MTFSHB1000SkyHub Wireless Telematics Hub

SkyBitz SkyHub & SkyCamera Installation 1 SkyHub with SkyCamera Installation SkyHub Componets • SHB1000 SkyHub Tracking Device • SkyHub Mounting Bracket • 6, 10-32 Tamper Proof Screws • SkyHub Short Shroud • 6, 1/8 Inch sealing Blind Rivets • 3M Primer 94 Ampoule Tools Required: • Power Drill and 1/8 in Drill Bit • 5/32 Inch Pin in Hex Tamper Proof Screwdriver • Blind Rivet Tool • 50/50 Isopropyl Alcohol/Water Solution • Clean Rags • Tape Measurer SkyHub Mounting Location The SkyHub will be mounted to the exterior front wall of a Dry Van Trailer. The locations described below are recommended for optimal communications with the SkyCam. The general dimensions noted may be adjusted to avoid mounting on top of any logos or asset identification. For a Plate Nose Trailer, the SkyHub will be mounted to the front wall horizontally, about 3 inches down from the bottom of the top rail, and about 6 inches from the roadside edge with the connector on the left. For a Sheet and Post Nose Trailer, the SkyHub will be mounted to the front wall vertically, about 3 inches down from the bottom of the top rail, and about 6 inches from the roadside edge with the connector at the top. SkyBitz SkyHub & SkyCamera Installation 2 SkyHub Tracking System Installation • Use the SkyHub bracket as a template to mark the bracket location, and the 3 VHB tape locations on the wall • Prep the trailer wall for the 3 VHB tape mounting surface locations o Clean with IPA solution o Abrade lightly with Scotch-Brite pad o Clean again with IPA solution o Prime with 3M Primer 94 and wait at least 3 minutes • Remove the liner from the 3 VHB tape locations on the bracket, place the bracket onto the mounting location on the trailer wall, and firmly press it onto the wall • Use the rivet holes in the bracket as a guide and drill six 1/8-inch holes in the trailer wall • Secure the bracket to the wall with the six 1/8-Inch sealing rivets • Orient the SkyHub with the connector on the left for a horizontal install, or with the connector at the top for a vertical install, and install it on the bracket • Using a hand driver, secure the SkyHub to the bracket with four, 10-32 tamper proof screws SkyBitz SkyHub & SkyCamera Installation 3 • Fasten the Short Shroud to the SkyHub with two, 10-32 tamper proof screws SkyCamera Installation Components and Tools • SkyCamera with SkyCamera Mounting Bracket • 4, 10-32 Tamper Proof Screws and 5/32 Inch Pin in Hex Tamper Proof Screwdriver • 8, 3/16 inch stainless steel rivets • SkyCamera circular alignment tool • 1.75 inch hole saw • Heavy duty rivet tool • 50/50 Isopropyl Alcohol/Water Solution & Clean Rags • Scotch-Brite pad • 3m Primer 94 Ampoule SkyCamera Mounting Location The SkyCamera will be mounted to the roadside wall of the trailer about an inch down from the bottom of the top rail and about an inch forward of the panel seam as shown. Open the roadside door all the way to check for interference from the lock bar location. If the lock bars will hit the SkyCam, move the SkyCamera location forward until it clears the lock bars. SkyBitz SkyHub & SkyCamera Installation 4 SkyCamera Installation • Use the SkyCamera bracket as a template to mark the location of the bracket and the 1.75- inch camera hole • Drill the 1.75-inch hole for the camera and remove any burrs • Prep the VHB Tape mounting surface o Clean with IPA solution o Abrade lightly with Scotch-Brite pad o Clean again with IPA solution o Prime with 3M Primer 94 and wait at least 3 minutes • Insert the SkyCamera install tool into the hole • Remove the liner from all 4 pieces of VHB tape on the bracket • Align the camera hole in the SkyCamera Mounting Bracket with tool, ensure the bracket is vertical, and press the bracket onto the trailer wall • Remove the SkyCamera install tool • Using the bracket as a template, drill the eight 3/16-inch rivet holes in the trailer wall • Install the eight 3/16-inch rivets SkyBitz SkyHub & SkyCamera Installation 5 • Install the camera to the bracket with four 10-32 tamper proof screws • Remove the Barcode label taped to the SkyCamera and install it on the front of the trailer next to the 7-way connector FCC Compliance: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: 1. this device may not cause harmful interference, and 2. this device must accept any interference received including interference that may cause undesired operation. ISED Compliance: This device complies with Industrie Canada’s license exempt RSSs. Operation is subject to the following two conditions: 1. this device may not cause interference, and 2. this device must accept any interference received, including interference that may cause undesired operation of the device. Ce dispositif est conforme à la licence exempte de licence s’il s’agit de RSS. L’exploitation est assujettie aux deux conditions suivantes : 1. cet appareil peut ne pas causer d’interférences, et 2. ce dispositif doit accepter toute interférencereçue, y compris toute interférence qui peut provoquer un fonctionnement indésirable de l’appareil. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device meets the FCC requirements for RF exposure in public or uncontrolled environments (>20cm for MPE devices). SkyBitz SkyHub & SkyCamera Installation 6

Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21048 Date: Subject: Request for Permanent Confidentiality FCC ID: MTFSHB1000 To Whom It May Concern: In accordance with §0.457(d) and §0.459 of CFR 47, and KDB 726920, Telular Inc hereby requests permanent confidentiality for documents filed under the following exhibit types: 1. Schematic Diagram 2. Part List 3. Operational Description 4. Block Diagram These items contain detailed system and equipment description and related information about the product which Telular Inc considers to be proprietary, confidential and a custom design which otherwise would not be released to the general public. Since this design is a basis from which future technological products will evolve, Telular Inc also feels that this information would be of benefit to its competitors, and that the disclosure of the information in these exhibits would give our competitors an unfair advantage in the market. We are aware that exhibit types cover letters, attestations, label document, test reports, RF exposure information (SAR and MPE reports), cannot be requested to be classified confidential and are thus subject to publication, as will be documents of all other exhibits types for which we have not requested a confidentiality classification. Best Regards, Jerry Talen _______________________________ Signature Name: Jerry Talen Title: Director of Product Assurance Company Name: Telular Inc. Address: 3225 Cumberland Blvd SE, Suite 300, Atlanta, GA 30339

Composite picture of all sides: SHB1000

Rev DateChange Description Sheet 1 of 1 Scale None Date 6/23/2020 Drawn By: J.TalenApproved By: Rev. C Part Number: 96060601 Des. Eng. MFG. MECH DESIG. TELULAR Title LABEL, SER NO/FCCID/ICID/IMEI, SKYHUB Label Material Polyester Label Color White Permanent, Acrylic Label Adhesive UL Standard 969 Label Vendor Any Approved Label Fabricator Manufacturer Product or Part Number UL File Number 3M 7817 or 7871 MH16411 Blank, single color label from Label Vendor Ink Color is BLACK. All text and graphics printed at Contract Manufacturer needs approval prior to volume production Serial number. It is assigned at time of product manufacture. Serial number shown is an example. Barcode is automatically generated by the label design software Teklynx Codesoft 8.5 or equivalent. Code 128 Type B A 4/28/20 REL.TO RCRDS;SB331 SSSSSSSSSSSSS to be replaced with serial number of unit KKKKK to be replaced by country of manufacture MMMMMMMMMM to be replaced with model number R to be replaced by model revision number T to be replaced with type L. Mishrell Ilya Fuksman B. Ryan RLK CCCCCCCCCCCCCCC to be replaced with IMEI 2.000 2.000 B 6/23/20 UPDATE FCC ID;SB345 C 7/07/20 UPDATE NOM,IFT; SB351 FFFFFFFFFF to be replaced with IFETEL Cert. number

CCA Both Sides

Radio Frequency Exposure Evaluation Report FOR: Telular AMETEK Model Name: SHB1000 Product Description: SkyHub Wireless Telematics Hub FCC ID: MTFSHB1000 IC ID: 2175D-SHB1000 Per: CFR Part Part1 (1.1307 &1.1310), Part 2 (2.1091), FCC KDB 447498 D01 General RF Exposure Guidance v06 ISEDC RSS-102 Issue 5 Report number: EMC_TELUL-087-20001_FCC_ISED_MPE_R1 DATE: 2020-11-04 CETECOM Inc. 411 Dixon Landing Road  Milpitas, CA 95035  U.S.A. Phone: + 1 (408) 586 6200  Fax: + 1 (408) 586 6299  E-mail: [email protected]  http://www.cetecom.com CETECOM Inc. is a Delaware Corporation with Corporation number: 2905571 V5.0 2015-10-27 © Copyright by CETECOM Test Report #: EMC_TELUL-087-20001_FCC_ISED_MPE_R1 FCC ID: MTFSHB1000 Date of Report 2020-11-04 Page 2 of 8 IC ID: 2175D-SHB1000 Page 2 of 8 1 Assessment This RF Exposure evaluation report provides evidence for compliance of the below identified device with the RF Exposure limits for mobile devices as defined in FCC CFR Part 1 (1.1307 &1.1310), Part 2 (2.1091) and IC standard RSS-102 issue 5 under worst case conditions (measured or rated RF output power, antenna gain, distance towards human body, multiple transmitter information as presented by the applicant). In addition, maximum antenna gain or minimum distance towards the human body is calculated respectively, where relevant. The device meets the limits as stipulated by the above given FCC and IC rule parts based on available specifications for worst case conditions at 20cm distance to the body. Company Description Model # Telular AMETEK SkyHub Wireless Telematics Hub SHB1000 Report reviewed by: TCB Evaluator 2020-11-04 Compliance Cindy Li (Lab Manager) Date Section Name Signature Responsible for the Report: 2020-11-04 Compliance Yuchan Lu (Test Engineer) Date Section Name Signature Test Report #: EMC_TELUL-087-20001_FCC_ISED_MPE_R1 FCC ID: MTFSHB1000 Date of Report 2020-11-04 Page 3 of 8 IC ID: 2175D-SHB1000 Page 3 of 8 2 Administrative Data 2.1 Identification of the Testing Laboratory Issuing the Test Report Company Name: CETECOM Inc. Department: Compliance Street Address: 411 Dixon Landing Road City/Zip Code Milpitas, CA 95035 Country USA Telephone: +1 (408) 586 6200 Fax: +1 (408) 586 6299 Lab Manager: Cindy Li Responsible Project Leader: Cathy Palacios 2.2 Identification of the Client / Manufacturer Client’s Name: Telular AMETEK Street Address: 3225 Cumberland Blvd, Suite 300 City/Zip Code Atlanta, GA 30339 Country USA 2.3 Identification of the Manufacturer Manufacturer’s Name: Same as Client Manufacturers Address: City/Zip Code Country Test Report #: EMC_TELUL-087-20001_FCC_ISED_MPE_R1 FCC ID: MTFSHB1000 Date of Report 2020-11-04 Page 4 of 8 IC ID: 2175D-SHB1000 Page 4 of 8 3 Equipment under Assessment Marketing name: SkyHub HW Version : B SW Version : EM.00.01.1025,BM.00.01.1017,CM.00.01.1021 Hardware Version Identification Number (HVIN): SHB1000 Product Marketing Name (PMN): SkyHub Regulatory Band:  Cellular Module:  WCDMA/UMTS FDD BAND II: 1852.4 ~ 1907.6 MHz  WCDMA/UMTS FDD BAND V: 826.4 ~ 846.6 MHz  LTE BAND 2: 1852.5 ~ 1907.5 MHz  LTE BAND 4: 1710.7 ~ 1754.3 MHz  LTE BAND 5: 824.7 ~ 848.3 MHz  LTE BAND 12: 700.5 ~ 714.5 MHz  LTE BAND 13: 779.5 ~ 784.5 MHz  ISM:  Nominal band: 905 MHz – 925 MHz;  Center to center: 905 MHz (ch 0) – 925 MHz (ch 19), 20 channels  BLE:  Nominal band: 2400 MHz – 2483.5 MHz;  Center to center: 2402 MHz (ch 0) – 2480 MHz (ch 39), 40 channels Integrated Module Info:  WCDMA, LTE  Module name: LE910  Module number: LE910B1-NA1  FCC/IC ID: RI7LE910NAV2 / 5131A-LE910NAV2  BLE  Module name: BL654  Module number: 451-00001  FCC/IC ID: SQGBL654 / 3147A-BL654  ISM  Module name: EFR32  Module number: EFR32FG1P131F256GM32-C0  GPS  Module name: L86 Test Report #: EMC_TELUL-087-20001_FCC_ISED_MPE_R1 FCC ID: MTFSHB1000 Date of Report 2020-11-04 Page 5 of 8 IC ID: 2175D-SHB1000 Page 5 of 8  Module number: L86s-M3 Antenna Type:  Cellular:  Antenna maximum gain: o LTE Band 2: 4.4 dBi o LTE Band 4: 4.4 dBi o LTE Band 5: 2.6 dBi o LTE Band 12: 2.6 dBi o LTE Band 13: 2.6 dBi o WCDMA Band II: 4.4 dBi o WCDMA Band V: 2.6 dBi  ISM:  Antenna gain: 0.8 dBi  BLE:  Antenna gain: 0 dBi Maximum Conducted Output Power:  Cellular: From modular grant [Watts]:  WCDMA Band II: 0.232  WCDMA Band V: 0.229  LTE Band 2: 0.219  LTE Band 4: 0.205  LTE Band 5: 0.191  LTE Band 12: 0.193  LTE Band 13: 0.194  BLE: From modular grant [Watts]: 0.006  ISM: From measurement [Watts]: 0.095 Power Supply/ Rated Operating Voltage Range: Low 10 VDC, Nominal 12 VDC, High 30 VDC Operating Temperature Range: Low -40⁰C, Nominal 25⁰C, High 70⁰C Sample Revision: Prototype Unit; Production Unit; Pre-Production Test Report #: EMC_TELUL-087-20001_FCC_ISED_MPE_R1 FCC ID: MTFSHB1000 Date of Report 2020-11-04 Page 6 of 8 IC ID: 2175D-SHB1000 Page 6 of 8 4 RF Exposure Limits and FCC and IC Basic Rules For the specific described radio apparatus the following basic limits and rules apply for both, FCC and IC where not indicated differently. 4.1 Power Density Limits acc. to FCC 1.1310(e) / RSS-102 i5, cl. 4: FCC Frequency Range (MHz) Power density (mW/cm 2 ) Averaging time (minutes) 300 – 1500 f (MHz) /1500 30 1500 – 100000 1.0 30 IC 300 – 6000 0.02619 x f (MHz) 0.6834 6 4.2 Routine Environmental Evaluation Categorical Exclusion Limits acc. to FCC 2.1091(c) / RSS-102, cl. 2.5 (rounded to 1 decimal point): FCC operating frequency < 1.5GHz: excluded if ERP < 1.5W / 31.8dBm (EIRP: 33.9 dBm); operating frequency > 1.5GHz: excluded if ERP < 3.0W / 34.8dBm (EIRP: 36.9 dBm); IC 300MHz < = operating frequency < 6 GHz: excluded if EIRP < 0.0131 x f (MHz) 0.6834 W 4.3 RF Exposure Estimation (MPE Estimation) Having available the source based average output power and peak antenna gain or the ERP/EIRP of the specified device and for a known minimum distance of its radiating structures from the body of persons according to its use cases (at least 20cm) the power density at that distance can be…

Text truncated - open the document above for the full version.

FCC 47 CFR PART 22H and 24E RF Test Report Product Type ： LE910-NA V2 Applicant ： Telit Communications S.p.A. Address ： Viale Stazione di Prosecco 5/B, 34010 Sgonico- Trieste- Italy Trade Name ： Telit Model Number ： LE910-NA V2 Test Specification ： FCC 47 CFR PART 22H: Oct, 2014 FCC 47 CFR PART 24E: Oct, 2014 ANSI/TIA/EIA-603-C Application Purpose ： Original Receive Date ： Jun. 04, 2015 Test Period ： Jun. 10 ~ 18, 2015 Issue Date ： Aug. 03, 2015 Issue by A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 Note: This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. This document may be altered or revised by A Test Lab Techno Corp. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, or any government agencies. The test results in the report only apply to the tested sample. Report Number: 1506FR22-01 1 of 70 A Test Lab Techno Corp. Revision History Rev. Issue Date Revisions Revised By 00 Jul. 28, 2015 Initial Issue 01 Aug. 03, 2015 Revised report information. Peggy Chang Report Number: 1506FR22-01 2 of 70 A Test Lab Techno Corp. Verification of Compliance Issued Date: 08/03/2015 Product Type : LE910-NA V2 Applicant : Telit Communications S.p.A. Address : Viale Stazione di Prosecco 5/B, 34010 Sgonico- Trieste- Italy Trade Name : Telit Model Number : LE910-NA V2 EUT Rated Voltage : DC 3.4V / 3.8V / 4.2V Test Voltage : DC 3.8V Applicable Standard : FCC 47 CFR PART 22H: Oct, 2014 FCC 47 CFR PART 24E: Oct, 2014 ANSI/TIA/EIA-603-C Application Purpose : Original Test Result : Complied Performing Lab. : A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 http://www.atl-lab.com.tw/e-index.htm The above equipment was tested by A Test Lab Techno Corp. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.4: 2009 and the energy emitted by the sample tested as described in this report is in compliance with the requirements of FCC Rules Part 22H, Part 24E. The test results of this report relate only to the tested sample identified in this report. Approved By ： Reviewed By ： (Manager) (Fly Lu) (Testing Engineer) (Eric Ou Yang) Report Number: 1506FR22-01 3 of 70 A Test Lab Techno Corp. TABLE OF CONTENTS 1 General Information ....................................................................................................................................... 6 1.1. EUT Description ..................................................................................................................................... 6 1.2. Mode of Operation.................................................................................................................................. 7 1.3. EUT Exercise Software.......................................................................................................................... 7 1.4. Configuration of Test System Details ..................................................................................................... 7 1.5. Test Site Environment ............................................................................................................................ 8 1.6. Summary of Test Result ......................................................................................................................... 8 2 RF Output Power Test ................................................................................................................................... 9 2.1. Limit ........................................................................................................................................................ 9 2.2. Test Instruments ..................................................................................................................................... 9 2.3. Test Setup............................................................................................................................................... 9 2.4. Test Procedure ....................................................................................................................................... 9 2.5. Uncertainty ............................................................................................................................................. 9 2.6. Test Result............................................................................................................................................ 10 3 Effective Radiated Power / Equivalent Isotropic Radiated Power Test .................................................. 12 3.1. Limit ...................................................................................................................................................... 12 3.2. Test Instruments ................................................................................................................................... 12 3.3. Test Setup............................................................................................................................................. 12 3.4. Test Procedure ..................................................................................................................................... 12 3.5. Uncertainty ........................................................................................................................................... 12 3.6. Test Result............................................................................................................................................ 13 4 Peak to Average Ratio Test..............................…

Text truncated - open the document above for the full version.

FCC RF Test Report Product Type ： LE910-NA V2 Applicant ： Telit Communications S.p.A. Address ： Viale Stazione di Prosecco 5/B, 34010 Sgonico- Trieste- Italy Trade Name ： Telit Model Number ： LE910-NA V2 Test Specification ： FCC 47 CFR PART 22H: Oct, 2014 FCC 47 CFR PART 24E: Oct, 2014 FCC 47 CFR PART 27: Oct. 2014 ANSI/TIA/EIA-603-C Application Purpose ： Original Receive Date ： Jun. 04, 2015 Test Period ： Jun. 11 ~ Aug. 03, 2015 Issue Date ： Aug. 04, 2015 Issue by A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 Note: This report shall not be reproduced except in full, without the written approval of A Test Lab Techno Corp. This document may be altered or revised by A Test Lab Techno Corp. personnel only, and shall be noted in the revision section of the document. The client should not use it to claim product endorsement by TAF, or any government agencies. The test results in the report only apply to the tested sample. Report Number: 1506FR21-01 1 of 293 A Test Lab Techno Corp. Revision History Rev. Issue Date Revisions Revised By 00 Jul. 28, 2015 Initial Issue 01 Aug. 04, 2015 Revised report information. Snow Wang Report Number: 1506FR21-01 2 of 293 A Test Lab Techno Corp. Verification of Compliance Issued Date: 08/04/2015 Product Type : LE910-NA V2 Applicant : Telit Communications S.p.A. Address : Viale Stazione di Prosecco 5/B, 34010 Sgonico- Trieste- Italy Trade Name : Telit Model Number : LE910-NA V2 EUT Rated Voltage : DC 3.4V / 3.8V / 4.2V Test Voltage : DC 3.8V Applicable Standard : FCC 47 CFR PART 22H: Oct, 2014 FCC 47 CFR PART 24E: Oct, 2014 FCC 47 CFR PART 27: Oct. 2014 ANSI/TIA/EIA-603-C Test Result : Complied Application Purpose : Original Performing Lab. : A Test Lab Techno Corp. No. 140-1, Changan Street, Bade City, Taoyuan County 334, Taiwan R.O.C. Te l：+886-3-2710188 / Fax：+886-3-2710190 T aiwan Accreditation Foundation accreditation number: 1330 http://www.atl-lab.com.tw/e-index.htm The above equipment was tested by A Test Lab Techno Corp. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI/TIA/EIA-603-C and the energy emitted by the sample tested as described in this report is in compliance with the requirements of FCC Rules Part 27L. The test results of this report relate only to the tested sample identified in this report. Approved By ： Reviewed By ： (Manager) (Fly Lu) (Testing Engineer) (Eric Ou Yang) Report Number: 1506FR21-01 3 of 293 A Test Lab Techno Corp. TABLE OF CONTENTS 1 General Information ...................................................................................................................................... 6 1.1. EUT Description ..................................................................................................................................... 6 1.2. Mode of Operation.................................................................................................................................. 9 1.3. EUT Exercise Software........................................................................................................................ 16 1.4. Configuration of Test System Details ................................................................................................... 16 1.5. Test Site Environment .......................................................................................................................... 16 1.6. Summary of Test Result ....................................................................................................................... 17 2 Conducted Output Average Power Test ..................................................................................................... 18 2.1. Limit ...................................................................................................................................................... 18 2.2. Test Instruments ................................................................................................................................... 18 2.3. Test Setup............................................................................................................................................. 18 2.4. Test Procedure ..................................................................................................................................... 18 2.5. Uncertainty ........................................................................................................................................... 18 2.6. Test Result............................................................................................................................................ 19 3 Effective Radiated Power / Equivalent Isotropic Radiated Power Test ...................................................... 43 3.1. Limit ...................................................................................................................................................... 43 3.2. Test Instruments ................................................................................................................................... 43 3.3. Test Setup............................................................................................................................................. 43 3.4. Test Procedure ..................................................................................................................................... 45 3.5. Uncertainty ........................................................................................................................................... 45 3.6. Test Result............................................................................................................................................ 46 4 Frequency Stability Test..................…

Text truncated - open the document above for the full version.

Spectrum Analyzer Universal Radio Com. Tester EUT Attenuator Power divider 8 Conducted Spurious Emission and Radiation Emission Test 8.1. Limit The power of any emission outside a licensee's frequency block shall be attenuated below the transmitter power (P) by at least 43 +10 log 10 (P) dB. The limit of emission equal to -13dBm 8.2. Test Instruments Equipment Manufacturer Model No. Serial No. Cal. Date Remark Spectrum Analyzer Agilent E4445A MY46181986 05/14/2015 (1) Wideband Radio Communication Test R & S CMW500 103168 11/05/2014 (1) Attenuator RADIALL R41572000 0603033073 N.C.R. ----- Power divider Agilent 87302C 3239A00760 N.C.R. ----- Test Site ATL TE02 TE02 N.C.R. ----- Remark: (1) Calibration period 1 year. (2) Calibration period 2 years. Note: N.C.R. = No Calibration Request. 8.3. Setup Below 2.8GHz Report Number: 1506FR21-01 164 of 293 A Test Lab Techno Corp. Spectrum Analyzer Universal Radio Com. Tester EUT High Pass Filter Power divider Above 2.8GHz 8.4. Test Procedure a. The EUT was set up for the maximum peak power with LTE / WCDMA link data modulation. The power was measured with Spectrum Analyzer. All measurements were done at 3 channels (low, middle and high operational frequency range.). b. The conducted spurious emission used the power splitter via EUT RF power connector between simulation base station and spectrum analyzer. c. When the spectrum scanned from 10MHz to 2.5GHz (Band 7and Band 41: scanned from 10MHz to 4GHz) , it shall be connected to the band reject filter attenuated the carried frequency. The spectrum set RB=1MHz, VB=1MHz. d. When the spectrum scanned from 2.5GHz to 10 th harmonic (Band 7 and Band 41: scanned from 4GHz to 10 th harmonic), it shall be connected to the high pass filter attenuated the carried frequency. The spectrum set RB=1MHz, VB=1MHz. 8.5. Uncertainty The measurement uncertainty is evaluated as ± 2.24 dB. Report Number: 1506FR21-01 165 of 293 A Test Lab Techno Corp. 8.6. Test Graphs Conducted Emission LTE Band 2 (Channel Bandwidth: 1.4 MHz) _ QPSK 1850.7 MHz Report Number: 1506FR21-01 166 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 1.4 MHz) _ QPSK 1880.0 MHz Report Number: 1506FR21-01 167 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 1.4 MHz) _ QPSK 1909.3 MHz Report Number: 1506FR21-01 168 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 3 MHz) _ QPSK 1851.5 MHz Report Number: 1506FR21-01 169 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 3 MHz) _ QPSK 1880.0 MHz Report Number: 1506FR21-01 170 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 3 MHz) _ QPSK 1908.5 MHz Report Number: 1506FR21-01 171 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 5 MHz) _ QPSK 1852.5 MHz Report Number: 1506FR21-01 172 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 5 MHz) _ QPSK 1880.0 MHz Report Number: 1506FR21-01 173 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 5 MHz) _ QPSK 1907.5 MHz Report Number: 1506FR21-01 174 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 10 MHz) _ QPSK 1855.0 MHz Report Number: 1506FR21-01 175 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 10 MHz) _ QPSK 1880.0 MHz Report Number: 1506FR21-01 176 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 10 MHz) _ QPSK 1905.0 MHz Report Number: 1506FR21-01 177 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 15 MHz) _ QPSK 1857.5 MHz Report Number: 1506FR21-01 178 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 15 MHz) _ QPSK 1880.0 MHz Report Number: 1506FR21-01 179 of 293 A Test Lab Techno Corp. LTE Band 2 (Channel Bandwidth: 15 MHz) _ QPSK 1902.5 MHz Report Number: 1506FR21-01 180 of 293 A Test Lab Tec…

Text truncated - open the document above for the full version.