MMA1001ZCB TRANSCEIVER

2 T T a a b b l l e e o o f f C C o o n n t t e e n n t t s s How to install your Midland mobile CB.................................. 3 Installation and Operating Accessories: ........................................... 4 Where to Locate your CB Transceiver. ............................................ 4 Mechanical Mounting. ...................................................................... 5 Power Wiring (negative ground only). .............................................. 5 Installation of Microphone Hanger.................................................... 6 Antenna: ................................................................................... 6 How to select, position install and tune the right one for you. .......... 6 Antenna installation. ......................................................................... 8 Tuning your antenna. ....................................................................... 8 Factors affecting CB range ..................................................... 8 Noise:........................................................................................ 8 Midland MODEL 1001Z CB Operating Controls..................... 9 Front Panel Controls .............................................................. 9 Back Panel.............................................................................. 11 Transceiver Operation ........................................................... 11 Technical Specifications ...................................................... 13 General........................................................................................... 13 Transmitter ..................................................................................... 14 Service ................................................................................... 12 Limited Warranty ................................................................... 13 Midland MODEL 1001Z 40-Channel mobile Citizens Band transceiver For your protection, the space below is provided for you to record the Serial Number of this product, which is located on the rear of the radio. After recording this number, keep this record for future reference along with the sales receipt. The sales receipt is needed should your radio ever need service. FCC I.D. MMA1001 Serial Number:____________________ 3 W W e e l l c c o o m m e e t t o o t t h h e e W W o o r r l l d d o o f f M M i i d d l l a a n n d d E E l l e e c c t t r r o o n n i i c c s s Congratulations on your purchase of a state-of-the-art mobile CB radio. In the years ahead, you can expect to realize time and again why Midland holds the front running position among CB users everywhere. You will come to know that Midland power is more than just a slogan, but the heading of long list of hearable, seeable benefits. As your Midland CB experience unfolds and grows we hope you will remember that CB is only one kind of electronic excellence available under the Midland name. Your 40 channel CB represents the state of the art in high tech engineering. The unit incorporates microprocessor controlled PLL circuitry for precise tuning. H H o o w w t t o o I I n n s s t t a a l l l l y y o o u u r r M M i i d d l l a a n n d d M M o o b b i i l l e e C C B B This transceiver may be installed in any 12-volt negative ground- system car or truck. Most current U.S. and foreign vehicles use a negative system, but some older models and some newer large trucks may have a positive ground. Check the requirements for your vehicle before you begin installation. Generally, you have a negative-ground system if the minus ( - ) battery terminal is connected to the motor block. Contact your dealer in the event you are unable to determine your vehicle’s polarity system. 4 I I n n s s t t a a l l l l a a t t i i o o n n a a n n d d O O p p e e r r a a t t i i n n g g A A c c c c e e s s s s o o r r i i e e s s F F u u r r n n i i s s h h e e d d w w i i t t h h y y o o u u r r M M i i d d l l a a n n d d C C B B : : 1. Easy removal mounting bracket system. 2. Microphone bracket system. 3. All main-unit and microphone mounting hardware needed for normal installation. 4. Plug-in microphone with coil cord. 5. FCC part 95, Subpart D. 6. Owner’s Manual. W W h h e e r r e e t t o o L L o o c c a a t t e e y y o o u u r r C C B B T T r r a a n n s s c c e e i i v v e e r r Your new Midland CB is designed to be installed under the dash or vertically on a console of your vehicle. Safety and convenience are the primary considerations in deciding exactly where to locate your radio. Caution: Be sure that the unit is located so that it does not interfere with the driver, supplemental restraint systems (air bags) or impair access to any controls. Connecting cables must be routed and secured in such a manner as not to interfere with the operation of the brake, accelerator or other controls. Interference from either the unit or connecting cables may contribute to the loss of control of the vehicle. 5 M M e e c c h h a a n n i i c c a a l l M M o o u u n n t t i i n n g g Step 1: Heeding the caution, use the mounting bracket as a template for marking the location of screw holes under the dash. Use an awl, nail or other sharp pointed object to mark the hole locations. Step 2: Drill a 1/8” hole for each screw hole in the mounting bracket. Attach the bracket to the dash with the Phillips head sheet metal screws provided. , Extreme care should be exercised when drilling into the dash to avoid damage to under-dash electronic ignition, cruise control, instrument and / or accessory wiring. Step 3: Position the main unit between the bracket arms in line with the retention knobs. Set the angle for optimum operating comfort and accessibility. Step 4: Tighten the retention knobs P P o o w w e e r r W W i i r r i i n n g g ( ( n n e e g g a a t t i i v v e e g g r r o o u u n n d d o o n n l l y y ) ) Step 1: If you have not determined whether your vehicle has a negative or positive grou…

Text truncated - open the document above for the full version.

5900 Parretta Drive ● KANSAS CITY, MISSOURI ● 64120 TELEPHONE: (816) 241-8500 ● FAX: (816) 241-5713 EMAIL: [email protected] WEBSITE: www.midlandradio.com Midland Radio Corporation 5900 Parretta Drive, Kansas City, MO. 64120 Phone: (816) 241-8500 Fax: (816) 241-5713 Website: wwwl.midlandradio.com E-Mail: [email protected] June 15, 2010 Equipment Authorization Division Office of Engineering and Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Ref: FCC ID: MMA1001Z Request for Confidentiality Dear Sirs: With regard to the referenced application, Midland Radio Corporation is requesting confidentiality of certain sections of the accompanying documents. The documents for which Midland Radio Corporation is requesting confidentiality are: Schematic Diagram Block Diagram Operational Descriptions This request is made under the provisions of Section 0.457(d) of the Commission’s Rules, and Section 552(b)(4) of the Freedom of Information Act. The material for which confidentiality is requested falls within the scope of Section 552(b)(4) as trade secrets and includes material covered by Section 0.459 of the Commission’s Rules. Sincerely, David Kingsolver, Director of Engineering

APPLICANT: MIDLAND RADIO CORP. FCC ID: MMA1001Z EXTERNAL PHOTOS

APPLICANT: MIDLAND RADIO CORP. FCC ID: MMA1001Z INTERNAL PHOTOS

ALIGNMENT PROCEDURE 1. VCO LOCKING VOLTAGE -SET UNIT CHANEL 40 TRANSMIT MODE -CHECK VOLTAGE AT R20, C504, R608 -ADJUST L4 FOR VOLTAGE TO BE OBTAINED 2.0Vdc. 2. TX POWER -SET UNIT CHANEL 20 -NO MODULATION -ADJUST L5, L6, L801 FOR MAXIMUM 3. TX FREQUENCY -SET UNIT CHANEL 20 TRANSMIT MODE -NO MODULATION -MEASURE FREQUENCY -ADJUST CT1 UNTIL FREQUENCY TO BE EQUAL 27.205MHZ 4. TX AM MODULATION -SET UNIT CHANEL 20 -TX WITH MODULATION -MEASURE % MODULATION -ADJUST RV2 FOR MODULATION OBTAIN 95% 5. TX SIGNAL METER -SET UNIT CHANEL 20 -TX NO MODULATION -SEE SIGNAL METER BAR -ADJUST RV4 UNTIL S-METER TO BE EQUAL TO 4.0W 6. RX SENSITIVITY -SET UNIT CHANEL 19 VOLUME MAX SQUELCH MIN -SET SIGNAL GENARATOR FREQUENCY 27.185MHZ MOD AM 30% AMPITUDE LEVEL 1UV -MEASURE SENSITIVITY -ADJUST L1, L102, L104, L2, L3 FOR MAXIMUM SENSITIVITY 7. SQUELCH -SET UNIT CHANEL 19 TO VOLUME AND SQUELCHE MAX -SET SIGNAL GENARATOR FREQUENCY 27.185MHZ MOD AM 30% AMPITUDE LEVEL 1000 UV -ADJUST RV1 UNTIL APPEAR SIGNAL ON 8. RX SIGNAL METER -SET UNIT CHANEL 19 -SET SIGNAL GENARATOR FREQUENCY 27.185MHZ NO MODULATION AMPITUDE LEVEL 100UV -SEE SIGNAL METER BAR -ADJUST RV3 UNTIL S-METER TO BE EQUAL TO S-9

Sheet1 DEV OP MENT : UNFINISHED P A R T S L IS T DES N : UNFINISHED ============== = === = TEC IQUE : NO DATA S/W ER SION : UNDEFINED MO D C ODE CBM248MIDLAND 1001RF Cost down New PCB ( no Module ) ---- ------------------------------------------------------------------------------------------------------------ SEQ L EVEL PART-NO. NAME & DESCRIPTION ICP Q'TY REFERENCE-NO ---- ------------------------------------------------------------------------------------------------------------ 1 2 CBM248COCOVER ASS'Y 1.000 3 12-00006-81SPEAKER 8 OHM 1W L66AC-8-7C13R ICP1.000 3 60-00008-01MACHINE SCREW M2.6x4 ZINC PLATE ICP4.000 ESCUTCHEON & MAIN BODY:4 3 60-00053-02TAPPING SCREW 1010 M3x6 RoHS ZINC ICP3.000 SPK.MTG:3 3 60-00067-02TAP TITE SCREW BM3x8 BLACK ICP8.000 COVER & MAIN BODY MTG 3 81-00013-00COVER BOTTOM ABS 94HB BLK 1.000 3 81-00014-00 UPPER COVER ABS94HB L380-9001 BLACK 1.000 3 72-00005-00HOLDER(SPK MTG) EGI US COATING T1 ICP3.000 SPK. MTG:3 3 86-00007-00E.S.C ABS 94HB BLACK 1.000 3 84-00018-00WINDOW ACRYL ICP1.000 3 83-00020-00KNOB SLIDE ABS 94HB L380-9001 BLK 2.000 3 83-00022-00KNOB SQL ABS 94HB L380-9001 BLK ICP1.000 3 83-00008-00 KNOB CHANNEL ABS 94 HB LUCKY380-9001 BLK ICP2.000 3 83-00024-00KNOB VOL ABS 94HB BLK ICP1.000 3 78-00007-00SPRING(VOL.SW MTG) SK5 T0.25 ICP1.000 3 90-00007-00 FELT STICKER 6x110xT=0.5MM FELT STICKER ICP4.000 COVER MTG(REAR) 3 90-00008-00FELT FELT BLACK Ø65xT=0.15MM. ICP1.000 AIR VENT 3 92-00006-00DOUBLE TAPE 3M DOUBLE TAPE T=0.1MM ICP1.000 2 2 CBM248XTLCRYSTAL ASS'Y 1.000 3 07-00004-01 CRYSTAL SZJF-10.24M-9U-17-1-30 ICP1.000 X1 3 2 CBM248FBFRONT BODY ASS'Y 1.000 3 03-00035-00TRANSISTOR 2SC2078(F) ICP1.000 Q14 3 10-00014-01I.C YW UTC7217 DIP ICP1.000 IC2 3 20-00002-00JACK DC TC38-078-01 ICP2.000 J1.2 3 15-00005-01CONNECTOR SWCN-1601 ICP1.000 3 26-00001-00MICA MICA 13x15xT=0.3MM ICP1.000 3 16-00006-03POWER CORD ASS'Y AS2468 20AWG/2P PVC WIRE 1500M 1.000 3 60-00028-01MACHINE SCREW 1010 M3x10 RoHS ZINC ICP2.000 TR MTG:1 IC MTG:1 3 60-00038-02TAPPING SCREW M2.6x8 ZINC PLATE ICP2.000 SUB PCB MTG:2 3 60-00053-02TAPPING SCREW 1010 M3x6 RoHS ZINC ICP2.000 MAIN PCB:2 3 62-00004-00NUT CARBON STEEL M3 RoHS ZINC ICP2.000 TR IC MTG 3 63-00014-00WASHER SPRING CARBON STEEL M3 RoHS ZINC ICP2.000 TR IC MTG 3 70-00003-00 MAIN BODY EGI T=1.0 ICP1.000 3 82-00013-00CORD STOPPER PP BLACK 1.000 3 73-00003-00HEAT SINK ALP3 13x26xT=2.0 MM. ICP1.000 3 85-00014-00BUSHING NYLON66+GLASS ICP1.000 4 2 CBM248MAMIC ASS'Y 1.000 3 01-00074-00CHIP CERAMIC 0.001UF GRM39 X7R102K 50 ICP1.000 C2 3 13-00000-00MIC CONDENSER HZ9765502 ICP1.000 3 24-00002-00CURLED CORD 19/0.10x3C+35/0.10BC CURLED CO ICP1.000 3 15-00004-01CONNECTOR PLUG SWCN-0901-BNC ICP1.000 3 32-00001-11SW PUSH CPS-2210C (77-0 ICP1.000 SW5 3 60-00003-03SCREW(SECURING) ABS94HB M6X10(P=1) ICP2.000 3 60-00036-02TAPING SCREW M2.6x12 NICKEL PLATE ICP4.000 3 60-00038-02TAPPING SCREW M2.6x8 ZINC PLATE ICP3.000 3 60-00056-02TAPPING SCREW1010 M3X10 RoHS NICKEL ICP2.000 3 60-00061-02TAPPING SCREW1010 M5X12 RoHS ZINC ICP3.000 3 60-00069-02WOOD SCREW M2.6x14 NICKEL PLATE ICP1.000 3 63-00002-00WASHER RUBBER BLACK Ø7XØ25XT1.5MM. ICP2.000 3 63-00020-00WASHER CARBON STEEL M3 RoHS NICKEL ICP2.000 3 63-00022-00WASHER CARBON STEEL M5 RoHS ZINC ICP3.000 3 81-00007-00UPPER COVER(MIC) ABS 94HB BLK ICP1.000 3 81-00010-00BOTTOM COVER (MIC) ABS 94HB BLK ICP1.000 3 71-00001-00BRACKET(MIC MTG) SPC 60X35XT1 ICP1.000 Page 1 Sheet1 3 71-00008-00BRACKET(SET MTG) SPC 30X235XT1.5 BLK-PAINT ICP1.000 3 82-00001-00HOLDER(MIC) PC BLK ICP1.000 3 82-00010-00LEVER(MIC) PC BLACK ICP1.000 3 95-00003-00NAME PLATE(MIC) ALP3 11X36XT=0.4MM. ICP1.000 3 95-00015-00NAME PLATE(MIC) PVC 12.8x23.9xT0.4 CLEAR ICP1.000 3 85-00004-00BEZEL ABS BLK ICP1.000 3 85-00011-00GRILL CAP ABS 94HB L380-9001 BLK ICP1.000 3 85-00024-00WIRE CLAMP (CORD) NYLON ICP1.000 3 89-00013-00CUSHION Ø22xT4 SPONGE STICKER ICP1.000 3 89-00028-00RUBBER RUBBER BLACK Ø9.5XØ3 ICP1.000 3 90-00005-00FELT FELT 34x36xT=0.15MM ICP1.000 3 97-00014-00BOX MIC SW2E 221(W)X70(D)X ICP1.000 397-00132-00PADSW "B" 60(W)x120(D)1.000 398-00005-02CELLOPHANEP.P CELLOPHANE 100X100XT0.05 MICP2.000ACCESSORY MIC:1,ACCESSORY SCREW:1 3 98-00013-03CELLOPHANEP.P CELLOPHANE 100X200XT0.05 MICP1.000 MICROPHONE:1 5 2 CBM248MPA MAIN PCB AUTO ASS'Y 1.000 3 00-00100-02FILM RESISTOR 10 1/ 2W 5% ST MINI ICP1.000 R999 3 01-00000-11ELECT CAPACITOR 0.1UF 50V 20% 5X11 ICP1.000 C39 3 01-00004-11ELECT CAPACITOR 1UF 50V 20% 5X11 ICP2.000 C55.209 3 01-00006-11ELECT CAPACITOR 10UF 16V 20% 5X11 ICP6.000 C11.51.79.204.303.957 3 01-00010-11ELECT CAPACITOR 1000UF 16V 20% 10X16 ICP2.000 C63.95 3 01-00012-11ELECT CAPACITOR 100UF 16V 20% 6.3X11 ICP4.000 C3.27.65.69 3 01-00018-11ELECT CAPACITOR 22UF 16V 20% 5X11 ICP2.000 C1.38 3 01-00022-11ELECT CAPACITOR 220UF 16V 20% 6.3X11 ICP1.000 C62 3 01-00026-11ELECT CAPACITOR 3.3UF 50V 20% 5X11 ICP1.000 C50 3 01-00027-11ELECT CAPACITOR 33UF 16V 20% 5X11 ICP3.000 C45.48.52 3 01-00029-11ELECT CAPACITOR 4.7UF 50V 20% 5X11 ICP1.000 C9 3 01-00034-11ELECT CAPACITOR 47UF 16V 20% 5X11 ICP3.000 C26.33.61 3 01-00002-01DISK CERAMIC 0.01UF DD312B 103K 50V ICP1.000 C92 3 02-00000-31COIL AXIAL AL0307-2R2K ICP1.000 RFC4 3 02-00002-31COIL AXIAL AL0307-6R8J (6.8uH +/-5%) ICP1.000 RFC8 3 02-00005-31COIL AXIAL 100UH ±10% ICP1.000 RFC1 3 02-00014-31COIL AXIAL 0.39UH:LAL02TBR39K ICP1.000 RFC3 302-00015-31COIL AXIAL 6.8UH:LAL02TB6R8K ICP1.000 RFC2 3 05-00009-01ZENER DIODE 1N5239B (9.1V) ICP1.000 DZ1 3 05-00001-31DIODE RECTIFIER 1N4004 ICP2.000 D9.16 6 2 CBM248MPM MAIN PCB MANUAL ASS'Y 1.000 3 00-00121-80METAL OXIDE RESISTOR 120 1W 5% ST 1.000 R3 3 00-00150-81METAL OXIDE RESISTOR 15 2W 5% ST 1.000 R55 3 00-00501-70THERMISTOR DISK 500 KC5C150L ICP1.000 TH301 3 03-00026-00TRANSISTOR KTC1006 ICP1.000 Q13 3 10-00006-01I.C LED DRIVER LA2284L-G09-T 1.000 IC301 3 10-00027-01I.C LC7185-8750 ICP1.000 IC1 3 05-00008-01ZENER DIODE 1N4733A ICP1.000 DZ2 3 05-00001-21DIODE GE 1N60P ICP1.000 D201 3 08-00001-01CERAMIC FILTER LT455HTU ICP1.000 CF2 3 08-00004-01FILTER CE…

Text truncated - open the document above for the full version.

Page 1 of 4 FCC ID: MMA1001Z FCC RF Exposure Requirements General information: FCC ID: MMA1001Z Device category: Mobile per Part 2.1091 Environment: Uncontrolled Exposure Mobile devices that operate under Part 95 of this chapter are subject to routine environmental evaluation for RF exposure prior to equipment authorization or use if they operate at frequencies of 1.5 GHz or below and their effective radiated power (ERP) is 1.5 watts or more. However, compliance with the power density limits of 1.1310 is not required. Antenna: The manufacturer does not specify an antenna. In this configuration the typical antenna for this device has a gain of 0 dBi. Although 0 dBi gain antenna is typical for the installation any gain up to 5 dBi could be used and still maintain compliance. 5 dBi will be used in the equation on the following page to demonstrate this. This device has provisions for operation in mobile, or a fixed location. Configuration Antenna p/n Type Duty cycle Max. Gain (dBi) mobile Any omni 50% up to3 Operating configuration and exposure conditions: The conducted output power is 4. Watts. The maximum duty cycle is set as a function of talking versus listening and is taken at 50 %. Part 2.1091 states that devices are excluded from routine evaluation if the EIRP is less than 2.46Watt (or 1.5WERP). Mobile Operation: A typical mobile installation consists of an antenna system with a coaxial cable of the type RG 58/U which has a loss of 1dB for a length of 30 feet. Page 2 of 4 FCC ID: MMA1001Z MPE Calculation: The minimum separation distance is calculated as follows: The limit for a uncontrolled / general population exposure environment above 180/f^2 mW/cm 2 . Page 3 of 4 FCC ID: MMA1001Z Channel frequency: 27 MHz The conducted power output is 5. Watts The coax loss was taken as 1 dB. Antenna gain was taken as 3 dBi 50% talk time in 30 minutes Page 4 of 4 FCC ID: MMA1001Z Conclusion: The device complies with the MPE requirements by providing a safe separation distance of 36 cm between the antenna, including any radiating structure, and any persons when normally operated . This is based on a typical installation and an antenna with 3 dBi of gain. This device is approved with emissions having a source-based time-averaging duty factor not exceeding 50%.

FCC PART 95 SUBPART D AND IC RSS-136 TEST REPORT FOR CB TRANSCEIVERS APPLICANT MIDLAND RADIO CORPORATION 5900 PARRETTA DRIVE KANSAS CITY MISSOURI 64120 USA FCC ID MMA1001Z IC 3690A-1001Z MODEL NUMBER 1001z PRODUCT DESCRIPTION CB TRANSCEIVER DATE SAMPLE RECEIVED 6/9/2010 DATE TESTED 6/28/2010 TESTED BY Nam Nguyen APPROVED BY Mario R. de Aranzeta TIMCO REPORT NO. 1352AT10TestReport.doc TEST RESULTS PASS FAIL THE ATTACHED REPORT SHALL NOT BE REPRODUCED EXCEPT IN FULL WITHOUT THE WRITTEN APPROVAL OF TIMCO ENGINEERING, INC. 849 NW STATE ROAD 45 NEWBERRY, FL 32669 USA PH: 888.472.2424 OR 352.472.5500 FAX: 352.472.2030 EMAIL: [email protected] HTTP://WWW.TIMCOENGR.COM Testing Certificate # 0955-01 APPLICANT: MIDLAND RADIO CORPORATION FCC ID: MMA1001Z IC: 3690A-1001Z REPORT #: M\MidlandRadio_MMA\1352AT10\1352AT10TestReport.doc Page 2 of 19 TABLE OF CONTENTS GENERAL REMARKS ................................................................................................3 GENERAL INFORMATION .........................................................................................4 TEST ENVIRONMENT ...............................................................................................5 TEST SETUP SUMMARY ...........................................................................................5 EQUIPMENT LIST .....................................................................................................6 TEST PROCEDURE ..................................................................................................7 RF POWER OUTPUT .................................................................................................8 MODULATION CHARACTERISTICS ...........................................................................9 AUDIO FREQUENCY RESPONSE ..............................................................................9 AUDIO LOW PASS FILTER RESPONSE .................................................................... 10 AUDIO INPUT VS MODULATION ............................................................................. 11 OCCUPIED BANDWIDTH ........................................................................................ 12 SPURIOUS EMISSIONS AT ANTENNA TERMINALS (CONDUCTED) ........................... 14 FIELD STRENGTH OF SPURIOUS EMISSIONS ........................................................ 16 METHOD OF MEASUREMENT ................................................................................ 18 FREQUENCY STABILITY ......................................................................................... 19 APPLICANT: MIDLAND RADIO CORPORATION FCC ID: MMA1001Z IC: 3690A-1001Z REPORT #: M\MidlandRadio_MMA\1352AT10\1352AT10TestReport.doc Page 3 of 19 GENERAL REMARKS The attached report shall not be reproduced except in full without the written permission of Timco Engineering Inc. The test results relate only to the items tested. Summary The device under test does: fulfill the general approval requirements as identified in this test report not fulfill the general approval requirements as identified in this test report Attestations This equipment has been tested in accordance with the standards identified in this test report. To the best of my knowledge and belief, these tests were performed using the measurement procedures described in this report. All instrumentation and accessories used to test products for compliance to the indicated standards are calibrated regularly in accordance with ISO 17025 requirements. Testing Certificate # 0955-01 I attest that the necessary measurements were made, under my supervision, at: Timco Engineering Inc. 849 NW State Road 45 Newberry, Fl 32669 Authorized Signatory Name: Mario de Aranzeta C.E.T. Compliance Engineer/ Lab. Supervisor Date: 7/1/2010 APPLICANT: MIDLAND RADIO CORPORATION FCC ID: MMA1001Z IC: 3690A-1001Z REPORT #: M\MidlandRadio_MMA\1352AT10\1352AT10TestReport.doc Page 4 of 19 GENERAL INFORMATION DUT Specification DUT Description CB TRANSCEIVER FCC ID MMA1001Z IC 3690A-1001Z Model Number 1001z Serial Number N/A Operating Frequency 26.965-27.405 MHz No. of Channels 40 Type of Emission 6KOOA3E Bn = 2M M = 3000 Bn = 6000 Modulation AM DUT Power Source 110–120Vac/50– 60Hz DC Power Battery Operated Exclusively Test Item Prototype Pre-Production Production Type of Equipment Fixed Mobile Portable APPLICANT: MIDLAND RADIO CORPORATION FCC ID: MMA1001Z IC: 3690A-1001Z REPORT #: M\MidlandRadio_MMA\1352AT10\1352AT10TestReport.doc Page 5 of 19 TEST ENVIRONMENT Test Facility Timco Engineering, Inc. 849 NW State Road 45 Newberry, FL 32669 USA. Test Condition in the laboratory Temperature: 26ºC Relative humidity: 50% TEST SETUP SUMMARY Test Setup Diagram/ Description The DUT was placed on the turntable per setup per ANSI C63.4: 2003. A test set up photo is provided for clarification. Deviation from the standard/procedure No deviation Modification of DUT No modification Applicable Standards EIA/TIA-382-A, FCC CFR 47 PART 95, RSS-GEN, RSS-136 APPLICANT: MIDLAND RADIO CORPORATION FCC ID: MMA1001Z IC: 3690A-1001Z REPORT #: M\MidlandRadio_MMA\1352AT10\1352AT10TestReport.doc Page 6 of 19 EQUIPMENT LIST Device Manufacturer Model Serial Number Cal/Char Date Due Date 3-Meter Semi- Anechoic Chamber Panashield N/A N/A Listed 03/10/10 03/10/12 Analyzer Tan Tower Quasi-Peak Adapter HP 85650A 3303A01690 CAL 11/22/09 11/22/11 Analyzer Tan Tower RF Preselector HP 85685A 3221A01400 CAL 11/21/09 11/21/11 Analyzer Tan Tower Spectrum Analyzer HP 8566B Opt 462 3138A07786 3144A20661 CAL 11/24/09 11/24/11 Analyzer Tan Tower Preamplifier HP 8449B-H02 3008A00372 CAL 11/21/09 11/21/11 Coaxial Cable #64 Semflex Inc. 60637 Timco #64 CHAR 3/30/09 3/30/11 Antenna: Dipole Kit Electro-Metrics TDA-30/1- 4 152 CAL 3/3/09 3/3/12 Antenna: Dipole Kit Electro-Metrics TDA-30/1- 4 153 CHAR 4/5/09 4/5/12 Hygro- Thermometer Extech 445703 0602 CAL 1/30/09 1/30/11 Modulation Analyzer HP 8901A 3435A06868 CAL 5/9/09 5/9/11 Digital Multimeter Fluke FLUKE-77- 3 7951040…

Text truncated - open the document above for the full version.