAC G8 "simple acceptance" principle. Without considering measurement uncertainty, its specific risk is less than 50% PFA. (PFA: Probability of False Accept) NOTE: (1) ”N/A” denotes test is not applicable in this Test Report. (2) The report format version is TP.1.1.1. (3) This item is demonstrated to full compliance referring to the test report number 200611-03.TR05 of the integrated module (model name: AX210NGW, FCC ID: PD9AX210NG), according to KDB 996369 D02 Q1 a) 2). (4) The radiated emissions are tested to demonstrate full compliance of both module integrated into the host and host itself. (5) The output power of integrated module have been red…

Text truncated - open the document above for the full version.

Customer:研華 Customer Model No.: Part No.: Product Description: Issue Date:20220317 REV.:A Taiwan Anjie Electronics Co., Ltd 台灣安潔電子股份有限公司 ADD: 1F,No.236,Sec.3,Huanbei Rd.,Jubei City,Hsinchu County,30265,Taiwan 地址:新竹縣竹北市環北路三段236號1樓 TEL: 886-3-5543399 FAX:886-3-5543062 電話:886-3-5543399 傳真:886-3-5543062 承 認 書 APPROVAL SHEET AJDP1J-C0058 Antenna Internal WIFI 6E 1.13/235mm(Gray)IPEX_IV 核准 審核 承辦 Anders 客戶承認用印 安潔承認用印 Table of Contents Item 1. Drawing 2. Test Report -Electrical test -Antenna Gain and Efficiency 3. Material Certifications -Antenna -Connector Frequency Range Impedance V.S.W.R Radiation Gain Type Polarization Connector 2.4G<1.79 5G<3.0 6G<3.0 2.4G<2.26 dBi 5G<1.68 dBi 6G<2.46 dBi I-PEX_IV Mechanical Properties SPECIFICATION 50Ω Omni Vertical 2400~7125MHz PIFA Electrical test Antenna Gain and Efficiency Frequency(MHz) 24002410242024302440245024602470248024902500 Gain (dBi) 0.480.931.231.361.431.411.51.661.751.791.79 Directivity (dBi) 4.414.684.814.84.724.594.64.624.624.584.53 Efficiency (dB) -3.93-3.75-3.57-3.43-3.29-3.18-3.1-2.96-2.87-2.8-2.74 Efficiency (%) 40.4742.2143.9145.3546.8648.0349.0350.651.6752.553.17 Frequency(MHz) 51505250535054505550565057505850592560256125 Gain (dBi) 0.941.021.010.431.131.371.291.681.82.022.46 Directivity (dBi) 4.94.724.874.534.754.854.494.624.754.654.66 Efficiency (dB) -3.96-3.7-3.86-4.11-3.62-3.48-3.19-2.94-2.95-2.63-2.2 Efficiency (%) 40.1942.6341.1538.8443.4444.9347.9450.7850.6654.5960.27 Frequency (MHz)6225632564256525662567256825692570257125 Gain (dBi)1.951.951.731.721.331.510.450.060.150.59 Directivity (dBi)4.264.574.424.724.554.914.054.064.494.75 Efficiency (dB)-2.31-2.62-2.69-3.01-3.22-3.4-3.6-3.99-4.34-4.15 Efficiency (%)58.7654.7253.8650.0547.6645.7143.6539.8936.8438.42 Antenna 3D Pattern

Customer:研華 Customer Model No.: Part No.: Product Description: Issue Date:20220317 REV.:A Taiwan Anjie Electronics Co., Ltd 台灣安潔電子股份有限公司 ADD: 1F,No.236,Sec.3,Huanbei Rd.,Jubei City,Hsinchu County,30265,Taiwan 地址:新竹縣竹北市環北路三段236號1樓 TEL: 886-3-5543399 FAX:886-3-5543062 電話:886-3-5543399 傳真:886-3-5543062 承 認 書 APPROVAL SHEET AJDP1J-B0103 Antenna Internal WIFI 6E 1.13/105mm(Black)IPEX_IV 核准 審核 承辦 Anders 客戶承認用印 安潔承認用印 Table of Contents Item 1. Drawing 2. Test Report -Electrical test -Antenna Gain and Efficiency 3. Material Certifications -Antenna -Connector Frequency Range Impedance V.S.W.R Radiation Gain Type Polarization Connector 2.4G<2.5 5G<3.0 6G<3.0 2.4G<3.08 dBi 5G<3.54 dBi 6G<3.79 dBi I-PEX_IV Mechanical Properties SPECIFICATION 50Ω Omni Vertical 2400~7125MHz PIFA Electrical test Antenna Gain and Efficiency Frequency(MHz) 24002410242024302440245024602470248024902500 Gain (dBi) 1.461.762.022.232.372.462.452.552.732.923.08 Directivity (dBi) 4.724.95.115.315.455.545.555.645.815.976.11 Efficiency (dB) -3.26-3.14-3.09-3.08-3.08-3.08-3.11-3.09-3.08-3.05-3.04 Efficiency (%) 47.2348.549.0849.1949.2449.2348.8949.1449.1649.549.72 Frequency(MHz) 51505250535054505550565057505850592560256125 Gain (dBi) 3.183.543.223.133.132.262.22.882.722.993.19 Directivity (dBi) 6.186.486.165.685.634.834.795.395.135.215.06 Efficiency (dB) -3.01-2.95-2.94-2.55-2.5-2.57-2.58-2.51-2.4-2.21-1.87 Efficiency (%) 50.0450.7650.8855.6456.2255.3255.1956.0657.560.0665.02 Frequency (MHz)6225632564256525662567256825692570257125 Gain (dBi)3.793.413.373.452.972.362.522.752.821.83 Directivity (dBi)5.835.845.786.065.615.15.335.936.135.42 Efficiency (dB)-2.05-2.44-2.41-2.61-2.64-2.73-2.82-3.19-3.32-3.6 Efficiency (%)62.4357.0957.4254.8654.4553.3152.2847.9846.6243.69 Antenna 3D Pattern

Report No.: BTL-FCC SAR-1-2302T054B FCC SAR Test Report FCC ID: M82-PWS872FL Report No. : BTL-FCC SAR-1-2302T054B Equipment : COMPUTER Model Name Brand Name : : PWS-872FL Advantech Applicant : Advantech Co., Ltd. Address : No.1, Alley 20, Lane 26, Rueiguang Road, Neihu District, Taipei 11491, Taiwan. Radio Function : Bluetooth, WLAN 2.4G, WLAN 5G Standard(s) : KDB447498 D04 Interim General RF Exposure Guidance v01 KDB248227 D01 802.11 Wi-Fi SAR v02r02 KDB865664 D01 SAR measurement 100 MHz to 6 GHz v01r04 KDB865664 D02 SAR Reporting v01r02 KDB616217 D04 SAR for laptop and Tablets v01r02 FCC §2.1093 Radiofrequency radiation exposure evaluation: portable devices IEEE C95.1:2019 Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz – 300 GHz. IEEE Std 1528:2013 Recommended Practice for Determining the Peak Spatial-Average Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques Date of Receipt : Nov. 2, 2023 Date of Test : Jan. 29, 2024 ~ Jan. 30, 2024 Issued Date : Jun. 13, 2025 The above equipment has been tested and found in compliance with the requirement of the above standards by BTL Inc. Prepared by : Jerry Chuang, Supervisor Approved by : Peter Chen, Assistant Manager BTL Inc. No.18, Ln. 171, Sec. 2, Jiuzong Rd., Neihu Dist., Taipei City 114, Taiwan Tel: +886-2-2657-3299 Fax: +886-2-2657-3331 Web: www.newbtl.com Project No.: 2302T054B Page 1 of 47 Report Version: R00 Report No.: BTL-FCC SAR-1-2302T054B Declaration BTL represents to the client that testing is done in accordance with standard procedures as applicable and that test instruments used has been calibrated with standards traceable to international standard(s) and/or national standard(s). BTL's reports apply only to the specific samples tested under conditions. It is manufacture’s responsibility to ensure that additional production units of this model are manufactured with the identical electrical and mechanical components. BTL shall have no liability for any declarations, inferences or generalizations drawn by the client or others from BTL issued reports. This report is the confidential property of the client. As a mutual protection to the clients, the public and ourselves, the test report shall not be reproduced, except in full, without our written approval. BTL’s laboratory quality assurance procedures are in compliance with the ISO/IEC 17025 requirements, and accredited by the conformity assessment authorities listed in this test report. BTL is not responsible for the sampling stage, so the results only apply to the sample as received. The information, data and test plan are provided by manufacturer which may affect the validity of results, so it is manufacturer’s responsibility to ensure that the apparatus meets the essential requirements of applied standards and in all the possible configurations as representative of its intended use. Limitation For the use of the authority's logo is limited unless the Test Standard(s)/Scope(s)/Item(s) mentioned in this test report is (are) included in the conformity assessment authorities acceptance respective. Please note that the measurement uncertainty is provided for informational purpose only and are not use in determining the Pass/Fail results. Project No.: 2302T054B Page 2 of 47 Report Version: R00 Report No.: BTL-FCC SAR-1-2302T054B Table of Contents Page 1. GENERAL INFORMATION 6 1.1. GENERAL DESCRIPTION OF EUT 6 2. RF EMISSIONS MEASUREMENT 7 2.1. TEST FACILITY 7 2.2. MEASUREMENT UNCERTAINTY 8 2.3. WLAN ANTENNA INFORMATION: 10 2.4. THE MAXIMUM SAR-1G VALUES 10 2.5. LABORATORY ENVIRONMENT 11 2.6. MAIN TEST INSTRUMENTS 12 3. SAR MEASUREMENTS SYSTEM CONFIGURATION 13 3.1. SAR MEASUREMENT SETUP 13 3.1.1. TEST SETUP LAYOUT 13 3.2. DASY5 E-FIELD PROBE SYSTEM 14 3.2.1. EX3DV4 PROBE SPECIFICATION 14 3.2.2. E-FIELD PROBE CALIBRATION 15 3.2.3. OTHER TEST EQUIPMENT 16 3.2.4. SCANNING PROCEDURE 17 3.2.5. DATA STORAGE AND EVALUATION 18 3.2.6. DATA EVALUATION BY SEMCAD 19 4. TISSUE-EQUIVALENT LIQUID 21 4.1. TISSUE-EQUIVALENT LIQUID INGREDIENTS 21 4.2. TISSUE-EQUIVALENT LIQUID PROPERTIES 22 5. SYSTEM CHECK 23 5.1. DESCRIPTION OF SYSTEM CHECK 23 5.2. DESCRIPTION OF SYSTEM CHECK 24 6. OPERATIONAL CONDITIONS DURING TEST 25 6.1. GENERAL DESCRIPTION OF TEST PROCEDURES 25 6.2. TEST POSITION ANTENNA LOCATION 25 6.3. TEST POSITION OF PORTABLE DEVICES 25 6.4. TEST POSITION 26 6.4.1. BODY TEST CONFIGURATION 26 7. SAR MEASUREMENT VARIABILITY AND UNCERTAINTY 29 7.1. SAR MEASUREMENT VARIABILITY 29 7.2. TEST CONFIGURATION 30 7.2.1. WIFI TEST CONFIGURATION 30 7.2.2 . WLAN 2.4G SAR TEST REQUIREMENTS 32 7.2.3. WLAN 5G SAR TEST REQUIREMENTS 33 7.2.4. OFDM TRANSMISSION MODE AND SAR TEST CHANNEL SELECTION 33 7.2.5 . INITIAL TEST CONFIGURATION PROCEDURE 33 8. CONDUCTED POWER RESULTS 34 8.1. CONDUCTED POWER MEASUREMENTS OF BLUETOOTH 34 Project No.: 2302T054B Page 3 of 47 Report Version: R00 Report No.: BTL-FCC SAR-1-2302T054B 8.2. CONDUCTED POWER MEASUREMENTS OF WI-FI 2.4GHZ BAND 35 8.3. CONDUCTED POWER MEASUREMENTS OF 5G UNII_1 36 8.4. CONDUCTED POWER MEASUREMENTS OF 5G UNII_2A 37 8.5. CONDUCTED POWER MEASUREMENTS OF 5G UNII_2C 38 8.6. CONDUCTED POWER MEASUREMENTS OF 5G UNII_3 39 8.7. SAR TEST RESULTS 40 9. SAR TEST RESULTS 41 9.1. BODY SAR TEST RESULTS 41 10. SIMULTANEOUS TRANSMISSION CONDITIONS 43 10.1. STAND-ALONE SAR TEST EXCLUSION 43 10.2. SIMULTANEOUS TRANSMISSION CONDITIONS 44 10.3. ABOUT BT/WIFI 45 11. TEST LAYOUT 46 Project No.: 2302T054B Page 4 of 47 Report Version: R00 Report No.: BTL-FCC SAR-1-2302T054B REPORT ISSUED HISTORY Report Version Description Issued Date R00 Original Issue. 2025/6/13 Project No.: 2302T054B Page 5 of 47 Report Version: R00 Report No.: BTL-FCC SAR-1-2302T054B 1. GENERAL INFORMATION 1.1. GENERAL DESCRIPTION OF EUT Equipment COMPUTER Model Name PWS-872FL Brand Name Advantech Series Model PWS-872FLXXXXXXXXXXXXXXXX (where X may be any alphanumeric character , blank or “-”.) Model Difference D…

Text truncated - open the document above for the full version.

NO.： Asset No.： E-529 Model No.： D5GHzV2 Cal. Date： February 9, 2021 Equipment： ENA Network Analyzer Serial No.： 1121 Next Cal. Date： February 8, 2024 Temp：23.5 °CR.H.：51% 1IEEE Std 1528-2013 2IEC 62209-2 3KDB865664 Equipment：Manufacturer：Model No.：Serial No.：Cal.Organization：Cal. Date： Power AmplifierEMCIEMC053035980869N/ADecember 7, 2021 Power MeterAnritsuMA2487A6K00004714N/AAugust 15, 2021 Power SensorAnritsuMA2491A34138N/AAugust 15, 2021 Directional Coupler WokenTS-PCC0M-05107090019N/AN/A Signal Generator R & SSMB100A113244N/AAugust 2, 2021 ENA Network Analyzer AgilentE5071CMY46524658N/AMarch 22, 2021 FrequencyItemOriginak Cal. ResultVerified on 2022/1/24DeviationResult Impedance, transformed to feed point(Ω) 48.3Ω-8.2jΩ44.3Ω-5.3jΩ<5ΩPass Return Loss(dB)-21.5-21.65-0.7%Pass SAR Value for 1g(mW/g)8.047.833%Pass SAR Value for 10g(mW/g)2.32.261.7%Pass Impedance, transformed to feed point 50.1Ω-2.4jΩ51.4Ω+2.8jΩ<5ΩPass Return Loss(dB)-32.3-30.45.9%Pass SAR Value for 1g(mW/g)8.268.171.1%Pass SAR Value for 10g(mW/g)2.372.350.8%Pass Impedance, transformed to feed point 52.8Ω-1.7jΩ47.9Ω-1.3jΩ<5ΩPass Return Loss(dB)-30-31.78-5.9%Pass SAR Value for 1g(mW/g)8.538.273.0%Pass SAR Value for 10g(mW/g)2.432.372.5%Pass Impedance, transformed to feed point 53.3Ω+2.8jΩ49.2Ω+3.5jΩ<5ΩPass Return Loss(dB)-27.5-28.83-4.8%Pass SAR Value for 1g(mW/g)8.258.012.9%Pass SAR Value for 10g(mW/g)2.332.272.6%Pass Note： Tester：Technical Director： Equipment Information SAR System Uncertainty： % ，（95% CONFIDENCE LEVEL ，Expanded uncertainty K=2 ） 5.8G 5.2G For Head Tissue 5.3G 5.6G Standard List IEEE Recommended Practice for Determining the Peak Spatial-Averaged Specific Absorpiton Rate(SAR) in the Human Head from Wireless Communication Devices: Measurement Texhniques, June 2013 Procedure to determine the Specific Absorption Rate (SAR) for wireless communication devices used in close proximity to the human body(frequency range of 30 MHz to 6 GHz), March 2010 SAR Measurement Requirements for 100 MHz to 6 GHz Dipole Internal Calibration Record Environmental condition： Impedance Test-Head Return Loss-Head NO.： Asset No.： E-529 Model No.： D5GHzV2 Cal. Date： February 9, 2021 Equipment： ENA Network Analyzer Serial No.： 1221 Next Cal. Date： February 8, 2024 Temp：23.6°CR.H.：49% 1IEEE Std 1528-2013 2IEC 62209-2 3KDB865664 Equipment：Manufacturer：Model No.：Serial No.：Cal.Organization：Cal. Date： Power AmplifierEMCIEMC053035980869N/A N/A Power MeterAnritsuMA2495A112800…

Text truncated - open the document above for the full version.