MMALXT535PAGMRS / FRS

Welcome to the world of Midland electronics Congratulations on your purchase of a high quality MIDLANDproduct. Your 2-way radio represents state-of-the-art high-techengineering. Designed for GMRS (General Mobile Radio Service)operation, this compact package is big on performance. It is aquality piece of electronic equipment, skillfully constructed with thefinest components. The circuitry is all solid-state and mounted on arugged printed circuit board. Your two-way radio is designed forreliable and trouble-free performance for years to come.Features- 22 GMRS/FRS Channel- Call Alert - Scan Function- Roger Beep Tone- Silent Operation- Keypad Lock- Power HI/LO Settings- Auto Squelch- Speaker / Microphone Jacks- Battery Life Extender- Battery Low Indicator This device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) this device does notcause harmful interference, and (2) this radio must accept anyinterference that may cause undesired operation.To maintain compliance with FCC’s RF exposure guidelines, forbody-worn operation, this radio has been tested and meets theFCC RF exposure guidelines when used with Midland RadioCorp. accessories supplied or designated for this product. Use ofother accessories may not ensure compliance with FCC RFexposure guidelines. IMPORTANT NOTICE, FCC LICENSE REQUIRED FOR GMRS OPERATION(Only Applicable for GMRS Radio Use in the United States)The radios operates on GMRS (General Mobile Radio Service) frequencieswhich require an FCC (Federal Communications Commission) license. You mustbe licensed prior to operating on channels 1 - 7 or 15 - 22, which comprise theGMRS channels of the radios. Serious penalties could result from unlicensed useof GMRS channels, in violation of FCC rules, as stipulated in theCommunications Acts Sections 501 and 502 (amended).You will be issued a call sign by the FCC which should be used for stationidentification when operating the radio on GMRS channels. You should alsocooperate by engaging in permissible transmissions only, avoiding channelinterference with other GMRS users, and being prudent with the length of yourtransmission time.To obtain a license or ask questions about the license application, contact theFCC at 1-888-CALL FCC or go to the FCC's website: http://www .fcc.gov and request form 605 . Exposure To Radio Frequency EnergyYour Midland radio is designed to comply with the following national andinternational standards and guidelines regarding exposure of human beings toradio frequency electromagnetic energy:- United States Federal Communications Commission, Code of Federal Regulations: 47 CFR part 2 sub-part J - American National Standards Institute (ANSI)/Institute of Electrical & Electronic Engineers (IEEE) C95. 1-1992 - Institute of Electrical and Electronic Engineers (IEEE) C95. 1-1999 Edition- National Council on Radiation Protection and Measurements (NCRP) of the United States, Report 86, 1986 - International Commission on Non-lonizing Radiation Protection (ICNIRP) 1998 To control your exposure and ensure compliance with the general population oruncontrolled environment exposure limits, transmit no more than 50% of thetime. The radio generates measurable RF energy exposure only whentransmitting. IMPORTANT: Changes or modifications to this unit not expressly approved by MIDLAND RADIO CORP. could void your right to operate this unit. Your radio is set up to transmit a regulated signal on an assigned frequency. It is againstthe law to alter or adjust the settings inside the COMMUNICATOR to exceedthose limitations. Any adjustment to your radio must be made by qualifiedtechnicians. LCD DISPLA Y 1. LOW BATTERY ICON – Indicates the battery level is low. 2. TRANSMIT (TX) ICON – Indicates radio is transmitting a signal. 3. CHANNEL NUMBER – Changes from 1~22 on GMRS/FRS band. 4. KEY LOCK ICON – Indicates KEY LOCK mode is on. 5. RECEIVE (RX) ICON – Indicates radio is receiving a transmission. 6. TRANSMIT POWER LEVEL ICON – Indicates TX Power setting (H/L) 1 CONTR OLS 7. PTT Button – Press and hold to transmit voice communication. 8. CALL/LOCK Button – Press to send a CALL Alert signal. Press and hold toturn KEY LOCK on/off. 9. MIC – Built-in microphone. 10. SPEAKER – Built-in speaker. 11. ANTENNA12. EXTERNAL SPEAKER/MIC/CHG. JACK 13. POWER / MENU Button – Press and hold for at least 3 seconds to turn theradio on/off. Press momentarily toaccess Menu mode. 14. SCAN Button – Press to enter SCAN mode. 15. UP s and DOWN t Buttons – Make adjustments in MENU mode. 14 1312 10 98 7 65 4 32 11 BA T TER Y INS T ALLA TION Your radio operates with either a NiMH battery pack or optional 4 AAAalkaline batteries. The belt clip should be removed to ease installation orremoval of the batteries. To install the batteries:1. With the back of the radio facing you, remove the belt clip (see diagram on the next page) for easy access, then remove the Battery Cover by pressing down on the top center and sliding it down from theradio. 2. Insert 4 AAA batteries observing the polarity as shown. Installing the batteries incorrectly will prevent the unit from operating or may damage the unit. 3. Return the Battery Cover by sliding it up on the radio. Replace the belt clip, making sure it locks into place. 15 MM II DD LL AA NN DD RR AA DD II OO CC OO RR PP OO RR AA TT II OO NN 5900 Parretta Drive Kansas City, MO 64120 Call 816.241.8500 We’d love to hear from you! Let us know what you think of your new Midland product on or by visiting us at midlandusa.com Note: Features & Specifications are subject to change withoutnotice. MIDLAND is not responsible for unintentional errors oromissions on its packaging. BATTERYCOMPARTMENT BATTERYCOMPARTMENTCOVER Press here and push down to open BELT CLIPLOCK TABBELT CLIP LATCH INS T ALLING THE BEL T CLIP To install the BELT CLIP , slide the clip up into the slot on the back of the radio until the BELT CLIP LATCH clicks. To remove the BELT CLIP , press the LOCK TAB up, then gently pull…

Text truncated - open the document above for the full version.

Midland Radio Corporation 5900 Parretta Drive, Kansas City, Missouri United States 64120 Date: September 07, 2015 Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: MMALXT535PA Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Schematics Diagram(s) CONF APPENDIX_LXT535PA_Schematics.PDF Block diagram CONF APPENDIX_LXT535PA_Block diagram.PDF Operation description CONF APPENDIX_LXT535PA_Operation description.PDF The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Jeff Brame

Midland Radio Corporation 5900 Parretta Drive, Kansas City, Missouri United States 64120 September 07, 2015 Federal Communications Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 SUBJECT : Midland Radio Corporation FCC ID : MMALXT535PA Label Justification Letter Dear Sir/Madame, Because the device is so small that it is not practicable to place the statement specified under 15.19 statement request, the information required by this paragraph shall be placed in a prominent location in the User’s Manual. - The available label area on the device is limited because it is relatively small and has many contoured surfaces, keypads, LDC display, and other connectors. - The batteries are designed for easy removal and the label will be visible whenever the batteries are removed for replacement. - The label will be readily visible at the time of purchase because the device will be marketed without the battery installed. - FCC ID will be printed on the gift box which will be readily visible to the purchaser at the time of purchase. Sincerely, Jeff Brame Midland Radio Corporation 5900 Parretta Drive, Kansas City, Missouri United States 64120 Label and Location

www.kes.co.kr FCC ID.: MMALXT535PA Page 1 of 2 EUT Internal photographs Helical Antenna www.kes.co.kr FCC ID.: MMALXT535PA Page 2 of 2

GLOBAL LINK CORP. LTD. LXT535PA Series - Bill of Material Dwg. No. : LXT535PA-BOM-M-05 Rev. Date: 11/06/15 C1CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C10CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C104CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C11CHIP CAPACITOR 0402 X7R +/- 10%0.1UF (X7R)1YageoYageo C12CHIP CAPACITOR 0603 Y5V1UF1YageoYageo C122CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C125CHIP CAPACITOR 0402 X7R ±10%0.001UF1YageoYageo C13CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C133CHIP CAPACITOR 0805 X5R ±10%10UF/10V (05)1MurataASKO C14CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C140CHIP CAPACITOR 0402 X7R ±10%470P(X7R)1YageoYageoPA-LXT12-B002930-Jan-15 C142CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C144CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C145CHIP CAPACITOR 0402 X7R ±10%0.001UF1YageoYageo C148CHIP CAPACITOR 0402 NPO ±0.25PF5P1YageoYageo C15CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C16CHIP CAPACITOR 0603 Y5V1UF1YageoYageo C162CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C166CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C17CHIP CAPACITOR 0603 NPO ±0.25PF3P(03)1YageoYageoPA-LXT12-B002930-Jan-15 C172CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C173CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C174CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C177CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C178CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C179CHIP CAPACITOR 0402 NPO ±5%22P1YageoYageoPA-LXT12-B002930-Jan-15 C17ACHIP CAPACITOR 0402 NPO ±0.25PF1.5P1YageoYageo C18CHIP CAPACITOR 0603 Y5V2.2UF1YageoYageo C182CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C19CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C2CHIP CAPACITOR 0603 NPO ±5%100P(03)1YageoYageo C20CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C207CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C208CHIP CAPACITOR 0402 NPO ±5%33P1YageoYageo C209CHIP CAPACITOR 0402 NPO ±5%33P1YageoYageo C21CHIP CAPACITOR 0402 NPO ±0.25PF7P1YageoYageo C22CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C23CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C24CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C25CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C26CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C27CHIP CAPACITOR 0805 X5R ±10%10UF/10V (05)1MurataASKOPA-LXT12-B003411-Jun-15 C28CHIP CAPACITOR 0603 Y5V1UF1YageoYageo C29CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C3CHIP CAPACITOR 0402 X7R ±10%0.001UF1YageoYageo C30CHIP CAPACITOR 0603 NPO ±0.25PF6P(03)1YageoYageo C304CHIP CAPACITOR 0402 NPO ±0.25PF3P1YageoYageo C31CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageoPA-LXT12-B003411-Jun-15 C32CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageoPA-LXT12-B003411-Jun-15 C33CHIP CAPACITOR 0805 X5R ±10%10UF/10V (05)1MurataASKO C34CHIP CAPACITOR 0402 NPO ±5%15P1YageoYageoPA-LXT12-B002930-Jan-15 C35CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C36CHIP CAPACITOR 0402 NPO ±5%10P1YageoYageoPA-LXT12-B002930-Jan-15 C37CHIP CAPACITOR 0402 NPO ±0.25PF8P1YageoYageo C38CHIP CAPACITOR 0402 NPO ±5%10P1YageoYageoPA-LXT12-B002930-Jan-15 C39CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C3ACHIP CAPACITOR 0603 NPO ±0.25PF2P(03)1YageoYageoPA-LXT12-B002930-Jan-15 C4CHIP CAPACITOR 0402 NPO ±0.25PF3P1YageoYageoPA-LXT12-B002930-Jan-15 C40CHIP CAPACITOR 0402 NPO ±5%10P1YageoYageoPA-LXT12-B002930-Jan-15 C41CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C42CHIP CAPACITOR 0402 X7R ±10%0.01UF1YageoYageoPA-LXT12-B003411-Jun-15 C43Elect capacitor 470UF/6.3v (6x7)470uF/6.3V 6x7mm1SamconSamconPA-LXT12-B003010-Mar-15 C44CHIP CAPACITOR 0402 X7R ±10%0.0018UF1YageoYageo C45CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C46CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C47CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C48CHIP CAPACITOR 0805 X5R ±10%10UF/10V (05)1MurataASKO C49CHIP CAPACITOR 0402 X7R ±10%0.01UF1YageoYageo C5CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C50CHIP CAPACITOR 0603 Y5V1UF1YageoYageo C51CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C52CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C53CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C54CHIP CAPACITOR 0402 X7R ±10%0.001UF1YageoYageoPA-LXT12-B003411-Jun-15 C55CHIP CAPACITOR 0402 X7R +/- 10%0.1UF (X7R)1YageoYageo C56CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C57CHIP CAPACITOR 0402 X7R ±10%0.01UF1YageoYageo C58CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C6CHIP CAPACITOR 0603 NPO ±0.25PF6P(03)1YageoYageoPA-LXT12-B002930-Jan-15 C60CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C61CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C62CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C63CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C64CHIP CAPACITOR 0402 NPO ±0.25PF7P1YageoYageo C65CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C67CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C68CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C6ACHIP CAPACITOR 0603 NPO ±0.25PF7P(03)1YageoYageoPA-LXT12-B002930-Jan-15 C7CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C70CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C73CHIP CAPACITOR 0402 X7R ±10%0.01UF1YageoYageo C74CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C76CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C77CHIP CAPACITOR 0402 X7R ±10%0.01UF1YageoYageo C8CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C80CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C85CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C9CHIP CAPACITOR 0603 NPO ±0.25PF10P(03)1YageoYageo C90CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C95CHIP CAPACITOR 0402 NPO ±5%100P1YageoYageo C98CHIP CAPACITOR 0402 Y5V0.1UF1YageoYageo C998CHIP CAPACITOR 0402 NPO ±0.25PF2P1YageoYageo C999CHIP CAPACITOR 0805 X5R ±10%10UF/10V (05)1MurataASKO CMIC1Condensor MicF9745AP342-98 (RoHS)1InnovationInnovation Remark1st Vendor ECO Ref.NoQ'tyManufacturerDescriptionItems Global Link Corporation Confidential Proprietary page1/3 GLOBAL LINK CORP. LTD. LXT535PA Series - Bill of Material Dwg. No. : LXT535PA-BOM-M-05 Rev. Date: 11/06/15 Remark1st Vendor ECO Ref.NoQ'tyManufacturerDescriptionItems CPU1 IC CPU (Flash)WT56F108 1WeltrendGL buy & sell D1Chip Diode SwitchingKDS114E1KECEon D13Chip Diode SwitchingKDS114E1KECEon D2Chip Diode SwitchingKDS114E1KECEon D3SMT Schottky Barrier Diode DiodeSM130A1LRCLRC IC1Analog Radio ICBK48131BekenGL consign IC1012.2Vdc Detector ICME2808A22M3G1JB…

Text truncated - open the document above for the full version.

Display Default value ① Max. deviation Alignment td 0b Test frequency ; 462.5625MHz ① GMRS Squelch Alignment gr 09 Test frequency ; 462.7125MHz 5. CPU version and Memory clear by press and holding the Up button then turn on the radio. 4. Receiver Squelch Alignment 1) TP(ALG1) is short to GND. 6. If TP(ALG1) is short to GND, Alignment mode is enable. If TP(ALG1) is open to GND, Alignment mode is disable. 2) Go to RX squelch alignment mode by press and holding the Menu button then turn on the radio. 3) LCD become sequential on display such as belows. Press the Menu button to change each step. Display Default value and Press the Up or Down button to align if necessory each step. LXT535PA Alignment Procedure 2015. 08. 27. 1. VCO Alignment ; Fixed. 2. Transmitter Frequency Alignment 1) Set the unit at channel 1.(462.5625MHz) Press the PTT button so the unit will be in transmit mode. 2)Adjust CT1 trimmer until Fc +/- 200Hz. 3. Transmitter Output Power and Max. Deviation 5) Press the PTT button so the unit will be in transmit mode. 6) Adjust up/down button until 24dBm +/- 1dBm 2) Set the power supply at 4.8Vdc. Set the unit at GMRS ch 1.(462.5625MHz) 7) Set the unit on Hi power. Press the PTT button so the unit will be in transmit mode. 8) TX Hi power only cofirm the 28dBm +/- 1dBm 9) Set the unit at FRS Ch 8.(467.5625MHz) 10) Press the PTT button so the unit will be in transmit mode. 11) FRS channel power only confirm the 24dBm +/- 1dBm 1) TP(ALG1) is short to GND. ② TX Low Power Alignment Lp 03 Test frequency ; 462.5625MHz 3) Go to Max. deviation and Low Power alignment mode by press and holding the Call button then turn on the radio. 4) LCD become sequential on display such as belows. Press the Menu button to change each step. and Press the Up or Down button to align if necessory each step.

Test Lab System DUT: D Commun Medium Phantom Measure DASY4      Flat-Se Maximu Flat-Se dz=5mm Referenc Peak SA SAR(1 g Maximu boratory: KE m verificatio Dipole 450 M nication Sys m parameters m section: Fla ement Standa Configurati Probe: ES3 D Sensor-Surfa Electronics: Phantom: E L Measuremen ection_HSL um value of S ection_HSL m ce Value = 3 AR (extrapola g) = 1.2 mW um value of S ES Co., Ltd. on_450_HS MHz; Type: D tem: CW; Fr used: f = 45 at Section ard: DASY4 on: DV3 - SN331 face: 4mm (M DAE4 Sn13 LI v5.0_2013 nt SW: DAS L_450/Area SAR (interpo L_450/Zoom 37.2 V/m; Po ated) = 1.87 W/g; SAR(10 SAR (measu SL D450V3; Se requency: 45 0 MHz; σ = (High Preci 15; ConvF(6 Mechanical S 344; Calibrat 3_01_23; Ty Y4, V4.7 Bu a Scan (41x olated) = 1.20 m Scan (7x7 ower Drift = 0 W/kg g) = 0.848 m red) = 1.26 m erial: D450V 50 MHz;Duty 0.835 mho/m sion Assessm 6.91, 6.91, 6.9 Surface Detec ted: 2014-11 ype: QDOVA uild 80; Postp x201x1): Me 0 mW/g 7x7)/Cube 0.206 dB mW/g mW/g Date V3 - SN:1081 y Cycle: 1:1 m; ε r = 43.7; ment) 91); Calibrat ction) -12 A002AA; Ser processing S easurement g 0: Measurem e/Time: 2015 1 ρ = 1000 k g ted: 2015-05 rial: TP:1190 W: SEMCA grid: dx=15m ment grid: dx 5-08-31 AM g/m 3 -27 0 AD, V1.8 Bui mm, dy=15m x=5mm, dy= 11:20:11 ild 186 mm =5mm, Test Lab System DUT: D Commun Medium Phantom Measure DASY4      Flat-Se Maximu Flat-Se dz=5mm Referenc Peak SA SAR(1 g Maximu boratory: KE m verificatio Dipole 450 M nication Sys m parameters m section: Fla ement Standa Configurati Probe: ES3DV Sensor-Surface Electronics: DA Phantom: ELI v Measurement S ection_MSL um value of S ection_MSL m ce Value = 3 AR (extrapola g) = 1.03 mW um value of S ES Co., Ltd. on_450_MS MHz; Type: D tem: CW; Fr used: f = 45 at Section ard: DASY4 on: V3 - SN3315; Co e: 4mm (Mecha AE4 Sn1344; C v5.0_2013_01_ SW: DASY4, V L_450/Area SAR (interpo L_450/Zoom 34.3 V/m; Po ated) = 1.56 W/g; SAR(1 SAR (measu SL D450V3; Se requency: 45 0 MHz; σ = (High Preci onvF(6.99, 6.99 anical Surface D Calibrated: 2014 _23; Type: QDO V4.7 Build 80; P a Scan (41x olated) = 1.0 m Scan (7x ower Drift = 0 W/kg 0 g) = 0.701 red) = 1.10 m erial: D450V 50 MHz;Duty 0.899 mho/m sion Assessm 9, 6.99); Calibr Detection) 4-11-12 OVA002AA; Se Postprocessing x201x1): M 9 mW/g x7x7)/Cube 0.048 dB mW/g mW/g Da V3 - SN:1081 y Cycle: 1:1 m; ε r = 55.2; ment) ated: 2015-05-2 erial: TP:1190 SW: SEMCA D easurement g 0: Measure ate/Time: 201 1 ρ = 1000 k g 27 D, V1.8 Build 18 grid: dx=15m ment grid: dx 15-08-31 PM g/m 3 86 mm, dy=15m dx=5mm, dy= M 3:05:50 mm =5mm, Plot 1 Test Lab Face_G DUT: L Commun Medium kg/m 3 Phanto m Measure DASY4      Face_G dx=15m Info: In t Maximu Face_G grid: dx= Referenc Peak SA SAR(1 g Info: In t Maximu boratory: KE GMRS_Ana LXT535PA; nication Sys m parameters m section: Fla ement Standa Configurati Probe: ES3DV Sensor-Surface Electronics: DA Phantom: ELI v Measurement S GMRS_Ana mm, dy=15mm terpolated me um value of S GMRS_Ana =5mm, dy=5 ce Value = 3 AR (extrapola g) = 0.724 m terpolated me um value of S ES Co., Ltd. alog_25mm Type: Bar; tem: CW; F r used (interp at Section ard: DASY4 on: V3 - SN3315; Co e: 4mm (Mecha AE4 Sn1344; C v5.0_2013_01_ SW: DASY4, V alog_25mm m edium param SAR (interpo alog_25mm 5mm, dz=5m 30.8 V/m; Po ated) = 0.969 mW/g; SAR( edium param SAR (measu m Gap_462. Serial: N/A requency: 46 olated): f = 4 (High Preci onvF(6.91, 6.91 anical Surface D Calibrated: 2014 _23; Type: QDO V4.7 Build 80; P m Gap_462. meters used fo olated) = 0.77 m Gap_462. mm ower Drift = 0 9 W/kg 10 g) = 0.56 meters used fo red) = 0.749 .7250 A 62.725 MHz; 462.725 MH sion Assessm 1, 6.91); Calibr Detection) 4-11-12 OVA002AA; Se Postprocessing .7250/Area for SAR eval 78 mW/g .7250/Zoom 0.022 dB 66 mW/g for SAR eval 9 mW/g Da ;Duty Cycle: Hz; σ = 0.857 ment) ated: 2015-05-2 erial: TP:1190 SW: SEMCA D a Scan (51x luation. m Scan (7x7 luation. ate/Time: 201 1:1 mho/m; ε r = 27 D, V1.8 Build 18 121x1): Me 7x7)/Cube 15-08-31 PM = 43.4; ρ = 10 86 easurement g 0: Measurem M 1:13:34 000 grid: ment Plot 2 Test Lab Face_F DUT: L Commun Medium kg/m 3 Phanto m Measure DASY4      Face_F dx=15m Info: In t Maximu Face_F dx=5mm Referenc Peak SA SAR(1 g Info: In t Maximu boratory: KE FRS_Analo LXT535PA; nication Sys m parameters m section: Fla ement Standa Configurati Probe: ES3DV Sensor-Surface Electronics: DA Phantom: ELI v Measurement S FRS_Analo mm, dy=15mm terpolated me um value of S FRS_Analo m, dy=5mm, ce Value = 2 AR (extrapola g) = 0.352 m terpolated me um value of S ES Co., Ltd. g_25mm G Type: Bar; tem: CW; F r used (interp at Section ard: DASY4 on: V3 - SN3315; Co e: 4mm (Mecha AE4 Sn1344; C v5.0_2013_01_ SW: DASY4, V g_25mm G m edium param SAR (interpo g_25mm G dz=5mm 20.0 V/m; Po ated) = 0.477 mW/g; SAR( edium param SAR (measu Gap_467.71 Serial: N/A requency: 46 olated): f = 4 (High Preci onvF(6.91, 6.91 anical Surface D Calibrated: 2014 _23; Type: QDO V4.7 Build 80; P Gap_467.71 meters used fo olated) = 0.3 Gap_467.71 ower Drift = 0 7 W/kg 10 g) = 0.27 meters used fo red) = 0.367 25 A 67.712 MHz; 467.712 MH sion Assessm 1, 6.91); Calibr Detection) 4-11-12 OVA002AA; Se Postprocessing 25/Area Sc for SAR eval 60 mW/g 25/Zoom S 0.047 dB 75 mW/g for SAR eval 7 mW/g Date ;Duty Cycle: Hz; σ = 0.862 ment) ated: 2015-05-2 erial: TP:1190 SW: SEMCA D can (51x121 luation. Scan (7x7x7 luation. e/Time: 2015 1:1 mho/m; ε r = 27 D, V1.8 Build 18 1x1): Measu 7)/Cube 0: M 5-08-31 PM = 43.4; ρ = 10 86 urement grid Measuremen 12:23:43 000 d: nt grid: Plot 3 Test Lab Body_G DUT: L Commun Medium kg/m 3 Phanto m Measure DASY4      Body_G dx=15m Info: In t Maximu Body_G dx=5mm Referenc Peak SA SAR(1 g Info: In t Maximu boratory: KE GMRS_An LXT535PA; nication Sys m parameters m section: Fla ement Standa Configurati Probe: ES3DV Sensor-Surface Electronics: DA Phantom: ELI v Measurement S GMRS_An mm, dy=15mm terpolated me um value of S GMRS_An m, dy=5mm, ce Value = 3 AR (extrapola g) = 1.01 mW terpolated me um value of S …

Text truncated - open the document above for the full version.

KES Co., Ltd. C-3701, Simin-daero 365-40, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-SR-15T0026 Page (2 ) of (20) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The test results in the report only apply to the tested sample. KES-P-5101-14 Rev. 1 KES A4 Revision history Revision Date of issue Test report No. Description - 2015.09.04 KES-SR-15T0026Initial KES Co., Ltd. C-3701, Simin-daero 365-40, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-SR-15T0026 Page (3 ) of (20) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The test results in the report only apply to the tested sample. KES-P-5101-14 Rev. 1 KES A4 TABLE OF CONTENTS 1. General information ................................................................................................................................................... 4 1.1. EUT description ........................................................................................................................................ 4 1.2. Short description of the equipment under test(EUT) ................................................................................. 4 1.3. Highest SAR summary .............................................................................................................................. 4 1.4. Guidance applied ....................................................................................................................................... 5 1.5. Test conditions ........................................................................................................................................... 5 1.6. SAR definition ........................................................................................................................................... 5 1.7. Accessories of EUT ................................................................................................................................... 6 2. SAR measurement system .......................................................................................................................................... 7 2.1. Robot ......................................................................................................................................................... 8 2.2. Probe ......................................................................................................................................................... 8 2.3. Data Acquisition Electronics (DAE) ......................................................................................................... 9 2.4. Phantoms ................................................................................................................................................... 9 2.5. Device holder .......................................................................................................................................... 10 3. SAR measurement procedure ................................................................................................................................... 11 4. Tissue simulating liquids .......................................................................................................................................... 13 5. System verification ................................................................................................................................................... 14 5.1. Procedure ................................................................................................................................................. 14 5.2. System verification .................................................................................................................................. 14 6. RF exposure limits ................................................................................................................................................... 15 7. Test results summary ................................................................................................................................................ 16 7.1. RF conducted power ................................................................................................................................ 16 7.1.1. Power measurement procedures ...................................................................................................... 16 7.1.2. RF conducted power ....................................................................................................................... 16 7.1.2. Target power and Tune-up limits .................................................................................................... 16 7.2. SAR results .............................................................................................................................................. 17 7.2.1. SAR measurement results ............................................................................................................... 17 8. Measurement equipments ......................................................................................................................................... 18 9. Measurement Uncertainty ........................................................................................................................................ 19 Appendix list..................................................................................................................................................................... 20 Appendix A. DASY4 report ...................................................................................................................................... 20 Appendix B. Calibration certificate ....................................................................…

Text truncated - open the document above for the full version.

KES Co., Ltd. C-3701, Simin-daero 365-40, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-15T0067 Page (2 ) of (32) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The test results in the report only apply to the tested sample. KES-P-5101-14 Rev. 1 KES A4 Revision history Revision Date of issue Test report No. Description - 2015.09.07 KES-RF-15T0067Initial KES Co., Ltd. C-3701, Simin-daero 365-40, Dongan-gu, Anyang-si, Gyeonggi-do, 14057, Korea Tel: +82-31-425-6200 / Fax: +82-31-424-0450 www.kes.co.kr Test report No.: KES-RF-15T0067 Page (3 ) of (32) This report shall not be reproduced except in full, without the written approval of KES Co., Ltd. The test results in the report only apply to the tested sample. KES-P-5101-14 Rev. 1 KES A4 TABLE OF CONTENTS 1. General information ................................................................................................................................... 4 1.1. EUT description ......................................................................................................................... 4 1.2. Test configuration ....................................................................................................................... 4 1.3. Frequency/channel operations .................................................................................................... 5 1.4. Information about derivative model ........................................................................................... 5 1.5. Device modifications .............................................................................................…

Text truncated - open the document above for the full version.