N7NEM92Radio Module

EM929X Hardware Integration Guide 41114769 Rev 2.2 Proprietary and Confidential Contents subject to change Product Technical Specification Rev. 2.2 September 2023241114769 Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data. Safety and Hazards Do not operate the Sierra Wireless modem in areas where blasting is in progress, where explosive atmospheres may be present, near medical equipment, near life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the Sierra Wireless modem MUST BE POWERED OFF. The Sierra Wireless modem can transmit signals that could interfere with this equipment. Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard systems. Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless modems may be used at this time. The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of a vehicle. Doing so will detract from the driver or operator's control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence. Limitation of Liability The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY. Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product. Copyright© 2023 Sierra Wireless. All rights reserved. TrademarksSierra Wireless ® , AirLink ® , AirVantage ® and the Sierra Wireless logo are registered trademarks of Sierra Wireless, Inc. Preface Rev. 2.2 September 2023341114769 Windows ® is a registered trademark of Microsoft Corporation. QUALCOMM ® is a registered trademark of QUALCOMM Incorporated. Used under license. Other trademarks are the property of their respective owners. Contact Information Revision History Sales information and technical support, including warranty and returns Web: sierrawireless.com/company/contact-us/ Global toll-free number: 1-877-687-7795 6:00 am to 6:00 pm PST Corporate and product informationWeb: sierrawireless.com Rev #Release dateChanges 1August 2023Document created 2September 2023Updated Regulatory approvals 2.1September 2023Updated Important Compliance Information for the United States 2.2September 2023Added Important Compliance Information for Canada Rev. 2.2 September 2023441114769 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Required Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Module Power States. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 RF Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Antenna Receptacles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5G NR Sub-6G/LTE/WCDMA /GNSS Receptacles . . . . . . . . . . . . . . . . . . . . . . . . 10 RF Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5G NR Sub-6G/GNSS Antennas and Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Shielding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Ground Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Interference and Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Interference from Other Wireless Devices . . . . . . . . . . . . . . . . …

Text truncated - open the document above for the full version.

050523-17 rev 8 Certification Application Attestation Statements Date: September 6, 2023 American Certification Body, Inc. Suite 300, 313 Park Avenue Falls Church, VA 22046 To Whom It May Concern: Statement for 47 CFR section 2.911(d)(5)(i) Sierra Wireless, ULC certifies that as of the date of the application the equipment for which authorization is sought is not “covered” equipment 1 prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, including affiliates or subsidiaries of the named companies, the applicant must include an explanation on why the equipment is not “covered” equipment. Statement for 47 CFR section 2.911(d)(5)(ii) Sierra Wireless, ULC (“the applicant”) certifies that, as of the date of the filing of this application, the applicant is not identified on the Covered List as an entity producing “covered” equipment. Thank you, By: __________________________ ______Ying Wang __________ (Signature 2 ) (Print name) Title: Director, Regulatory Compliance Company: Sierra Wireless, ULC Telephone: +1 604 231 1100 1 - The Commission’s Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commission’s website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes “covered” equipment. https://www.fcc.gov/supplychain/coveredlist . 2 - Letters must be placed on appropriate letterhead.

Sierra Wireless, ULC 13811 Wireless Way Richmond BC, V6V 3A4 Canada Tel: 604-231-1100 ; Fax: 604-231-1109 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Certification designating a U.S. agent for service of process pursuant to Part 2.911(d)(7) To whom it may concern, Sierra Wireless, ULC, Grantee Code: N7N, FRN: 0005810874 (“the applicant”) certifies that, as of the date of the filing of application, Semtech Corporation (“the agent”) is designated as the U.S. agent for the purpose of accepting service of process on behalf of the applicant. The physical U.S. address, email for the designated agent are: Physical U.S. address: 200 Flynn Road, Camarillo, California, 93012-8790 Email: [email protected] FRN: 0026496067, 0027931203 The applicant accepts to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. The applicant further acknowledges their responsibility to inform the FCC whenever the agent information changes. The agent accepts the designation by (the applicant) as the U.S. agent to accept service of process includes, but is not limited to, delivery of any correspondence, notices, orders, decisions, and requirements of administrative, legal, or judicial process related to Commission proceedings. Signed by the Applicant Signed by the Agent (if different from the Applicant) Name: Ying Wang Name: Ying Wang Title: Director, Regulatory Compliance Title: Director, Regulatory Compliance Email: [email protected] Email: [email protected] Date: September 26, 2023 Date: September 26, 2023

070920-02b Request for Modular/Limited Modular Approval Date: September 21, 2023 Subject: Manufacturer’s Declaration for ☒ - Modular Approval ☐ - Split Modular Approval ☐ - Limited Modular Approval ☐ - Limited Split Modular Approval Confidentiality Request for: _FCC ID: N7NEM92 8 Basic Requirements – FCC Part 15.212(a)(1) For Items Marked “NO(*)”, the Limited Module Description Must be Filled Out on the Following Pages Modular Approval Requirement Requirement Met 1. The modular transmitter must have its own RF shielding. This is intended to ensure that the module does not have to rely upon the shielding provided by the device into which it is installed in order for all modular transmitter emissions to comply with FCC limits. It is also intended to prevent coupling between the RF circuitry of the module and any wires or circuits in the device into which the module is installed. Such coupling may result in non-compliant operation. The physical crystal and tuning capacitors may be located external to the shielded radio elements. 15.212(a)(1)(i) ☒ - YES ☐ - NO(*) Details: <The module contains a metal shield which covers all RF components and circuitry. The shield is located on the top of the board next to antenna connector> 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with FCC requirements under conditions of excessive data rates or over-modulation. 15.212(a)(1)(ii) ☒ - YES ☐ - NO(*) Details: <Data to the modulation circuit is buffered as described in the operational description provided with the application> 3. The modular transmitter must have its own power supply regulation on the module. This is intended to ensure that the module will comply with FCC requirements regardless of the design of the power supplying circuitry in the device into which the module is installed. 15.212(a)(1)(iii) ☒ - YES ☐ - NO(*) Details: <The module contains its own power supply regulation. Please refer to schematic filed with this application> 4. The modular transmitter must comply with the antenna and transmission system requirements of §§ 15.203, 15.204(b), 15.204(c), 15.212(a), and 2.929(b). The antenna must either be permanently attached or employ a ‘‘unique’’ antenna coupler (at all connections between the module and the antenna, including the cable). The ‘‘professional installation’’ provision of § 15.203 is not applicable to modules but can apply to limited modular approvals under paragraph 15.212(b). 15.212(a)(1)(iv) ☐ - YES ☐ - NO(*) Details: <Not Applicable. Module is not a Part 15 transmitter.> 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified or commercially available (see Section 15.31(i)). 15.212(a)(1)(v) ☒ - YES ☐ - NO(*) Details: <The module was tested stand-alone as shown in test setup photographs filed with this application> 070920-02b Modular Approval Requirement Requirement Met 6. The modular transmitter must be labeled with its own FCC ID number, or use an electron display (see KDB Publication 784748). If using a permanently affixed label with its own FCC ID number, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. 15.212(a)(1)(vi) ☒ - YES ☐ - NO(*) Details: <There is a label on the module as shown in the labeling exhibit filed with this application. Host specific labeling instructions are shown in the installation manual filed with this application.> 7. The modular transmitter must comply with all specific rule or operating requirements applicable to the transmitter, including all the conditions provided in the integration instructions by the grantee. A copy of these instructions must be included in the application for equipment a…

Text truncated - open the document above for the full version.

September 6, 2023 Federal Communications Commission Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: Re: Confidentiality Request for FCC ID: N7NEM92 Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules and KDB 726920 D01 Confidentiality Request Procedures Detail, we hereby request that the exhibits listed below, submitted with our application for certification, be withheld from public disclosure. • Schematics • Block Diagram • Operation Description • Tune Up Procedure Furthermore, pursuant to Public Notice DA 04-1705 in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, we request the following exhibits be withheld from public viewing for a short limited time of 180 days from the date of the Grant of Equipment Authorization, due to the sensitive business information: • User Manual • Internal Photos • External Photos • Test Setup Photos The above exhibits contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Best Regards, Ying Wang Director, Regulatory Compliance

Top View Bottom View

EM9293 Internal Photo

TEL : 886-3-327-3456 Page : 1 of 10 FAX : 886-3-328-4978 Issued Date : Sep. 07, 2023 Form version: 220617 RF EXPOSURE EVALUATION REPORT Report No. : FA2D2006 RF EXPOSURE EVALUATION REPORT FCC ID : N7NEM92 Equipment : Wireless Module Brand Name : AirPrime Model Name : EM9293 Applicant : Sierra Wireless, ULC 13811 Wireless Way, Richmond, BC V6V 3A4 Canada Manufacturer : Sierra Wireless, ULC 13811 Wireless Way, Richmond, BC V6V 3A4 Canada Standard : 47 CFR Part 2.1091 We, SPORTON INTERNATIONAL INC has been evaluated this product in accordance with 47 CFR Part2.1091 and it complies with applicable limit. Sporton Lab is accredited to ISO 17025 by Taiwan Accreditation Foundation (TAF code: 1190) and the FCC designation No. TW1190 under the FCC 2.948(e) by Mutual Recognition Agreement (MRA) in FCC evaluation. The results in this report apply exclusively to the tested model / sample. Without written approval of SPORTON INTERNATIONAL INC. Laboratory, the test report shall not be reproduced except in full. SPORTON INTERNATIONAL INC. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City, Taiwan (R.O.C.) Approved by: Cona Huang / Deputy Manager TEL : 886-3-327-3456 Page : 2 of 10 FAX : 886-3-328-4978 Issued Date : Sep. 07, 2023 Form version: 220617 RF EXPOSURE EVALUATION REPORT Report No. : FA2D2006 Table of Contents 1. DESCRIPTION OF EQUIPMENT UNDER TEST (EUT) ............................................................................. 4 2. MAXIMUM RF AVERAGE OUTPUT POWER AMONG PRODUCTION UNITS ........................................ 5 3. DETERMINATION OF EXEMPTION ........................................................................................................... 6 4. RF EXPOSURE EVALUATION ................................................................................................................... 7 4.1. Standalone assessment .................................................................................................................... 7 4.2. Collocated assessment ..................................................................................................................... 8 TEL : 886-3-327-3456 Page : 3 of 10 FAX : 886-3-328-4978 Issued Date : Sep. 07, 2023 Form version: 220617 RF EXPOSURE EVALUATION REPORT Report No. : FA2D2006 History of this test report Report No. Version Description Issued Date FA2D2006 Rev. 01 Initial issue of report Jul. 31, 2023 FA2D2006 Rev. 02 Update section 4 Sep. 07, 2023 TEL : 886-3-327-3456 Page : 4 of 10 FAX : 886-3-328-4978 Issued Date : Sep. 07, 2023 Form version: 220617 RF EXPOSURE EVALUATION REPORT Report No. : FA2D2006 1. Description of Equipment Under Test (EUT) Product Feature & Specification EUT Type Wireless Module Brand Name AirPrime Model Name EM9293 FCC ID N7NEM92 Wireless Technology and Frequency Range WCDMA Band II: 1850 MHz ~ 1910 MHz WCDMA Band IV: 1710 MHz ~ 1755 MHz WCDMA Band V: 824 MHz ~ 849 MHz LTE Band 2: 1850 MHz ~ 1910 MHz LTE Band 4: 1710 MHz ~ 1755 MHz LTE Band 5: 824 MHz ~ 849 MHz LTE Band 7: 2500 MHz ~ 2570 MHz LTE Band 12: 699 MHz ~ 716 MHz LTE Band 13: 777 MHz ~ 787 MHz LTE Band 14: 788 MHz ~ 798 MHz LTE Band 17: 704 MHz ~ 716 MHz LTE Band 25: 1850 MHz ~ 1915 MHz LTE Band 26: 814 MHz ~ 849 MHz LTE Band 41: 2496 MHz ~ 2690 MHz LTE Band 42: 3450 MHz ~ 3550 MHz LTE Band 48: 3550 MHz ~ 3700 MHz LTE Band 66: 1710 MHz ~ 1780 MHz LTE Band 71: 663 MHz ~ 698 MHz 5G NR n2 : 1850 MHz ~ 1910 MHz 5G NR n5 : 824 MHz ~ 849 MHz 5G NR n7 : 2500 MHz ~ 2570 MHz 5G NR n12 : 699 MHz ~ 716 MHz 5G NR n13: 777 MHz ~ 787 MHz 5G NR n14 : 788 MHz ~ 798 MHz 5G NR n25 : 1850 MHz ~ 1915 MHz 5G NR n26 : 814 MHz ~ 849 MHz 5G NR n30 : 2305 MHz ~ 2315 MHz 5G NR n41 : 2496 MHz ~ 2690 MHz 5G NR n48 : 3550 MHz ~ 3700 MHz 5G NR n66 : 1710 MHz ~ 1780 MHz 5G NR n70 : 1695 MHz ~ 1710 MHz 5G NR n71 : 663 MHz ~ 698 MHz 5G NR n77: 3700 MHz ~ 3980 MHz, 3450MHz ~ 3550MHz 5G NR n78: 3700 MHz ~ 3800 MHz, 3450MHz ~ 3550MHz Mode RMC 12.2Kbps HSDPA HSUPA DC-HSDPA HSPA+ (16QAM uplink) LTE: QPSK, 16QAM, 64QAM 5G NR: DFT-s-OFDM/CP-OFDM, Pi/2 BPSK/QPSK/16QAM/64QAM/256QAM Reviewed by: Jason Wang Report Producer: Paula Chen TEL : 886-3-327-3456 Page : 5 of 10 FAX : 886-3-328-4978 Issued Date : Sep. 07, 2023 Form version: 220617 RF EXPOSURE EVALUATION REPORT Report No. : FA2D2006 2. Maximum RF average output power among production units Mode Maximum Average power(dBm) WCDMA Band 2 24.5 Band 4 24.5 Band 5 24.5 LTE Band 2 24.5 Band 4 24.5 Band 5 24.5 Band 7 24 Band 12 24 Band 13 24.5 Band 14 24 Band 17 24 Band 25 24 Band 26 24 Band 41_PC3 24 Band 41_PC2 26 Band 42_PC3 24 Band 42_PC2 26 Band 48 24 Band 66 24.5 Band 71 24 5G NR n2 25.5 n5 25.5 n7 25.5 n12 25.5 n13 25.5 n14 25.5 n25 25.5 n26 25.5 n30 25.5 n41_PC3 25.5 n41_PC2 27.5 n48 25.5 n66 25.5 n70 25.5 n71 25.5 n77_PC3 25.5 n77_PC2 27.5 n78_PC3 25.5 n78_PC2 27.5 TEL : 886-3-327-3456 Page : 6 of 10 FAX : 886-3-328-4978 Issued Date : Sep. 07, 2023 Form version: 220617 RF EXPOSURE EVALUATION REPORT Report No. : FA2D2006 3. Determination of exemption Per 1.1307(b)(3), (i) For single RF sources (i.e., any single fixed RF source, mobile device, or portable device, as defined in paragraph (b)(2) of this section): A single RF source is exempt if: (A) The available maximum time-averaged power is no more than 1 mW, regardless of separation distance. This exemption may not be used in conjunction with other exemption criteria other than those in paragraph (b)(3)(ii)(A) of this section. Medical implant devices may only use this exemption and that in paragraph (b)(3)(ii)(A); (B) Or the available maximum time-averaged power or effective radiated power (ERP), whichever is greater, is less than or equal to the threshold Pth (mW) described in the following formula. This method shall only be used at separation distances (cm) from 0.5 centimeters to 40 centimeters and at frequencies from 0.3 GHz to 6 GHz (inclusive). Pth is given by: (C) Or using Table 1 and the minimum separation distance (R in me…

Text truncated - open the document above for the full version.

TEL : 886-3-327-0868 Page Number : 1 of 10 FAX : 886-3-327-0855 Issue Date : Sep. 07, 2023 Report Template No.: BU5-FGLTE96.47 Version 2.0 Report Version : 01 FCC RADIO TEST REPORT Report No. : FG2D2006D FCC Part 96.47 TEST REPORT FCC ID : N7NEM92 Equipment : Wireless Module Brand Name : AirPrime Model Name : EM9293 Applicant : Sierra Wireless, ULC 13811 Wireless Way, Richmond, BC V6V 3A4 Canada Manufacturer : Sierra Wireless, ULC 13811 Wireless Way, Richmond, BC V6V 3A4 Canada Standard : FCC Part 96.47 RF Interface : LTE B48 The product was received on Jun. 26, 2023, and testing was performed from Jul. 03, 2023 to Jul. 03, 2023. We, Sporton International Inc. Wensan Laboratory, would like to declare that the tested sample has been evaluated in accordance with the test procedures and has been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval from Sporton International Inc. Wensan Laboratory, the test report shall not be reproduced except in full. Approved by: Jones Tsai Sporton International Inc. Wensan Laboratory No.58, Aly. 75, Ln. 564, Wenhua 3rd, Rd., Guishan Dist., Taoyuan City 333010, Taiwan (R.O.C.) TEL : 886-3-327-0868 Page Number : 2 of 10 FAX : 886-3-327-0855 Issue Date : Sep. 07, 2023 Report Template No.: BU5-FGLTE96.47 Version 2.0 Report Version : 01 FCC RADIO TEST REPORT Report No. : FG2D2006D Table of Contents History of this test report ................................................................................................................................. 3 Summary of Test Result................................................................................................................................... 4 1 General Description ................................................................................................................................... 5 1.1 Product Feature of Equipment Under Test ........................................................................................ 5 1.2 Modification of EUT ........................................................................................................................... 5 1.3 Testing Location ................................................................................................................................ 5 1.4 Applicable Standards ......................................................................................................................... 5 2 Test Configuration of Equipment Under Test ......................................................................................... 6 2.1 Connection Diagram of Test System ................................................................................................. 6 3 End User Device additional requirement ................................................................................................. 7 3.1 Test Requirement .............................................................................................................................. 7 3.2 Test Procedure .................................................................................................................................. 7 3.3 Test Result ......................................................................................................................................... 8 4 List of Measuring Equipment .................................................................................................................. 10 TEL : 886-3-327-0868 Page Number : 3 of 10 FAX : 886-3-327-0855 Issue Date : Sep. 07, 2023 Report Template No.: BU5-FGLTE96.47 Version 2.0 Report Version : 01 FCC RADIO TEST REPORT Report No. : FG2D2006D History of this test report Report No. Version Description Issue Date FG2D2006D 01 Initial issue of report Sep. 07, 2023 TEL : 886-3-327-0868 Page Number : 4 of 10 FAX : 886-3-327-0855 Issue Date : Sep. 07, 2023 Report Template No.: BU5-FGLTE96.47 Version 2.0 Report Version : 01 FCC RADIO TEST REPORT Report No. : FG2D2006D Summary of Test Result Report Clause Ref Std. Clause Test Items Result (PASS/FAIL) Remark 3 96.47 End User Device additional requirement Pass - Conformity Assessment Condition: The test results (PASS/FAIL) with all measurement uncertainty excluded are presented against the regulation limits or in accordance with the requirements stipulated by the applicant/manufacturer who shall bear all the risks of non-compliance that may potentially occur if measurement uncertainty is taken into account. Disclaimer: The product specifications of the EUT presented in the test report that may affect the test assessments are declared by the manufacturer who shall take full responsibility for the authenticity. Reviewed by: Thomas Chen Report Producer: Clio Lo TEL : 886-3-327-0868 Page Number : 5 of 10 FAX : 886-3-327-0855 Issue Date : Sep. 07, 2023 Report Template No.: BU5-FGLTE96.47 Version 2.0 Report Version : 01 FCC RADIO TEST REPORT Report No. : FG2D2006D 1 General Description 1.1 Product Feature of Equipment Under Test Product Feature General Specs WCDMA/LTE/5G NR, and GNSS. Remark: 1. The EUT's information above is declared by manufacturer. Please refer to Disclaimer in report summary. 2. The maximum allowable antenna gain is determined by the manufacturer. 1.2 Modification of EUT No modifications made to the EUT during the testing. 1.3 Testing Location Test Site Sporton International Inc. Wensan Laboratory Test Site Location No.58, Aly. 75, Ln. 564, Wenhua 3rd, Rd., Guishan Dist., Taoyuan City 333010, Taiwan (R.O.C.) TEL: +886-3-327-0868 FAX: +886-3-327-0855 Test Site No. Sporton Site No. TH05-HY Test Engineer Thomas Chen Temperature 22 ~ 25 °C Relative Humidity 41 ~ 45 % FCC designation No.: TW3786 1.4 Applicable Standards  FCC Part 96.47  FCC KDB 940660 D01 Part 96 CBRS Eqpt v03  WINNF-TS-0122-V1.0.2 CBRS CBSD Test Specification Remark: 1. All test items were verified and recorded according to the standards …

Text truncated - open the document above for the full version.

TEL : 886-3-327-3456 Page Number : 1 of 22 FAX : 886-3-328-4978 Issue Date : Sep. 07, 2023 Report Template No.: BU5-FGLTE96 Version 2.4 Report Version : 01 FCC RADIO TEST REPORT Report No. : FG2D2006F FCC RADIO TEST REPORT FCC ID : N7NEM92 Equipment : Wireless Module Brand Name : AirPrime Model Name : EM9293 Applicant : Sierra Wireless, ULC 13811 Wireless Way, Richmond, BC V6V 3A4 Canada Manufacturer : Sierra Wireless, ULC 13811 Wireless Way, Richmond, BC V6V 3A4 Canada Standard : FCC 47 CFR Part 2, 96 The product was received on Mar. 10, 2023 and testing was performed from Mar. 26, 2023 to Jul. 13, 2023. We, Sporton International Inc. EMC & Wireless Communications Laboratory, would like to declare that the tested sample has been evaluated in accordance with the test procedures given in ANSI / TIA-603-E and has been in compliance with the applicable technical standards. The test results in this report apply exclusively to the tested model / sample. Without written approval of Sporton International Inc. EMC & Wireless Communications Laboratory, the test report shall not be reproduced except in full. Approved by: Louis Wu Sporton International Inc. EMC & Wireless Communications Laboratory No. 52, Huaya 1st Rd., Guishan Dist., Taoyuan City …

Text truncated - open the document above for the full version.