N7NMC7350Wireless Module

4114814 1.1 November 19, 2013 AirPrime MC7350 Hardware Integration Guide 4114814 Rev 1.1 November 19, 2013 2 Hardware Integration Guide Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data. Safety and Hazards Do not operate the Sierra Wireless modem in areas where cellular modems are not advised without proper device certifications. These areas include environments where cellular radio can interfere such as explosive atmospheres, medical equipment, or any other equipment which may be susceptible to any form of radio interference. The Sierra Wireless modem can transmit signals that could interfere with this equipment. Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard systems. Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless modems may be used at this time. The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of a vehicle. Doing so will detract from the driver or operator’s control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence. Limitations of Liability This manual is provided “as is”. Sierra Wireless makes no warranties of any kind, either expressed or implied, including any implied warranties of merchantability, fitness for a particular purpose, or noninfringement. The recipient of the manual shall endorse all risks arising from its use. The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY. Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product. Customer understands that Sierra Wireless is not providing cellular or GPS (including A-GPS) services. These services are provided by a third party and should be purchased directly by the Customer. 4114814 Rev 1.1 November 19, 2013 3 Hardware Integration Guide SPECIFIC DISCLAIMERS OF LIABILITY: CUSTOMER RECOGNIZES AND ACKNOWLEDGES SIERRA WIRELESS IS NOT RESPONSIBLE FOR AND SHALL NOT BE HELD LIABLE FOR ANY DEFECT OR DEFICIENCY OF ANY KIND OF CELLULAR OR GPS (INCLUDING A-GPS) SERVICES. Patents This product may contain technology developed by or for Sierra Wireless Inc. This product includes technology licensed from QUALCOMM ® . This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents licensed from InterDigital Group and MMP Portfolio Licensing. Copyright © 2013 Sierra Wireless. All rights reserved. Trademarks Sierra Wireless ® , AirPrime ® , AirLink ® , AirVantage ® , WISMO ® and the Sierra Wireless and Open AT logos are registered trademarks of Sierra Wireless, Inc. or one of its subsidiaries. Watcher ® is a registered trademark of NETGEAR, Inc., used under license. Windows ® and Windows Vista ® are registered trademarks of Microsoft Corporation. Macintosh ® and Mac OS X ® are registered trademarks of Apple Inc., registered in the U.S. and other countries. QUALCOMM ® is a registered trademark of QUALCOMM Incorporated. Used under license. Other trademarks are the property of their respective owners. Contact Information Sales Desk: Phone: 1-604-232-1488 Hours: 8:00 AM to 5:00 PM Pacific Time Contact: http://www.sierrawireless.com/sales Post: Sierra Wireless 13811 Wireless Way Richmond, BC Canada V6V 3A4 Technical Support: [email protected] RMA Support: [email protected] Fax: 1-604-231-1109 Web: http://www.sierrawireless.com/ Consult our website for up-to-date product descriptions, documentation, application notes, firmware upgrades, troubleshooting tips, and press releases: www.sierrawireless.com 4114814 Rev 1.1 November 19, 2013 4 Hardware Integration Guide Document History Version Date Updates 1.0 October 30, 2013 Creation 1.1 November 19, 2013 Updated section 5.3 Important Compliance Information for North American Users 4114814 Rev 1.1 November 19, 2013 5 Contents 1. INTRODUCTION .................................................................................................. 7 1.1. Hardware Development Components ............................................................................... 7 2. POWER INTERFACE ...…

Text truncated - open the document above for the full version.

Date: November 15 th , 2013 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: Re: Confidentiality Request for FCC ID: N7NMC7350 We hereby request that the exhibits listed below, submitted with our application for certification, be withheld from public disclosure. This request is made under the provisions of Section 0.457(d) and 0.459 of the Commission’s Rules, and Section 522(b)(4) of the Freedom of Information Act. We cite trade secrets as the reason and purpose of the request. Schematics Block Diagram Operation Description Tune Up Procedure Furthermore, pursuant to Public Notice DA 04-1705 in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, we request the following exhibits be withheld from public viewing for a short limited time of 180 days from the date of the Grant of Equipment Authorization, due to the sensitive business information: Integration Manual Product Photos Test Setup Photos Best Regards, Suzi Lan Approval Certification Engineer

Modular Approval Checklist FCC ID: Item Requirements EUT 1 The radio elements must have the radio frequency circuitry shielded Module RADIO elements are shielded. Please see submitted external photograph exhibits 2 The module must have buffered modulation/data inputs Module chipset design incorporates integrated buffer circuitry 3 The module must contain power supply regulation on the module Module chipset incorporates voltage regulation to transceiver circuitry 4 The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s) No applicable to licensed modules 5 The module must demonstrate compliance in a stand-alone configuration EUT conformance testing was performed in a standalone configuration 6 The licensed module must have a FCC ID label on the module itself. That FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text: Contains “FCC ID: N7NSL8084G Please refer to FCC ID label format. Labeling instruction has been provided in the user manual exhibit(s). 7 The module must comply with all specific rules applicable to the transmitter. The grantee must provide comprehensive instructions to explain compliance requirements The Module is compliant with all applicable FCC rules. Compliance requirements are stated in the user manual exhibit(s). 8 The module must comply with RF exposure requirements Compliance with RF exposure requirements is addressed in RF exposure report SL8084T N7NMC7350 MC7350"

Sierra Wireless Inc., 13811 Wireless Way Richmond, BC Canada V6V 3A4 Tel. +1 604 231 1100 Fax. +1 604 231 1109 Date: November 15, 2013 Model # MC7350 FCC ID: N7NMC7350 IC: 2417C-MC7350 Device Photos: Enclosure, Top Surface Enclosure, Bottom Surface Disclosure:

Sierra Wireless Inc., 13811 Wireless Way Richmond, BC Canada V6V 3A4 Tel. +1 604 231 1100 Fax. +1 604 231 1109 Date: November 15, 2013 Model # MC7350 FCC ID: N7NMC7350 IC: 2417C-MC7350 Label and location:

Sierra Wireless Inc., 13811 Wireless Way Richmond, BC Canada V6V 3A4 Tel. +1 604 231 1100 Fax. +1 604 231 1109 Date: November 15, 2013 Model # MC7350 FCC ID: N7NMC7350 IC: 2417C-MC7350 Device Photos: Enclosure, Top Surface Enclosure, Bottom Surface Disclosure:

MPE Evaluation for MC7350 Wireless Module November 15, 2013 1. Introduction In this application we seek for modular approval to the MC7350 wireless module for use in standalone and collocated simultaneous transmission under mobile configuration. This Maximum Permissive Exposure (MPE) report demonstrates compliance analysis for MC7350 wireless module with FCC CFR 47 §2.1091 and IC RSS-102 for standalone and collocated transmission in mobile exposure conditions. The MPE analysis is limited for US / Canada bands only. The general population/uncontrolled exposure limits are applicable to situations in which the general public may be exposed or in which persons who are exposed as a consequence of their employment may not be made fully aware of the potential for exposure or cannot exercise control over their exposure. Any collocated transmitter must have a valid FCC ID documenting equivalent or degraded RF characteristics with the collocated parameters defined in this MPE report. A separation distance of 20cm or more shall be maintained between the end user and each WWAN, WiMAX or WLAN, and Bluetooth transmitting antenna. Portable user conditions or additional collocated transmitters not allowed based on this RF exposure analysis require a Class II permissive change and updated RF exposure report. 2. RF Exposure Limits and Equations FCC RULES: According to FCC OET Bulletin 65 Supplement C, the criteria listed in Table 1 shall be used to evaluate the environmental impact of human exposure to radio frequency (RF) radiation as specified in §1.1307. Table 1 : Limits for Maximum Permissible Exposure (MPE) IC RULES: IC has adopted the RF field strength limits established in Health Canada’s RF exposure guideline. The limits are shown in Table 2 below per RSS 102. Table 2 : RF Field Strength Limits for Devices Used by the General Public (Uncontrolled Environment) EQUATIONS: Power density is given by : S = EIRP /(4 * Pi* D^2) where S = Power density (mW/cm^2) EIRP = Equivalent Isotropic Radiated Power (mW) D = Separation distance (cm) 3. Product Declarations The MC7350 wireless module can be installed for use in any mobile host as long as the antenna gain of the host antenna does not exceed the gain listed in table 3. This MPE analysis is applicable to any collocated transmitters with transmit power: -less than or equal to 29.0dBm for WLAN/WiMAX; and -less than or equal to 15.0dBm for BT. Specific FCC IDs for those devices are not necessary or identified in this analysis providing they are classified as mobile transmitters. A 100% duty cycle is used for calculations to present a worse-case analysis when applicable. Table 3: MC7350 Standalone and Collocated Transmission Declarations Mode Equipment Category Max Transmitter Duty Cycle Transmitter Range (MHz) Maximum Conducted Power Maximum Antenna Gain (dBi) (dBm) (W) Standalone Collocated CDMA EvDo 100% 824-849 25.0 0.32 6.5 3.0 1850-1910 25.0 0.32 3.0 3.0 817-824 25.0 0.32 6.5 3.0 LTE Band 13 100% 777 -787 24.0 0.25 9.0 6.0 Band 4 1710 -1755 24.0 0.25 6.0 6.0 Band 25 1850 -1915 24.0 0.25 3.0 3.0 4. MPE Calculations The WWAN MPE calculations are based on conservative conducted transmit power exceeding those listed in the FCC ID N7NMC7350 and IC number 2417C-MC7350 filing. The higher transmit power levels are used to present a worst case assessment. The WiMAX, WLAN, and BT transmit power and antenna gain parameters represent a maximum transmit power for a given frequency band. Integration of either a WiMAX or WLAN, and BT module that exceeds the parameters requires a new FCC authorization or permissive change application. A maximum antenna gain of 5 dBi for WLAN/WiMAX/BT has been assumed for all collocated antennas. Table 4, 5, and 6 summarize transmitter parameters associated with this analysis. 4.1.Individual Transmitter Calculations 4.1.1. Maximum Output Power The maximum power calculations for MC7350 per wireless technology are shown in Table 4 Technology Frequency (MHz) Maximum Conducted Power (dBm) Maximum Conducted Power (W) Maximum Antenna Gain (dBi) Duty Cycle Max EIRP (dBm) Max EIRP (W) Max ERP (dBm) Max ERP (W) Max output power limit MC7350 module(Standalone) CDMA BC0 824-849 25.0 0.32 6.5 1.000 31.500 1.413 29.360 0.863 7 W ERP CDMA BC1 1850-1910 25.0 0.32 3.0 1.000 28.000 0.631 25.860 0.385 2 W EIRP CDMA BC10 817-824 25.0 0.32 6.5 1.000 31.500 1.413 29.360 0.863 7 W ERP LTE 777 -787 24.0 0.25 9.0 1.000 33.000 1.995 30.860 1.219 3 W ERP LTE 1710 -1755 24.0 0.25 6.0 1.000 30.000 1.000 27.860 0.611 1 W EIRP LTE 1850 -1915 24.0 0.25 3.0 1.000 27.000 0.501 24.960 0.306 2 W EIRP Table 4: MC7350 Maximum Output Power Calculation 4.1.2. Standalone Power Density The power density calculations for the individual transmitters per wireless technology at an exposure minimum separation distance of 20cm are shown in Table 5. For frequency dependent limit, the lowest transmitter frequency was used to represent the lowest MPE limit in this analysis (eg. 824MHz = 0.549mW/cm 2 ) Technology Frequency (MHz) Maximum Conducted Power (dBm) Maximum Conducted Power (W) Maximum Antenna Gain (dBi) Duty Cycle Average EIRP (dBm) Average EIRP (mW) Power Density @ 20cm (mW/cm^2) FCC MPE Limit (mW/cm^2) MC7350 module(Standalone) CDMA BC0 824-849 25.0 0.32 6.5 1.000 31.50 1412.538 0.281 0.549 CDMA BC1 1850-1910 25.0 0.32 3.0 1.000 28.00 630.957 0.126 1.000 CDMA BC10 817-824 25.0 0.32 6.5 1.000 31.50 1412.538 0.281 0.544 LTE 777 -787 24.0 0.25 9.0 1.000 33.00 1995.262 0.397 0.518 LTE 1710 -1755 24.0 0.25 6.0 1.000 30.00 1000.000 0.199 1.000 LTE 1850 -1915 24.0 0.25 3.0 1.000 27.00 501.187 0.100 1.000 Table 5: MC7350 Standalone MPE Calculation 4.2. Collocated MPE Calculation The WiMAX, WLAN, and BT power levels listed represent the worse-case scenario for corresponding frequency ranges given. Technology Frequency (MHz) Maximum Conducted Power (dBm) Maximum Conducted Power (W) Maximum Antenna Gain (dBi) Duty Cycle Average EIRP (dBm) Average EIRP (mW) Power Density @ 20cm (mW/cm^2…

Text truncated - open the document above for the full version.

Report No.: FG3O0701P22 Page : 1 of 28 Report Version: Rev. 01 FCC / IC Test Report FCC ID : N7NMC7350 IC : 2417C-MC7350 Equipment : Wireless Module Model No. : AirPrime MC7350 Brand Name : AirPrime Applicant : Sierra Wireless Inc. Address : 13811 Wireless Way Richmond, British Columbia, Canada, V6V 3A4. Standard : 47 CFR FCC Part 22 Subpart H RSS-132 Issue 3 January 2013 Received Date : Oct. 07, 2013 Tested Date : Oct. 14 ~ Oct. 31, 2013 We, International Certification Corp., would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It may be duplicated completely for legal use with the approval of the applicant. It shall not be reproduced except in full without the written approval of our laboratory. Approved & Reviewed by: Gary Chang / Manager Ty: XXX Report No.: FG3O0701P22 Page : 2 of 28 Report Version: Rev. 01 Table of Contents 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information .............................................................................................................................................. 5 1.2 Local Support Equipment List ................................................................................................................ 6 1.3 Test Setup Chart .................................................................................................................................... 6 1.4 The Equipment List ................................................................................................................................ 7 1.5 Test Standards ....................................................................................................................................... 8 1.6 Measurement Uncertainty ...................................................................................................................... 8 2 TEST CONFIGURATION ....................................................................................................................... 9 2.1 Testing Condition and Location Information ........................................................................................... 9 2.2 The Worst Test Modes and Channel Details ......................................................................................... 9 3 TEST RESULTS................................................................................................................................... 10 3.1 Effective Radiated Power ..................................................................................................................... 10 3.2 Radiated Emissions .............................................................................................................................. 13 3.3 Conducted Emissions ........................................................................................................................... 17 3.4 Band Edge ............................................................................................................................................ 20 3.5 Occupied Bandwidth ............................................................................................................................ 22 3.6 Peak to Average Ratio ......................................................................................................................... 24 3.7 Frequency Stability ............................................................................................................................... 26 4 TEST LABORATORY INFORMATION ............................................................................................... 28 Report No.: FG3O0701P22 Page : 3 of 28 Report Version: Rev. 01 Release Record Report No. Version Description Issued Date FG3O0701P22 Rev. 01 Initial issue Nov. 15, 2013 Report No.: FG3O0701P22 Page : 4 of 28 Report Version: Rev. 01 Summary of Test Results FCC Rules IC Rules Test Items Measured Result 2.1046 22.913(a)(2) RSS-132 5.4 Effective Radiated Power Power[dBm] : CDMA: 23.75 Pass 2.1053 22.917(a) RSS-132 5.5 Radiated Emissions Meet the requirement of limit Pass 2.1051 22.917(a) RSS-132 5.5 Conducted Emissions Meet the requirement of limit Pass 2.1051 22.917(a) RSS-132 5.5 Band Edge Meet the requirement of limit Pass 2.1049 22.917(a) RSS-Gen 4.6.1 Occupied Bandwidth Meet the requirement of limit Pass - RSS-132 5.4 Peak to average ratio Meet the requirement of limit Pass 2.1055 22.355 RSS-132 5.3 Frequency Stability Meet the requirement of limit Pass Report No.: FG3O0701P22 Page : 5 of 28 Report Version: Rev. 01 1 General Description 1.1 Information 1.1.1 Specification of the Equipment under Test (EUT) Operating Band (MHz) CDMA2000 1xRTT 1xEV-DO Release 0, Revision A BC0, 824.7~848.31MHz Modulation QPSK, QQPSK,HPSK H/W Version 1.0 S/W Version SWI9x15E_04.04.00.00 1.1.2 Maximum ERP, Frequency Tolerance and Emission Designator System Modulation Maximum ERP (W) Emission Designator CDMA2000 HPSK 0.237 1M27F9W 1.1.3 Antenna Details Ant. No. Type Gain (dBi) Connector Remark 1 Dipole 1 SMA --- 1.1.4 EUT Operational Condition Supply Voltage AC mains DC Type of DC Source Internal DC supply External DC adapter From host Operational Voltage Vnom (120 V) Vmax (126.5 V) Vmin (93.5 V) Operational Climatic Tnom (20°C) Tmax (50°C) Tmin (-30°C) 1.1.5 Operating Channel List CDMA2000 Channel Frequency (MHz) Low 1013 824.7 Middle 384 836.52 High 777 848.31 Report No.: FG3O0701P22 Page : 6 of 28 Report Version: Rev. 01 1.2 Local Support Equipment List Support Equipment List No. Equipment Brand Model S/N FCC ID Signal cable / Length (m) 1 Fixture --- --- --- --- --- 2 Adapter for fixture GlobTek, Inc. GT-41062- 1805 --- --- USB, 1.8m shielded w/o core Note: Item 1, 2 was provided by applicant. 1.3 Test Setup Chart Test Setup Diagram Report No.: FG3O0701P2…

Text truncated - open the document above for the full version.

Report No.: FG3O0701P24 Page : 1 of 79 Report Version: Rev. 01 FCC / IC Test Report FCC ID : N7NMC7350 IC : 2417C-MC7350 Equipment : Wireless Module Model No. : AirPrime MC7350 Brand Name : AirPrime Applicant : Sierra Wireless Inc. Address : 13811 Wireless Way Richmond, British Columbia, Canada, V6V 3A4. Standard : 47 CFR FCC Part 24 Subpart E RSS-133 Issue 6 January 2013 Received Date : Oct. 07, 2013 Tested Date : Oct. 14 ~ Oct. 31, 2013 We, International Certification Corp., would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. The test results contained in this report refer exclusively to the product. It may be duplicated completely for legal use with the approval of the applicant. It shall not be reproduced except in full without the written approval of our laboratory. Approved & Reviewed by: Gary Chang / Manager Ty: XXX Report No.: FG3O0701P24 Page : 2 of 79 Report Version: Rev. 01 Table of Contents 1 GENERAL DESCRIPTION .................................................................................................................... 5 1.1 Information .............................................................................................................................................. 5 1.2 Local Support Equipment List ................................................................................................................ 7 1.3 Test Setup Chart .................................................................................................................................... 7 1.4 The Equipment List ................................................................................................................................ 9 1.5 Test Standards ..................................................................................................................................... 10 1.6 Measurement Uncertainty .................................................................................................................... 10 2 TEST CONFIGURATION ..................................................................................................................... 11 2.1 Testing Condition and Location Information ......................................................................................... 11 2.2 The Worst Test Modes and Channel Details ....................................................................................... 12 3 TEST RESULTS................................................................................................................................... 13 3.1 Equivalent Isotropically Radiated Power .............................................................................................. 13 3.2 Radiated Emissions .............................................................................................................................. 22 3.3 Conducted Emissions ........................................................................................................................... 35 3.4 Band Edge ............................................................................................................................................ 44 3.5 Occupied Bandwidth ............................................................................................................................ 58 3.6 Peak to Average Ratio ......................................................................................................................... 66 3.7 Frequency Stability ............................................................................................................................... 74 4 TEST LABORATORY INFORMATION ............................................................................................... 79 Report No.: FG3O0701P24 Page : 3 of 79 Report Version: Rev. 01 Release Record Report No. Version Description Issued Date FG3O0701P24 Rev. 01 Initial issue Nov. 15, 2013 Report No.: FG3O0701P24 Page : 4 of 79 Report Version: Rev. 01 Summary of Test Results FCC Rules IC Rules Test Items Measured Result 2.1046 24.232(c) RSS-133 6.4 Equivalent Isotropically Radiated Power Power[dBm] : CDMA: 26.24 LTE: 25.14 Pass 2.1053/ 24.238(a) RSS-133 6.5 Radiated Emissions Meet the requirement of limit Pass 2.1051 24.238(a) RSS-133 6.5 Conducted Emissions Meet the requirement of limit Pass 2.1051 24.238(a) RSS-133 6.5 Band Edge Meet the requirement of limit Pass 2.1049 24.238(a) RSS-133 2.3 Occupied Bandwidth Meet the requirement of limit Pass 24.232(d) RSS-133 6.4 Peak to average ratio Meet the requirement of limit Pass 2.1055 24.235 RSS-133 6.3 Frequency Stability Meet the requirement of limit Pass Report No.: FG3O0701P24 Page : 5 of 79 Report Version: Rev. 01 1 General Description 1.1 Information 1.1.1 Specification of the Equipment under Test (EUT) H/W Version 1.0 S/W Version SWI9x15E_04.04.00.00 CDMA 2000 BC1 Operating Band (MHz) CDMA2000 1xRTT 1xEV-DO Release 0, Revision A BC1, 1851.25~1908.75MHz Modulation QPSK, QQPSK,HPSK LTE Band 25 Operating Frequency (MHz) Channel Bandwidth: 1.4MHz: 1850.7 ~ 1914.3 Channel Bandwidth: 3MHz: 1851.5 ~ 1913.5 Channel Bandwidth: 5MHz: 1852.5 ~ 1912.5 Channel Bandwidth: 10MHz: 1855.0 ~ 1910.0 Channel Bandwidth: 15MHz: 1857.5 ~ 1907.5 Channel Bandwidth: 20MHz: 1860.0 ~ 1905.0 Modulation Type Uplink : QPSK, 16QAM Downlink : QPSK, 16QAM, 64QAM Duplex Mode FDD Category 3 1.1.2 Maximum ERP, Frequency Tolerance and Emission Designator Mode Modulation Maximum EIRP (W) Emission Designator CDMA 2000 BC1 HPSK 0.421 1M27F9W LTE Band 25, CB: 1.4MHz QPSK 0.297 1M09G7D LTE Band 25, CB: 1.4MHz 16QAM 0.231 1M09W7D LTE Band 25, CB: 3MHz QPSK 0.289 2M69G7D LTE Band 25, CB: 3MHz 16QAM 0.222 2M69W7D LTE Band 25, CB: 5MHz QPSK 0.294 4M50G7D LTE Band 25, CB: 5MHz 16QAM 0.250 4M50W7D LTE Band 25, CB: 10MHz QPSK 0.315 9M00G7D LTE Band 25, CB: 10MHz 16QAM 0.232 8M94W7D LTE Band 25, CB: 15MHz QPSK 0.284 13M46G7D LTE Band 25, CB: 15MHz 16QAM 0.218 13M46W7…

Text truncated - open the document above for the full version.

Report No.: FG3O0701P24 Page : 50 of 79 Report Version: Rev. 01 Mode LTE Band 25, CB: 5MHz, QPSK Channel 26065, 1RB Channel 26665, 1RB Channel 26065, 100%RB Channel 26665, 100%RB Report No.: FG3O0701P24 Page : 51 of 79 Report Version: Rev. 01 Mode LTE Band 25, CB: 5MHz, 16QAM Channel 26065, 1RB Channel 26665, 1RB Channel 26065, 100%RB Channel 26665, 100%RB Report No.: FG3O0701P24 Page : 52 of 79 Report Version: Rev. 01 Mode LTE Band 25, CB: 10MHz, QPSK Channel 26090, 1RB Channel 26640, 1RB Channel 26090, 100%RB Channel 26640, 100%RB Report No.: FG3O0701P24 Page : 53 of 79 Report Version: Rev. 01 Mode LTE Band 25, CB: 5MHz, 16QAM Channel 26090, 1RB Channel 26640, 1RB Channel 26090, 100%RB Channel 26640, 100%RB Report No.: FG3O0701P24 Page : 54 of 79 Report Version: Rev. 01 Mode LTE Band 25, CB: 15MHz, QPSK Channel 26115, 1RB Channel 26615, 1RB Channel 26115, 100%RB Channel 26615, 100%RB Report No.: FG3O0701P24 Page : 55 of 79 Report Version: Rev. 01 Mode LTE Band 25, CB: 15MHz, 16QAM Channel 26115, 1RB Channel 26615, 1RB Channel 26115, 100%RB Channel 26615, 100%RB Report No.: FG3O0701P24 Page : 56 of 79 Report Version: Rev. 01 Mode LTE Band 25, CB: 20MHz, QPSK Channel 26140, 1RB Channel 26590, 1RB Channel 26140, 100%RB Channel 26590, 100%RB Report No.: FG3O0701P24 Page : 57 of 79 Report Version: Rev. 01 Mode LTE Band 25, CB: 20MHz, 16QAM Channel 26140, 1RB Channel 26590, 1RB Channel 26140, 100%RB Channel 26590, 100%RB Report No.: FG3O0701P24 Page : 58 of 79 Report Version: Rev. 01 3.5 Occupied Bandwidth 3.5.1 Test Procedures 1 Set RBW =30kHz,VBW = 100 kHz, detector =Peak, sweep time = auto for CDMA mode 2 Set as below setting for LTE mode Bandwidth (MHz) RBW (kHz) VBW (KHz) Detector Sweep time 1.4 20 100 Peak Auto 3 50 200 Peak Auto 5 100 300 Peak Auto 10 200 1000 Peak Auto 15 200 1000 Peak Auto 20 300 1000 Peak Auto 3 Using occupied bandwidth measurement function of spectrum analyzer to measure occupied bandwidth. 3.5.2 Test Setup Report No.: FG3O0701P24 Page : 59 of 79 Report Version: Rev. 01 3.5.3 Test Result of Occupied Bandwidth MODE Channel Frequency (MHz) 26dB BW (MHz) 99% OBW (MHz) CDMA 25 1851.25 1.42174 1.27 CDMA 600 1880.00 1.42174 1.27 CDMA 1175 1908.75 1.41739 1.27 1xEV-DO 25 1851.25 1.41304 1.27 1xEV-DO 600 1880.00 1.41739 1.27 1xEV-DO 1175 1908.75 1.41739 1.27 Worst plots CDMA 1xEV-DO Report No.: FG3O0701P24 Page : 60 of 79 Report Version: Rev. 01 LTE Band 25, CB: 1.4MHz MODE Channel Frequency (MH…

Text truncated - open the document above for the full version.