N7NHL78CRadio Module

Sierra Wireless HL781x Product Technical Specification 41114133 Rev. 5 Product Technical Specification Rev. 5 October 2022241114133 Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless product are used in a normal manner with a well-constructed network, the Sierra Wireless product should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless product, or for failure of the Sierra Wireless product to transmit or receive such data. Safety and Hazards Do not operate the Sierra Wireless product in areas where blasting is in progress, where explosive atmospheres may be present, near medical equipment, near life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the Sierra Wireless product MUST BE POWERED OFF. The Sierra Wireless product can transmit signals that could interfere with this equipment. Do not operate the Sierra Wireless product in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless product MUST BE POWERED OFF. When operating, the Sierra Wireless product can transmit signals that could interfere with various onboard systems. Note:Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless products may be used at this time. The driver or operator of any vehicle should not operate the Sierra Wireless product while in control of a vehicle. Doing so will detract from the driver or operator’s control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence. Limitation of Liability The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY. Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product. PatentsThis product may contain technology developed by or for Sierra Wireless Inc. This product includes technology licensed from QUALCOMM ® . This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents licensed from MMP Portfolio Licensing. Preface Rev. 5 October 2022341114133 Copyright© 2022 Sierra Wireless. All rights reserved. TrademarksSierra Wireless ® , AirLink ® , AirVantage ® and the Sierra Wireless logo are registered trademarks of Sierra Wireless. Windows ® and Windows Vista ® are registered trademarks of Microsoft Corporation. Macintosh ® and Mac OS X ® are registered trademarks of Apple Inc., registered in the U.S. and other countries. QUALCOMM ® is a registered trademark of QUALCOMM Incorporated. Used under license. Other trademarks are the property of their respective owners. Contact Information Revision History Sales information and technical support, including warranty and returns Web: sierrawireless.com/company/contact-us/ Global toll-free number: 1-877-687-7795 6:00 am to 5:00 pm PST Corporate and product informationWeb: sierrawireless.com Revision number Release dateChanges 1.0June 2021Creation 2.0May 2022Updated: •Current consumption values 3.0May 2022Added: •Taiwan NCC Statement Product Technical Specification Rev. 5 October 2022441114133 4.0September 2022Updated: •Table3-7, Table3-8, Table3-9, Table4-10 values •Table3-9 changed to Cat-NB •For Table3-14 : •NB1 UL peak throughput value changed from 62.5 to 45.7 •Subcarriers uplink changed from 3 to 12 •For Table3-15 •Changed HL7810 to HL7812 •Removed duplicate MCS.TBS:13 •Changed NB2 UL peak throughput from 109 kbps to 159 kbps •Changed Subcarriers uplink from 3 to 12 •Table8-1 and Table8-2 values Added: •Added Standby for Table3-6, Table3-7, Table3-8, Table3-9 •Added note for flash wear out feature under Table3-5 5.0October 2022Updated: •Table8-1 Band 8 Added: •Added RF Circuit Rev 5 October 2022541114133 Contents 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 1.1 Supported RF Bands/Connectivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 1.2 Common Flexible Form Factor (CF3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 1.3 Physical Dimensions and Connection Interface . . . . . . . . . . . . . . . . . . . . . . . . . . .10 1.4 General Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 1.5 Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 1.6 Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1…

Text truncated - open the document above for the full version.

Limited Modular Approval Checklist FCC ID: N7NHL78C Item Requirements EUT 1 The radio elements must have the radio frequency circuitry shielded Module RADIO elements are shielded. Please see submitted external photograph exhibits 2 The module must have buffered modulation/data inputs Module chipset design incorporates integrated buffer circuitry 3 The module must contain power supply regulation on the module Module chipset incorporates voltage regulation to transceiver circuitry 4 The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s) No applicable to licensed modules 5 The module must demonstrate compliance in a stand-alone configuration EUT conformance testing was performed in a standalone configuration 6 The licensed module must have a FCC ID label on the module itself. That FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text: Contains “FCC ID: N7NHL78C” Please refer to FCC ID label format. Labeling instruction has been provided in the user manual exhibit(s). 7 The module must comply with all specific rules applicable to the transmitter. The grantee must provide comprehensive instructions to explain compliance requirements The Module is compliant with all applicable FCC rules. Compliance requirements are stated in the user manual exhibit(s). 8 The module must comply with RF exposure requirements Compliance with RF exposure requirements is addressed in RF exposure report Sincerely, __________________________ By: Denis CHABOT Title: Director, Certification Company: Sierra Wireless Inc. Telephone: +852 2824 5222 e-mail: [email protected]

September 7, 2016 Federal Communications Commission Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 RE: Authorization Letter for Grantee Code N7N Dear Sir/Madam: I hereby authorize Mr. Denis Chabot of Sierra Wireless to act on my behalf in all manners relating to the application for equipment authorization including signing of all documents relating to these matters. Any and all acts carried out by Mr. Denis Chabot of Sierra Wireless on my behalf shall have the same effect as acts of my own. Sincerely, Ying Wang Manager, Regulatory Compliance

September 20, 2022 Federal Communications Commission Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: Re: Confidentiality Request for FCC ID: N7NHL78C Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules and KDB 726920 D01 Confidentiality Request Procedures Detail, we hereby request that the exhibits listed below, submitted with our application for certification, be withheld from public disclosure. • Schematics • Block Diagram • Operation Description • Tune Up Procedure The above exhibits contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Furthermore, pursuant to Public Notice DA 04-1705 in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, we request the following exhibits be withheld from public viewing for a short limited time of 180 days from the date of the Grant of Equipment Authorization, due to the sensitive business information: • User Manual • Internal Photos Best Regards, Denis CHABOT Director, Certification

Justification of test data reuse (HL7812) October 18 th , 2022 2 Comparison • Model Name: HL7802 • FCC ID: N7NHL7802IC: 2417C-HL7802 • Supported Frequency bands • Cat-M1/NB1: B1, B2, B3, B4, B5, B8, B9, B10, B12, B13, B17, B18, B19, B20, B25, B26, B27, B28, B66 • 2G: 850, 1900 • Model Name: HL7812 • FCC ID: N7NHL78C IC: 2417C-HL78C • Supported Frequency bands • Cat-M1/NB1/NB2: B1, B2, B3, B4, B5, B8, B12, B13, B18, B19, B20, B25, B26, B28, B66, B85 • 2G: 850, 1900 • B8 is covering the range as defined in Part 27 SubPart P • NB2 is supported through a FW upgrade – no impact 3 Comparison (continued) • Both modules have the same form factor, I/O interface, shielding and antenna connectors. • Schematics: – Both modules share the same schematics including BOM – Band 8 was already supported in the original product – Band 85 is enabled by FW, no change in HW required • PCB Layout: – Both modules use a closely similar PCB, with some passive (resistors/capacitors) as well as the memory (U203) and crystal (OSC400) updated to accommodate those components end-of-life. – Performances of the 2 devices are identical 4 Layout (HL7802/HL7812) 5 Layout (HL7802/HL7812) 6 Module RF Trace • RF Traces for HL7802 and HL7812 are 100% identical HL7802 RF TraceHL7812 RF Trace 7 RF Trace design (HL7802/HL7812) • RF Traces for HL7802 and HL7812 are 100% identical as the development kit used is the same HL7802 dev kit RF TraceHL7812 dev kit RF Trace 8 RF Results • The components in HL7812 design are identical to HL7802’s in terms of characteristics. • The RF performance of HL7802 and HL7812 are identical with the exception that the HL7812 modules includes additional support for Band 85 (Band 8 was already supported in HL7802 as per 3GPP, not as per FCC Part 27). – Worst case testing (based on HL7802 results) was performed on HL7812 and all results are within the max tolerances set forth in the product specification • All test data of HL7802 per FCC Part 22, 24, 27 and 90 as well as RSS-130, RSS-132, RSS- 133 and RSS0139 are valid for the HL7812 module. • All reports are available in original certification under N7NHL7802 (FCC) and 2417C-HL7802 (ISED) • Test data for Band 8 and Band 85 are provided as tested against HL7812. • As such, LTE results from HL7802 can be reused for the FCC/IC certification of HL7812 Thank you 13811 Wireless Way :: Richmond, British Columbia, Canada, V6V 3A4 sierrawireless.com

053019-02a OEM Integration Manual Guidance – KDB 996369 D03 Section 2 Clear and Specific Instructions Describing the Conditions, Limitations, and Procedures for third-parties to use and/or integrate the module into a host device. Requirement Is this module intended for sale to third parties? ☒ - YES ☐ - No, If No, and LMA applies, the applicant can optionally choose to not make the following detailed info public. However there still needs to be basic integration instructions for a users manual and the information below must still be included in the operational description. If the applicant wishes to keep this info confidential, this will require a separate statement cover letter explaining the module is not for sale to third parties and that integration instructions are internal confidential documents. Items required to be in the manual – See KDB 996369 D03, Section 2 As of May 1, 2019, the FCC requires ALL the following information to be in the installation manual. Modular transmitter applicants should include information in their instructions for all these items indicating clearly when they are not applicable. For example information on trace antenna design could indicate “Not Applicable”. Also if a module is limited to only a grantees own products and not intended for sale to third parties, the user instructions may not need to be detailed and the following items can be placed in the operational description, but this should include a cover letter as cited above. 1. List of applicable FCC rules. KDB 996369 D03, Section 2.2 a. Only list rules related to the transmitter. ☒ - All Items shown to the left are provided in the Modular Integration Guide (or UM) for Full Modular Approval (MA) or LMA. ☐ - An LMA applies and is approved ONLY for use by the grantee in their own products, and not intended for sale to 3 rd parties as provided in a separate cover letter. Therefore the information shown to the left is found in the theory of operation. 2. Summarize the specific operational use conditions. KDB 996369 D03, Section 2.3 a. Conditions such as limits on antennas, cable loss, reduction of power for point to point systems, professional installation info 3. Limited Module Procedures. KDB 996369 D03, Section 2.4 a. Describe alternative means that the grantee uses to verify the host meets the necessary limiting conditions b. When RF exposure evaluation is necessary, state how control will be maintained such that compliance is ensured, such as Class II for new hosts, etc. 4. Trace antenna designs. KDB 996369 D03, Section 2.5 a. Layout of trace design, parts list, antenna, connectors, isolation requirements, tests for design verification, and production test procedures for ensuring compliance. If confidential, the method used to keep confidential must be identified and information provided in the operational description. 5. RF exposure considerations. KDB 996369 D03, Section 2.6 a. Clearly and explicitly state conditions that allow host manufacturers to use the module. Two types of instructions are necessary: first to the host manufacturer to define conditions (mobile, portable – xx cm from body) and second additional text needed to be provided to the end user in the host product manuals. 6. Antennas. KDB 996369 D03, Section 2.7 a. List of antennas included in the application and all applicable professional installer instructions when applicable. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc – note that “omni-directional” is not considered a type) 7. Label and compliance information. KDB 996369 D03, Section 2.8 a. Advice to host integrators that they need to provide a physical or e-label stating “Contains FCC ID: N7NHL78C“ with their finished product 8. Information on test modes and additional testing requirements. KDB 996369 D03, Section 2.9 a. Test modes that should be taken into consideration by host integrators including clarifications necessary for stand-alone and simultaneous configurations. b. Provide information on how to configure test modes for evaluation 9. Additional testing, Part 15 Subpart B disclaimer. KDB 996369 D03, Section 2.10 Sincerely, By: DIRECTOR, CERTIFICATION DENIS CHABOT (Signature/Title 1 ) (Print name) 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

HL7812 – Internal photos

MPE Evaluation for HL7812 Radio Module May 20, 2022 Contents 1. Introduction..................................................................................................... 2 2. RF Exposure Limits and Equations ................................................................ 3 3. Stand-Alone Transmission ............................................................................. 5 4. Collocated Transmission ................................................................................ 7 5. Conclusion...................................................................................................... 8 1. Introduction In this application we seek modular approval for the HL7812 radio module for use in standalone and collocated simultaneous transmission under mobile and fixed configurations. This Maximum Permissive Exposure (MPE) report demonstrates compliance analysis for HL7812 radio module with FCC CFR 47 §2.1091 and IC RSS-102 for standalone and collocated transmission in the exposure conditions where a separation distance of at least 20 centimeters is normally maintained between the transmitter's radiating structure(s) and the body of the user or nearby persons. The MPE analysis is limited for US / Canada bands only. The general population/uncontrolled exposure limits are applicable to situations in which the general public may be exposed or in which persons who are exposed as a consequence of their employment may not be made fully aware of the potential for exposure or cannot exercise control over their exposure. 2. RF Exposure Limits and Equations FCC Limits: According to FCC OET Bulletin 65 Supplement C, the criteria listed in Table 1 shall be used to evaluate the environmental impact of human exposure to radio frequency (RF) radiation as specified in §1.1307. Table 1 : Limits for Maximum Permissible Exposure (MPE) IC Limits: IC has adopted the RF field strength limits established in Health Canada’s RF exposure guideline. The limits are shown in Table 2 below per RSS- 102. Table 2 : RF Field Strength Limits for Devices Used by the General Public (Uncontrolled Environment) In the frequency range of 300-6000 MHz, the IC limits are more stringent than the FCC limits. The MPE evaluation in this report will be based on the IC limits, so the deduced output power and antenna gain limits will guarantee compliance with both FCC and IC requirements. EQUATIONS: EIRP (dBm) = Conducted Power (dBm) + Antenna Gain (dBi) Power density is given by : S = EIRP / (4 π * D^2) where S = Power density (mW/cm^2) EIRP = Equivalent Isotropic Radiated Power (mW) D = Separation distance (cm) 3. HL7812 Product Specifications HL7812 will transmit on only one band and mode of operation at any one time. Table 3 lists the supported frequency bands in Canada/USA and the maximum power in each of those bands. Operating Mode Operating Mode TX Freq Range (MHz) Max Time-Avg Cond Power (dBm) GPRS GPRS G850 824 849 33.5 GPRS G1900 1850 1910 30.5 LTE CAT-M1/NB2 LTE Band 2 1850 1910 24.5 LTE Band 4 1710 1755 24.5 LTE Band 5 824 849 24.5 LTE Band 8 897.5 900.5 24.5 LTE Band 12 699 716 24.5 LTE Band 13 777 787 24.5 LTE Band 25 1850 1915 24.5 LTE Band 26 814 849 24.5 LTE Band 66 1710 1780 24.5 LTE Band 66 698 716 24.5 Table 3: HL7812 Frequency Bands and Output Power 4. Stand-Alone Transmission When HL7812 module transmits as a stand-alone mobile device, the source- based time-averaged EIRP is calculated by summing up conducted power and antenna gain. A 100% duty cycle is used for calculations in LTE mode to present a worse-case analysis. The actual duty cycle is much smaller. A 25% duty cycle is used for calculations in GPRS mode to present a worse-case analysis. The actual duty cycle is much smaller. The antenna gains are chosen so that the resulted radiated power levels are within the limits specified by the FCC rules and IC Radio Standards Specifications (RSS). The IC exemption limits for routine RF exposure evaluation are calculated using the lowest frequency of the operating band presenting the most stringent limits. As shown in Table 2 below, the resulted EIRP are always below the IC exemption limits for all the operating modes. Operating Mode Frequency (MHz) Maximum Power (dBm) Antenna Gain (dBi) Maximum EIRP (dBm) Power Density @20 cm (mW/cm^2) IC Limit (mW/cm2) GPRS G850 824 849 33.5 3 36.5 0.222 0.258 GPRS G1900 1850 1910 30.5 2 32.5 0.088 0.448 LTE Band 2 1850 1910 24.5 6 30.5 0.223 0.448 LTE Band 4 1710 1755 24.5 5.5 30 0.199 0.424 LTE Band 5 824 849 24.5 6 30.5 0.223 0.258 LTE Band 8 897.5 900.5 24.5 6 30.5 0.223 0.273 LTE Band 12 699 716 24.5 6 30.5 0.223 0.23 LTE Band 13 777 787 24.5 6 30.5 0.223 0.247 LTE Band 25 1850 1915 24.5 6 30.5 0.223 0.448 LTE Band 26 814 849 24.5 6 30.5 0.223 0.255 LTE Band 66 1710 1780 24.5 5.5 30 0.199 0.424 LTE Band 85 698 716 24.5 6 30.5 0.223 0.23 Table 2: HL7812 Stand-Alone Transmission 5. Collocated Transmission When HL7812 module co-transmits with radio transmitter(s) as a mobile device, per KDB 447498 D01, simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on the calculated/estimated, numerically modeled or measured field strengths or power density, is ≤ 1.0. The evaluation here considers a WLAN transmitter, a Bluetooth transmitter and a WiGig transmitter as collocated transmitters. Their radiated output power levels are listed in Table 3 below. The MPE ratio is defined by the ratio of power density to MPE limit. The sum of the MPE ratios is calculated as follows: ∑푀푃퐸 푅푎푡푖표 = Max (HL7812 MPE ratio) + Max (WLAN MPE ratio) + BT MPE Ratio = 0.612+0.372+0.015+0.063=0.999 < 1.0 Operating Mode Frequency (MHz) Maximum Power (dBm) Antenna Gain (dBi) Maximum EIRP (dBm) Power Density @20 cm (mW/cm^2) Limit (mW/cm2) Power Density / Limit GPRS G850 824 849 33.5 1 34.5 0.140 0.258 0.544 GPRS G1900 1850 1910 30.5 2 32.5 0.088 0.448 0.198 LTE Band 2 1850 1910 24.5 6 30.5 …

Text truncated - open the document above for the full version.

Report No.：2230599R-RFNAOTHV02-B TEL : +886-3-582-8001 Page Number : 1 of 16 FAX : +886-3-582-8958 Issued Date : Sep. 30, 2022 Report Version : V1.0 FCC/ISED Test Report Product Name ： Module Brand Name ： AirPrime Model No. ： HL7812 FCC ID ： N7NHL78C IC ： 2417C-HL78C Applicant ： Sierra Wireless, Inc. Address ： 13811 Wireless Way, Richmond, BC V6V 3A4, Canada Date of Receipt ： Mar. 16, 2022 Issued Date ： Sep. 30, 2022 Report No. ： 2230599R-RFNAOTHV02-B Report Version ： V1.0 The test results relate only to the samples tested. The test results shown in the test report are traceable to the national/international standard through the calibration of the equipment and evaluated measurement uncertainty herein. This report must not be used to claim product endorsement by TAF or any agency of the government. Measurement uncertainties evaluated for each testing system and associated connections are given here to provide the system information for reference. Compliance determinations do not take into account measurement uncertainties for each testing system, but are based on the results of the compliance measurement. The test report shall not be reproduced except in full without the written approval of DEKRA Testing and Certification Co., Ltd. Report No.：2230599R-RFNAOTHV02-B TEL : +886-3-582-8001 Page Number : 2 of 16 FAX : +886-3-582-8958 Issued Date : Sep. 30, 2022 Report Version : V1.0 Product Name : Module Applicant : Sierra Wireless, Inc. Address : 13811 Wireless Way, Richmond, BC V6V 3A4, Canada Manufacturer : Sierra Wireless, Inc. Address : 13811 Wireless Way, Richmond, BC V6V 3A4, Canada Brand Name : AirPrime Model No. : HL7812 FCC ID : N7NHL78C IC : 2417C-HL78C EUT Voltage : DC 2.8~4.35V (host equipment) Testing Voltage : DC 3.7V Applicable Standard : FCC CFR Title 47 Part 22 Subpart H FCC CFR Title 47 Part 24 Subpart E RSS-132 Issue 3 RSS-133 Issue 6 RSS-Gen Issue 5 ANSI/TIA-603-E-2016 ANSI C63.26-2015 Laboratory Name : DEKRA Testing and Certification Co., Ltd. Hsin Chu Laboratory Address : No.372-2, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 310, Taiwan, R.O.C. Test Result : Complied Documented By : ( Hailey Peng / Senior Engineer ) Approved By : ( Rueyyan Lin / Supervisor ) The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of DEKRA Testing and Certification Co., Ltd. Report No.：2230599R-RFNAOTHV02-B TEL : +886-3-582-8001 Page Number : 3 of 16 FAX : +886-3-582-8958 Issued Date : Sep. 30, 2022 Report Version : V1.0 Revision History Version Description Issued Date V1.0 Initial issue of report Sep. 30, 2022 Report No.：2230599R-RFNAOTHV02-B TEL : +886-3-582-8001 Page Number : 4 of 16 FAX : +886-3-582-8958 Issued Date : Sep. 30, 2022 Report Version : V1.0 TABLE OF CONTENTS Description Page 1. General Information ....................................................................................................................................... 5 1.1. EUT Description ............................................................................................................................................. 5 1.2. Mode of Operation ......................................................................................................................................... 6 1.3. Comments and Remarks .............................................................................................................................. 6 1.4. Tested System Details .................................................................................................................................. 7 1.5. Configuration of Tested System .................................................................................................................. 7 1.6. EUT Operation of during Test ...................................................................................................................... 7 2. Technical Test .................................................................................................................................................. 8 2.1. Summary of Test Result................................................................................................................................ 8 2.2. Test Facility ...................................................................................................................................................... 9 2.3. List of Test Equipment ................................................................................................................................. 10 2.4. Measurement Uncertainty .......................................................................................................................... 10 3. Spurious Emission ....................................................................................................................................... 11 3.1. Te s t Setup ...................................................................................................................................................... 11 3.2. Test Procedure .............................................................................................................................................. 12 3.3. Test Methodology and Reference Procedures ...................................................................................... 12 3.4. Te s t Result of Radiated Spurious Emission ........................................................................................... 13 Appendix A .................................................................................................................................................................. 15  Test Setup Photograph ............................................................................................................................... 15 Report No.：2230599R-RFNAOTHV02-B TEL : +886-3-582-8001 Page Number : 5 of 16 FAX : +886-3-582-8958 Issued Date : Sep. 30, 2022 Repo…

Text truncated - open the document above for the full version.

Report No.：2230599R-RFUSOTHV13-B TEL : +886-3-582-8001 Page Number : 85 of 110 FAX : +886-3-582-8958 Issued Date : Sep. 30, 2022 Report Version : V3.0 Mode 20: NB-IoT Band 26 (Part 22) Report No.：2230599R-RFUSOTHV13-B TEL : +886-3-582-8001 Page Number : 86 of 110 FAX : +886-3-582-8958 Issued Date : Sep. 30, 2022 Report Version : V3.0 Mode 21: NB-IoT Band 26 (Part 90) Report No.：2230599R-RFUSOTHV13-B TEL : +886-3-582-8001 Page Number : 87 of 110 FAX : +886-3-582-8958 Issued Date : Sep. 30, 2022 Report Version : V3.0 Mode 22: NB-IoT Band 66 Report No.：2230599R-RFUSOTHV13-B TEL : +886-3-582-8001 Page Number : 88 of 110 FAX : +886-3-582-8958 Issued Date : Sep. 30, 2022 Report Version : V3.0 7. Conducted Band Edge 7.1. Test Setup 7.2. Test Procedure 1. The EUT makes a call to the communication simulator. The communication simulator station system controlled a EUT to export maximum output power under transmission mode and specific channel frequency. The path loss was compensated to the results for each measurement. 2. In the 1MHz bands immediately outside and adjacent to the frequency block a resolution bandwidth of at least one percent of the emission bandwidth of the fundamental emission of the transmitter may be employed to measure the out of band Emissions. 7.3. Test Methodology and Reference Procedures KDB 971168 D01 Power Meas License Digital Systems v03r01 ANSI C63.26-2015 Communication Simulator Power Splitter Spect…

Text truncated - open the document above for the full version.