MMURTI0300Remote Control Transmitter

IR-PROProfessional Infrared Code Capture System T3Universal System Controller T3 Operation Guide v1.0 i FEDERAL COMMUNICATIONS COMMISSION NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: MMURTI0300 CAN: 3166-RTI0300 T3 Universal System Controller ii BATTERY DISPOSAL For environmental reasons, your T3 universal system controller uses “environmentally sound” Lithium-ion rechargeable batteries. These batteries do not contain any poisonous heavy metals that can damage the environment. In the interest of recycling, please do not dispose of these batteries in the household waste at the end of their useful life. Instead, dispose of them at an appropriate collection site. SAFETY SUGGESTIONS Read Instructions. Read all safety and operating instructions before operating the unit. Heat. Keep the unit away from heat sources such as radiators, heat registers, stoves, etc., including amplifiers that produce heat. Power Sources. Connect the docking station only to the power supply that was included with the unit. Recharge the battery only with the docking station that was included with the unit. Power Cord Protection. Route power supply cords so that they are not likely to be walked on or pinched by items placed on or against them, paying particular attention to the cords at power receptacles and at the point at which they exit from the unit. Nonuse Periods. Unplug the power supply from the outlet when the unit is to be left unused for a long period. Water and Moisture. Do not use the unit near water—for example, near a sink, in a wet basement, near a swimming pool, near an open window, etc. Object and Liquid Entry. Do not allow objects to fall or liquids to be spilled into the enclosure through openings. Cleaning. The unit should be cleaned only as recommended in the operating guide. Li-ion iii Servicing. Do not attempt any service beyond that described in the operating guide. Refer all other service needs to qualified service personnel. Damage Requiring Service. The unit should be serviced by qualified service personnel when: • The power supply cord or the plug has been damaged. • Objects have fallen or liquid has been spilled into the unit. • The unit does not appear to operate normally or exhibits a marked change in performance. LIMITED WARRANTY Remote Technologies Incorporated warrants its products for a period of one (1) year from the date of purchase from Remote Technologies Incorporated or an authorized Remote Technologies Incorporated distributor. This warranty may be enforced by the original purchaser and subsequent owners during the warranty period, so long as the original dated sales receipt or other proof of warranty coverage is presented when warranty service is required. Except as specified below, this warranty covers all defects in material and workmanship in this product. The following are not covered by the warranty: Damage resulting from: 1. Accident, misuse, abuse, or neglect. 2. Failure to follow instructions contained in this Guide. 3. Repair or attempted repair by anyone other than Remote Technologies Incorporated. 4. Causes other than product defects, including lack of skill, competence or experience of user. 5. Shipment of this product (claims must be made to carrier). 6. Being altered or which the serial number has been defaced, modified or removed. T3 Universal System Controller iv Remote Technologies Incorporated is not liable for any damages caused by its products or for its failure of its products to perform, including any lost profits, lost savings, incidental damages, or consequential damages. Remote Technologies Incorporated is not liable for damages based upon inconvenience, loss of use of the product, loss of time, interrupted operation, commercial loss, any claim made by a third party or made by you for a third party. Remote Technologies Incorporated’s liability for any defective product is limited to repair or replacement of the product, at our option. If your T3 needs service, please contact Remote Technologies Incorporated by telephone, fax or e-mail for return information. Please do not return products to RTI without return authorization. DISCLAIMER All rights are reserved. No part of this document may be photocopied, reproduced, or translated without the prior written notice of Remote Technologies Incorporated. The information contained in this document is subject to change without notice. Remote Technologies Incorporated shall not be liable for errors or omissions contained herein or for consequential damages in connection with the furnishing, performance, or use of this guide. Microsoft and Windows are registered trademarks of Microsoft Corporation. Other brands and t…

Text truncated - open the document above for the full version.

IR-PROProfessional Infrared Code Capture System T3Universal System Controller T3 Operation Guide v1.0 i FEDERAL COMMUNICATIONS COMMISSION NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: MMURTI0300 CAN: 3166-RTI0300 T3 Universal System Controller ii BATTERY DISPOSAL For environmental reasons, your T3 universal system controller uses “environmentally sound” Lithium-ion rechargeable batteries. These batteries do not contain any poisonous heavy metals that can damage the environment. In the interest of recycling, please do not dispose of these batteries in the household waste at the end of their useful life. Instead, dispose of them at an appropriate collection site. SAFETY SUGGESTIONS Read Instructions. Read all safety and operating instructions before operating the unit. Heat. Keep the unit away from heat sources such as radiators, heat registers, stoves, etc., including amplifiers that produce heat. Power Sources. Connect the docking station only to the power supply that was included with the unit. Recharge the battery only with the docking station that was included with the unit. Power Cord Protection. Route power supply cords so that they are not likely to be walked on or pinched by items placed on or against them, paying particular attention to the cords at power receptacles and at the point at which they exit from the unit. Nonuse Periods. Unplug the power supply from the outlet when the unit is to be left unused for a long period. Water and Moisture. Do not use the unit near water—for example, near a sink, in a wet basement, near a swimming pool, near an open window, etc. Object and Liquid Entry. Do not allow objects to fall or liquids to be spilled into the enclosure through openings. Cleaning. The unit should be cleaned only as recommended in the operating guide. Li-ion iii Servicing. Do not attempt any service beyond that described in the operating guide. Refer all other service needs to qualified service personnel. Damage Requiring Service. The unit should be serviced by qualified service personnel when: • The power supply cord or the plug has been damaged. • Objects have fallen or liquid has been spilled into the unit. • The unit does not appear to operate normally or exhibits a marked change in performance. LIMITED WARRANTY Remote Technologies Incorporated warrants its products for a period of one (1) year from the date of purchase from Remote Technologies Incorporated or an authorized Remote Technologies Incorporated distributor. This warranty may be enforced by the original purchaser and subsequent owners during the warranty period, so long as the original dated sales receipt or other proof of warranty coverage is presented when warranty service is required. Except as specified below, this warranty covers all defects in material and workmanship in this product. The following are not covered by the warranty: Damage resulting from: 1. Accident, misuse, abuse, or neglect. 2. Failure to follow instructions contained in this Guide. 3. Repair or attempted repair by anyone other than Remote Technologies Incorporated. 4. Causes other than product defects, including lack of skill, competence or experience of user. 5. Shipment of this product (claims must be made to carrier). 6. Being altered or which the serial number has been defaced, modified or removed. T3 Universal System Controller iv Remote Technologies Incorporated is not liable for any damages caused by its products or for its failure of its products to perform, including any lost profits, lost savings, incidental damages, or consequential damages. Remote Technologies Incorporated is not liable for damages based upon inconvenience, loss of use of the product, loss of time, interrupted operation, commercial loss, any claim made by a third party or made by you for a third party. Remote Technologies Incorporated’s liability for any defective product is limited to repair or replacement of the product, at our option. If your T3 needs service, please contact Remote Technologies Incorporated by telephone, fax or e-mail for return information. Please do not return products to RTI without return authorization. DISCLAIMER All rights are reserved. No part of this document may be photocopied, reproduced, or translated without the prior written notice of Remote Technologies Incorporated. The information contained in this document is subject to change without notice. Remote Technologies Incorporated shall not be liable for errors or omissions contained herein or for consequential damages in connection with the furnishing, performance, or use of this guide. Microsoft and Windows are registered trademarks of Microsoft Corporation. Other brands and t…

Text truncated - open the document above for the full version.

300-5000 BPS Remote Technologies Incorporated TheaterTouch System Controlle r RF Block/Signal Diagram 01-28-2000 Vcc Data In SAW Oscillato r RF Amplifie r Output Isolation and Filte r Keyed Output 50 Ohm RF Out (Ant.) 433 MHz

Keypad Battery LCD Power Supply Voltage Regulators (Backlights) CPU Power Supply MCU (C8051F311) PXA255 3.6864Mhz Crystal Flash SDRAM Codec & Speaker RF Dau g hterboard Remote Technologies Incorporated TheaterTouch T3 System Controlle r Block/Signal Diagram 433 MHz Linx RF Transmitte r 433Mhz Linx Splatch Antenna LCD Display

300-5000 BPS Remote Technologies Incorporated TheaterTouch System Controlle r RF Block/Signal Diagram 01-28-2000 Vcc Data In SAW Oscillato r RF Amplifie r Output Isolation and Filte r Keyed Output 50 Ohm RF Out (Ant.) 433 MHz

Keypad Battery LCD Power Supply Voltage Regulators (Backlights) CPU Power Supply MCU (C8051F311) PXA255 3.6864Mhz Crystal Flash SDRAM Codec & Speaker RF Dau g hterboard Remote Technologies Incorporated TheaterTouch T3 System Controlle r Block/Signal Diagram 433 MHz Linx RF Transmitte r 433Mhz Linx Splatch Antenna LCD Display

D C B A 4321 D C B A 4321 PAGE 1 OF 1 TITLE PRODUCT ID LABEL .. REMOTE TECHNOLOGIES INC. CHANHASSEN, MN 55317 PART NO.DOCUMENT NOREV.SIZE C This is an unpublished work containing Remote Technologies Inc. confidential and proprietary information. Disclosure, use or reproduction without the written authorization of Remote Technologies Inc. is strictly prohibited. MODEL APPROVALSDATE DFTG CHKD MFG APPVL REVISION RECORD REVDESCRIPTIONDATEDRAFT FINISH MATERIAL MM (INCH) 25.4MM = 1 INCH TOLERANCES EXCEPT AS NOTED INCHES .0 } 0.1 .00 } 0.01 .000 } 0.015 DO NOT SCALE DRAWING NOTES A1 Initial Release01/11/05 1. MATERIAL: IDENTCO TT705, GLOSSY WHITE, SYNTHETIC .003" THICK, THERMAL TRANSFER FILM. ADHESIVE TO BE .001" THICK PERMANENT ACRYLIC PRESSURE SENSITIVE ADHESIVE, WITH A 50 LB. RELEASE LINER. BACKGROUND COLOR TO BE BLACK. 2. VENDOR TO SUBMIT FIRST PIECE SAMPLE(S) FOR APPROVAL OF DIE-CUTS, THERMAL TRANSFER AND COLOR PRIOR TO PRODUCTION. 3. GRAPHICS TO BE DIRECT READING FROM FRONT SIDE OF PIECE. 4. PRINTING TO BE OF SUFFICIENT GRADE TO PREVENT ANY DEGRADATION, BLURRING, OR "SAWTOOTHING" OF LEGENDS WHEN VIEWED AT A DISTANCE OF 18". MATERIAL SEQUENCE - MATTE FINISH - COLOR (BLACK) - GLOSSY WHITE POLYESTER .003" - PERMANENT ACRYLIC ADHESIVE .001" - RELEASE LINER JMD T3 A1 01/11/05 JMD Made in Taiwan 1.00 [25.40mm] 0.35 [8.90mm] 40-210231-13 40-210231-10-14 SERIAL NUMBERS SERIAL NUMBERS = 070-XXXXXX START AT 005000 (five thousand) AND INCREMENT. INCREMENT EACH LABEL BY 1 (one) i.e. 070-005001, 070-005002, 070-005003,....... 070 = PRODUCT CODE XXXXXX = SEQUENTIAL SERIAL NUMBER P/N 20-210040-09 FCC ID: MMURTI0300 S/N For Home or Office Use IC: 3166-RTI0300

D C B A 4321 D C B A 4321 PAGE 1 OF 1 TITLE PRODUCT ID LABEL .. REMOTE TECHNOLOGIES INC. CHANHASSEN, MN 55317 PART NO.DOCUMENT NOREV.SIZE C This is an unpublished work containing Remote Technologies Inc. confidential and proprietary information. Disclosure, use or reproduction without the written authorization of Remote Technologies Inc. is strictly prohibited. MODEL APPROVALSDATE DFTG CHKD MFG APPVL REVISION RECORD REVDESCRIPTIONDATEDRAFT FINISH MATERIAL MM (INCH) 25.4MM = 1 INCH TOLERANCES EXCEPT AS NOTED INCHES .0 } 0.1 .00 } 0.01 .000 } 0.015 DO NOT SCALE DRAWING NOTES A1 Initial Release01/11/05 1. MATERIAL: IDENTCO TT705, GLOSSY WHITE, SYNTHETIC .003" THICK, THERMAL TRANSFER FILM. ADHESIVE TO BE .001" THICK PERMANENT ACRYLIC PRESSURE SENSITIVE ADHESIVE, WITH A 50 LB. RELEASE LINER. BACKGROUND COLOR TO BE BLACK. 2. VENDOR TO SUBMIT FIRST PIECE SAMPLE(S) FOR APPROVAL OF DIE-CUTS, THERMAL TRANSFER AND COLOR PRIOR TO PRODUCTION. 3. GRAPHICS TO BE DIRECT READING FROM FRONT SIDE OF PIECE. 4. PRINTING TO BE OF SUFFICIENT GRADE TO PREVENT ANY DEGRADATION, BLURRING, OR "SAWTOOTHING" OF LEGENDS WHEN VIEWED AT A DISTANCE OF 18". MATERIAL SEQUENCE - MATTE FINISH - COLOR (BLACK) - GLOSSY WHITE POLYESTER .003" - PERMANENT ACRYLIC ADHESIVE .001" - RELEASE LINER JMD T3 A1 01/11/05 JMD Made in Taiwan 1.00 [25.40mm] 0.35 [8.90mm] 40-210231-13 40-210231-10-14 SERIAL NUMBERS SERIAL NUMBERS = 070-XXXXXX START AT 005000 (five thousand) AND INCREMENT. INCREMENT EACH LABEL BY 1 (one) i.e. 070-005001, 070-005002, 070-005003,....... 070 = PRODUCT CODE XXXXXX = SEQUENTIAL SERIAL NUMBER P/N 20-210040-09 FCC ID: MMURTI0300 S/N For Home or Office Use IC: 3166-RTI0300

IR-PROProfessional Infrared Code Capture System T3Universal System Controller T3 Operation Guide v1.0 i FEDERAL COMMUNICATIONS COMMISSION NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: MMURTI0300 CAN: 3166-RTI0300 T3 Universal System Controller ii BATTERY DISPOSAL For environmental reasons, your T3 universal system controller uses “environmentally sound” Lithium-ion rechargeable batteries. These batteries do not contain any poisonous heavy metals that can damage the environment. In the interest of recycling, please do not dispose of these batteries in the household waste at the end of their useful life. Instead, dispose of them at an appropriate collection site. SAFETY SUGGESTIONS Read Instructions. Read all safety and operating instructions before operating the unit. Heat. Keep the unit away from heat sources such as radiators, heat registers, stoves, etc., including amplifiers that produce heat. Power Sources. Connect the docking station only to the power supply that was included with the unit. Recharge the battery only with the docking station that was included with the unit. Power Cord Protection. Route power supply cords so that they are not likely to be walked on or pinched by items placed on or against them, paying particular attention to the cords at power receptacles and at the point at which they exit from the unit. Nonuse Periods. Unplug the power supply from the outlet when the unit is to be left unused for a long period. Water and Moisture. Do not use the unit near water—for example, near a sink, in a wet basement, near a swimming pool, near an open window, etc. Object and Liquid Entry. Do not allow objects to fall or liquids to be spilled into the enclosure through openings. Cleaning. The unit should be cleaned only as recommended in the operating guide. Li-ion iii Servicing. Do not attempt any service beyond that described in the operating guide. Refer all other service needs to qualified service personnel. Damage Requiring Service. The unit should be serviced by qualified service personnel when: • The power supply cord or the plug has been damaged. • Objects have fallen or liquid has been spilled into the unit. • The unit does not appear to operate normally or exhibits a marked change in performance. LIMITED WARRANTY Remote Technologies Incorporated warrants its products for a period of one (1) year from the date of purchase from Remote Technologies Incorporated or an authorized Remote Technologies Incorporated distributor. This warranty may be enforced by the original purchaser and subsequent owners during the warranty period, so long as the original dated sales receipt or other proof of warranty coverage is presented when warranty service is required. Except as specified below, this warranty covers all defects in material and workmanship in this product. The following are not covered by the warranty: Damage resulting from: 1. Accident, misuse, abuse, or neglect. 2. Failure to follow instructions contained in this Guide. 3. Repair or attempted repair by anyone other than Remote Technologies Incorporated. 4. Causes other than product defects, including lack of skill, competence or experience of user. 5. Shipment of this product (claims must be made to carrier). 6. Being altered or which the serial number has been defaced, modified or removed. T3 Universal System Controller iv Remote Technologies Incorporated is not liable for any damages caused by its products or for its failure of its products to perform, including any lost profits, lost savings, incidental damages, or consequential damages. Remote Technologies Incorporated is not liable for damages based upon inconvenience, loss of use of the product, loss of time, interrupted operation, commercial loss, any claim made by a third party or made by you for a third party. Remote Technologies Incorporated’s liability for any defective product is limited to repair or replacement of the product, at our option. If your T3 needs service, please contact Remote Technologies Incorporated by telephone, fax or e-mail for return information. Please do not return products to RTI without return authorization. DISCLAIMER All rights are reserved. No part of this document may be photocopied, reproduced, or translated without the prior written notice of Remote Technologies Incorporated. The information contained in this document is subject to change without notice. Remote Technologies Incorporated shall not be liable for errors or omissions contained herein or for consequential damages in connection with the furnishing, performance, or use of this guide. Microsoft and Windows are registered trademarks of Microsoft Corporation. Other brands and t…

Text truncated - open the document above for the full version.

Remote Technologies Incorporated •7630 Executive Dr. • Eden Prairie, MN 55344 • Tel. 612.937.2600 • Fax 612.937.7527 Universal System Controller Operational Description Purpose of the TheaterTouch The intended use of the Universal System Controller is to transmit IR, (infrared) control signals to home electronic devices. These devices include VCRs, DVD players, TV cable boxes, audio surround decoders, satellite receivers, televisions, etc. The Universal System Controller is a custom programmable device that contains a touchscreen display and keypad buttons. The Touchscreen display and keypad are programmed with the users set of electronic equipment and the parameters that can be controlled. The user interface on the touchscreen display is also custom programmable. The Universal System Controller is then programmed with the IR controls for each electronic device that the user desires to use. Universal System Controller Transmitter When the user interface for the electronic devices to be controlled and the IR control signals have been programmed into the Universal System Controller it is ready to use. When a user presses on the touchscreen or keypad to transmit, for example to start the play control on a VCR, the microprocessor, PXA255, senses the push. The PXA sends a serial command to the C8051F311 microcontroller. The IR control signal corresponding to that location on the touchscreen or keypad is then pulled from internal FLASH memory. When the IR control signal is identified, the control signal is routed to the RF transmitter board. The control signal is modulated on the RF transmitter board and output. The PXA255 microprocessor uses an internal PLL running at 200 MHz which is fed from an external 3.6864 crystal. The microcontroller uses an internal 24.5 MHz oscillator. The RF module uses an internal 433MHz SAW oscillator. TheaterTouch Antenna The antenna on the Universal System Controller is a grounded line SMD Planar (Splatch), soldered to the RF module, internal to the chassis and is not easily accessible.

55 44 33 22 11 D D C C B B A A A1 RELEASE FOR PROTOTYPE T3 Remote Control Schematics 1 Cover Sheet 2 Processor3 SDRAM & Flash 4 Audio, Touc hscreen & LCD 5 CIR, RF, Tilt, USB & Keypad 6 Power Supplies Page Desc ription Cover Sheet PJW 06/03/04 RELEASE FOR PROTOTYPE 06/25/04 PJW A2B1 RELEASE FOR PRODUCTION PJW 10/01/04 Rev Description ECO Appr Date B1 T3 MAIN PWB Remote Technologies Inc.18681 Lake Drive EastChanhassen, MN. 55317-9383 C 16 Friday, October 01, 2004 PJW 30-210097-20-24 TitleSize Document Number Rev Date: Drawn By Sheet of 5 5 4 4 3 3 2 2 1 1 DD CC BB AA RELEASE FOR PROTOTYPEPJWA1 5/10/04 NOTE: Trace to antenna should be as wide (up to .110") and as short as possible. No Pop RF Transmitter - Lynx Remote Technologies Inc. Wednesday, December 15, 2004 11 C 18681 Lake Drive East Chanhassen, MN. 55317-9383 A1 30-210104-20-13 TXB-433 Paul Weichelt12-15-04 Size Scale CAGE CodeDWG NORev Sheet of Date Date Date Date Model Title DFTG CHKD MFG APPVL Page Modify Date THIS IS AN UNPUBLISHED WORK CONTAINING REMOTE TECHNOLOGIES INCORPORATED CONFIDENTIAL AND PROPRIETARY INFORMATION. DISCLOSURE, USE OR REPRODUCTION WITHOUT THE WRITTEN AUTHORIZATION OF REMOTE TECHNOLOGIES IS STRICTLY PROHIBITED. RevDescriptionECOApprDate VCCVCCVCCVCC R6 0 R1 56K ANT1 433MHz Linx Tech. ANT-433-SP U2 NC7SZ14P5 24 5 3 R3 0 R4 0 C1 0.1 uF R5 TBD U1 433MHz Linx Tech. TXM-433-LC 1 2 3 45 6 7 8 GND DATA IN GND IADJ/GNDRF OUT GND VCC GND R2 0 J1 CON11 1 2 3 4 5 6 7 8 9 10 11 55 44 33 22 11 D D C C B B A A Place close to ball J15 Config ID = 0000Bit0Bit1Bit2Bit3 Processor For VCC Pins For VCCN Pins For VCCQ Pins B1 T3 MAIN PWB Remote Technologies Inc.18681 Lake Drive EastChanhassen, MN. 55317-9383 C 26 Friday, October 01, 2004 PJW 30-210097-20-24 TitleSize Document Number Rev Date: Drawn By Sheet of MD29 MA18 MA16 MA12 LCD_D7 MD31 MD24 MD19 MD9 MA11 MA0 LCD_D0 MD25 MD23 MD21 MD15 MD7 MA14 LCD_D6 MD26 MD4 LCD_D13 LCD_D4 MD27 MA20 LCD_D14 MD13 MD12 MD10 MD5 MD2 LCD_D15 LCD_D8 MD14 MD6 MA2 LCD_D10 MD18 MA9 LCD_D9 LCD_D2 MA0 MA22 MA4 MA3 LCD_D11 MA25 MA23 MA19 MA17 MA1 LCD_D5 MD28 MD0 MA5 MD8 MA7 LCD_D12 MD1 MA13 LCD_D3 MD30 MD20 MD16 MA10 MA8 LCD_D1 MD22 MD17 MD11 MA25 MA24 MA21 MA6 MD3 MA15 MMCCS0MMCCLKSD_IRQSD_CDSD_WPMMCDATMMCCMD MD[31:0] 3 nRESET 6 nTRST 6 TDI 6 TCK 6 nUSB_CONNECTED 5 TMS 6 CIR_CTS 5 AC97_SDIN 4 TILT_SWITCH 5 IRQ_TOUCH 4 ROW4 5 ROW3 5 ROW1 5 ROW2 5 SDA 5 ALS_OUT 5 TDO 6 nRESET_OUT 3 PWR_EN 6 nCS0 3 nOE 3 nWE 3 nSDCS0 3 DQM0 3 DQM1 3 DQM2 3 DQM3 3 SDCKE1 3 SDCLK1 3 nSDRAS 3 nSDCAS 3 MA[25:0] 3 USB_P 5 USB_N 5 CIR_RST# 5 PWM_BKL 6 CIR_RTS 5 nUSB_PULLUP 5 LCD_D[15:0] 4 LCD_ENAB 4 LCD_PCLK 4 SDCLK0 3 LCD_LCLK 4 AC97_BITCLK 4AC97_SDOUT 4AC97_SYNC 4 AC97_RST# 4 PWM_LED 6 LCD_PWR 6 LCD_FCLK 4 LCD_RST# 4 COL4 5 COL1 5 COL2 5 COL3 5 AUDIO_AMP_OFF 4SCL 5 ALS_CTRL0 5 ALS_CTRL1 5 +3.3V +3.3V V_CORE V_CORE +3.3V +3.3V +3.3V+3.3V V_CORE +3.3V +3.3V +3.3V +3.3V R29 56K TP15 C90.1uF6.3V C80.1uF6.3V C70.1uF6.3V C60.1uF6.3V C50.1uF6.3V C40.1uF6.3V C110uF6.3V R5 33 TP19 TP35 TP10 R8 33 R7 33 TP34 TP29 TP33 C140.1uF6.3V C110.1uF6.3V TP38 R6 33 R2156K R10 33 R31 56K TP22 TP8 C220.1uF6.3V R30 56K L110uH R1656K C190.1uF6.3V R11 33 TP3 + C211.0uF16V TP1 R26 56K TP28 R1556K TP9 TP2 R12 33 TP4 TP24 C160.1uF6.3V R3 33 C130.1uF6.3V Y1 3.6864MHz 12 34 R20 56K TP20 R1 33 TP31 R9 33 TP32 R2256K TP13 J1 HDR-4X1 STR 1234 R18 56K Populate = No TP6 C180.1uF6.3V R1756K Populate = No R10856K R25 56K Populate = No TP7 R32 56K TP25 J11 HDR-10X1 STR 12345678910 TP26 R13 56K C150.1uF6.3V R28 56K TP30 C120.1uF6.3V TP12 Bluetooth UART I2C PCMCIA / CFControl PWM 32.678kHz Crystal AC97 / I2S Control VCCN = 2.5V or 3.3V for Memory Bus and PCMCIA Memory Control Synchronous Serial Port VCCQ = 3.3V for I/O MultiMedia Card Control JTAG General Purpose I/O Memory Data Bus Power and Reset Control Standard UART / IrDA VCC = Core Voltage (nominal 1.0V, 1.1V, or 1.3V)3.6864MHz Crystal Full Function UART Memory Address Bus USB DMA LCD Control Network SSP U1 PXA255-200 B4 B5 E8 D8 B8 A8 E7 D7 C7 B7 E6 D6 E5 A6 C5 A5 D5 A4 A3 A2 C3 B3 G1 H2 H1 H6 J6 J5 J3 J1 K1 K2 K5 K6 L1 L3 M1 M3 N3 P1 R1 P2 R3 T4 R5 P5 T5 P4 N4 M5 L5 T6 N6 T7 M6 M7 M9 T10 R9 T11 P11 N10 T12 M10 H3 H5 J4 K3 L4 M2 N1 T3 P6 R7 P7 P8 L8 P10 R11 P12 D15 G14 E14 C13C10 C6 M11 T2 T16 P3 N13N11 N9N7N5 M14 M4 K4 H4 F4 D4 A1 L9L6 K10 K8 J7 H10 G9G7 F11 H11H15H16H13H12 G16G13 F13 K15K16 L16L15 K12K13 J13 L11 K11 J15J16 G11 G12 C16 H8 H9 J8 J9 T1 C2 E2 G2 J2 L2 N2 R2 R4 R6 R8 R10 R12 R14 M15 P15 C4 C8 C11 C14 F6 G8 G10 H7 J10 J14 K7 K9 L14 F15 D14 B16 H14 F14 F12 L10 L12 L13 K14 J12 J11 G15 F7 A7 B6 N15 M12 F9 E9 D9 A9 B9 F16 E16 E15 D16 N8T8P9T9R13T13G5G4F1G6G3F2M8B1B2L7E4E3D2F5D1E1F3D3C1A13E13A14A12B11B10F10F8B13D13A15B14B15C15C9E10A10E11A16D10P13T14T15R15P14R16P16M13N16M16 B12 C12 A11 D11 N14 N12 E12 D12 MBREQ_GPIO[14] MBGNT_GPIO[13] L_FCLK_GPIO[74] L_LCLK_GPIO[75] L_PCLK_GPIO[76] L_BIAS_GPIO[77] L_DD[0]_GPIO[58] L_DD[1]_GPIO[59] L_DD[2]_GPIO[60] L_DD[3]_GPIO[61] L_DD[4]_GPIO[62] L_DD[5]_GPIO[63] L_DD[6]_GPIO[64] L_DD[7]_GPIO[65] L_DD[8]_GPIO[66] L_DD[9]_GPIO[67] L_DD[10]_GPIO[68] L_DD[11]_GPIO[69] L_DD[12]_GPIO[70] L_DD[13]_GPIO[71] L_DD[14]_GPIO[72] L_DD[15]_GPIO[73] MA[0] MA[1] MA[2] MA[3] MA[4] MA[5] MA[6] MA[7] MA[8] MA[9] MA[10] MA[11] MA[12] MA[13] MA[14] MA[15] MA[16] MA[17] MA[18] MA[19] MA[20] MA[21] MA[22] MA[23] MA[24] MA[25] MD[0] MD[1] MD[2] MD[3] MD[4] MD[5] MD[6] MD[7] MD[8] MD[9] MD[10] MD[11] MD[12] MD[13] MD[14] MD[15] MD[16] MD[17] MD[18] MD[19] MD[20] MD[21] MD[22] MD[23] MD[24] MD[25] MD[26] MD[2…

Text truncated - open the document above for the full version.