N7NMC7354BCellular/PCS GSM/WCDMA/LTE Modem

4117529 1.0 June 12, 2015 AirPrime MC7354B Hardware Integration Guide 4117529 Rev 1.0 June 12, 2015 2 Hardware Integration Guide Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data. Safety and Hazards Do not operate the Sierra Wireless modem in areas where cellular modems are not advised without proper device certifications. These areas include environments where cellular radio can interfere such as explosive atmospheres, medical equipment, or any other equipment which may be susceptible to any form of radio interference. The Sierra Wireless modem can transmit signals that could interfere with this equipment. Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE POWERED OFF. When operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard systems. Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless modems may be used at this time. The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of a vehicle. Doing so will detract from the driver or operator’s control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence. Limitations of Liability This manual is provided “as is”. Sierra Wireless makes no warranties of any kind, either expressed or implied, including any implied warranties of merchantability, fitness for a particular purpose, or noninfringement. The recipient of the manual shall endorse all risks arising from its use. The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY. Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product. Customer understands that Sierra Wireless is not providing cellular or GPS (including A-GPS) services. These services are provided by a third party and should be purchased directly by the Customer. 4117529 Rev 1.0 June 12, 2015 3 Hardware Integration Guide SPECIFIC DISCLAIMERS OF LIABILITY: CUSTOMER RECOGNIZES AND ACKNOWLEDGES SIERRA WIRELESS IS NOT RESPONSIBLE FOR AND SHALL NOT BE HELD LIABLE FOR ANY DEFECT OR DEFICIENCY OF ANY KIND OF CELLULAR OR GPS (INCLUDING A-GPS) SERVICES. Patents This product may contain technology developed by or for Sierra Wireless Inc. This product includes technology licensed from QUALCOMM ® . This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents licensed from InterDigital Group and MMP Portfolio Licensing. Copyright © 2015 Sierra Wireless. All rights reserved. Trademarks Sierra Wireless ® , AirPrime ® , AirLink ® , AirVantage ® , WISMO ® , ALEOS ® and the Sierra Wireless and Open AT logos are registered trademarks of Sierra Wireless, Inc. or one of its subsidiaries. Watcher ® is a registered trademark of NETGEAR, Inc., used under license. Windows ® and Windows Vista ® are registered trademarks of Microsoft Corporation. Macintosh ® and Mac OS X ® are registered trademarks of Apple Inc., registered in the U.S. and other countries. QUALCOMM ® is a registered trademark of QUALCOMM Incorporated. Used under license. Other trademarks are the property of their respective owners. Contact Information Sales Desk: Phone: 1-604-232-1488 Hours: 8:00 AM to 5:00 PM Pacific Time Contact: http://www.sierrawireless.com/sales Post: Sierra Wireless 13811 Wireless Way Richmond, BC Canada V6V 3A4 Technical Support: [email protected] RMA Support: [email protected] Fax: 1-604-231-1109 Web: http://www.sierrawireless.com/ Consult our website for up-to-date product descriptions, documentation, application notes, firmware upgrades, troubleshooting tips, and press releases: www.sierrawireless.com 4117529 Rev 1.0 June 12, 2015 4 Hardware Integration Guide Document History Version Date Updates 1.0 June 12, 2015 Creation 4117529 Rev 1.0 June 12, 2015 5 Contents 1. INTRODUCTION .................................................................................................. 7 1.1. Hardware Development Components ............................................................................... 7 2. POWER INTERFACE ........................................................................................... 8 2.1. Power Supply ...…

Text truncated - open the document above for the full version.

Date: June 29, 2015 Federal Communications Commission Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: Ref: Data Re-use from FCC ID: N7NMC7355 (Approval date: 11/28/2012) Applicant: Sierra Wireless, Inc. This is to request for a test data re-use of the Radio Module, FCC ID: N7NMC7354B, Model name: N7NMC7354B Re-use the test data from the Radio Module, Existed FCC ID: N7NMC7355, Model name: MC7355 The deltas between MC7355 and MC7354B are listed below: 1. MC7354B is modified the GPS bias base on MC7355. 2. MC7354B add LTE B26 support base on MC7355. The only change is to replace MC7355 duplexer for support BC0+BC10+UMTS Band V with a single B26 duplexer which supports B26+BC0+BC10+UMTS Band V and the duplexer is PIN to PIN compatible. According to MC7354B verification report, the conducted power and the spurious emission at antenna terminal data showed similar with MC7355 test data. We apply to re-use the test data from FCC ID: N7NMC7355 for the others bands which is not relevant to the changed duplexer, CDMA/EVDO BC1, GSM850, 1900, UMTS Band II, Band IV, LTE Band 2, 4, 5, 13, 17, 25 The data re-use include testing of: Occupied Bandwidth, Spurious Emission at Antenna Terminal, Block Edge, Frequency Stability Versus Temperature, Frequency Stability Versus Temperature. If you have any questions regarding this application, please feel free to contact me. Best Regards Suzi Lan Approval Certification Engineer

Date: June 29 th , 2015 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: Re: Confidentiality Request for FCC ID: N7NMC7354B We hereby request that the exhibits listed below, submitted with our application for certification, be withheld from public disclosure. This request is made under the provisions of Section 0.457(d) and 0.459 of the Commission’s Rules, and Section 522(b)(4) of the Freedom of Information Act. We cite trade secrets as the reason and purpose of the request. Schematics Block Diagram Operation Description Tune Up Procedure Furthermore, pursuant to Public Notice DA 04-1705 in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, we request the following exhibits be withheld from public viewing for a short limited time of 180 days from the date of the Grant of Equipment Authorization, due to the sensitive business information: Integration Manual Product Photos Test Setup Photos Best Regards, Suzi Lan Approval Certification Engineer

Modular Approval Checklist FCC ID: Item Requirements EUT 1 The radio elements must have the radio frequency circuitry shielded Module RADIO elements are shielded. Please see submitted external photograph exhibits 2 The module must have buffered modulation/data inputs Module chipset design incorporates integrated buffer circuitry 3 The module must contain power supply regulation on the module Module chipset incorporates voltage regulation to transceiver circuitry 4 The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s) No applicable to licensed modules 5 The module must demonstrate compliance in a stand-alone configuration EUT conformance testing was performed in a standalone configuration 6 The licensed module must have a FCC ID label on the module itself. That FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text: Contains “FCC ID: N7NSL8084G Please refer to FCC ID label format. Labeling instruction has been provided in the user manual exhibit(s). 7 The module must comply with all specific rules applicable to the transmitter. The grantee must provide comprehensive instructions to explain compliance requirements The Module is compliant with all applicable FCC rules. Compliance requirements are stated in the user manual exhibit(s). 8 The module must comply with RF exposure requirements Compliance with RF exposure requirements is addressed in RF exposure report SL8084T N7NMC7354B MC7354B"

Sierra Wireless Inc., 13811 Wireless Way Richmond, BC Canada V6V 3A4 Tel. +1 604 231 1100 Fax. +1 604 231 1109 Date: June 29, 2015 Model # MC7354B FCC ID: N7NMC7354B IC: 2417C-MC7354B Device Photos: Enclosure, Top Surface Enclosure, Bottom Surface Disclosure:

Model: MC7354 FCC ID: N7NMC7354 IC: 2417C – MC7354 MC 7354 MC7354 Label Location B B B B B

Sierra Wireless Inc., 13811 Wireless Way Richmond, BC Canada V6V 3A4 Tel. +1 604 231 1100 Fax. +1 604 231 1109 Date: June 29, 2015 Model # MC7354B FCC ID: N7NMC7354B IC: 2417C-MC7354B Device Photos: Enclosure, Top Surface Enclosure, Bottom Surface Disclosure:

MPE Evaluation for MC7354B Wireless Module June 29, 2015 1. Introduction In this application we seek for modular approval to the MC7354B wireless module for use in standalone and collocated simultaneous transmission under mobile configuration. This Maximum Permissive Exposure (MPE) report demonstrates compliance analysis for MC7354B wireless module with FCC CFR 47 §2.1091 and IC RSS-102 for standalone and collocated transmission in mobile exposure conditions. The MPE analysis is limited for US / Canada bands only. The general population/uncontrolled exposure limits are applicable to situations in which the general public may be exposed or in which persons who are exposed as a consequence of their employment may not be made fully aware of the potential for exposure or cannot exercise control over their exposure. Any collocated transmitter must have a valid FCC ID documenting equivalent or degraded RF characteristics with the collocated parameters defined in this MPE report. A separation distance of 20cm or more shall be maintained between the end user and each WWAN, WiMAX or WLAN, and Bluetooth transmitting antenna. Portable user conditions or additional collocated transmitters not allowed based on this RF exposure analysis require a Class II permissive change and updated RF exposure report. 2. RF Exposure Limits and Equations FCC RULES: According to FCC OET Bulletin 65 Supplement C, the criteria listed in Table 1 shall be used to evaluate the environmental impact of human exposure to radio frequency (RF) radiation as specified in §1.1307. Table 1 : Limits for Maximum Permissible Exposure (MPE) IC RULES: IC has adopted the RF field strength limits established in Health Canada’s RF exposure guideline. The limits are shown in Table 2 below per RSS 102. Table 2: RF Field Strength Limits for Devices Used by the General Public (Uncontrolled Environment) EQUATIONS: Power density is given by : S = EIRP /(4 * Pi* D^2) where S = Power density (mW/cm^2) EIRP = Equivalent Isotropic Radiated Power (mW) D = Separation distance (cm) 3. Product Declarations The MC7354B wireless module can be installed for use in any mobile host as long as the antenna gain of the host antenna does not exceed the gain listed in table 3. This MPE analysis is applicable to any collocated transmitters with transmit power: -less than or equal to 29.0dBm for WLAN/WiMAX; and -less than or equal to 15.0dBm for BT. Specific FCC IDs for those devices are not necessary or identified in this analysis providing they are classified as mobile transmitters. A 100% duty cycle is used for calculations to present a worse-case analysis when applicable. Table 3: MC7354B Standalone and Collocated Transmission Declarations Mode Equipment Category Max Transmitter Duty Cycle Transmitter Range (MHz) Maximum Conducted Power Maximum Antenna Gain (dBi) (dBm) (W) Standalone Collocated GPRS Class 10 25% 824-849 33.0 2.00 4.0 4.0 1850-1910 30.0 1.00 3.0 3.0 EDGE Class 10 25% 824-849 28.0 0.63 4.0 4.0 1850-1910 27.0 0.50 3.0 3.0 Class 10 37.5% 824-849 26.2 0.42 4.0 4.0 1850-1910 25.2 0.33 3.0 3.0 Class 12 50% 824-849 28.0 0.63 4.0 4.0 1850-1910 27.0 0.50 3.0 3.0 CDMA EVDO 100% 824-849 24.5 0.28 4.0 4.0 1850-1910 24.5 0.28 3.0 3.0 816.0-823.975 24.5 0.28 4.0 4.0 UMTS HSDPA HSUPA 100% 824-849 24.0 0.25 4.0 4.0 1710-1755 24.0 0.25 4.0 4.0 1850-1910 24.0 0.25 3.0 3.0 LTE Band 17 Band 13 Band 26 Band 5 Band 4 Band 2 Band 25 100% 704-716 24.0 0.25 4.0 4.0 777-787 24.0 0.25 4.0 4.0 814-849 24.0 0.25 4.0 4.0 824-849 24.0 0.25 4.0 4.0 1710-1755 24.0 0.25 4.0 4.0 1850-1910 24.0 0.25 3.0 3.0 1850-1915 24.0 0.25 3.0 3.0 4. MPE Calculations The WWAN MPE calculations are based on conservative conducted transmit power exceeding those listed in the FCC ID N7NMC7354B and IC number 2417C-MC7354B filing. The higher transmit power levels are used to present a worst case assessment. The WiMAX, WLAN, and BT transmit power and antenna gain parameters represent a maximum transmit power for a given frequency band. Integration of either a WiMAX or WLAN, and BT module that exceeds the parameters requires a new FCC authorization or permissive change application. A maximum antenna gain of 5 dBi for WLAN/WiMAX/BT has been assumed for all collocated antennas. Table 4, 5, and 6 summarize transmitter parameters associated with this analysis. 4.1. Individual Transmitter Calculations 4.1.1. Maximum Output Power The maximum power calculations for MC7354B per wireless technology are shown in Table 4 Technology Frequency (MHz) Maximum Conducted Power (dBm) Maximum Conducted Power (W) Maximum Antenna Gain (dBi) Duty Cycle Max EIRP (dBm) Max EIRP (W) Max ERP (W) Max output power limit MC7354B module(Standalone) GPRS 2UL 824-849 33.0 2.00 4.0 0.25 37.00 5.012 3.486 7 W ERP EDGE 2UL 824-849 28.0 0.63 4.0 0.25 32.00 1.585 2.986 7 W ERP EDGE 3UL 824-849 26.2 0.42 4.0 0.375 30.20 1.047 2.806 7 W ERP EDGE 4UL 824-849 25.0 0.32 4.0 0.5 29.00 0.794 2.686 7 W ERP GPRS 2UL 1850-1910 30.0 1.00 3.0 0.25 33.00 1.995 3.086 2 W EIRP EDGE 2UL 1850-1910 27.0 0.50 3.0 0.25 30.00 1.000 2.786 2 W EIRP EDGE 3UL 1850-1910 25.2 0.33 3.0 0.375 28.20 0.661 2.606 2 W EIRP EDGE 4UL 1850-1910 24.0 0.25 3.0 0.5 27.00 0.501 2.486 2 W EIRP CDMA BC0 824-849 24.5 0.28 4.0 1 28.50 0.708 2.636 7 W ERP CDMA BC1 1850-1910 24.5 0.28 3.0 1 27.50 0.562 2.536 2 W EIRP CDMA BC10 816.0-823.975 24.5 0.28 4.0 1 28.50 0.708 2.636 7 W ERP UMTS 824-849 24.0 0.25 4.0 1 28.00 0.631 2.586 7 W ERP UMTS 1710-1755 24.0 0.25 4.0 1 28.00 0.631 2.586 1 W EIRP UMTS 1850-1910 24.0 0.25 3.0 1 27.00 0.501 2.486 2 W EIRP LTE 704-716 24.0 0.25 4.0 1 28.00 0.631 2.586 3 W ERP LTE 777-787 24.0 0.25 4.0 1 28.00 0.631 2.586 3 W ERP LTE 814-849 24.0 0.25 4.0 1 28.00 0.631 2.586 7 W ERP LTE 824-849 24.0 0.25 4.0 1 28.00 0.631 2.586 7 W ERP LTE 1710-1755 24.0 0.25 4.0 1 28.00 0.631 2.586 1W EIRP LTE 1850-1910 24.0 0.25 3.0 1 27.00 0.501 2.486 2 W EIRP LTE 1850-1915 24.0 0.25 3.0 1 27.00 0.501 2.486 2 W EIRP Table 4: MC7354B Maximum Output Power Calculation 4.1.…

Text truncated - open the document above for the full version.

 2010 Sierra Wireless, Inc. This document contains information which is proprietary and confidential to Sierra Wireless, Inc. Disclosure to persons other than the officers, employees, agents, or subcontractors of the Company or licensee of this document without the prior written permission of Sierra Wireless, Inc. is strictly prohibited. MC7355 Modem FOR GSM / EDGE FCC and IC Certifications IC: 2417C-MC7355 FCC ID: N7NMC7355 SIERRA WIRELESS, INC. FCC Part 22/24, RSS-132/133 MC7355 Aug. 16, 2012 Page 2 of 20  2010 Sierra Wireless, Inc. The contents of this page are subject to the confidentiality information on page one. Table of Contents 1 Introduction and Purpose ......................................................................... 3 2 Test Summary .......................................................................................... 3 3 Description of Equipment under Test ...................................................... 3 4 Compliance Test Equipment List ............................................................ 4 5 Test Setup Block Diagrams ..................................................................... 4 5.1 Test Setup 1 ......................................................................................................... 4 5.2 Test Setup 2 ......................................................................................................... 5 6 RF Power Output ..................................................................................... 5 6.1 Test Procedure .................................................................................................... 5 6.1.1 GSM/GPRS/EDGE Max Power Setup ........................................................... 5 6.2 Maximum Transmit Power Test Results ............................................................. 5 6.2.1 Test Results GSM/EDGE Output Power ........................................................ 5 7 Occupied Bandwidth ................................................................................ 6 7.1 Test Procedure .................................................................................................... 6 7.2 Test Results ......................................................................................................... 6 7.2.1 GSM Summary Results ................................................................................... 6 7.2.2 GSM Test Plots ............................................................................................... 7 8 Out of Band Emissions at Antenna Terminals ........................................ 8 8.1 Test Procedure .................................................................................................... 9 8.2 Test Results ......................................................................................................... 9 8.2.1 GSM Test Plots ............................................................................................... 9 9 Block Edge Compliance ........................................................................ 14 9.1 Test Procedure .................................................................................................. 14 9.2 Test Results ....................................................................................................... 14 9.2.1 GSM Test Plots ............................................................................................. 15 10 Frequency Stability versus Temperature ............................................ 18 10.1 Summary of Results ........................................................................................... 18 10.2 Test Procedure .................................................................................................. 19 10.3 Test Results ....................................................................................................... 19 10.3.1 GSM Frequency Error over Temperature ................................................ 19 11 Frequency Stability versus Voltage .................................................... 19 11.1 Summary of Results ........................................................................................... 19 11.2 Test Procedure .................................................................................................. 19 11.3 Test Results ....................................................................................................... 20 11.3.1 GSM Frequency Error over Voltage ......................................................... 20 SIERRA WIRELESS, INC. FCC Part 22/24, RSS-132/133 MC7355 Aug. 16, 2012 Page 3 of 20  2010 Sierra Wireless, Inc. The contents of this page are subject to the confidentiality information on page one. 1 Introduction and Purpose This document provides test data for the MC7355 modem output power intended for FCC and Industry Canada certifications. 2 Test Summary FCC Rule IC Standards DESCRIPTION OF TEST RESULT PAGE 2.1046 RSS-132, 4.4 RSS-133, 6.4 RF Power Output Complies 6 2.1049 RSS-Gen, 4.6 Occupied Bandwidth Complies 7 2.1051, 22.917, 24.238 RSS-132, 4.5 RSS-133, 6.5 Out of Band Emissions at Antenna Terminals Complies 9 22.917, 24.238 RSS-Gen, 4.6 Block Edge Compliance Complies 15 2.1055, 22.355, 24.235 RSS-132, 4.3 RSS-133, 6.3 Frequency Stability versus Temperature Complies 19 2.1055, 22.355, 24.235 RSS-132, 4.3 RSS-133, 6.3 Frequency Stability versus Voltage Complies 20 3 Description of Equipment under Test The MC7355 modem, referred to as “EUT” hereafter, is a multi-band wireless modem operating on the GSM/GPRS/EDGE/UMTS/LTE/CDMA networks. The table below shows the supported North American bands for the device. Technology Band UL Freq. (MHz) DL Freq. (MHz) Max Power LTE B2 1850 – 1910 1930 – 1990 23 dBm (+/- 1 dB) B4 1710 – 1755 2110 – 2155 23 dBm (+/- 1 dB) B5 824 – 849 869 – 894 23 dBm (+/- 1 dB) B13 777 – 787 746 – 756 23 dBm (+/- 1 dB) B17 704 – 716 734 – 746 23 dBm (+/- 1 dB) B25 1850 – 1915 1930 – 1995 23 dBm (+/- 1 dB) WCDMA…

Text truncated - open the document above for the full version.

 2010 Sierra Wireless, Inc. This document contains information which is proprietary and confidential to Sierra Wireless, Inc. Disclosure to persons other than the officers, employees, agents, or subcontractors of the Company or licensee of this document without the prior written permission of Sierra Wireless, Inc. is strictly prohibited. MC7355 Modem Test Report FOR WCDMA / HSPA FCC and IC Certifications IC: 2417C-MC7355 FCC ID: N7NMC7355 SIERRA WIRELESS, INC. FCC Part 22/24/27, RSS-132/133/139 MC7355 Aug. 16, 2012 Page 2 of 23  2010 Sierra Wireless, Inc. The contents of this page are subject to the confidentiality information on page one. Table of Contents 1 Introduction and Purpose ......................................................................... 3 2 Test Summary .......................................................................................... 3 3 Description of Equipment under Test ...................................................... 3 4 Compliance Test Equipment List ............................................................ 4 5 Test Setup Block Diagrams ..................................................................... 4 5.1 Test Setup 1 ......................................................................................................... 4 5.2 Test Setup 2 ......................................................................................................... 5 6 RF Power Output ..................................................................................... 5 6.1 Test Procedure .................................................................................................... 5 6.1.1 WCDMA/HSDPA/HSUPA Max Power setup ............................................... 5 6.2 Maximum Transmit Power Test Results ............................................................. 8 6.2.1 Test Results for WCDMA/HSDPA/HSUPA Output Power ........................... 8 7 Occupied Bandwidth ................................................................................ 8 7.1 Test Procedure .................................................................................................... 8 7.2 Test Results ......................................................................................................... 8 7.2.1 WCDMA Summary Results ........................................................................... 8 7.2.2 WCDMA Rel99 Test Plots ............................................................................. 9 7.2.3 HSUPA Rel6 (Subtest 5) Test Plots.............................................................. 10 8 Out of Band Emissions at Antenna Terminals ...................................... 11 8.1 Test Procedure .................................................................................................. 12 8.2 Test Results ....................................................................................................... 12 8.2.1 WCDMA Rel99 Test Plots ........................................................................... 12 9 Block Edge Compliance ........................................................................ 16 9.1 Test Procedure .................................................................................................. 16 9.2 Test Results ....................................................................................................... 16 9.2.1 WCDMA Test Plots ...................................................................................... 17 10 Frequency Stability versus Temperature ............................................ 19 10.1 Summary of Results ........................................................................................... 19 10.2 Test Procedure .................................................................................................. 20 10.3 Test Results ....................................................................................................... 20 10.3.1 UMTS Frequency Error over Temperature .............................................. 20 11 Frequency Stability versus Voltage .................................................... 20 11.1 Summary of Results ........................................................................................... 20 11.2 Test Procedure .................................................................................................. 20 11.3 Test Results ....................................................................................................... 21 11.3.1 UMTS Frequency Error over Voltage ...................................................... 21 12 Peak to Average Ratio ........................................................................ 21 12.1 Summary of Results ........................................................................................... 21 12.2 Test Procedure .................................................................................................. 21 12.3 Test Results ....................................................................................................... 21 12.3.1 Test Plots ................................................................................................... 22 SIERRA WIRELESS, INC. FCC Part 22/24/27, RSS-132/133/139 MC7355 Aug. 16, 2012 Page 3 of 23  2010 Sierra Wireless, Inc. The contents of this page are subject to the confidentiality information on page one. 1 Introduction and Purpose This document provides test data for the MC7355 modem output power intended for FCC and Industry Canada certifications. 2 Test Summary FCC Rule IC Standards DESCRIPTION OF TEST RESULT PAGE 2.1046 RSS-132, 4.4 RSS-133, 6.4 RF Power Output Complies 5 2.1049 RSS-Gen, 4.6 Occupied Bandwidth Complies 2.1051, 22.917, 24.238, 27.53 RSS-132, 4.5 RSS-133, 6.5 Out of Band Emissions at Antenna Terminals Complies 22.917, 24.238, 27.53 RSS-Gen, 4.6 Block Edge Compliance Complies 2.1055, 22.355, 24.235, 27.54 RSS-132, 4.3 RSS-133, 6.3 Frequency Stability versus Temperature Complies…

Text truncated - open the document above for the full version.

 2010 Sierra Wireless, Inc. This document contains information which is proprietary and confidential to Sierra Wireless, Inc. Disclosure to persons other than the officers, employees, agents, or subcontractors of the Company or licensee of this document without the prior written permission of Sierra Wireless, Inc. is strictly prohibited. MC7355 Modem Test Report FOR LTE FCC and IC Certifications IC: 2417C-MC7355 FCC ID: N7NMC7355 SIERRA WIRELESS, INC. FCC Part 22/24/27, RSS-132/133/139 MC7355 Aug. 16, 2012 Page 2 of 109  2010 Sierra Wireless, Inc. The contents of this page are subject to the confidentiality information on page one. Table of Contents 1 Introduction and Purpose .............................................................................................. 4 2 Test Summary................................................................................................................ 4 3 Description of Equipment under Test ........................................................................... 4 4 Compliance Test Equipment List ............................…

Text truncated - open the document above for the full version.