MYT3X7733Electronic Key 3X7733

Opening and closing 56 Child-proof catchesChild-proof catches on the rear doorsThe child-proof catches prevent the rear doors being opened from the inside.The rear doors are equipped with child-proof catches. They can be operated using the ignition key.Engaging the child-proof catch– Turn the slot in the child-proof catch anti-clockwise Þ fig. 38 . Disengaging the child-proof catch– Turn the slot in the child-proof catch clockwise . When the child-proof catch is engaged, the inside door handle will not function, and the door can only be opened from the outside.Remote controlDescriptionThe radio-operated remote control will lock and unlock the vehicle without having to insert the key in the lock.The following functions are available:• Lock and unlock the vehicle • Unlock the boot lid All the turn signals will flash when the vehicle is locked or unlocked. In addition, the interior lights will automatically light up when the vehicle is unlocked and go out when the vehicle is locked, provided that the switch is in the courtesy light position.The remote control transmitter and the battery are integrated in the handle of the key. The receiver is in the interior of the vehicle. The maximum range of the remote control depends on various condi-tions. The range is reduced when the battery starts to lose power.The remote control incorporates a foldaway key that can be used to manually lock or unlock the vehicle and to start the engine.If a lost key has to be replaced, or if the receiver is repaired or replaced, the system must be initialised by an Audi dealer before the remote control will operate again.The radio-operated remote control conforms with all relevant requirements for Germany and has been approved by the Federal Approvals Office for Telecommunications of the Federal Republic Of H A A B A B8E-034 Fig. 38 Child-proof catches on the rear doors A B A A part13.fm Seite 56 Mittwoch, 1. November 2000 11:32 23 Opening and closing 57 Controls and equip-ment Safety Driving tips General maintenance Do-it-yourself Technical data Germany. All components are marked in accordance with the current legal requirements. This official certification forms the basis for obtaining approval for use in other countries. Note • The remote control is automatically deactivated when the igni- tion is switched on.• The function of the remote control may be temporarily impaired by interference from other radio signals (for example from a mobile telephone or TV transmitter) if these are in the same frequency range and close to the vehicle.Applies to vehicles with remote controlLocking and and unlocking the vehicleUnlocking the vehicle Ô – Press button Þ fig. 39 for about one second. Locking the vehicle Õ – Press button for about one second.Opening the boot lid s – Press button and hold for at least one second. The turn signals will flash twice as confirmation when you unlock the car. The vehicle will be locked again automatically if you do not open one of the doors or the boot lid within 60 seconds after unlocking the car with button . This function prevents the vehicle from remaining unlocked if the unlocking button is pressed by mistake.On vehicles with the security central locking feature, you can unlock just the driver's door and the tank flap by pressing button once, or the whole vehicle by pressing the button twice.The turn signals flash once when the vehicle is locked to confirm that the doors and boot lid are properly locked. On vehicles equipped with anti-theft alarm* the system also checks that the tank flap has been properly closed and locked.When the car is unlocked, the driver's seat and the exterior mirrors will be automatically adjusted to the positions stored in the seat memory* for the key which is being used.The interior lights will automatically light up when the vehicle is unlocked and go out when the vehicle is locked, provided that the switch is in the courtesy light position. B8E-036 A B C Fi g . 3 9 R e m o t e c o n t ro l key: control buttons A A A B A C A A A A part13.fm Seite 57 Mittwoch, 1. November 2000 11:32 23 CONTROLS AND EQUIPMENT 67 67 l Certification The remote control device complies withPart 15 of the FCC Rules. Operation is sub-ject to the following conditions:1 - this device may not cause harmful in- terference, and 2 - this device must accept any interfer- ence received, including interferencethat may cause undesired operation. The manufacturer is not responsible forANY RADIO OR TV Interference caused byunauthorized modifications to this equip-ment. Such modifications could void theuser ’ s authority to operate the equipment. Anti-theft alarm systemThe anti-theft alarm system triggers anacoustic alarm and switches on the emer-gency flasher if it senses unauthorized inter-ference with the vehicle.When the vehicle is locked the alarm sy-stem monitors and protects the followingparts of the vehicle:l engine compartment l luggage compartment l doors l factory installed radio l passenger compartment l ignition. The alarm system is switched on or offwhenever you lock or unlock the vehicle.Simply turn the key to the lock or unlockposition or use the remote control.The system is activated about 30 secondsafter the vehicle is locked, and the indicatorlights on the front door window sills startflashing. The horn sounds briefly when the car islocked to confirm that the alarm system isoperative and that all doors, hood and rearlid are properly closed. If the horn does notsound, or the indicator lights do not flash,check all doors, rear lid and hood and closethem properly. The horn will also sound ifthe door, lid and hood are closed when thesystem is already switched on.The rear lid can be opened separately evenwhen the system is active. When the rearlid is closed the luggage compartment willagain be included in the alarm circuit.When the system is switched on the alarmwill be triggered if one of the doors, the en-gine hood or the rear lid are opened, or if theignition is switched on or the r…

Text truncated - open the document above for the full version.

ATTESTATION STATEMENT FCC ID: MYT3X7733 Electronic Key 3X7733 SUMMARY: All tests according to FCC Part Subpart C Paragraph 15.231 n - Performed The equipment under test n - Fulfills the general approval requirements of FCC Part Subpart C Paragraph 15.231 - MIKES BABT PRODUCT SERVICE GmbH - Responsible Engineer _____________________________ Nikolaus Fischer

FCC ID: MYT3X7733 Attachment E1 TEMIC 3X7733 File-No. T 19728-00 NF MIKES BABT PRODUCT SERVICE GmbH w Ohmstrasse 2-4 w D-94342 Strasskirchen w Tel.:+49 94 24 94 07-0 w Fax:+49 94 24 94 07-60 Rev.Nr. 8.5 Transmitter 315 MHz

FCC ID: MYT3X7733 Attachment E2 TEMIC 3X7733 File-No. T 19728-00 NF MIKES BABT PRODUCT SERVICE GmbH w Ohmstrasse 2-4 w D-94342 Strasskirchen w Tel.:+49 94 24 94 07-0 w Fax:+49 94 24 94 07-60 Rev.Nr. 8.5 Transmitter 315 MHz

FCC ID: MYT3X7733 TTI - P-G 009 / 98-00 TTI - P-G 089 / 94-50 File No. T 19728-1-00 NF , Page 1 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.5 E M I S S I O N -- T E S T R E P O R T Testreport file no. : T 19728-1-00 NF ______________ Date : Dec. 08, 2000 of issue _________________ Model:3X7733 ______________________________________________ Type:Electronic Key ______________________________________________ Applicant:TEMIC TELEFUNKEN microelectronic GmbH ______________________________________________ Manufacturer:TEMIC TELEFUNKEN microelectronic Phils.Inc. ______________________________________________ Licence holder:TEMIC TELEFUNKEN microelectronic GmbH ______________________________________________ Address:Ringlerstraße 17 ______________________________________________ 85057 Ingolstadt ______________________________________________ Test result accrdg. to the regulation(s) at page 3 : POSITIVE This testreport with appendix consists of 29 pages. The testresult only responds to the tested sample. It is not allowed to copy this report even partly without the allowance of the testlaboratory. FCC ID: MYT3X7733 File No. T 19728-1-00 NF , Page 2 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.5 D I R E C T O R Y Page A) Documentation Directory2 ________ Testregulations3 ________ General information4-5 ________ Discovery of worst case condition6 ________ Equipment under Test16 ________ Summary17 ________ B) Testdata Conducted emissions 10/150 kHz - 30 MHz7 ________ Spurious emissions (magnetic field) 10 kHz - 30 MHz8-9 ________ Spurious emissions (electric field) 30 MHz - 1000 MHz10-11 ________ Spurious emissions (electric field) 1 GHz - 18 GHz12-13 ________ Raiated power of the fundamental wave14 ________ Conducted power of the fundamental wave measured on15 the antenna terminals ________ Attachment A)TestdataA1-A4 ________ B)List of Test EquipmentB1 ________ C) Photos of the test setupC1-C2 ________ D)Technical description of the test sampleD1-D3 (e.g.CDF, Declaration) ________ E) Photos of the EuTE1-E2 ________ F)Measurement Protocol for FCC, VCCI and AUSTEL-- ________ FCC ID: MYT3X7733 File No. T 19728-1-00 NF , Page 3 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.5 T E S T R E G U L A T I O N S The tests were performed according to following regulations : o- EN 50081-1/ 2.1991 o- EN 50081-2/ 7.1993 -------------------------------------------------------------------------------- o- EN 55011/ 3.1991o- Group 1o- Group 2 o- class Ao- class B o- EN 55014/ 4.1993o- Household appliances and similar o- tools o- Semiconductor devices o- EN 55014 / A2:1990 o- EN 55104/ 5.1995Category: o- EN 55015 / A1:1990 o- EN 55015 / 12.1993 o- EN 55022 / 5.1995o- class Ao- class B o- prEN 55103-1/ 3.1995 o- prEN 50121-3-2/ 3.1995 o- EN 60601-1-2/ 4.1994 o- VCCIo- class 1o- class 2 n- Part 15 Subpart C (15.231) FCC ID: MYT3X7733 File No. T 19728-1-00 NF , Page 4 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.5 A D D R E S S O F T H E T E S T L A B O R A T O R Y n-MIKES PRODUCT SERVICE GmbH Ohmstrasse 2-4 D - 94342 Strasskirchen o-______________________________________ ______________________________________ ______________________________________ E N V I R O N M E N T A L C O N D I T I O N S Temperature:15-35 ° C ______ Humidity45-60 % ______ Atmospheric pressure 860-1060 mbar _________ POWER SUPPLY SYSTEM UTILIZED Power supply system: Battery Unom = 3.0V DC STATEMENT OF MEASUREMENT UNCERTAINTY The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities that can account for a nominal measurement error of ±4dB. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. SHORT DESCRIPTION OF THE EQUIPMENT UNDER TEST (EUT) The Electronic Key is part of a vehicle security system. The key is for lock and unlock the doors and the trunk by remote control. Number of received/tested samples:1/1 DEFINITIONS FOR SYMBOLS USED IN THIS TEST REPORT n -Black box indicates that the listed condition, standard or equipment is applicable for this Report. o -Blank box indicates that the listed condition, standard or equipment was not applicable for this Report. FCC ID: MYT3X7733 File No. T 19728-1-00 NF , Page 5 of 17 MIKES BABT PRODUCT SERVICE GmbH Ohmstrasse 2-4 94342 Strasskirchen Tel:+9424-9407-0 Fax:+9424-9407-60 Rev.No. 8.5 M E A S U R E M E N T P R O T O C O L F O R F C C , V C C I A N D A U S T E L Test Methodology Conducted and radiated emission testing is performed according to the procedures in International Special Committee on Radio Interference (CISPR) Publication 22 (1993), European Standard EN 55022 and Australian Standard AS 3548 (which are based on CISPR 22). The Japanese standard, "Voluntary Control Council for Interference (VCCI) by Data Processing Equipment and Electronic Office Machines, Technical Requirements" is technically equivalent to CISPR 22 (1993). For official compliance, a conformance report must be sent to and accepted by the VCCI. In compliance with FCC Docket 92-152, "Harmonization of Rules for Digital Devices Incorporate International Standards", testing for FCC compliance may be done following the ANSI C63.4-1992 procedures and using the FCC limits or the CISPR 22 Limits. Measurement Error The test system for conducted emissions is defined as the LISN, tuned receiver and coaxial cable. The test system for spurious emissions is defined as the antenna, the pre-amplifier, the tuned receiver and the coaxial cable. These test systems have an expected error of ±3 dB.…

Text truncated - open the document above for the full version.

FCC ID: MTY3X7733 Attachment C1 of C2: Photo documentation File No.: T 19728-1-00 NF MIKES BABT PRODUCT SERVICE GmbH w Ohmstrasse 2-4 w D-94342 Strasskirchen w Tel.:+49 94 24 94 07-0 w Fax:+49 94 24 94 07-60 Rev.Nr. 8.5 Test-Setup: Radiated emission < 1 GHz TEMIC 3X7733 FCC ID: MTY3X7733 Attachment C2 of C2: Photo documentation File No.: T 19728-1-00 NF MIKES BABT PRODUCT SERVICE GmbH w Ohmstrasse 2-4 w D-94342 Strasskirchen w Tel.:+49 94 24 94 07-0 w Fax:+49 94 24 94 07-60 Rev.Nr. 8.5 Test-Setup: Radiated emission > 1 GHz TEMIC 3X7733