MTFSX6P200260Ccdma 800MHz Wireless Deskphone

09/13/05 Part Number 56033202 P HONECELL ® SX6P-200C CDMA Fixed Cellular Phone U SER M ANUAL QUICK CONNECTION GUIDE Phonecell SX6P-200C Fixed Cellular Phone LIST OF COMPONENTS Before installing your Phonecell ® SX6P , carefully remove the contents from the shipping carton and check for evidence of shipping damage. If damage is found, contact your Authorized Telular Distributor or shipping agent immediately. Phonecell ® SX6P Desktop Phone Spike Antenna AC Power Cube Spike Antenna Phonecell ® SX6P CDMA i User Manual SX6P MENU STRUCTURE 1. Phone Book ViewAddEditErase 3. Time/Alarm AlarmTime FormatDate Format 5. Phone Settings BannerLCD ContrastDTMF LengthKey VolumeAuto Send TimeFreq Dial NumLanguageDial Tone TypeSelftest Cycle 2. Call History MissedOutgoingIncomingErase HistoryLast Call TimeAir TimeClear Air Tim^ Menu 4. Ring/Alert Ring ToneRing Volume1 Min AlertService AlertAlarm Tone 6. Phone Info My Phone #VersionTech Mode 7. Security Change CodeRestrictVoice PrivacyLock ModeReset PhoneHot LineRUIM CHV1 (RUIM Models Only) 8. Programming Phonecell ® SX6P CDMA ii User Manual SAFE OPERA TION INSTRUCTIONS IMPORTANT! Before installing or operating this product, read the SAFETY INFORMATION section of this manual. •• Install unit indoors. •• Install unit on hard, flat surface for proper ventilation. •• Do not expose unit to rain or moisture. •• Do not place unit on or close to sources of heat. IMPORT ANT NOTICES TERMS AND CONDITIONS FOR USE OF PHONECELL ® PRODUCTS ("Product") These Terms and Conditions are a legal contract between you and Telular Corporation for the title toand use of the Product. BY RETAINING AND USING THE PRODUCT AFTER RECEIPT OF IT, YOUAGREE TO THE TERMS AND CONDITIONS INCLUDING WARRANTY DISCLAIMERS,LIMITATIONS OF LIABILITY AND INDEMNIFICATION PROVISIONS BELOW. IF YOU DO NOTAGREE TO THE TERMS AND CONDITIONS, DO NOT USE THE PRODUCT AND IMMEDIATELYRETURN THE UNUSED PRODUCT FOR A COMPLETE REFUND. You agree to accept soleresponsibility for any misuse of the Product by you; and, in addition, any negligent or illegal act oromission of your or your agents, contractors, servants, employees, or other users of the Product solong as the Product was obtained from you, in the use and operation of the Product. INDEMNIFICATION OF TELULAR CORPORATION ("TELULAR") YOU SHALL INDEMNIFY, DEFEND AND HOLD HARMLESS TELULAR FOR ANY OF THE COST,INCLUDING REASONABLE ATTORNEYS' FEES, AND FROM CLAIMS ARISING OUT OF YOU,YOUR CLIENTS' OR OTHER THIRD PARTIES' USE OR OPERATION OF THE PRODUCT: (i) FORMISUSE OR IN A MANNER NOT CONTEMPLATED BY YOU AND TELULAR OR INCONSISTENTWITH THE PROVISIONS OF THIS MANUAL; (ii) IN AN ILLEGAL MANNER OR AGAINST PUBLICPOLICY; (iii) IN A MANNER SPECIFICALLY UNAUTHORIZED IN THIS MANUAL; (iv) IN AMANNER HARMFUL OR DANGEROUS TO THIRD PARTIES; (v) FROM CLAIMS BY ANYONERESPECTING PROBLEMS, ERRORS OR MISTAKES OF THE PRODUCT; OR (vi)COMBINATION OF THE PRODUCT WITH MATERIAL, MODIFICATION OF THE PRODUCT ORUSE OF THE PRODUCT IN AN ENVIRONMENT NOT PROVIDED, OR PERMITTED, BYTELULAR IN WRITING. THE PARTIES SHALL GIVE EACH OTHER PROMPT NOTICE OF ANYSUCH COST OR CLAIMS AND COOPERATE, EACH WITH THE OTHER, TO EFFECTUATE THISINDEMNIFICATION, DEFENSE AND HOLD HARMLESS. TELULAR CORPORA TIO N Corporate Headquarters 647 North Lakeview Parkway Vernon Hills, Illinois 60061, USA http://www.telular.com Part Number 56033202 ©Telular Corporation, All Rights Reserved Please see the IMPORTANT NOTICES , SAFETY INFORMATION , and WARRANTY sections of this manual for important information on use, warranty, and indemnification. Phonecell ® SX6P CDMA iii User Manual T able of Content s Quick Connection Guide ...................................................................................................iList of Components............................................................................................................iSX6P Menu Structure ........................................................................................................iiSafe Operation Instructions ............................................................................................iiiImportant Notices .............................................................................................................i ii SX6P Setup ...................................................................................................................... ..1 RUIM Card Installation (RUIM Model Only) ................................................................................1Battery Installation ........................................................................................................... ............2 Battery Operation .............................................................................................................. ..........2 Location and Setup............................................................................................................. .........2 Connecting the Handset ......................................................................................................... .....3 Wall Mounting .................................................................................................................. ............3 Connecting the SX6P to AC Power .............................................................................................4RUIM Usage (RUIM Models Only) ..............................................................................................5 Getting to Know Your SX6P .............................................................................................6 Function Keys .................................................................................................................. ............6 LCD Screen Icons ............................................................................................................... ........7 Service Indication ............................................................................................................. …

Text truncated - open the document above for the full version.

EXHIBIT C - EUT EXTERNAL PHOTOGRAPHS EUT - Front View EUT – Rear View EUT Port View EUT Handset View EUT Base View EUT – Antenna View Power Adapter

EXHIBIT A - FCC ID LABELING AND WARNING STATEMENT Proposed FCC ID Label Specifications: Text is black or white in color and is left justified. Labels are silk-screened and shall be “permanently affixed” at a conspicuous location on the EUT. Proposed Label Location on EUT Rear View of the EUT/Proposed ID Label Location FCC Warning Statement A FCC Warning Statement is provided in the product manual. FCC ID: MTFSX6P200260C

EXHIBIT C - EUT INTERNAL PHOTOGRAPHS EUT – Cover off View EUT – Component View EUT – Solder View Keyboard and Display View

Copyright © 2005 by Telular Corporation. All Rights Reserved. Printed in the United States of America. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise without the prior written consent of Telular Corporation. TELULAR CORPORATION Product Specification Phonecell SX6P CDMA 200 Series Distribution Date: March 3, 2005 File Name: 90021201 R R PRODUCT SPECIFICATION Phonecell SX6P CDMA 200 Series Filename: 90021201 Page 2 of 2 Confidential and Proprietary 3/5/05 Specification subject to change without notice. Table of Contents 1.0 OVERVIEW..........................................................................................................................................5 1.1. Purpose and Scope ..................................................................................................................................5 1.2. Introduction.............................................................................................................................................5 1.3. Summary of Capabilities.........................................................................................................................5 1.4. Cellular Network Usage..........................................................................................................................5 1.5. Power Supply..........................................................................................................................................5 2.0 USER INTERFACE .............................................................................................................................6 2.1. Hook Operations .....................................................................................................................................6 2.1.1. Recognition of Seizure (Off-Hook) ...................................................................................................................................... 6 2.1.2. Recognition of Release of Seizure (On-Hook)..................................................................................................................... 6 2.2. Tone Generation .....................................................................................................................................6 2.2.1. Service Dial Tone ................................................................................................................................................................ 6 2.2.2. Non-Registered Dial Tone ................................................................................................................................................... 6 2.2.3. No-Service Tone................................................................................................................................................................... 6 2.2.4. Other Tones and Announcements ........................................................................................................................................ 6 2.2.5. Reorder Tone ....................................................................................................................................................................... 6 2.2.6. Receiver Off Hook (ROH) Tone........................................................................................................................................... 7 2.2.7. Post Receiver Off-Hook Operation ..................................................................................................................................... 7 2.2.8. Error Alert Tone .................................................................................................................................................................. 7 2.2.9. DTMF Tones ........................................................................................................................................................................ 7 2.3. Dialing ....................................................................................................................................................7 2.3.1. Dialing Buffer ...................................................................................................................................................................... 7 2.3.2. Recognition of Address Signaling ....................................................................................................................................... 7 2.3.3. End of Address Signaling .................................................................................................................................................... 8 2.4. Hookflash................................................................................................................................................8 2.5. In-Call DTMF Signaling.........................................................................................................................8 2.6. Alerts.......................................................................................................................................................8 2.6.1. On-Hook Call Alert (Ring Type) ......................................................................................................................................... 8 2.6.2. Off-Hook Call Alert (Ring Tone) ......................................................................................................................................... 8 2.6.3. Ring Volume......................................................................................................................................................................... 9 2.6.4. One-Minute Alert ................................................................................................................................................................. 9 2.6.5. Service Alert...........…

Text truncated - open the document above for the full version.

R R CORPORATION 10/19/05 Technology Center • 580 Old Willets Path • Hauppauge, NY 11788 • Phone: 631-232-6070 • Fax 631-232-6082 SX6P-200C CDMA Deskphone Tuning Procedure No mechanical adjustments exist within this unit. An automated factory Test and Calibration program is used for initial check out and setup of this unit. None of the following calibration adjustments are available to the end user. No hidden "back door" commands exist to allow changes to the non-volatile memory from the keypad. The following items are measured and correction tables are generated. Upon successful completion of all tests, this data is written into the radio's nonvolatile memory. Specifically: 1) 19.2 MHz Frequency Standard Sets the internal frequency standard exactly to 19.2 MHz, compensating for manufacturing tolerances. 2) Receiver gain control vs signal level, CELL 850 MHz band Calibrates receiver Automatic Gain Control (AGC) vs received signal level. 3) Receiver gain control vs channel number (frequency), CELL 850 band Generates and offset table of receiver AGC vs frequency. 4) Transmit gain control vs output power, CELL 850 band Calibrates transmitter AGC vs requested transmit signal level. 5) Transmit gain control vs channel number (frequency), CELL 850 band Generates an offset table of transmitter AGC vs frequency. 6) Transmit power detector vs power level, CELL 850 band Calibrates 850 power detector sensitivity. These data points are utilized by the radio to form multi-dimensional smoothed contour maps of exact correction values for each channel. Transmit power is adjusted by a closed looped feedback controller, initially based upon detected power output. Once in a call, power control is also based upon the received signal at the Base Station. By design, regardless of calibration data values, transmitter is incapable of exceeding maximum specified power output by more than approximately 1 dB. Transmit frequency initially uses the accuracy of the internal 19.2 MHz standard. Once registered with a cellular base station, unit locks onto base station, thereby further improving accuracy. Generates an offset table of receiver AGC level vs frequency (channel number). The DC Voltage/Current into the final stages is 4.05 Volts, 500 milliamps maximum.

Note: The test report is specially limited to the above company and this particular sample only. It may not be duplicated without prior written consent of Bay Area Compliance Laboratory Corporation. This report must not be used by the client to claim product certification, approval, or endorsement by NVLAP, NIST or any agency of the US Government. FCC PART 22 TYPE APPROVAL EMI MEASUREMENT AND TEST REPORT For Telular Corporation 580 Old Willets Path, Hauppauge, NY 11788 FCC ID: MTFSX6P200260C This Report Concerns: Original Report Equipment Type: CDMA 800MHz Wireless Deskphone Test Engineer: Daniel Deng / Report No.: R0510193 Report Date: 2005-11-01 Reviewed By: Richard Lee / Prepared By: Bay Area Compliance Laboratory Corporation (BACL) 230 Commercial Street Sunnyvale, CA 94085 Tel: (408) 732-9162 Fax: (408) 732 9164 Telular Corporation FCC ID: MTFSX6P200260C Report # R0510193RptRpt Page 2 of 24 FCC Part 22 Type Approval Report TABLE OF CONTENTS GENERAL INFORMATION.......................................................................................................................................4 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) ....................................................................................4 OBJECTIVE...................................................................................................................................................................4 RELATED SUBMITTAL(S)/GRANT(S).............................................................................................................................4 TEST METHODOLOGY..................................................................................................................................................4 TEST FACILITY.............................................................................................................................................................4 SYSTEM TEST CONFIGURATION ..........................................................................................................................6 JUSTIFICATION.............................................................................................................................................................6 BLOCK DIAGRAM.........................................................................................................................................................6 EQUIPMENT MODIFICATIONS.......................................................................................................................................6 LOCAL SUPPORT EQUIPMENT LIST AND DETAILS........................................................................................................6 REMOTE SUPPORT EQUIPMENT LIST AND DETAILS......................................................................................................6 CONFIGURATION OF TEST SYSTEM..............................................................................................................................6 SUMMARY OF TEST RESULTS ...............................................................................................................................7 §2.1047 - MODULATION CHARACTERISTIC .......................................................................................................8 APPLICABLE STANDARD..............................................................................................................................................8 TEST PROCEDURE........................................................................................................................................................8 TEST EQUIPMENT LIST AND DETAILS...........................................................................................................................8 ENVIRONMENTAL CONDITIONS....................................................................................................................................8 TEST RESULTS.............................................................................................................................................................8 §2.1053 - SPURIOUS RADIATED EMISSIONS .....................................................................................................10 APPLICABLE STANDARD............................................................................................................................................10 TEST PROCEDURE......................................................................................................................................................10 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................10 ENVIRONMENTAL CONDITIONS..................................................................................................................................10 TEST RESULT.............................................................................................................................................................11 §2.1046, §22.913(A) – CONDUCTED OUTPUT POWER.......................................................................................12 APPLICABLE STANDARD............................................................................................................................................12 TEST PROCEDURE......................................................................................................................................................12 TEST EQUIPMENT LIST AND DETAILS.........................................................................................................................12 ENVIRONMENTAL CONDITIONS..................................................................................................................................12 TEST RESULTS......................................................................................................................................…

Text truncated - open the document above for the full version.