MAU011Tablet Computer with 2.4 GHz 802.11 TX

CA-27 Operation Manual Part Number: 7990 0121 0001 R00 (May 2004) i TRADEMARKS All brand and product names are trademarks or registered trademarks of their respective companies. NOTE Information in this manual is subject to change without notice. ii Regulatory Information This appendix provides regulatory statements and safety notices on your computer. NOTE: Marking labels located on the exterior of your computer indicate the regulations that your model complies with. Please check the marking labels and refer to the corresponding statements in this appendix. Some notices apply to specific models only. iii On the Use of the System Class B Regulations USA Federal Communications Commission Radio Frequency Interference Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. Please note: The use of a non-shielded interface cable with this equipment is prohibited. iv Canada Canadian Department of Communications Radio Interference Regulations Class B Compliance Notice This Class B digital apparatus meets all requirements of the Canada Interference-Causing equipment regulations. Cet appareil numérique de Classe B respecte toutes les exigences du Règlement Canadien sur le matériel brouileur. This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada. Safety Notices About the Battery Caution Texts Concerning Lithium Batteries DANISH ADVARSEL! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandøren. NORWEGIAN ADVARSEL: Eksplosjonsfare ved feilaktig skifte av batteri. Benytt samme batteritype eller en tilsvarende type anbefalt av apparatfabrikanten. Brukte batterier kasseres i henhold til fabrikantens instruksjoner. SWEDISH VARNING: Explosionsfara vid felaktigt batteribyte. Använd samma batterityp eller en ekvivalent typ som rekommenderas av apparattillverkaren. Kassera använt batteri enligt fabrikantens instruktion. v FINNISH VAROITUS: Paristo voi räjähtää, jos se on virheellisesti asennettu. Vaihda paristo ainoastaan valmistajan suosittelemaan tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden mukaisesti. ENGLISH CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer's instructions. DEUTSCH VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. FRENCH ATTENTION: II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du même type ou d’un type équivalent recommandé par le constructeur. Mettre au rebut les batteries usagées conformément aux instructions du fabricant. Attention (for USA Users) The product that you have purchased contains a rechargeable battery. The battery is recyclable. At the end of its useful life, under various state and local laws, it may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste officials for details in your area for recycling options or proper disposal. About the AC Adapter Use only the AC adapter supplied with your computer. Use of another type of AC adapter will result in malfunction and/or danger. Do not use the adapter in a high moisture environment. Never touch the adapter when your hands or feet are wet. Allow adequate ventilation around the adapter when using it to operate the device or charge the battery. Do not cover the AC adapter with paper or other objects that will reduce cooling. Do not use the AC adapter while it is inside a carrying case. Connect the adapter to a proper power source. The voltage requirements are found on the product case and/or packaging. Do not use the adapter if the cord becomes damaged. vi Do not attempt to service the unit. There are no serviceable parts inside. Replace the unit if it is damaged or exposed to excess moisture. vii About the Modem Caution 1. Never install telephone wiring during a lightning storm. 2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 3. Never touch non-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 4. Use caution when installing…

Text truncated - open the document above for the full version.

Mitac Technology Corp. 1st, R&D Road 2 , Hsinchu Science-Based Industrial Park, Hsinchu, Taiwan, R.O.C. TEL : 886-3-5782280 FAX : 886-3-5778270 Letter Of Agency Date: Jun. 1, 2004 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Applications FCC ID: MAU011 Model: CA27 To Whom It May Concern: Please be advised that Mitac Technology Corporation authorizes International Standards Laboratory (ISL) to act on our behalf, until otherwise notified, for applications submitted to American Telecommunications Certification Body, Inc. (ATCB). We certify that we are not subject to denial of federal benefits that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse ACT of 1988, U.S.C. 862. Further, no party as defined in 47 CFR 1.2002(b), for this application is subject to denial of federal benefits that includes FCC benefits. Thank you for your attention to this matter. _______________________ Eric Pang / Engineer Mitac Technology Corp.

No. 65, Ku Dai Keng St., Hsichih, Taipei 221, R.O. C. Tel: 886-2-2646-2550 FAX: 886-2-26464641 No. 120, Lane 180, San Ho Tsuen, Hsin Ho Rd. Lung-Tan Hsiang, Tao Yuan County 325, Taiwan, R.O.C. Tel: 886-3-407-1718 FAX:886-3-407-1738 Rev 2 C:\tmp\04LR022 Ca27\FCC\AP FORM.doc 02/08/02 Date: Jun. 2, 2004 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Application FCC ID: MAU011 Model: CA27 We would like to apply for FCC Certification on the subject model (EUT). The EUT is a Tablet Personal Computer. We have uploaded the related document for the EUT onto your website. Please review the information we submitted and issue us a grant for the subject model. If you have any comments, please do not hesitate to contact us. Thank you for your attention to these matters. Sincerely, ________________ Eddy Hsiung / Director International Standards Laoboratory No. 65, Ku Dai Keng St., Hsichih, Taipei 221, R.O. C. Tel: 886-2-2646-2550 FAX: 886-2-26464641 No. 120, Lane 180, San Ho Tsuen, Hsin Ho Rd. Lung-Tan Hsiang, Tao Yuan County 325, Taiwan, R.O.C. Tel: 886-3-407-1718 FAX:886-3-407-1738 Rev 2 C:\tmp\04LR022 Ca27\FCC\AP FORM.doc 02/08/02 FCC Labeling Requirements and Information Date: Jun. 2, 2004 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Application FCC ID: MAU011 Model: CA27 The following label information is required by the FCC Rules and Regulations for certified devices. Please find marketing information required by the FCC Rules and Regulations as following: Label Requirements An intentional radiator device subject to certification by the FCC shall carry a warning label which includes the following statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The sample label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time of purchase. Sincerely, ________________ Eddy Hsiung / Director International Standards Laoboratory received, including interference that may cause un- Operation is subject to the following two conditions: and (2) this device must accept any interference This device complies with part 15 of the FCC rules. (1) this device may not cause harmful interference, desired operation. DC INPUT: 19V 4.74A MODEL :CA27 US I.T.E. 10KJ E180413 C LISTED R MTC CLT. Made in Taiwan A004848 S&E FCC ID : MAU011 No. 65, Ku Dai Keng St., Hsichih, Taipei 221, R.O. C. Tel: 886-2-2646-2550 FAX: 886-2-26464641 No. 120, Lane 180, San Ho Tsuen, Hsin Ho Rd. Lung-Tan Hsiang, Tao Yuan County 325, Taiwan, R.O.C. Tel: 886-3-407-1718 FAX:886-3-407-1738 Rev 2 C:\tmp\04LR022 Ca27\FCC\AP FORM.doc 02/08/02 Request for Confidentiality Date: Jun. 2, 2004 American Telecommunications Certification Body, Inc. 6731 Whittier Avenue Suite C110 McLean, VA 22101 RE: Certification Application FCC ID: MAU011 Model: CA27 Please be advised that the following information is to be held confidential on behalf of MITAC TECHNOLOGY CORP. q Block Diagram q Schematics q Technical Spec The application contains technical information which BEHAVIOR TECH COMPUTER CORPORATION deems to be trade secrets and proprietary. If made public, the information might be used to the disadvantage of the applicant in the market place. Thank you for your attention to this matter. Sincerely, ________________ Eddy Hsiung / Director International Standards Laoboratory

American Telecommunications Certification Body Inc. 6731 Whittier Ave, McLean, VA 22101 June 16, 2004 RE: Mitac Technology Corp. FCC ID: MAU011 After a review of the submitted information, I have a few comments on the above referenced Application. Administrative Issues: 1) Please provide a block diagram for the TX portion of the circuitry as required by CFR 2.1033(a)(5). 2) The authorization appears to be for Mitac, but states Wistron. Please explain or correct as necessary. 3) The operational Description mentions an GPRS/GSM/GPS option. Note that depending on how the approval is done for this addition or new model, this may require a Permissive Change application or a new FCC ID number. It is assumed that this application is not including this option and is currently being approved without co-location. Please comment. 4) The schematics do not include the RF mini-PCI card. Note that a schematic for the TX portion of the device is required as specified 2.1033(b)(5) for the RF section. Please provide either a schematic for the mini-PCI card or as an alternative, you may provide a parts list that lists that shows that this part is provided by another manufacturer. Please provide either a schematic or parts list as specified. If necessary, please update the confidentiality letter to include the parts list. 5) Is the frequency 2473 correct in the table in section 6.3 of the EMC report. Note that 2473 is not outside the band but is still inband (2400-2483.5 MHz). 6) The device is a computer and from the labeling appears that the device is also considered a class B PC peripheral subject to a DoC. Please confirm that the DoC testing has been done separately using a appropriately fully configured system according to ANSI C63.4. 7) SAR data has been provided, but the users manual page 10 (labeled as viii, page 147 (labeled as B-6), page 148 (labeled as B-7) all mention a required 20 cm distance. This information is inconsistent with expectations since SAR was provided. Please adjust to clarify or correct as necessary. Note that the prohibition against co-location should remain. Timothy R. Johnson Examining Engineer mailto: [email protected] The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information may result in application termination. Correspondence should be considered part of the permanent submission and may be viewed from the Internet after a Grant of Equipment Authorization is issued. Please do not respond to this correspondence using the email reply button. In order for your response to be processed expeditiously, you must submit your documents through the AmericanTCB.com website. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the sender.

Dear Tim, Here are our answers: 1. A WLAN block diagram was uploaded. file name: WM3B2100 Block &Schematics 2. An authorization letter has been updated. 3. I have updated the technical specification, also a WLAN specification has been uploaded 4. A WLAN schematics was uploaded. file name: WM3B2100 Block &Schematics 5. Yes, 2473MHz is the in-band spurious, not outside-band spurious. We have a little confuse on bandedge test. 15.247 says that ?In any 100KHz bandwidth outside the frequency band in which the spread spectrum intentional radiator is operating, the radio frequency power that shall be at least 20dB below that in the 100KHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement.?We have two problems: Q1: Should the bandedge test contain the in-band spurious test and outside-band spurious test, or just outside-band spurious test? Q2: Should the bandedge test contain the conducted bandedge test and radiated bandedge test, or just conducted bandedge test? 6. We have tested part 15B DOC seperately. I can provide the test report if needed. 7. An updated manual was uploaded. Please review the information we supplied. Thanks for your help. Daphne Liu 06/15/2004

Dear Tim, Here are our answer for item 5. We have test the average and peak value of restricted band again; the frequency range is 2310~2390MHz, 2483.5~2500MHz. Please see the update report on page27~29. (See attached file: 04lr022FC-update.doc) Please review the information we supplied. Thanks for your help. Daphne Liu 06/18/2004

Daphne, Regarding the SAR report: 1) The SAR report is missing the SAR plots for the test data including Z-axis scans for the worse case data. Please provide. Several aspects of the SAR report can not be proofed without this information. These plots should typically contain crest factors, probe factors, liquid parameters, test information, and other important information. 2) The report should include the composition, ingredients, and amounts for tissue liquid listed. 3) better descriptions of extrapolation & interpolation procedures used by the software. Thank You, Timothy R. Johnson NARTE Certified EMC Engineer No. EMC-002205-NE

Dear Tim, Here are our answers: 1) The SAR report is missing the SAR plots for the test data including Z-axis scans for the worse case data. Please provide. Several aspects of the SAR report can not be proofed without this information. These plots should typically contain crest factors, probe factors, liquid parameters, test information, and other important information. Ans: The SAR plot already including Z-axis plot(please see the SAR report Page 28). 2) The report should include the composition, ingredients, and amounts for tissue liquid listed. Ans:Please attachment the SAR Test Report page 14. 3) better descriptions of extrapolation & interpolation procedures used by the software. Ans:Please attachment the SAR Test Report page 16. Please review the information we supplied. Thanks for your help. Daphne Liu 06/23/2004

International Standards Laboratory Report Number: ISL-04LR022P HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178 LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997 Appendix Photographs of EUT of Tablet Personal Computer Model CA27 International Standards Laboratory Report Number: ISL-04LR022P HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178 LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997 -1- EUT-1 International Standards Laboratory Report Number: ISL-04LR022P HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178 LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997 -2- EUT-2

received, including interference that may cause un- Operation is subject to the following two conditions: and (2) this device must accept any interference This device complies with part 15 of the FCC rules. (1) this device may not cause harmful interference, desired operation. DC INPUT: 19V 4.74A MODEL :CA27 US I.T.E. 10KJ E180413 C LISTED R MTC CLT. Made in Taiwan A004848 S&E FCC ID : MAU011 Label & Location Rating Label

International Standards Laboratory Report Number: ISL-04LR022P HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178 LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997 -2- EUT-2 International Standards Laboratory Report Number: ISL-04LR022P HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178 LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997 -3- EUT-3 International Standards Laboratory Report Number: ISL-04LR022P HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178 LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997 -4- EUT-4 International Standards Laboratory Report Number: ISL-04LR022P HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178 LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997 -5- EUT-5 International Standards Laboratory Report Number: ISL-04LR022P HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178 LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997 -6- EUT-6 International Standards Laboratory Report Number: ISL-04LR022P HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178 LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997 -7- EUT-7 International Standards Laboratory Report Number: ISL-04LR022P HC LAB:NVLAP:200234-0;VCCI: R-341,C-354;NEMKO:ELA 113a,113c;BSMI:SL2-IN-E-0037;SL2-R1-E-0037;CNLA:1178 LT LAB:NVLAP:200234-0;VCCI: R-1435,C-1440;NEMKO:ELA 113b,113d;BSMI:SL2-IN-E-0013;CNLA:0997 -8- EUT-8

Compliance Certification Services Inc. Report No: 40601002-SF FCC ID: MAU011 Date of Issue: June 4, 2004 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page1 of 24 ANSI/IEEE Std. C95.1-1992 in accordance with the requirements of FCC Report and Order: ET Docket 93-62, and OET Bulletin 65 Supplement C FCC TEST REPORT For MITAC TECHNOLOGY CORP Tablet PC Trade Name: MITAC Model: CA27 Prepared for MITAC TECHNOLOGY CORP 4F., No.1, R&D Road 2, Hsinchu Science-Based industrial Park, Hsinchu, Taiwan, R.O.C. Prepared by Compliance Certification Services Inc. No. 81-1, Lane 210, Bade Rd. 2, Luchu Hsiang, Taoyuan Hsien, (338) Taiwan, R.O.C. TEL: 886-3-324-0332 FAX: 886-3-324-5235 Compliance Certification Services Inc. Report No: 40601002-SF Date of Issue: June 4, 2004 Page 2 CERTIFICATE OF COMPLIANCE (SAR EVALUATION) Date of Test: June 02, 2004 Applicant: MITAC TECHNOLOGY CORP 4F., No.1, R&D Road 2, Hsinchu Science-Based industrial Park, Hsinchu, Taiwan, R.O.C. Model Number / Trade Name: CA27/ MITAC Device Category: PORTABLE DEVICES Exposure Category: GENERAL POPULATION/UNCONTROLLED EXPOSURE Test Sample is a: Production unit Modulation type: 802.11b Direct Sequence Spread Spectrum Tx Frequency: 2412 ~ 2462 MHz Max. O/P Power: (Conducted/Peak) 16.8dBm Max. SAR (1g): 0.246 W/kg Application Type: Certification FCC Rule Part(s): 15C Note: This Report is only applicable for 802.11b. This wireless portable device has been shown to be capable of compliance for localized specific absorption rate (SAR) for uncontrolled environment/general population exposure limits specified in ANSI/IEEE Std. C95.1- 1992 and had been tested in accordance with the measurement procedures specified in FCC OET 65 Supplement C (released on 6/29/2001 see Test Report). I attest to the accuracy of data. All measurements reported herein were performed by me or were made under my supervision and are correct to the best of my knowledge and belief. I assume full responsibility for the completeness of these measurements and vouch for the qualifications of all persons taking them. Approved by: Reviewed by: Harris W. Lai James Lee Executive Vice President Section Manager Compliance Certification Services Inc. Compliance Certification Services Inc. Compliance Certification Services Inc. Report No: 40601002-SF Date of Issue: June 4, 2004 Page 3 TABLE OF CONTENTS 1. EUT DESCRIPTION ..................................................................................................... 4 2. REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC .... 5 3. DOSIMETRIC ASSESSMENT SYSTEM ................................................................... 5 3.1 MEASUREMENT SYSTEM DIAGRAM ............................................................. 6 3.2 SYSTEM COMPONENTS..................................................................................... 7 4. EVALUATION PROCEDURES .................................................................................. 9 5. MEASUREMENT UNCERTAINTY ......................................................................... 13 6. EXPOSURE LIMIT ..................................................................................................... 14 7. TYPICAL COMPOSITION OF INGREDIENTS FOR LIQUID TISSUE PHANTOMS............ 14 8. MEASUREMENT RESULTS ..................................................................................... 15 8.1 SYSTEM PERFORMANCE CHECK.................................................................. 15 8.2 TEST LIQUID CONFIRMATION ...................................................................... 16 8.3 EUT TUNE-UP PROCEDURES.......................................................................... 17 8.4 SAR MEASUREMENTS RESULTS................................................................... 18 9. EUT PHOTOS .............................................................................................................. 20 10. EQUIPMENT LIST & CALIBRATION STATUS................................................... 22 11. FACILITIES ................................................................................................................. 23 12. REFERENCES ............................................................................................................. 23 13. ATTACHMENTS......................................................................................................... 24 Compliance Certification Services Inc. Report No: 40601002-SF Date of Issue: June 4, 2004 Page 4 1. EUT DESCRIPTION Applicant: MITAC TECHNOLOGY CORP 4F., No.1, R&D Road 2, Hsinchu Science-Based industrial Park, Hsinchu, Taiwan, R.O.C. Model Number / Trade Name: CA27/ MITAC Device Category: PORTABLE DEVICES Exposure Category: GENERAL POPULATION/UNCONTROLLED EXPOSURE Test Sample is a: Production unit Modulation type: 802.11b Direct Sequence Spread Spectrum Tx Frequency: 2412 ~ 2462 MHz Max. O/P Power: (Conducted/Peak) 16.8dBm Max. SAR (1g): 0.246 W/kg Application Type: Certification FCC Rule Part(s): 15C Antennas: PIFA Ant. Compliance Certification Services Inc. Report No: 40601002-SF Date of Issue: June 4, 2004 Page 5 2. REQUIREMENTS FOR COMPLIANCE TESTING DEFINED BY THE FCC The US Federal Communications Commission has released the report and order “Guidelines for Evaluating the Environmental Effects of RF Radiation", ET Docket No. 93-62 in August 1996 [1]. The order requires routine SAR evaluation prior to equipment authorization of portable transmitter devices, including portable telephones. For consumer products, the applicable limit is 1.6 mW/g for an uncontrolled environment and 8.0 mW/g for an occupational/controlled environment as recommended by the ANSI/IEEE standard C95.1-1992 [6]. According to the Supplement C of OET Bulletin 65 “Evaluating Compl…

Text truncated - open the document above for the full version.

Date/Time: 06/02/04 19:56:20 Test Laboratory: Compliance Certification Services Inc. Touch-b mode DUT: Tablet PC; Type: CA27; Serial: N/A Communication System: IEEE 802.11b; Frequency: 2472 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2462 MHz; σ = 1.94 mho/m; ε r = 50.9; ρ = 1000 kg/m 3 Air Temperature:24.5 deg C;Liquid Temperature:23.5 deg C Phantom section: Flat Section DASY4 Configuration: z Probe: ES3DV2 - SN3023; ConvF(4.1, 4.1, 4.1); Calibrated: 9/23/2003 z Sensor-Surface: 4mm (Mechanical Surface Detection) z Electronics: DAE3 Sn427; Calibrated: 3/15/2004 z Phantom: SAM 34; Type: SAM V4.0; Serial: TP-1150 z Measurement SW: DASY4, V4.2 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 112 CH=11 11M 2/Area Scan (7x8x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 4.14 V/m; Power Drift = 0.2 dB Maximum value of SAR (measured) = 0.072 mW/g CH=11 11M 2/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 4.14 V/m; Power Drift = 0.2 dB Maximum value of SAR (measured) = 0.069 mW/g Peak SAR (extrapolated) = 5.56 W/kg SAR(1 g) = 0.110 mW/g; SAR(10 g) = 0.028 mW/g Page1 Page2 Date/Time: 06/02/04 19:56:19 Test Laboratory: Compliance Certification Services Inc. 15mm-b mode Test Configuration 2 Page1 Date/Time: 06/02/04 19:56:19 Test Laboratory: Compliance Certification Services Inc. 15mm-b mode DUT: Tablet PC; Type: CA27; Serial: N/A Communication System: IEEE 802.11b; Frequency: 2412 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2412 MHz; σ = 1.94 mho/m; ε r = 50.9; ρ = 1000 kg/m 3 Air Temperature:24.5 deg C;Liquid Temperature:23.5 deg C Phantom section: Flat Section DASY4 Configuration: z Probe: ES3DV2 - SN3023; ConvF(4.1, 4.1, 4.1); Calibrated: 9/23/2003 z Sensor-Surface: 4mm (Mechanical Surface Detection) z Electronics: DAE3 Sn427; Calibrated: 3/15/2004 z Phantom: SAM 34; Type: SAM V4.0; Serial: TP-1150 z Measurement SW: DASY4, V4.2 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 112 CH=Low 11M/Area Scan (7x9x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 3.74 V/m; Power Drift = 0.2 dB Maximum value of SAR (measured) = 0.060 mW/g CH=Low 11M/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 3.74 V/m; Power Drift = 0.2 dB Maximum value of SAR (measured) = 0.075 mW/g Peak SAR (extrapolated) = 0.202 W/kg SAR(1 g) = 0.070 mW/g; SAR(10 g) = 0.031 mW/g Page1 Page2 Date/Time: 06/02/04 19:56:19 Test Laboratory: Compliance Certification Services Inc. 15mm-b mode DUT: Tablet PC; Type: CA27; Serial: N/A Communication System: IEEE 802.11b; Frequency: 2437 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2437 MHz; σ = 1.94 mho/m; ε r = 50.9; ρ = 1000 kg/m 3 Air Temperature:24.5 deg C;Liquid Temperature:23.5 deg C Phantom section: Flat Section DASY4 Configuration: z Probe: ES3DV2 - SN3023; ConvF(4.1, 4.1, 4.1); Calibrated: 9/23/2003 z Sensor-Surface: 4mm (Mechanical Surface Detection) z Electronics: DAE3 Sn427; Calibrated: 3/15/2004 z Phantom: SAM 34; Type: SAM V4.0; Serial: TP-1150 z Measurement SW: DASY4, V4.2 Build 44; Postprocessing SW: SEMCAD, V1.8 Build 112 CH=Mid 11M/Area Scan (7x9x1): Measurement grid: dx=15mm, dy=15mm Reference Value = 2.98 V/m; Power Drift = -0.0 dB Maximum value of SAR (measured) = 0.040 mW/g CH=Mid 11M/Zoom Scan (5x5x7)/Cube 0: Measurement grid: dx=7.5mm, dy=7.5mm, dz=5mm Reference Value = 2.98 V/m; Power Drift = -0.0 dB Maximum value of SAR (measured) = 0.050 mW/g Peak SAR (extrapolated) = 0.078 W/kg SAR(1 g) = 0.043 mW/g; SAR(10 g) = 0.019 mW/g Page1 Page2 Date/Time: 06/02/04 19:56:19 Test Laboratory: Compliance Certification Services Inc. 15mm-b mode DUT: Tablet PC; Type: CA27; Serial: N/A Communication System: IEEE 802.11b; Frequency: 2462 MHz;Duty Cycle: 1:1 Medium parameters used: f = 2462 MHz; σ = 1.94 mho/m; ε r = 50.9; ρ = 1000 kg/m 3 Air Temperature:24.5 deg C;Liquid Temperature:23.5 deg C Phantom section: Flat Section DASY4 Configuration: z Probe: ES3DV2 - SN3023; ConvF(4.1, 4.1, 4.1); Calibrated: 9/23/2003 z Sensor-Surface: 4mm (Mechanical Surface Detection) z Electronics: DAE3 Sn427; Calibrated: 3/15/2004 z Phantom: SAM 34; Type: SAM V4.0; Serial: TP-1150…

Text truncated - open the document above for the full version.