M9H189355073Bluetooth Hands-Free Kit MyCK100

MyCK100 handsfree kit User Guide Introduction MyCK100 handsfree kit is a handsfree kit based on Bluetooth® technology. Bluetooth® technology is a standard for wireless, short range communication. Devices such as a handsfree kit and a mobile phone can communicate together without wires within an approximately 10 m radius. MyCK100 handsfree kit is a Bluetooth® approved handsfree kit, in accordance with 1.2 revision of Bluetooth® protocol. Two profiles are supported: headset & handsfree, so devices supporting either headset or handsfree profile can be used with this handsfree kit. In order to check compatibility of Bluetooth® devices with MyCK100 handsfree kit, please log on to: www.s agem.com/mobiles . This guide focuses on MyCK100 handsfree kit usage with Bluetooth® mobile phone, which is the most common application. Your MyCK100 handsfree kit allows you to receive phone calls, make phone calls (if your handset supports voice-activated features) and set up call volume and ring volume directly on your handsfree kit. MyCK100 handsfree kit is fitted with the following keys below: • A main push button § • A volume cutting wheel • A microphone cutting wheel • Two buttons button 1 (Logo ON/OFF) and button 2 (Logo Mute) (These buttons are used for pairing etc...) Before starting using MyCK100 handsfree kit, you should charge the handsfree kit 's battery; please refer to the section Charging MyCK100 handsfree kit of this guide. Before pairing the MyCK100 handsfree kit with a mobile phone please refer to the section Pairing of MyCK100 Bluetooth handsfree kit of this guide. Box content Please make sure that in addition to this guide you have: - MyCK100 handsfree kit, - 3 clips, - Charger, - Charging Adapter, - A soft bag Interface Charging MyCK100 handsfree kit Upon reception your handsfree kit is not charged. Before first use, you therefore need to recharge it completely during approx. 8 hours using provided charger and charging adapter. Next recharge should last approx. 2h 30 minutes. If you hear 1 beep each minutes in your handsfree kit and light indicator flashes in red each 30 s, handsfree kit needs to be recharged. Please connect the charging adapter on one side to the handsfree kit and on the other side to the power charger, which you can then connect into a mains plug. Light indicator is red during charging process and turns blue after completion. During the charge you can used your handsfree kit. Please note use of any other charger will cancel the handsfree kit warranty. The handsfree kit shall operate as normal during Charging Mode (such as receiving call, accept call etc). To ensure a maximal life time to the battery, it is recommended to recharge the battery only when it gets completely empty. Life cycle should allow approx. 500 charge & discharge cycles If your handsfree kit is left with low battery for a long time, battery may get into overdischarge. In such case, you may need to charge your battery during up to 10 hours before it recovers a full charge Don't leave the charger connected to the headset more than 24 hours. The MyCK100 handsfree kit has a protection in temperature activated during the charge. The charge will be stopped under 0°C and over 55 °C in order to ensure a maximal life time to the battery Button 1 Button 1 (On/Off) Button 2 (Mute) Main push button § Volume cutting wheel Note : Short press is an instantaneous press. Medium-long press is between 2 s and 5s. Long press exceed 5s Microphone cutting wheel Switching ON/OFF the myCK100 handsfree kit The myCK100 handsfree kit will be switched on (from off state) by doing a medium-long press on Button 1. A short low tone beep followed by 1 high low tone beep is played by the handsfree kit. The myCK100 handsfree kit will be switched off (from on state) by doing a medium-long press on Button 1. A short high tone beep followed by 1 short low tone beep is played by the handsfree kit. Pairing of myCK100 Bluetooth handsfree kit Before using the myCK100 handsfree kit, you must pair it with your Bluetooth® mobile phone. Pairing is the process of linking two Bluetooth® devices, so that they can communicate. The pairing procedure only needs to be done once. Afterwards, every time you switch on your handsfree kit (Push medium-long on Button 1), it will automatically connect to your mobile phone. If the user loses the Bluetooth® connection with his mobile (Ex: An user leaves the handsfree kit in his car and takes his mobile phone with him). The user should push once the main push button § to connect the handsfree kit with his Bluetooth® mobile phone. If you pair your Bluetooth® mobile phone with another Bluetooth® device, you will have to pair the handsfree kit with your phone again before use. IMPORTANT: Before pairing, all Bluetooth® devices must be switched off. To initiate the pairing, put both the myCK100 handsfree and the mobile phone within 0.3 meter (1 foot) of each other. Make sure there is no Wi-Fi equipment operating in the vicinity. 1. Switch on the myCK100 handsfree kit (Push medium-long on Button 1). Pairing will be automatically initated by the myCK100 handsfree kit itself when detecting no pairing history list (No mobile phone paired, yet). The handsfree kit will indicate the pairing Mode by alternately blinking blue and red LED indicator in every 1-second interval. If a mobile phone is already listed in the handsfree kit. The handsfree kit enters in pairing Mode after a long press on button 2. The Pairing Mode is indicated by alternately blinking blue and red LED indicator in every 1-second interval. If your Bluetooth® mobile phone is switched off the handsfree kit stays in pairing mode around 3 minutes. 2. Switch on your phone and select the Bluetooth® mode (Service discovery) on the Mobile phone (See the Bluetooth® mobile phone user guide). 3. Once the mobile phone detects the myCK100 handsfree kit, a message is displayed with the following information: myCK100 . 4. Follow the phone instructions to accept the pair…

Text truncated - open the document above for the full version.

Design certification Document Document No: Objective : Describe sagem Bluetooth Car Kit specification as per SAGEM company requirement. Author(s) : Mohd Rosdi Ngah Date : March 14, 2005 Balda-ThongFook Solution Confidential Proprietary Page 13 of 20 8. Block Diagram Sagem Carkit Block Diagram Flash Memory 512K x 16 bits (8 Mbit) CSR BC03 MM EXT. (BC352239A) 16MHz Li Polymer Battery (3.7V) + Protection circuitry SPK LDO 2.7 V MIC Balun+BPF Matching Antenna SPI UART Input voltage 5-15V Button 2 EC Touch PA Power Management a) 5VPA – TPS61027DRC b) 1.8VDC – ISL6273 c) 3.3VDC – LP39851M5 Supply to Power amplifier, flash memory, & CSR chipset, LED, Buttons Button 1 Charging IC, ISL6292DCRZ 5V Regulator ENCODER LED Blue and Red

SAGEM CAR KIT FRONT VIEW:- FRONT VIEW BACK VIEW

: M9H189355073 Fcc warning label details & Location:- 25 mm 10 mm SAGEM CAR KIT BAR CODE LABEL: RATING 5V, 550mA FCC ID: M9H189355073 189355086135 06 25mm 19mm

Design certification Document Document No: Objective : Describe sagem Bluetooth Car Kit specification as per SAGEM company requirement. Author(s) : Mohd Rosdi Ngah Date : March 14, 2005 Balda-ThongFook Solution Confidential Proprietary Page 6 of 20 4. Operational Indication –Key Press Functioning Mapping Table Note 1: Short Press is an instantaneous press where button is quickly pressed and released. Medium-Long Press is a key press that has reached or exceeded 2 seconds but less than 5 seconds interval before it is released. Long Press is a key press that has reached or exceed 5 seconds interval before it is released. Call State Button Idle Incoming Call Outgoing call Active call Waiting call 2nd active call 2nd outgoing call Hold Pairing Off EASY_TOUCH short Voice Dial OR Call Transfer Answer Call Cancel Outgoing Call End Call Answer waiting call, put current call on hold End active call, held call become active call Cancel 2nd outgoing call 2nd voice dial EASY_TOUCH Medium-Long Last Number Dial Reject Call Reject waiting call, current call remains active call 2nd last number redial BUTTON_2 short Mute -> un-mute un-mute - > mute Mute -> un- mute un-mute -> mute Clear Pair History List BUTTON_2 Medium-Long Switch Call OR Hold Switch Call Unhold BUTTON_2 Long Pairing Cancel Pairing BUTTON_1 Medium-Long Power Off Power On BUTTON_1 short Check Battery Status VOL_UP scroll If SCO link connected, increase voice volume If SCO link not connected, increase ring volume VOL_DOWN scroll If SCO link connected, increase voice volume If SCO link not connected, increase ring volume

TEST REPORT Your Ref: 56Q0500944DDate: 05 May 2006 Our Ref: 56S060365/01Page: 1 of 50 DID: +65-6885 1459Fax: +65-6774 1459 NOTE: This report is issued subject to PSB Corporation's "Terms and Conditions Governing Technical Services". The terms and conditions governing the issue of this report are set out as attached within this report. LA-2001-0212-A LA-2001-0213-F LA-2001-0214-E LA-2001-0215-B LA-2001-0216-G LA-2001-0217-G The results reported herein have been performed in accordance with the laboratory’s terms of accreditation under the Singapore Accreditation Council - Singapore Laboratory Accreditation Scheme. Tests marked "Not SAC-SINGLAS Accredited" in this Report are not included in the SAC-SINGLAS Accreditation Schedule for our laboratory. Head Office: PSB Corporation • Testing Group • 1 Science Park Drive Singapore 118221 • Hotline:+65 6885 1333 • Fax:+65 6775 9725 • Email: [email protected] • Website: www.psbcorp.com Reg. No. : 199002667R • Regional Offices: Bangkok • Guangzhou • Jakarta • Kuala Lumpur • Qingdao • Shanghai • Tianjin FORMAL REPORT ON TESTING IN ACCORDANCE WITH FCC Parts 15B & C : 2006 OF A BLUETOOTH HANDS-FREE KIT MyCK100 [ Model : MyCK100 ] [ FCC ID : M9H189355073 ] TEST FACILITY Telecoms & EMC, Testing Group, PSB Corporation Pte Ltd 1 Science Park Drive, Singapore 118221 FCC REG. NO. 90937 (3m & 10m OATS) 99142 (10m Anechoic Chamber) 871638 (5m Anechoic Chamber) 325572 (10m Anechoic Chamber) IND. CANADA REG. NO. IC 4257 (3m and 10m Anechoic Chambers) PREPARED FOR Sagem Communication Safran Group 2, rue du Petit-Albi 95802 Cergy St.Christophe, France Tel : +33 (0) 1 58 11 9070Fax : +33 (0) 1 58 11 1417 JOB NUMBER 56S060365 TEST PERIOD 18 Apr 2006 – 20Apr 2006 PREPARED BYAPPROVED BY ____________________ Quek Keng Huat Associate Engineer ____________________ Lim Cher Hwee Product Manager 56S060365/01 Sagem Communication Safran GroupPage 2 of 50 Bluetooth Hands-Free Kit MyCK100 [ Model : MyCK100 ] [ FCC ID : M9H189355073 ] TABLE OF CONTENTS TEST SUMMARY PRODUCT DESCRIPTION SUPPORTING EQUIPMENT DESCRIPTION EUT OPERATING CONDITIONS CONDUCTED EMISSION TEST RADIATED EMISSION TEST CARRIER FREQUENCY SEPARATION TEST SPECTRUM BANDWIDTH (20dB BANDWIDTH MEASUREMENT) TEST NUMBER OF HOPPING FREQUENCIES TEST AVERAGE FREQUENCY DWELL TIME TEST MAXIMUM PEAK POWER TEST RF CONDUCTED SPURIOUS EMISSIONS TEST BAND EDGE COMPLIANCE (CONDUCTED) TEST BAND EDGE COMPLIANCE (RADIATED) TEST PEAK POWER SPECTRAL DENSITY TEST DUTY CYCLE FACTOR COMPUTATION ANNEX A- EUT PHOTOGRAPHS / DIAGRAMS ANNEX B- FCC LABEL & POSITION ANNEX C- USER MANUAL, TECHNICAL DESCRIPTION, BLOCK & CIRCUIT DIAGRAMS 56S060365/01 Sagem Communication Safran GroupPage 3 of 50 Bluetooth Hands-Free Kit MyCK100 [ Model : MyCK100 ] [ FCC ID : M9H189355073 ] TEST SUMMARY The product was tested in accordance with the customer's specifications. Test Results Summary Test StandardDescriptionPass / Fail FCC Part 15: 2006 15.107(a), 15.207Conducted EmissionsPass 15.109(a), 15.205, 15.209 Radiated Emissions (Spurious Emissions inclusive Restricted Bands Requirement) Pass Carrier Frequency SeparationPass15.247(a)(1) Spectrum Bandwidth (20dB Bandwidth Measurement) Pass Number of Hopping FrequenciesPass15.247(a)(1)(iii) Average Frequency Dwell TimePass 15.247(b)(1)Maximum Peak PowerPass 15.247(d)RF Conducted Spurious EmissionsPass 15.247(d)Band Edge Compliance (Conducted)Pass 15.247(d)Band Edge Compliance (Radiated)Pass 15.247(e)Peak Power Spectral DensityPass 15.35(c)Duty Cycle Factor ComputationRefer to page 49 for details Notes 1.Three channels as listed below, which respectively represent the lower, middle and upper channels of the Equipment Under Test (EUT) were chosen and tested. For each channel, the EUT was configured to operate in the test mode. Transmit Channel Frequency (GHz) Channel 02.402 Channel 392.441 Channel 782.480 2.All the test measurements in section 15.247 were done based on conducted method expect Band Edge Compliance (Radiated) test. 3.The EUT is a Class B device when in non-transmitting state and meets the FCC Part15B Class B requirements. Modifications 1.No modifications were made. 56S060365/01 Sagem Communication Safran GroupPage 4 of 50 Bluetooth Hands-Free Kit MyCK100 [ Model : MyCK100 ] [ FCC ID : M9H189355073 ] PRODUCT DESCRIPTION Description: The Equipment Under Test (EUT) is a Bluetooth Hands-Free Kit MyCK100. Manufacturer: Blada Solutions (Malaysia) Sdn Bhd 3 Jalan Zarib 6, Kawasan Perindustrian Zarib, 31500 Lahat, Ipoh, Perak, Malaysia Model Number: MyCK100 FCC ID: M9H189355073 Serial Number: 0158800012B / 01588000133 Microprocessor: Bluetooth chip CSR BC352239A Operating / Transmitting Frequency : 2.402GHz - 2.480GHz Clock / Oscillator Frequency: 16MHz Modulation: Gaussian Frequency Shift Keying Port / Connectors: Refer to manufacturers' user manual / operating manual. Rated Input Power: AC 90V ~ 265V, 60Hz/60Hz Accessories: Power Adapter Model 1 DA2-3102EUWR Input 100V – 240V, 0.3A 60Hz/50Hz Output 5Vdc, 0.4A Power Adapter Model 2 DA2-3102USWR Input 100V – 240V, 0.3A 60Hz/50Hz Output 5Vdc, 0.4A Power Adapter Model 1 DCH3-05US Input 110V – 230V, 1.2A 60Hz/50Hz Output 5Vdc, 0.5A Car Adapter Model CLA4-3102 Input 12V - 24VDC 0.4A Output 6.5V 0.5A 56S060365/01 Sagem Communication Safran GroupPage 5 of 50 Bluetooth Hands-Free Kit MyCK100 [ Model : MyCK100 ] [ FCC ID : M9H189355073 ] SUPPORTING EQUIPMENT DESCRIPTION Equipment Description (Including Brand Name) Model, Serial & FCC ID NumberCable Description (List Length, Type & Purpose) M/N: Compaq Evo N1020V S/N: 9X35LDLZR20B Compaq Laptop FCC ID: DoC 2.00m unshielded power cable M/N: 239428-001 S/N: Nil Compaq AC/DC Power Adapter (for Compaq Laptop) FCC ID: Nil 2.00m unshielded power cable 56S060365/01 Sagem Communication Safran GroupPage 6 of 50 Bluetooth Hands-Free Kit MyCK100 [ Model : MyCK100 ] [ FCC ID : M9H189355073 ] EUT OPERATING CONDITIONS FCC Part 15 1. Conducted Emissions 2. Radiated Emissions (Spurious Emissions inclusive Restricted Bands Require…

Text truncated - open the document above for the full version.