N7NMC74BRadio Module

AirPrime MC7411 Hardware Integration Guide 41114156 Rev. 2 Hardware Integration Guide Rev. 2 January 2021241114156 Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless product are used in a normal manner with a well-constructed network, the Sierra Wireless product should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless product, or for failure of the Sierra Wireless product to transmit or receive such data. Safety and Hazards Do not operate the Sierra Wireless product in areas where blasting is in progress, where explosive atmospheres may be present, near medical equipment, near life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the Sierra Wireless product MUST BE POWERED OFF. The Sierra Wireless product can transmit signals that could interfere with this equipment. Do not operate the Sierra Wireless product in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless product MUST BE POWERED OFF. When operating, the Sierra Wireless product can transmit signals that could interfere with various onboard systems. Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless products may be used at this time. The driver or operator of any vehicle should not operate the Sierra Wireless product while in control of a vehicle. Doing so will detract from the driver or operator’s control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence. Limitation of Liability The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY. Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product. PatentsThis product may contain technology developed by or for Sierra Wireless Inc. This product includes technology licensed from QUALCOMM ® . This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents licensed from MMP Portfolio Licensing. Preface Rev. 2 January 2021341114156 Copyright© 2021 Sierra Wireless. All rights reserved. TrademarksSierra Wireless ® , AirPrime ® , AirLink ® , AirVantage ® and the Sierra Wireless logo are registered trademarks of Sierra Wireless. Windows ® and Windows Vista ® are registered trademarks of Microsoft Corporation. Macintosh ® and Mac OS X ® are registered trademarks of Apple Inc., registered in the U.S. and other countries. QUALCOMM ® is a registered trademark of QUALCOMM Incorporated. Used under license. Other trademarks are the property of their respective owners. Contact Information Revision History Sales information and technical support, including warranty and returns Web: sierrawireless.com/company/contact-us/ Global toll-free number: 1-877-687-7795 6:00 am to 5:00 pm PST Corporate and product informationWeb: sierrawireless.com Revision number Release dateChanges 1December 2020Created 2January 2021General update Rev. 2 January 2021441114156 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Required Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Power Supply. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Module Power States. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 RF Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Supported RF Bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 RF Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Shielding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Antenna and Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Ground Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Interference and Sensitivity . . . . . .…

Text truncated - open the document above for the full version.

Limited Modular Approval Checklist FCC ID: N7NMC74B Item Requirements EUT 1 The radio elements must have the radio frequency circuitry shielded Module RADIO elements are shielded. Please see submitted external photograph exhibits 2 The module must have buffered modulation/data inputs Module chipset design incorporates integrated buffer circuitry 3 The module must contain power supply regulation on the module Module chipset incorporates voltage regulation to transceiver circuitry 4 The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s) No applicable to licensed modules 5 The module must demonstrate compliance in a stand-alone configuration EUT conformance testing was performed in a standalone configuration 6 The licensed module must have a FCC ID label on the module itself. That FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text: Contains “FCC ID: N7NMC74B” Please refer to FCC ID label format. Labeling instruction has been provided in the user manual exhibit(s). 7 The module must comply with all specific rules applicable to the transmitter. The grantee must provide comprehensive instructions to explain compliance requirements The Module is compliant with all applicable FCC rules. Compliance requirements are stated in the user manual exhibit(s). 8 The module must comply with RF exposure requirements Compliance with RF exposure requirements is addressed in RF exposure report Sincerely, __________________________ By: Denis CHABOT Title: Senior Manager, Certification Company: Sierra Wireless Inc. Telephone: +852 2824 5222 e-mail: [email protected]

Request for Confidentiality Date: January 4, 2021 Subject: Confidentiality Request for: N7NMC74B and 2417C-MC74B Pursuant to FCC 47 CFR 0.457(d) and 0.459 and IC RSP-100, Section 9.4, the applicant requests that a part of the subject FCC application be held confidential. Type of Confidentiality Requested Exhibit ☐ Short Term ☒ Permanent Block Diagrams ☒ Short Term External Photos ☒ Short Term ☐ Permanent * 1 Internal Photos ☐ Short Term ☒ Permanent Operation Description/Theory of Operation ☐ Short Term ☒ Permanent Parts List & Placement/BOM ☐ Short Term ☒ Permanent Tune-Up Procedure ☐ Short Term ☒ Permanent Schematics ☒ Short Term Test Setup Photos ☒ Short Term ☐ Permanent * 3 User’s Manual Sierra Wireless Inc. has spent substantial effort in developing this product and it is one of the first of its kind in industry. Having the subject information easily available to "competition" would negate the advantage they have achieved by developing this product. Not protecting the details of the design will result in financial hardship. Permanent Confidentiality: The applicant requests the exhibits listed above as permanently confidential be permanently withheld from public review due to materials that contain trade secrets and proprietary information not customarily released to the public. Short-Term Confidentiality: The applicant requests the exhibits selected above as short term confidential be withheld from public view for a period of 180 days from the date of the Grant of Equipment Authorization and prior to marketing. This is to avoid premature release of sensitive information prior to marketing or release of the product to the public. Applicant is also aware that they are responsible to notify ACB in the event information regarding the product or the product is made available to the public before the requested period has expired. ACB will then release the documents listed above for public disclosure pursuant to FCC Public Notice DA 04-1705. NOTE for Industry Canada Applications: IC currently only distinguishes Permanent Confidentiality exhibits as shown above. Short Term confidentiality is not considered applicable to IC applications. Sincerely, By: Denis CHABOT Senior Manager, Certification 1 - The asterisked items (*) require further information to be provided to ACB before permanent confidentiality will be extended to these exhibits. Please refer to FCC KDB 726920 and the specific Document link for D01 found at: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=41731 and review section II, 3) regarding specific information that must accompany these requests.

MC7411 – External photos Top Bottom

MC7411 – Internal photos

MPE Evaluation for MC7411 Radio Module January 4, 2021 Contents 1. Introduction..................................................................................................... 2 2. RF Exposure Limits and Equations ................................................................ 3 3. Stand-Alone Transmission ............................................................................. 5 4. Collocated Transmission ................................................................................ 6 5. Conclusion...................................................................................................... 7 1. Introduction In this application we seek modular approval for the MC7411 radio module for use in standalone and collocated simultaneous transmission under mobile and fixed configurations. This Maximum Permissive Exposure (MPE) report demonstrates compliance analysis for MC7411 radio module with FCC CFR 47 §2.1091 and IC RSS-102 for standalone and collocated transmission in the exposure conditions where a separation distance of at least 20 centimeters is normally maintained between the transmitter's radiating structure(s) and the body of the user or nearby persons. The MPE analysis is limited for US / Canada bands only. The general population/uncontrolled exposure limits are applicable to situations in which the general public may be exposed or in which persons who are exposed as a consequence of their employment may not be made fully aware of the potential for exposure or cannot exercise control over their exposure. 2. RF Exposure Limits and Equations FCC Limits: According to FCC OET Bulletin 65 Supplement C, the criteria listed in Table 1 shall be used to evaluate the environmental impact of human exposure to radio frequency (RF) radiation as specified in §1.1307. Table 1 : Limits for Maximum Permissible Exposure (MPE) IC Limits: IC has adopted the RF field strength limits established in Health Canada’s RF exposure guideline. The limits are shown in Table 2 below per RSS- 102. Table 2 : RF Field Strength Limits for Devices Used by the General Public (Uncontrolled Environment) In the frequency range of 300-6000 MHz, the IC limits are more stringent than the FCC limits. The MPE evaluation in this report will be based on the IC limits, so the deduced output power and antenna gain limits will guarantee compliance with both FCC and IC requirements. EQUATIONS: EIRP (dBm) = Conducted Power (dBm) + Antenna Gain (dBi) Power density is given by : S = EIRP / (4 π * D^2) where S = Power density (mW/cm^2) EIRP = Equivalent Isotropic Radiated Power (mW) D = Separation distance (cm) 3. Stand-Alone Transmission When MC7411 module transmits as a stand-alone mobile device, the source- based time-averaged EIRP is calculated by summing up conducted power and antenna gain. A 100% duty cycle is used for calculations to present a worse-case analysis. The antenna gains are chosen so that the resulted radiated power levels are within the limits specified by the FCC rules and IC Radio Standards Specifications (RSS). The IC exemption limits for routine RF exposure evaluation are calculated using the lowest frequency of the operating band presenting the most stringent limits. As shown in Table 2 below, the resulted EIRP are always below the IC exemption limits for all the operating modes. Operating Mode TX Freq Range (MHz) Max Time- Avg Cond Power (dBm) Max Time- Avg Cond Power (W) Max Ant Gain (dBi) Source- Based Time- Averaged Max EIRP (dBm) IC Exemption Limit (EIRP) (dBm) EIRP/ERP Limits WCDMA/LTE Band 2 1850 1910 24 0.25 6 30 33.50 2 W EIRP WCDMA/LTE Band 4 1710 1755 24 0.25 6 30 33.27 2 W EIRP WCDMA/LTE Band 5 824 849 24.3 0.27 6 30.3 31.10 2 W EIRP LTE Band 7 2500 2570 23.8 0.24 9 32.8 34.39 2 W EIRP LTE Band 12 699 716 24 0.25 6 30 30.61 2 W EIRP LTE Band 13 777 787 24 0.25 6 30 30.93 2 W EIRP LTE Band 14 788 798 24 0.25 6 30 30.97 2 W EIRP LTE Band 25 1850 1915 24 0.25 6 30 33.50 2 W EIRP LTE Band 26 814 849 24 0.25 6 30 31.06 2 W EIRP LTE Band 41 2496 2690 23.8 0.24 9 32.8 34.39 2 W EIRP LTE Band 42 3400 3600 23.8 0.24 9 32.8 35.31 2 W EIRP LTE Band 43 3600 3800 23.8 0.24 9 32.8 35.48 2 W EIRP LTE Band 48 3550 3700 23.8 0.24 9 32.8 35.43 2 W EIRP LTE Band 66 1710 1780 24 0.25 6 30 33.27 2 W EIRP LTE Band 71 663 698 24 0.25 6 30 30.45 2 W EIRP Table 2: MC7411 Stand-Alone Transmission 4. Collocated Transmission When MC7411 module co-transmits with radio transmitter(s) as a mobile device, per KDB 447498 D01, simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on the calculated/estimated, numerically modeled or measured field strengths or power density, is ≤ 1.0. The evaluation here considers a WiMAX or WLAN transmitter, and a Bluetooth transmitter as collocated transmitters. Their radiated output power levels are listed in Table 3 below. The MPE ratio is defined by the ratio of power density to MPE limit. The sum of the MPE ratios is calculated as follows: ∑푀푃퐸 푅푎푡푖표 = Max (MC7411 MPE ratio) + Max (WLAN MPE ratio) + BT MPE Ratio + Max (WiGig MPE ratio) = 0.548+0.372+0.011+0.063=0.994 < 1.0 Operating Mode TX Freq Range (MHz) Max Time- Avg Cond Power (dBm) Max Time- Avg Cond Power (W) Max Ant Gain (dBi) Source- Based Time- Averaged Max EIRP Power Density @20 cm (W/m^2) IC MPE Limit (W/m2) IC PwrDensity MPE Ratio WCDMA/LTE Band 2 1850 1910 24 0.25 6 30 1.99 4.48 0.444 WCDMA/LTE Band 4 1710 1755 24 0.25 6 30 1.99 4.24 0.469 WCDMA/LTE Band 5 824 849 24.3 0.27 4 28.3 1.35 2.58 0.522 LTE Band 7 2500 2570 23.8 0.24 4 27.8 1.20 5.50 0.218 LTE Band 12 699 716 24 0.25 4 28 1.26 2.30 0.545 LTE Band 13 777 787 24 0.25 4 28 1.26 2.47 0.507 LTE Band 14 788 798 24 0.25 4 28 1.26 2.50 0.502 LTE Band 25 1850 1915 24 0.25 6 30 1.99 4.48 0.444 LTE Band 26 814 849 24 0.25 4 28 1.26 2.55 0.491 LTE Band 41 2496 2690 23.8 0.24 8 31.8 3.01 5.49 0.548 LTE Band 42 3400 3600 23.8 0.24 8 31.8 3.01 6.78 0.444 LTE B…

Text truncated - open the document above for the full version.

Report No.: 20C0725R-E3042110011 Page: 1 of 75 FCC/ISED Test Report Product Name : Module Trade Name : AirPrime Model No. : MC7411 FCC ID : N7NMC74B IC : 2417C-MC74B Applicant : SIERRA WIRELESS, INC. Address : 13811 Wireless Way, Richmond, BC, Canada V6V 3A4 Canada Date of Receipt : Dec. 18, 2020 Issued Date : Jan. 14, 2021 Report No. : 20C0725R-E3042110011 Report Version : V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of DEKRA Testing and Certification Co., Ltd. Report No.: 20C0725R-E3042110011 Page: 2 of 75 Test Report Certification Issued Date: Jan. 14, 2021 Report No.: 20C0725R-E3042110011 Product Name : Module Applicant : SIERRA WIRELESS, INC. Address : 13811 Wireless Way, Richmond, BC, Canada V6V 3A4 Canada Manufacturer : SIERRA WIRELESS, INC. Trade Name : AirPrime Model No. : MC7411 FCC ID : N7NMC74B IC : 2417C-MC74B EUT Voltage : DC 3.7V Testing Voltage : DC 3.7V Applicable Standard : FCC CFR Title 47 Part 22 Subpart H FCC CFR Title 47 Part 24 Subpart E FCC CFR Title 47 Part 27 Subpart M ISED RSS-GEN Issue 5, ISED RSS-132 Issue 3 ISED RSS-133 Issue 6, ISED RSS-139 Issue 3, ANSI/TIA-603-E-2016 Test Lab : Hsin Chu Laboratory Address : No.372-2, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 310, Taiwan, R.O.C. TEL: +886-3-582-8001 / FAX: +886-3-582-8958 Test Result : Complied Documented By : ( Demi Chang / Senior Engineering Adm. Specialist ) Tested By : ( Max Chang / Senior Engineer ) Approved By : ( Louis Hsu / Deputy Manager ) Report No.: 20C0725R-E3042110011 Page: 3 of 75 Revision History Version Description Issued Date V1.0 Initial issue of report Jan. 14, 2021 Report No.: 20C0725R-E3042110011 Page: 4 of 75 TABLE OF CONTENTS Description Page 1. General Information .......................................................................................................... 6 1.1. EUT Description ................................................................................................................ 6 1.2. Mode of Operation ............................................................................................................ 7 1.3. Tested System Details ...................................................................................................... 8 1.4. Configuration of Tested System ........................................................................................ 8 1.5. EUT Exercise Software ..................................................................................................... 8 1.6. Comments and Remarks .................................................................................................. 9 2. Technical Test .................................................................................................................. 10 2.1. Summary of Test Result .................................................................................................. 10 2.2. Test Environment ............................................................................................................ 12 2.3. List of Test Equipment ..................................................................................................... 13 2.4. Measurement Uncertainty ............................................................................................... 16 3. RF Output Power ............................................................................................................ 17 3.1. Test Setup ....................................................................................................................... 17 3.2. Test Procedure ................................................................................................................ 17 3.3. Test Method .................................................................................................................... 17 3.4. Test Result ...................................................................................................................... 18 4. Occupied Bandwidth ....................................................................................................... 21 4.1. Test Setup ....................................................................................................................... 21 4.2. Test Procedure ................................................................................................................ 21 4.3. Test Method .................................................................................................................... 21 4.4. Test Result ...................................................................................................................... 22 5. Peak To Average Ratio .................................................................................................... 28 5.1. Test Setup ....................................................................................................................... 28 5.2. Test Procedure ................................................................................................................ 28 5.3. Test Method .................................................................................................................... 28 5.4. Test Result ...................................................................................................................... 29 6. Conducted Band Edge .................................................................................................... 35 6.1. Test Setup ....................................................................................................................... 35 6.2. Test Procedure ................................................................................................................ 35 6.3. Test Method .................................................................................................................... 35 6.4. Test Result .....................................…

Text truncated - open the document above for the full version.

Report No.: 20C0725R-E3042110012 Page: 1 of 1011 FCC/ISED Test Report Product Name : Module Trade Name : AirPrime Model No. : MC7411 FCC ID : N7NMC74B IC : 2417C-MC74B Applicant : SIERRA WIRELESS, INC. Address : 13811 Wireless Way, Richmond, BC, Canada V6V 3A4 Canada Date of Receipt : Dec. 18, 2020 Issued Date : Jan. 14, 2021 Report No. : 20C0725R-E3042110012 Report Version : V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of DEKRA Testing and Certification Co., Ltd.. Report No.: 20C0725R-E3042110012 Page: 2 of 1011 Test Report Certification Issued Date : Jan. 14, 2021 Report No. : 20C0725R-E3042110012 Product Name : Module Applicant : SIERRA WIRELESS, INC. Address : 13811 Wireless Way, Richmond, BC, Canada V6V 3A4 Canada Manufacturer : SIERRA WIRELESS, INC. Trade Name : AirPrime Model No. : MC7411 FCC ID : N7NMC74B IC : 2417C-MC74B EUT Voltage : DC 3.7V Testing Voltage : DC 3.7V Applicable Standard : FCC CFR Title 47 Part 22 Subpart H FCC CFR Title 47 Part 24 Subpart E FCC CFR Title 47 Part 27 Subpart L, Subpart M, Subpart F FCC CFR Title 47 Part 90 Subpart S, Subpart R ANSI/TIA-603 RSS-GEN Issue 5, RSS-130 Issue 2, RSS-132 Issue 3, RSS-133 Issue 6, RSS-139 Issue 3, RSS-140 Issue 1, RSS-199 Issue 3 Test Lab : Hsin Chu Laboratory Address : No.372-2, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 310, Taiwan, R.O.C. TEL: +886-3-582-8001 / FAX: +886-3-582-8958 Test Result : Complied Documented By : ( Demi Chang / Senior Engineering Adm. Specialist ) Tested By : ( Max Chang / Senior Engineer ) Approved By : ( Louis Hsu / Deputy Manager ) Report No.: 20C0725R-E3042110012 Page: 3 of 1011 Revision History Version Description Issued Date V1.0 Initial issue of report Jan. 14, 2021 Report No.: 20C0725R-E3042110012 Page: 4 of 1011 TABLE OF CONTENTS Description Page 1. General Information .................................................................................................... 6 1.1. EUT Description ......................................................................................................... 6 1.2. Mode of Operation ...................................................................................................... 7 1.3. Tested System Details ................................................................................................ 8 1.4. Configuration of Tested System .................................................................................. 8 1.5. Operation Descriptions ............................................................................................... 8 1.6. Comments and Remarks ............................................................................................ 9 2. Technical Test ........................................................................................................... 10 2.1. Summary of Test Result ............................................................................................ 10 2.2. Test Environment ...................................................................................................... 25 2.3. List of Test Equipment .............................................................................................. 26 2.4. Measurement Uncertainty ......................................................................................... 29 3. RF Output Power ...................................................................................................... 30 3.1. Test Setup................................................................................................................. 30 3.2. Test Procedure ......................................................................................................... 30 3.3. Test Method .............................................................................................................. 30 3.4. Test Result ................................................................................................................ 31 4. Occupied Bandwidth ............................................................................................... 119 4.1. Test Setup............................................................................................................... 119 4.2. Test Procedure ....................................................................................................... 119 4.3. Test Method ............................................................................................................ 119 4.4. Test Result .............................................................................................................. 120 5. Peak To Average Ratio .......................................................................................... 434 5.1. Test Setup............................................................................................................... 434 5.2. Test Procedure ....................................................................................................... 434 5.3. Test Method ............................................................................................................ 434 5.4. Test Result .............................................................................................................. 435 6. Spurious Emissions ................................................................................................ 635 6.1. Test Setup............................................................................................................... 635 6.2. Test Procedure ....................................................................................................... 636 6.3. Test Method ............................................................................................................ 636 6.4. Test Result .............................................................................................................. 637 7. Spurious Emissions at Ant…

Text truncated - open the document above for the full version.

Report No.: 20C0725R-E3042110012 Page: 114 of 1011 Product Module Test Item RF Output Power Test Mode Mode 11: LTE CA Band 5B Date of Test 2020/12/31 Test Site SR12-H Temperature(°C) 20 Humidity (%RH) 59 Note: 1. Measure Level (ERP) = Reading Level (dBm) + Antenna Gain(dBi)-2.15dB 2. power (W)= (10 (power(dBm)/10) )*10 -3 Report No.: 20C0725R-E3042110012 Page: 115 of 1011 Product Module Test Item RF Output Power Test Mode Mode 12: LTE CA Band 7C Date of Test 2020/12/31 Test Site SR12-H Temperature(°C) 20 Humidity (%RH) 59 Note: 1. Measure Level (EIRP) = Reading Level (dBm) + Antenna Gain(dBi) 2. power (W)= (10 (power(dBm)/10) )*10 -3 Report No.: 20C0725R-E3042110012 Page: 116 of 1011 Product Module Test Item RF Output Power Test Mode Mode 13: LTE CA Band 41C (FCC) Date of Test 2020/12/31 Test Site SR12-H Temperature(°C) 20 Humidity (%RH) 59 Report No.: 20C0725R-E3042110012 Page: 117 of 1011 Note: 1. Measure Level (EIRP) = Reading Level (dBm) + Antenna Gain(dBi) 2. power (W)= (10 (power(dBm)/10) )*10 -3 Report No.: 20C0725R-E3042110012 Page: 118 of 1011 Product Module Test Item RF Output Power Test Mode Mode 13: LTE CA Band 41C (ISED) Date of Test 2020/09/02 Test Site SR12-H Temperature(°C) 23 Humidity (%RH) 67 Note: 1. Measure Level (EIRP) = Reading Level (dBm) + Antenna Gain(dBi) 2. power (W)= (10 (power(dBm)/10) )*10 -3 Report No.: 20C0725R-E3042110012 Page: 119 of 1011 4. Occupied Bandwidth 4.1. Test Setup 4.2. T…

Text truncated - open the document above for the full version.