N7NEM7700Cellular/PCS WCDMA and LTE Band 4/17 Modem

AirPrime EM7700 Hardware Integration Guide 4112206 Rev 2 Preface Rev 2 Apr.12Proprietary and Confidential3 Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data. Safety and Hazards Do not operate the Sierra Wireless modem in areas where blasting is in progress, where explosive atmospheres may be present, near medical equipment, near life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the Sierra Wireless modem MUST BE POWERED OFF. The Sierra Wireless modem can transmit signals that could interfere with this equipment. Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard systems. Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless modems may be used at this time. The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of a vehicle. Doing so will detract from the driver or operator's control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence. Limitation of Liability The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND /OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY. Notwithstanding the foregoing, in no event shall Sierra Wireless and /or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product. AirPrime EM7700 Hardware Integration Guide 4Proprietary and Confidential4112206 PatentsThis product may contain technology developed by or for Sierra Wireless Inc. This product includes technology licensed from QUALCOMM ® . This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents licensed from InterDigital Group. Copyright© 2012 Sierra Wireless. All rights reserved. TrademarksSierra Wireless™, AirPrime™, Watcher™, and the Sierra Wireless logo are trademarks of Sierra Wireless. Windows ® is a registered trademark of Microsoft Corporation. Other trademarks are the property of their respective owners. Contact Information Consult our website for up-to-date product descriptions, documentation, application notes, firmware upgrades, troubleshooting tips, and press releases: www.sierrawireless.com Revision History Sales Desk:Phone:1-604-232-1488 Hours:8:00 AM to 5:00 PM Pacific Time E-mail:[email protected] Post:Sierra Wireless 13811 Wireless Way Richmond, BC Canada V6V 3A4 Fax:1-604-231-1109 Web:www.sierrawireless.com Revision number Release dateChanges 1April 2012•FCC submission 2April 2012•Updated gain values in Regulatory section Rev 2 Apr.12Proprietary and Confidential5 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 The Universal Development Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Required connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Power Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Overview of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Power signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Module power states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 RF Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 RF connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Ground connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Shielding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Antenna and cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Interference and sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Methods to mitigate decreased Rx performance . . . . . . . . . . . . . . . . . . . 13 Radiated Spurious Emissions (RSE) . . . . . . . . . . . . . . . . . . . . . . . . . . . …

Text truncated - open the document above for the full version.

24 April 2012 Federal Communications Commission Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: Re: Confidentiality Request for FCC ID: N7NEM7700 We hereby request that the exhibits listed below, submitted with our application for certification, be withheld from public disclosure. This request is made under the provisions of Section 0.457(d) and 0.459 of the Commission’s Rules, and Section 522(b)(4) of the Freedom of Information Act. We cite trade secrets as the reason and purpose of the request.  Schematics  Block Diagram  Operation Description  Tune Up Procedure Furthermore, pursuant to Public Notice DA 04-1705 in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, we request the following exhibits be withheld from public viewing for a short limited time of 180 days from the date of the Grant of Equipment Authorization, due to the sensitive business information:  User Manual  Product Photos  Test Setup Photos Best Regards, Ying Wang Manager, Regulatory Compliance

Modular Approval Checklist FCC ID: N7NEM7700 Item Requirements EUT 1 The radio elements must have the radio frequency circuitry shielded Module RADIO elements are shielded. Please see submitted external photograph exhibits 2 The module must have buffered modulation/data inputs Module chipset design incorporates integrated buffer circuitry 3 The module must contain power supply regulation on the module Module chipset incorporates voltage regulation to transceiver circuitry 4 The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s) No applicable to licensed modules 5 The module must demonstrate compliance in a stand-alone configuration EUT conformance testing was performed in a standalone configuration 6 The licensed module must have a FCC ID label on the module itself. That FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text: Contains “FCC ID: N7NEM7700” Please refer to FCC ID label format. Labeling instruction has been provided in the user manual exhibit(s). 7 The module must comply with all specific rules applicable to the transmitter. The grantee must provide comprehensive instructions to explain compliance requirements The Module is compliant with all applicable FCC rules. Compliance requirements are stated in the user manual exhibit(s). 8 The module must comply with RF exposure requirements Compliance with RF exposure requirements is addressed in RF exposure report

EM7700 External Photos EM7700 Top View EM7700 Bottom View

EM7700 Label Location Model: EM7700 FCC ID: N7NEM7700 EM 7700

EM7700 Internal Photos EM7700 Top View EM7700 Bottom View

MPE Evaluation for EM7700 Module 04/24/2012 1. Introduction In this application we seek for modular approval to the EM7700 module for use in standalone and collocated simultaneous transmission under mobile configuration. This Maximum Permissive Exposure (MPE) report demonstrates compliance analysis for EM7700 module with FCC CFR 47 §2.1091 for standalone and collocated transmission in mobile exposure conditions. The MPE analysis is limited for US bands only. The general population/uncontrolled exposure limits are applicable to situations in which the general public may be exposed or in which persons who are exposed as a consequence of their employment may not be made fully aware of the potential for exposure or cannot exercise control over their exposure. Any collocated transmitter must have a valid FCC ID documenting equivalent or degraded RF characteristics with the collocated parameters defined in this MPE report. A separation distance of 20cm or more shall be maintained between the end user and each WWAN, WiMAX or WLAN, and Bluetooth transmitting antenna. Portable user conditions or additional collocated transmitters not allowed based on this RF exposure analysis require a Class II permissive change and updated RF exposure report. 2. RF Exposure Limits and Equations FCC RULES: According to FCC OET Bulletin 65 Supplement C, the criteria listed in Table 1 shall be used to evaluate the environmental impact of human exposure to radio frequency (RF) radiation as specified in §1.1307. Table 1 : Limits for Maximum Permissible Exposure (MPE) EQUATIONS: Power density is given by : S = EIRP / (4 * Pi * D^2) where S = Power density (mW/cm^2) EIRP = Equivalent Isotropic Radiated Power (mW) D = Separation distance (cm) 3. Product Declarations The EM7700 module can be installed for use in any mobile host as long as the antenna gain of the host antenna does not exceed the gain listed in table 2. This MPE analysis is applicable to any collocated transmitters with transmit power: - less than or equal to 29.0dBm for WLAN/WiMAX; and - less than or equal to 15.0dBm for BT. Specific FCC IDs for those devices are not necessary or identified in this analysis providing they are classified as mobile transmitters. A 100% duty cycle is used for calculations to present a worse-case analysis when applicable. Mode Equipment Category Max Transmitter Duty Cycle Transmitter Range (MHz) Maximum Conducted Power Max Antenna Gain (dBi) (dBm) (W) Standalone Collocated UMTS HSDPA HSUPA 100% 824 - 849 24.0 0.25 9.5 6.5 1850 - 1910 24.0 0.25 9.0 9.0 LTE Band 17 Band 4 100% 704 - 716 24.0 0.25 9.0 6.0 1710 - 1755 24.0 0.25 6.0 6.0 Table 2: EM7700 Standalone and Collocated Transmission Declarations 4. MPE Calculations The WWAN MPE calculations are based on conservative conducted transmit power exceeding those listed in the FCC ID N7NEM7700 filing. The higher transmit power levels are used to present a worst case assessment. The WiMAX, WLAN, and BT transmit power and antenna gain parameters represent a maximum transmit power for a given frequency band. Integration of either a WiMAX or WLAN, and BT module that exceeds the parameters requires a new FCC authorization or permissive change application. A maximum antenna gain of 5 dBi for WLAN/WiMAX/BT has been assumed for all collocated antennas. Table 3 and 4 summarize transmitter parameters associated with this analysis. 4.1. Individual Transmitter Calculations 4.1.1. Maximum Output Power The maximum power calculations for EM7700 per wireless technology are shown in Table 3 Technology Frequency (MHz) Maximum Conducted Power (dBm) Maximum Conducted Power (W) Maximum Antenna Gain (dBi) Duty Cycle Max EIRP (dBm) Max EIRP (W) Max ERP (dBm) Max ERP (W) Max output power limit EM7700 module (Standalone) UMTS 824 - 849 24.0 0.251 9.5 1.000 33.500 2.239 31.360 1.368 7 W ERP UMTS 1850 - 1910 24.0 0.251 9.0 1.000 33.000 1.995 30.860 1.219 2 W EIRP LTE 704 - 716 24.0 0.251 9.0 1.000 33.000 1.995 30.860 1.219 3 W ERP LTE 1710 - 1755 24.0 0.251 6.0 1.000 30.000 1.000 27.860 0.611 1 W EIRP Table 3: EM7700 Maximum Output Power Calculation According to FCC 2.1091(c), mobile devices that are authorized under subpart H of part 22, 24, and 27, are subject to routine environmental evaluation for RF exposure prior to equipment authorization or use if they operate at frequencies of 1.5GHz or below and their effective radiated power (ERP) is 1.5 watts or more, or if they operate at frequencies above 1.5GHz and their ERP is 3 watts or more. Otherwise, routine environmental evaluation for RF exposure is categorical excluded. 4.1.2. Power Density The power density calculations for the individual transmitters per wireless technology at an exposure minimum separation distance of 20cm are shown in Table 4. For frequency dependent limit, the lowest transmitter frequency was used to represent the lowest MPE limit in this analysis (eg. 824MHz = 0.549mW/cm 2 ) The WiMAX, WLAN, and BT power levels listed represent the worse-case scenario for corresponding frequency ranges given. Technology Frequency (MHz) Maximum Conducted Power (dBm) Maximum Conducted Power (W) Maximum Antenna Gain (dBi) Duty Cycle Average EIRP (dBm) Average EIRP (mW) Power Density @ 20cm (mW/cm^2) FCC MPE Limit (mW/cm^2) EM7700 Module (Standalone) UMTS 824 - 849 24.0 0.251 9.5 1.000 33.50 2238.721 0.445 0.549 UMTS 1850 - 1910 24.0 0.251 9.0 1.000 33.00 1995.262 0.397 1.000 LTE 704 - 716 24.0 0.251 9.0 1.000 33.00 1995.262 0.397 0.469 LTE 1710 - 1755 24.0 0.251 6.0 1.000 30.00 1000.000 0.199 1.000 EM7700 Module (Collocated) UMTS UMTS 824 - 849 24.0 0.251 6.5 1.000 30.50 1122.018 0.223 0.549 UMTS UMTS 1850 - 1910 24.0 0.251 9.0 1.000 33.00 1995.262 0.397 1.000 LTE LTE 704 - 716 24.0 0.251 6.0 1.000 30.00 1000.000 0.199 0.469 LTE LTE 1710 - 1755 24.0 0.251 6.0 1.000 30.00 1000.000 0.199 1.000 Other Collocated Transmitters WLAN 2400 - 2500 29.0 0.794 5.0 1.000 34.00 2511.886 0.500 1.000 WLAN 5150 - 5850 29.0 0.794 5.0 1.000 34.00 2511.886 0.500 1.00…

Text truncated - open the document above for the full version.

 2012 Sierra Wireless, Inc. This document contains information which is proprietary and confidential to Sierra Wireless, Inc. Disclosure to persons other than the officers, employees, agents, or subcontractors of the Company or licensee of this document without the prior written permission of Sierra Wireless, Inc. is strictly prohibited. EM7700 Module Test Report for FCC Certification FCC ID: N7NEM7700 SIERRA WIRELESS, INC. FCC Part 22/24/27, RSS-132/133/139/199 EM7700 April 11, 2012 Page 2 of 81  2012 Sierra Wireless, Inc. The contents of this page are subject to the confidentiality information on page one. Table of Contents 1 Introduction and Purpose ......................................................................... 4 2 Test Summary .......................................................................................... 4 3 Description of Equipment Under Test ..................................................... 4 4 RF Power Output ..................................................................................... 5 4.1 Test Equipment.................................................................................................... 5 4.2 Test Procedure .................................................................................................... 5 4.2.1 WCDMA/HSDPA/HSUPA Max Power Setup ........................................... 6 4.2.2 LTE Max Power Setup ................................................................................. 8 4.3 Maximum Transmit Power Test Results ............................................................. 8 4.3.1 Test Results for WCDMA/HSDPA/HSUPA Output Power ..................... 8 4.3.2 Test Results for LTE Output Power ........................................................... 9 5 Occupied Bandwidth .............................................................................. 14 5.1 Test Procedure .................................................................................................. 14 5.2 Test Equipment.................................................................................................. 15 5.3 Test Results ....................................................................................................... 15 5.3.1 WCDMA Summary Results ....................................................................... 15 5.3.2 LTE Summary Results ............................................................................... 15 5.3.3 WCDMA Rel99 Test Plots.......................................................................... 16 5.3.4 HSDPA Rel5 Test Plots .............................................................................. 17 5.3.5 HSUPA Rel6 Test Plots .............................................................................. 18 5.3.6 LTE Test Plots ............................................................................................. 19 6 Out of Band Emissions at Antenna Terminals ...................................... 23 6.1 Test Procedure .................................................................................................. 23 6.2 Test Equipment.................................................................................................. 24 6.3 Test Results ....................................................................................................... 24 6.3.1 WCDMA Rel99 Test Plots.......................................................................... 25 6.3.2 LTE Test Plots ............................................................................................. 33 7 Block Edge Compliance ........................................................................ 46 7.1 Test Procedure .................................................................................................. 46 7.2 Test Equipment.................................................................................................. 46 7.3 Test Results ....................................................................................................... 47 7.3.1 WCDMA Test Plots .................................................................................... 49 7.3.2 HSDPA Test Plots ....................................................................................... 51 7.3.3 HSUPA Test Plots ....................................................................................... 53 7.3.4 LTE Test Plots ............................................................................................. 55 8 Frequency Stability versus Temperature ............................................... 71 8.1 Summary of Results ........................................................................................... 71 8.2 Test Procedure .................................................................................................. 71 8.3 Test Equipment.................................................................................................. 71 8.4 Test Results ....................................................................................................... 72 8.4.1 UMTS Frequency Error over Temperature ................................................ 72 8.4.2 LTE Frequency Error over Temperature ................................................... 72 SIERRA WIRELESS, INC. FCC Part 22/24/27, RSS-132/133/139/199 EM7700 April 11, 2012 Page 3 of 81  2012 Sierra Wireless, Inc. The contents of this page are subject to the confidentiality information on page one. 9 Frequency Stability versus Voltage ....................................................... 73 9.1 Summary of Results ........................................................................................... 73 9.2 Test Procedure .................................................................................................. 73 9.3 Test Equipment.................................................................................................. 73 9.4 Test Results ........................................................…

Text truncated - open the document above for the full version.

China Telecommunication Technology Labs. ® TEST REPORT REPORT NUMBER: I12GC0264-FCC-RF ON Type of Equipment: Wireless Modules Type of Designation: EM7700 Manufacturer: Sierra Wireless Inc. ACCORDING TO FCC CFR Part 2, FREQUENCY ALLOCATIONS AND RADIO TREATY MATTERS; GENERAL RULES AND REGULATIONS; e-CFR, Oct 1, 2011 PART 22, PUBLIC MOBILE SERVICES ,Oct 1, 2011 PART 24, PERSONAL COMMUNICATIONS SERVICES ,Oct 1, 2011 PART 27, MISCELLANEOUS WIRELESS COMMUNICATIONS SERVICES, Oct 1, 2011 China Telecommunication Technology Labs. Month date, year Apr, 19, 2012 Signature He Guili Director FCC Parts 2, 22, 24,27 Equipment:EM7700 REPORT NO.: I12GC0264-FCC-RF Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 68011404 Web:http://www.chinattl.com Page 2 of 20 China Telecommunication Technology Labs. ® FCC ID: N7NEM7700 Report Date: 2011-04-19 Test Firm Name: China Telecommunication Technology Labs Registration Number: 840587 Statement The measurements shown in this report were made in accordance with the procedures described on test pages. All reported tests were carried out on a sample equipment to demonstrate limited compliance with FCC CFR 47 Parts 2, 22, 24 and 27. The sample tested was found to comply with the requirements defined in the applied rules. FCC Parts 2, 22, 24,27 Equipment:EM7700 REPORT NO.: I12GC0264-FCC-RF Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 68011404 Web:http://www.chinattl.com Page 3 of 20 China Telecommunication Technology Labs. ® CONTENTS 1 GENERAL INFORMATION ................................................................ 4 1.1 NOTES ......................................................................................... 4 1.2 TESTERS ....................................................................................... 5 1.3 TESTING LABORATORY INFORMATION ...................................................... 6 1.4 DETAILS OF APPLICANT OR MANUFACTURER ............................................... 7 2 TEST ITEM ...................................................................................... 8 2.1 GENERAL INFORMATION ..................................................................... 8 2.2 OUTLINE OF EUT ............................................................................. 8 2.3 MODIFICATIONS INCORPORATED IN EUT .................................................. 8 2.4 EQUIPMENT CONFIGURATION ............................................................... 8 2.5 OTHER INFORMATION ........................................................................ 8 3 SUMMARY OF TEST RESULTS .......................................................... 9 4 TEST RESULTS .............................................................................. 10 4.1 RADIATED SPURIOUS EMISSION ........................................................... 10 ANNEX A EXTERNAL PHOTOS ........................................................... 18 ANNEX B INTERNAL PHOTOS ........................................................... 19 ANNEX C DEVIATIONS FROM PRESCRIBED TEST METHODS .............. 20 FCC Parts 2, 22, 24,27 Equipment:EM7700 REPORT NO.: I12GC0264-FCC-RF Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 68011404 Web:http://www.chinattl.com Page 4 of 20 China Telecommunication Technology Labs. ® 1 General Information 1.1 Notes All reported tests were carried out on a sample equipment to demonstrate limited compliance with FCC CFR 47 Parts 2, 22, 24 and 27. The test results of this test report relate exclusively to the item(s) tested as specified in section 2. The following deviation from, additions to, or exclusions from the test specifications have been made. See Annex C. China Telecommunication Technology Labs. (CTTL) authorizes the applicant or manufacturer (see section 1.4) to reproduce this report provided, and the test report may only be reproduced or published in full. Reproduction or publication of extracts from the report requires the prior written approval of CTTL Mr. He Guili. Any use which a third party makes of this report, or any reliance on or decisions to be made based on it, are the responsibility of such third parties. CTTL accepts no responsibility for damages, if any, suffered by any third party as a result of decisions made or actions based on this report. FCC Parts 2, 22, 24,27 Equipment:EM7700 REPORT NO.: I12GC0264-FCC-RF Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 68011404 Web:http://www.chinattl.com Page 5 of 20 China Telecommunication Technology Labs. ® 1.2 Testers Name: Yuan Yuan Position: Engineer Department: Department of EMC test Date: 2012-04-13~2012-04-19 Signature: Editor of this test report: Name: Pan Yang Position: Engineer Department: Department of EMC test Date: 2012-04-19 Signature: Technical responsibility for area of testing: Name: Zou Dongyi Position: Manager Department: Department of EMC test Date: 2012-04-19 Signature: FCC Parts 2, 22, 24,27 Equipment:EM7700 REPORT NO.: I12GC0264-FCC-RF Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 68011404 Web:http://www.chinattl.com Page 6 of 20 China Telecommunication Technology Labs. ® 1.3 Testing Laboratory information 1.3.1 Location Name: China Telecommunication Technology Labs. Address: No. 11, Yue Tan Nan Jie, Xi Cheng District BEIJING P. R. CHINA, 100083 Tel: +86 10 68094053 Fax: +86 10 68011404 Email: [email protected] 1.3.2 Details of accreditation status Accredited by: China National Accreditation Service for Conformity Assessment (CNAS) Registration number: CNAS Registration No. CNAS L0570 Standard: ISO/IEC 17025:2005 1.3.3 Test location, where different from section 1.3.1 Name: ------ Street: ------ City: ------ Country: ------ Telephone: ------ Fax: ------ Postcode: ------ FCC Parts 2, 22, 24,27 Equipment:EM7700 REPORT NO.: I12GC0264-FCC-RF Address：11 YUE TAN NAN JIE, BEIJING, P.R.C,100045 Tel:+86 10 68094053 FAX:+86 10 6801…

Text truncated - open the document above for the full version.

Test Setup photo RSE RSE Stand-alone