M9H95E2002PGSM 900/1900 Mobile Phone

1 You have just bought a mobile phone and we congratulate you on your choice. Your phone will allow you to use different international networks (GSM 900 MHz and PCS 1900 MHz) depending on the roaming agreements between the operators. We would like to remind you that this phone is approved to European standards. To get the most out of using your phone, we recommend that you read this manual carefully and keep it handy for future reference if needed. WARNING According to the configuration of the networks and associated subscriptions, certain functions may not be available (usually indicated by *). Make sure your SIM card is compatible with your phone. If an incompatible SIM card is inserted, a message will be displayed when switching on your phone. For further information, contact your Operator. The SAGEM logo and trademark are the property of SAGEM SA. AT is a registered trademark of Hayes Microcomputer products Inc. Hayes is a registered trademark of Hayes Microcomputer Products Inc. T9™ Text Input is a registered trademark of ©Tegic Communications Inc. T9 is licensed under one or more of the following U.S. Patents: 5,818,437, 5,953,541, 5,187,480, 5,945,928, 6,011,554 and additional patents are pending worldwide. Compatibility of your SIM card Your phone is compatible with SIM 3V cards only. MYX-3p_EN-00.p6519/12/2002, 15:221 2 Conformance Document SAGEM SA declare under its sole responsibility that the product Dual Band GSM/PCS Type E2002 conforms to the requirements of the following EEC directives: EEC Directive1999/5/CE SafetyEN 60950: 2000 EMCEN 301 489-1 EN 301 489-7 Low voltage directive73/23/CEE Network3GPP TS 51.010-1 v4.8.0 TBR 19 Edition 5 TBR 20 Edition 3 EN 301511 v7.0.1 HealthEN 50360 EN 50361 FCC Conformance Document FCC Part 24 NetworkNAPRD03.ver 2.6.1 HealthDraft IEEE Std 1528-200x MYX-3p_EN-00.p6519/12/2002, 15:222 3 Use of your phone is subject to safety rules designed to protect the user and his or her environment. Exposure to Radio Frequency Signals •Your wireless handheld portable phone is a low power radio transmitter and receiver. When it is ON, it receives and also sends out frequency (RF) signals. •In August, 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for handheld wireless phones. Those guidelines are consistent with the safety standards previously set by both U.S. and international standards bodies: ANSI C95.1 (1992)* NCPR Report 86 (1986)* ICNIRP (1996)* (*) American National Standards Institute; National Council on Radiation Protection and Measurements; International Commission and Non-Ionizing Radiation Protection. •Those standards were based on comprehensive and periodic evaluations of the relevant scientific literature. For example, over 120 scientists, engineers, and physicians from universities, government health agencies, and industry reviewed the available body of research to develop the ANSI Standard (C95.1). •The design of your phone complies with the FCC guidelines (and those standards). Safety Information for Wireless handled phones MYX-3p_EN-00.p6519/12/2002, 15:223 4 Safety Information for Wireless handled phones •For body worn operation, this phone has been tested and meets FCC RF exposure guidelines when used with an accessory that contains no metal and that positions the handset a minimum of 1.5 cm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Phone Operation •Normal position: hold the phone as you would any other phone with the upper zone (back of the LCD display) pointed up and over your shoulder. •Tips on efficient operation: for your phone to operate most efficiently: do not touch cover unnecessarily the top part of the phone with your hand. This would cover the integrated antenna and affect call quality and may cause the phone to operate at a higher power level than otherwise needed. Driving •Check the laws and regulations on the use of wireless telephones in the areas where you drive. Always obey them. Also, if using your phone while driving while driving please: - Give full attention of driving, driving safely is your first responsibility - Use hands-free operation, if available - Pull off the road and park before making or answering a call if driving conditions so require. MYX-3p_EN-00.p6519/12/2002, 15:224 5 Safety Information for Wireless handled phones Electronic Devices •Most modern electronic equipment is shielded from RF signals. However, certain electronic equipment may not be shielded against the RF signals from your wireless phone. •Some phone accessories allow to reduce the radiation interferences of the phone. Please contact your distributor. Pacemakers The Health Industry Manufacturers Association recommends that a minimum separation of six (6”) inches be maintained between a handheld wireless phone and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of Wireless Technology Research. Persons with pacemakers: •Should ALWAYS keep the phone more than six inches from their pacemaker when the phone is turned ON •Should not carry the phone in the breast pocket •Should use the ear opposite to the pacemaker to minimize the potential for interference •If you have any reason to suspect that interference is taking place, turn your phone OFF immediately. MYX-3p_EN-00.p6519/12/2002, 15:225 6 Safety Information for Wireless handled phones Hearing Aids Some digital wireless phones may interfere with some hearing aids. In the event of such interference, you may want to consult your service provider. Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if they are adequately shielded from external RF energy. Your physician may be able to assist you in obtaining this information. Turn your phone OFF in health care facilities when any regulations posted in these a…

Text truncated - open the document above for the full version.

s e Centre de Saint Christophe - DTM TELEPHONIE MOBILE MOBILE PHONES Ref : SCT TMO MY3 NB PROJ 32–Ind A Date : 31/10/02 Document E Reproduction et divulgation interdites 10/22 2.1.2 External Photos s e Centre de Saint Christophe - DTM TELEPHONIE MOBILE MOBILE PHONES Ref : SCT TMO MY3 NB PROJ 32–Ind A Date : 31/10/02 Document E Reproduction et divulgation interdites 11/22 2.1.3 Without Housing

s e Centre de Saint Christophe - DTM TELEPHONIE MOBILE MOBILE PHONES Ref : SCT TMO MY3 NB PROJ 32–Ind A Date : 31/10/02 Document E Reproduction et divulgation interdites 2.1.5 Label Informations s e Centre de Saint Christophe - DTM TELEPHONIE MOBILE MOBILE PHONES Ref : SCT TMO MY3 NB PROJ 32–Ind A Date : 31/10/02 Document E Reproduction et divulgation interdites Label Location

s e Centre de Saint Christophe - DTM TELEPHONIE MOBILE MOBILE PHONES Ref : SCT TMO MY3 NB PROJ 32–Ind A Date : 31/10/02 Document E Reproduction et divulgation interdites 12/22 2.1.4 Internal Photos

CETECOM ICT Services GmbH Untertuerkheimer Str. 6-10, 66117 Saarbruecken, GermanyPhone: +49 (0) 681 598-0Fax: -8475 SAR-Laboratory Phone: +49 (0) 681 598-8454 . As of 2002.12.18 Page 1 of 38 Accredited testing laboratory DAR registration number: TTI-P-G 166/98 Federal Motor Transport Authority (KBA) DAR registration number: KBA-P 00070-97 Test report no. : 2-3078/02_1_3 Type identification : E 2002P Test specification : Draft IEEE Std 1528-200X : OET Bulletin 65 FCC-ID: M9H95E2002P Test specification : CETECOM ICT Services GmbH Test report no.: 2-3078/02_1_3 As of 2002.12.18 Page 2 of 38 Table of Contents 1General Information............................................................................................................................................................... 3 1.1Notes .............................................................................................................................................................................. 3 1.1.1Statement of Compliance ....................................................................................................................................... 3 1.2Testing laboratory .......................................................................................................................................................... 4 1.3Details of applicant ........................................................................................................................................................ 4 1.4Application details ......................................................................................................................................................... 4 1.5Test item ........................................................................................................................................................................ 5 1.5.1Test specification(s) ............................................................................................................................................... 6 1.6RF exposure limits ......................................................................................................................................................... 6 2Technical test ......................................................................................................................................................................... 7 2.1Summary of test results.................................................................................................................................................. 7 2.2Test environment ........................................................................................................................................................... 7 2.3Measurement and test set-up.......................................................................................................................................... 7 2.4Measurement system...................................................................................................................................................... 8 2.4.1System Description ................................................................................................................................................ 8 2.4.2Test environment ................................................................................................................................................... 9 2.4.3Probe description ................................................................................................................................................... 9 2.4.4Phantom description............................................................................................................................................. 10 2.4.5Device holder description .................................................................................................................................... 10 2.4.6Scanning procedure.............................................................................................................................................. 11 2.4.7Spatial Peak SAR Evaluation............................................................................................................................... 12 2.4.8Data Storage and Evaluation................................................................................................................................ 13 2.4.9Test equipment utilized ........................................................................................................................................ 15 2.4.10Tissue simulating liquids : dielectric properties................................................................................................... 16 2.4.11Tissue simulating liquids : parameters ................................................................................................................. 17 2.4.12Measurement uncertainties .................................................................................................................................. 18 2.4.13System validation................................................................................................................................................. 19 2.4.14Validation procedure............................................................................................................................................ 20 2.5Test results (Head and Body SAR) .............................................................................................................................. 21 2.6Test results (conducted power measurement) .............................................................................................................. 21 Annex 1System performance verification ............................................................................................................................. 22 Annex 2Measurement results (printout from DASY TM )....…

Text truncated - open the document above for the full version.

CETECOM ICT Services GmbH Untertuerkheimer Str. 6-10, 66117 Saarbruecken, GermanyPhone: +49 (0) 681 598-0Fax: -8475 SAR-Laboratory Phone: +49 (0) 681 598-8454 . As of September 20, 2002Page 1 of 30 Accredited testing laboratory DAR registration number: TTI-P-G 166/98 Federal Motor Transport Authority (KBA) DAR registration number: KBA-P 00070-97 Appendix to the Report 2-3078-1-3/02 Photo documentation Test specification : CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 2 of 30 Annex 3 Photo documentation Picture no. 1 Measurement System DASY 3 CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 3 of 30 Picture no. 2 E2002p front touch left CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 4 of 30 Picture no. 3 E2002p rear touch left CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 5 of 30 Picture no. 4 E2002p side touch left CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 6 of 30 Picture no. 5 E2002p front tilted left CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 7 of 30 Picture no. 6 E2002p side tilted left CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 8 of 30 Picture no. 7 E2002p front tilted left CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 9 of 30 Picture no. 8 E2002p front touch right CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 10 of 30 Picture no. 9 E2002p side touch right CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 11 of 30 Picture no. 10 E2002p rear touch right CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 12 of 30 Picture no. 11 E2002p front tilted right CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 13 of 30 Picture no. 12 E2002p side tilted right CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 14 of 30 Picture no. 13 E2002p rear tilted right CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 15 of 30 Picture no. 14 E2002p flat front 15mm 15 mm CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 16 of 30 Picture no. 15 E2002p flat front 15mm CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 17 of 30 Picture no. 16 E2002p flat front 15mm CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 18 of 30 Picture no. 17 E2002p flat rear 15mm CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 19 of 30 Picture no. 18 E2002p flat rear 15mm 15 mm CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 20 of 30 Picture no. 19 E2002p flat rear 15mm CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 21 of 30 Picture no. 20 E2002p front CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 22 of 30 Picture no. 21 E2002p left side CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 23 of 30 Picture no. 22 E2002p rear side with battery CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 24 of 30 Picture no. 23 E2002p rear side without battery CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 25 of 30 Picture no. 24 E2002p rear side CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 26 of 30 Picture no. 25 E2002p left side CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 27 of 30 Picture no. 26 battery front CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 28 of 30 Picture no. 27 battery rear CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 29 of 30 Picture no. 28 liquid depth head 1900 MHz CETECOM ICT Services GmbH Photo documentation Report No.: 2-3078-1-3/02 As of September 20, 2002Page 30 of 30 Picture no. 29 liquid depth body 1900 MHz

CETECOM ICT Services GmbH Untertuerkheimer Str. 6-10, 66117 Saarbruecken, GermanyPhone: +49 (0) 681 598-0Fax: -8475 SAR-Laboratory Phone: +49 (0) 681 598-8454 . As of December 20, 2002Page 1 of 31 Accredited testing laboratory DAR registration number: TTI-P-G 166/98 Federal Motor Transport Authority (KBA) DAR registration number: KBA-P 00070-97 Appendix to the Report 2-3078-1-3/02 Calibration Data, Phantom Certificate and detail Information of the DASY 3 System Test specification : CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 2 of 31 Table of Content 1Calibration report “Probe ET3DV6”...............................................................................................................................3 2Calibration report “1900 MHz System validation dipole”..............................................................................................13 3Certificate of Conformity “SAM Twin Phantom V4.0/V4.0C”......................................................................................24 4Application Note Validation and system Check.............................................................................................................26 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 3 of 31 1 Calibration report “Probe ET3DV6” CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 4 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 5 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 6 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 7 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 8 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 9 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 10 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 11 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 12 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 13 of 31 2 Calibration report “1900 MHz System validation dipole” CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 14 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 15 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 16 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 17 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 18 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 19 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 20 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 21 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 22 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 23 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 24 of 31 3 Certificate of Conformity “SAM Twin Phantom V4.0/V4.0C” CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 25 of 31 CETECOM ICT Services GmbH Calibration Data and Phantom Information; Report No.: 2-3078-1-3/02 As of December 20, 2002Page 26 of 31 4 Application Note Validation and system Check 4.1.1.1 Purpose of validation The Validation and system check verify that the system operates within ist specifications. System and operator errors can be detected and corrected. It is recommended that the validation be performed prior to any usage of the system in order to guarantee reproducible results. The measurement of the Specific Absorption Rate (SAR) is a complicated task and the resultdepends on the proper functioning of many components and the correct settings of manyparameters. Faulty results due to drift, failures or incorrect parameters might not berecognized, since they often look similar in distribution to the correct ones. The DosimetricAssessment System DASY3 incorporates a validation procedure to test the properfunctioning of the system. The system validation uses normal SAR measurements in asimplified setup (the flat phantom section of the Generic Twin Phantom) with a wellcharacterized source (a matched dipole of a specified distance). This setup was selected to give a high sensitivity to all parameters that might fail or vary over time (e.g. probe, liquid parameters, and software settings) and a low sensitivity to external effects inherent in the system (e.g. positioning uncertainty of the device holder). The validation does not replace the calibration of the components. The accuracy of the validation is not sufficient for calibration purposes. It is possible to calculate…

Text truncated - open the document above for the full version.

CETECOM ICT Services GmbH Radio Satellite Communication Untertürkheimer Straße 6-10 . D-66117 SaarbrückenTelefon: +49 (0)681 598-9100Telefax: -9075 RSC11issue test report consist of 91 PagesPage 1 (91) BLUETOOTH TM is a trademark owned by Bluetooth SIG, Inc. and licensed to CETECOM TTI-P-G-166/98-30 Accredited Bluetooth Test Facility (BQTF) Test report no.: 2_3078-01-04/02 FCC Part 24 E2002P FCC ID: M9H95E2002P CETECOM – ICT Services GmbH Untertürkheimerstr. 6-10 66117 Saarbrücken, Germany Telephone: + 49 (0) 681 / 598-0 Fax: + 49 (0) 681 / 9075 CETECOM ICT Services GmbH Test report no..: 2_3078-01-04/02Issue Date: 2002-11-13Page 2 (91) Table of Contents 1 General information 1.1 Notes 1.2 Testing laboratory 1.3 Details of applicant 1.4 Application details 1.5 Test item 1.6 Test standards 2 Technical test 2.1 Summary of test results 2.2 Test report 1 General information 1.1 Notes The test results of this test report relate exclusively to the test item specified in 1.5. The CETECOM ICT Services GmbH does not assume responsibility for any conclusions and generalisations drawn from the test results with regard to other specimens or samples of the type of the equipment represented by the test item. The test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of the CETECOM ICT Services GmbH. 1.2Testing laboratory CETECOM ICT Services GmbH Untertürkheimer Straße 6 - 10 66117 Saarbrücken Germany Telefone: + 49 681 598 - 9100 Telefax : + 49 681 598 - 9075 E-mail: [email protected] Internet: www.cetecom-ict.de Accredited testing laboratory DAR-registration number : TTI-P-G-166/98-30 Accredited Bluetooth TM Test Facility (BQTF) BLUETOOTH TM is a trademark owned by Bluetooth SIG, Inc. and licensed to CETECOM CETECOM ICT Services GmbH Test report no..: 2_3078-01-04/02Issue Date: 2002-11-13Page 3 (91) 1.3Details of applicant Name : SAGEM SA Street : 4, rue du Petit Albi; B.P. 8448 City : F-95801 Cergy Pontoise Cedex Country : France Telephone : +33-1-3073-7277 Telefax : +33 1 30 38 65 55 Contact : Mr. Bruno Perdigues Telephone : +33 1 30 73 37 14 e-mail: [email protected] 1.4Application details Date of receipt of application : 2002-11-04 Date of receipt of test item : 2002-11-11 Date of test : 2002-11-12/13 1.5Test item Type of equipment : Dual Band GSM Mobile Phone (PCS 900/1900 MHz) Type designation:E2002P (Marketing Name : myX-3p) Manufacturer:Applicant Street: City: Country: Serial number:IMEI : 351.357.95.000002.0 Additional informations: : Frequency:1850 – 1910 MHz Type of modulation:300KGXW Number of channels :300 (PCS1900) Antenna:Integral antenna Power supply:3,6V DC Li-Polymer Output power GSM 1900 :cond : 29.6 dBm Peak , ERP: 25.67 dBm (Burst); EIRP: 27.77 dBm (Burst) Type of equipment:Temperature range : -30°C - +60°C FCC – ID:M9H95E2002P FCC registration number :0006-7315-09 Hardware:V53xx Software:J 3,8 1.6Test standards: FCC Part 24 FCC Part 15 CETECOM ICT Services GmbH Test report no..: 2_3078-01-04/02Issue Date: 2002-11-13Page 4 (91) 2 Technical test For Part 24/22 we use the substitution method ( TIA/EIA 603). 2.1Summary of test results No deviations from the technical specification(s) were ascertained in the course of the tests performed. FINAL VERDICT: PASS Technical responsibility for area of testing : 2002-11-13RSC 8411 Berg M. DateSectionNameSignature Technical responsibility for area of testing : 2002-11-13RSC8412Hausknecht D. DateSectionNameSignature CETECOM ICT Services GmbH Test report no..: 2_3078-01-04/02Issue Date: 2002-11-13Page 5 (91) 2.2Testreport TEST REPORT Test report no. : 2_3078-01-04/02 CETECOM ICT Services GmbH Test report no..: 2_3078-01-04/02Issue Date: 2002-11-13Page 6 (91) TEST REPORT REFERENCE LIST OF MEASUREMENTS PARAMETER TO BE MEASURED PAGE Part PCS 1900 POWER OUTPUT SUBCLAUSE § 24.2327 FREQUENCY STABILITY SUBCLAUSE § 24.2359 EMISSIONS LIMITS §24.23812 CONDUCTED SPURIOUS EMISSIONS26 OCCUPIED BANDWIDTH §2.98935 ADDITIONEL MEASUREMENTS FOR THE ANCILLARY EQUIPMENT PART 15.109 44 TEST EQUIPMENT AND ANCILLARIES USED FOR TESTS72 Test site74 Photographs of the equipment80 CETECOM ICT Services GmbH Test report no..: 2_3078-01-04/02Issue Date: 2002-11-13Page 7 (91) REFERENCE NUMBER(S) OF TEST EQUIPMENT USED (for reference numbers see test equipment listing) 64 POWER OUTPUT SUBCLAUSE § 24.232 Summery: This paragraph contains both average , peak output powers and EIRP measurements for the mobile station. In all cases, the peak output power is within the required mask (this mask is specified in the JTC standards, TIA PN3389 Vol. 1 Chap 7, and is no FCC requirement). Method of Measurements: The mobile was set up for the max. output power with pseudo random data modulation. The power was measured with R&S Signal Analyzer FSIQ 26 ( peak and average) This measurements were done at 3 frequencies, 1850,2 MHz, 1880,0 MHz and 1909,8 MHz (bottom, middle and top of operational frequency range) Limits: Power StepNominal Peak Output Power (dBm) Tolerance (dB) 0+30 ± ±± ± 2 Power Measurements: Conducted: Frequency (MHz) Power Step Peak Output Power (dBm) Average Output Power (dBm) 1850.2029.629.5 1880.0029.329.2 1909.8029.329.2 Measurement uncertainty ± ±± ±0.5 dB CETECOM ICT Services GmbH Test report no..: 2_3078-01-04/02Issue Date: 2002-11-13Page 8 (91) REFERENCE NUMBER(S) OF TEST EQUIPMENT USED (for reference numbers see test equipment listing) 17 - 24 EIRP Measurements Description: This is the test for the maximum radiated power from the phone. Rule Part 24.232(b) specifies that "Mobile/portable stations are limited to 2 watts e.i.r.p. peak power..." and 24.232(c) specifies that "Peak transmit power must be measured over any interval of continuous transmission using instrumentation calibrated in terms of an rms-equivalent voltage." Method of Measurement: 1. In an anechoic antenna test chamber, a half-wave dipole antenna for the frequency band of interest is placed …

Text truncated - open the document above for the full version.

CETECOM ICT Services GmbH Test report no..: 2_3078-01-04/02Issue Date: 2002-11-13Page 74 (91) Test site CETECOM ICT Services GmbH Test report no..: 2_3078-01-04/02Issue Date: 2002-11-13Page 75 (91) Test site CETECOM ICT Services GmbH Test report no..: 2_3078-01-04/02Issue Date: 2002-11-13Page …

Text truncated - open the document above for the full version.