N7NRC76BRadio Module

AirPrime RC7611 Hardware Integration Guide 41113583 Rev 1.0 Hardware Integration Guide Rev 1.0 Jan 20241113583 Important Notice Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices such as the Sierra Wireless modem are used in a normal manner with a well-constructed network, the Sierra Wireless modem should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. Sierra Wireless accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using the Sierra Wireless modem, or for failure of the Sierra Wireless modem to transmit or receive such data. Safety and Hazards Do not operate the Sierra Wireless modem in areas where blasting is in progress, where explosive atmospheres may be present, near medical equipment, near life support equipment, or any equipment which may be susceptible to any form of radio interference. In such areas, the Sierra Wireless modem MUST BE IN AIRPLANE MODE OR POWERED OFF. The Sierra Wireless modem can transmit signals that could interfere with this equipment. Do not operate the Sierra Wireless modem in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, the Sierra Wireless modem MUST BE IN AIRPLANE MODE OR POWERED OFF. When operating, the Sierra Wireless modem can transmit signals that could interfere with various onboard systems. Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. Sierra Wireless modems may be used at this time. The driver or operator of any vehicle should not operate the Sierra Wireless modem while in control of a vehicle. Doing so will detract from the driver or operator's control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence. Limitation of Liability The information in this manual is subject to change without notice and does not represent a commitment on the part of Sierra Wireless. SIERRA WIRELESS AND ITS AFFILIATES SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL DIRECT, INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR EXEMPLARY DAMAGES INCLUDING, BUT NOT LIMITED TO, LOSS OF PROFITS OR REVENUE OR ANTICIPATED PROFITS OR REVENUE ARISING OUT OF THE USE OR INABILITY TO USE ANY SIERRA WIRELESS PRODUCT, EVEN IF SIERRA WIRELESS AND/OR ITS AFFILIATES HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THEY ARE FORESEEABLE OR FOR CLAIMS BY ANY THIRD PARTY. Notwithstanding the foregoing, in no event shall Sierra Wireless and/or its affiliates aggregate liability arising under or in connection with the Sierra Wireless product, regardless of the number of events, occurrences, or claims giving rise to liability, be in excess of the price paid by the purchaser for the Sierra Wireless product. Preface Rev 1.0 Jan 20341113583 PatentsThis product may contain technology developed by or for Sierra Wireless Inc. This product is manufactured or sold by Sierra Wireless Inc. or its affiliates under one or more patents licensed from MMP Portfolio Licensing. Copyright©2020 Sierra Wireless. All rights reserved. TrademarksSierra Wireless ® , AirPrime ® , AirLink ® , AirVantage ® and the Sierra Wireless logo are registered trademarks of Sierra Wireless, Inc. Windows ® and Windows Vista ® are registered trademarks of Microsoft Corporation. QUALCOMM ® is a registered trademark of QUALCOMM Incorporated. Used under license. Other trademarks are the property of their respective owners. Contact Information Revision History Sales information and technical support, including warranty and returns Web: sierrawireless.com/company/contact-us/ Global toll-free number: 1-877-687-7795 6:00 am to 5:00 pm PST Corporate and product informationWeb: sierrawireless.com Revision Number Release DateChanges 1.0January 23, 2020Document creation Rev 1.0 Jan 20441113583 Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Module Power States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 RF Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Conducted Tx Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Routing Constraints and Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 General Rules and Recommendations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 PCB Layout Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 PCB Specifications for the Application Board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Recommended PCB Land Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Routing Constraint…

Text truncated - open the document above for the full version.

053019-02a OEM Integration Manual Guidance – KDB 996369 D03 Section 2 Clear and Specific Instructions Describing the Conditions, Limitations, and Procedures for third-parties to use and/or integrate the module into a host device. Requirement Is this module intended for sale to third parties? ☒ - YES ☐ - No, If No, and LMA applies, the applicant can optionally choose to not make the following detailed info public. However there still needs to be basic integration instructions for a users manual and the information below must still be included in the operational description. If the applicant wishes to keep this info confidential, this will require a separate statement cover letter explaining the module is not for sale to third parties and that integration instructions are internal confidential documents. Items required to be in the manual – See KDB 996369 D03, Section 2 As of May 1, 2019, the FCC requires ALL the following information to be in the installation manual. Modular transmitter applicants should include information in their instructions for all these items indicating clearly when they are not applicable. For example information on trace antenna design could indicate “Not Applicable”. Also if a module is limited to only a grantees own products and not intended for sale to third parties, the user instructions may not need to be detailed and the following items can be placed in the operational description, but this should include a cover letter as cited above. 1. List of applicable FCC rules. KDB 996369 D03, Section 2.2 a. Only list rules related to the transmitter. ☒ - All Items shown to the left are provided in the Modular Integration Guide (or UM) for Full Modular Approval (MA) or LMA. ☐ - An LMA applies and is approved ONLY for use by the grantee in their own products, and not intended for sale to 3 rd parties as provided in a separate cover letter. Therefore the information shown to the left is found in the theory of operation. 2. Summarize the specific operational use conditions. KDB 996369 D03, Section 2.3 a. Conditions such as limits on antennas, cable loss, reduction of power for point to point systems, professional installation info 3. Limited Module Procedures. KDB 996369 D03, Section 2.4 a. Describe alternative means that the grantee uses to verify the host meets the necessary limiting conditions b. When RF exposure evaluation is necessary, state how control will be maintained such that compliance is ensured, such as Class II for new hosts, etc. 4. Trace antenna designs. KDB 996369 D03, Section 2.5 a. Layout of trace design, parts list, antenna, connectors, isolation requirements, tests for design verification, and production test procedures for ensuring compliance. If confidential, the method used to keep confidential must be identified and information provided in the operational description. 5. RF exposure considerations. KDB 996369 D03, Section 2.6 a. Clearly and explicitly state conditions that allow host manufacturers to use the module. Two types of instructions are necessary: first to the host manufacturer to define conditions (mobile, portable – xx cm from body) and second additional text needed to be provided to the end user in the host product manuals. 6. Antennas. KDB 996369 D03, Section 2.7 a. List of antennas included in the application and all applicable professional installer instructions when applicable. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc – note that “omni-directional” is not considered a type) 7. Label and compliance information. KDB 996369 D03, Section 2.8 a. Advice to host integrators that they need to provide a physical or e-label stating “Contains FCC ID: N7NRC76B“ with their finished product 8. Information on test modes and additional testing requirements. KDB 996369 D03, Section 2.9 a. Test modes that should be taken into consideration by host integrators including clarifications necessary for stand-alone and simultaneous configurations. b. Provide information on how to configure test modes for evaluation 9. Additional testing, Part 15 Subpart B disclaimer. KDB 996369 D03, Section 2.10 Sincerely, By: SENIOR MANAGER, CERTIFICATION DENIS CHABOT (Signature/Title 1 ) (Print name) 1 - Must be signed by applicant contact given for applicant on the FCC site, or by the authorized agent if an appropriate authorized agent letter has been provided. Letters should be placed on appropriate letterhead.

January 20, 2020 Federal Communications Commission Authorization and Standards Division 7435 Oakland Mills Road Columbia, MD 21046 To Whom It May Concern: Re: Confidentiality Request for FCC ID: N7NRC76B Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules and KDB 726920 D01 Confidentiality Request Procedures Detail, we hereby request that the exhibits listed below, submitted with our application for certification, be withheld from public disclosure. • Schematics • Block Diagram • Operation Description • Tune Up Procedure The above exhibits contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Furthermore, pursuant to Public Notice DA 04-1705 in order to comply with the marketing regulations in 47 CFR §2.803 and the importation rules in 47 CFR §2.1204, we request the following exhibits be withheld from public viewing for a short limited time of 180 days from the date of the Grant of Equipment Authorization, due to the sensitive business information: • User Manual • Internal Photos Best Regards, Denis CHABOT Senior Manager, Certification

Limited Modular Approval Checklist FCC ID: N7NRC76B Item Requirements EUT 1 The radio elements must have the radio frequency circuitry shielded Module RADIO elements are shielded. Please see submitted external photograph exhibits 2 The module must have buffered modulation/data inputs Module chipset design incorporates integrated buffer circuitry 3 The module must contain power supply regulation on the module Module chipset incorporates voltage regulation to transceiver circuitry 4 The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s) No applicable to licensed modules 5 The module must demonstrate compliance in a stand-alone configuration EUT conformance testing was performed in a standalone configuration 6 The licensed module must have a FCC ID label on the module itself. That FCC ID label must be visible through a window on the final device or it must be visible when an access panel, door or cover is easily removed. If not, a second label must be placed on the outside of the final device that contains the following text: Contains “FCC ID: N7NRC76B” Please refer to FCC ID label format. Labeling instruction has been provided in the user manual exhibit(s). 7 The module must comply with all specific rules applicable to the transmitter. The grantee must provide comprehensive instructions to explain compliance requirements The Module is compliant with all applicable FCC rules. Compliance requirements are stated in the user manual exhibit(s). 8 The module must comply with RF exposure requirements Compliance with RF exposure requirements is addressed in RF exposure report Sincerely, __________________________ By: Denis CHABOT Title: Senior Manager, Certification Company: Sierra Wireless Inc. Telephone: +852 2824 5222 e-mail: [email protected]

RC7611 – External photos

RC7611 – Internal photos

MPE Evaluation for RC7611 Radio Module January 19, 2020 Contents 1. Introduction..................................................................................................... 2 2. RF Exposure Limits and Equations ................................................................ 3 3. Stand-Alone Transmission ............................................................................. 5 4. Collocated Transmission ................................................................................ 6 5. Conclusion...................................................................................................... 7 1. Introduction In this application we seek modular approval for the RC7611 radio module for use in standalone and collocated simultaneous transmission under mobile and fixed configurations. This Maximum Permissive Exposure (MPE) report demonstrates compliance analysis for RC7611 radio module with FCC CFR 47 §2.1091 and IC RSS-102 for standalone and collocated transmission in the exposure conditions where a separation distance of at least 20 centimeters is normally maintained between the transmitter's radiating structure(s) and the body of the user or nearby persons. The MPE analysis is limited for US / Canada bands only. The general population/uncontrolled exposure limits are applicable to situations in which the general public may be exposed or in which persons who are exposed as a consequence of their employment may not be made fully aware of the potential for exposure or cannot exercise control over their exposure. 2. RF Exposure Limits and Equations FCC Limits: According to FCC OET Bulletin 65 Supplement C, the criteria listed in Table 1 shall be used to evaluate the environmental impact of human exposure to radio frequency (RF) radiation as specified in §1.1307. Table 1 : Limits for Maximum Permissible Exposure (MPE) IC Limits: IC has adopted the RF field strength limits established in Health Canada’s RF exposure guideline. The limits are shown in Table 2 below per RSS- 102. Table 2 : RF Field Strength Limits for Devices Used by the General Public (Uncontrolled Environment) In the frequency range of 300-6000 MHz, the IC limits are more stringent than the FCC limits. The MPE evaluation in this report will be based on the IC limits, so the deduced output power and antenna gain limits will guarantee compliance with both FCC and IC requirements. EQUATIONS: EIRP (dBm) = Conducted Power (dBm) + Antenna Gain (dBi) Power density is given by : S = EIRP / (4 π * D^2) where S = Power density (mW/cm^2) EIRP = Equivalent Isotropic Radiated Power (mW) D = Separation distance (cm) 3. Stand-Alone Transmission When RC7611 module transmits as a stand-alone mobile device, the source- based time-averaged EIRP is calculated by summing up conducted power and antenna gain. A 100% duty cycle is used for calculations to present a worse-case analysis. The antenna gains are chosen so that the resulted radiated power levels are within the limits specified by the FCC rules and IC Radio Standards Specifications (RSS). The IC exemption limits for routine RF exposure evaluation are calculated using the lowest frequency of the operating band presenting the most stringent limits. As shown in Table 2 below, the resulted EIRP are always below the IC exemption limits for all the operating modes. Operating Mode TX Freq Range (MHz) Max Time- Avg Cond Power (dBm) Max Time- Avg Cond Power (W) Max Ant Gain (dBi) Source- Based Time- Averaged Max EIRP (dBm) IC Exemption Limit (EIRP) (dBm) EIRP/ERP Limits LTE Band 2 1850 1910 24 0.25 6 30 33.50 2 W EIRP LTE Band 4 1710 1755 24 0.25 6 30 33.27 1 W EIRP LTE Band 5 824 849 24 0.25 6 30 31.10 6.3 W ERP LTE Band 12 699 716 24 0.25 6 30 30.61 3 W ERP LTE Band 13 777 787 24 0.25 6 30 30.93 3 W ERP LTE Band 14 788 798 24 0.25 6 30 30.97 3 W ERP LTE Band 25 1850 1915 24 0.25 6 30 33.50 3 W ERP LTE Band 26 814 849 24 0.25 6 30 31.06 3 W ERP LTE Band 66 1710 1780 24 0.25 6 30 33.27 3 W ERP LTE Band 71 663 698 24 0.25 6 30 30.45 3 W ERP Table 2: RC7611 Stand-Alone Transmission 4. Collocated Transmission When RC7611 module co-transmits with radio transmitter(s) as a mobile device, per KDB 447498 D01, simultaneous transmission MPE test exclusion applies when the sum of the MPE ratios for all simultaneous transmitting antennas incorporated in a host device, based on the calculated/estimated, numerically modeled or measured field strengths or power density, is ≤ 1.0. The evaluation here considers a WiMAX or WLAN transmitter, and a Bluetooth transmitter as collocated transmitters. Their radiated output power levels are listed in Table 3 below. The MPE ratio is defined by the ratio of power density to MPE limit. The sum of the MPE ratios is calculated as follows: ∑푀푃퐸 푅푎푡푖표 = Max (RC7611 MPE ratio) + Max (WLAN MPE ratio) + BT MPE Ratio + Max (WiGig MPE ratio) = 0.545+0.372+0.015+0.063=0.995 < 1.0 Operating Mode TX Freq Range (MHz) Max Time- Avg Cond Power (dBm) Max Time- Avg Cond Power (W) Max Ant Gain (dBi) Source- Based Time- Averaged Max EIRP Power Density @20 cm (W/m^2) IC MPE Limit (W/m2) IC PwrDensity MPE Ratio LTE Band 2 1850 1910 24 0.25 6 30 1.99 4.48 0.444 LTE Band 4 1710 1755 24 0.25 6 30 1.99 4.24 0.469 LTE Band 5 824 849 24 0.25 4 28 1.26 2.58 0.487 LTE Band 12 699 716 24 0.25 4 28 1.26 2.30 0.545 LTE Band 13 777 787 24 0.25 4 28 1.26 2.47 0.507 LTE Band 14 788 798 24 0.25 4 28 1.26 2.50 0.502 LTE Band 25 1850 1915 24 0.25 6 30 1.99 4.48 0.444 LTE Band 26 814 849 24 0.25 4 28 1.26 2.55 0.491 LTE Band 66 1710 1780 24 0.25 4 28 1.26 4.24 0.296 LTE Band 71 663 698 24 0.25 3 27 1.00 2.22 0.449 WLAN 2.4 GHz 2400 2500 30 1.99 5.35 0.372 WLAN 5 GHz 5150 5850 30 1.99 9.01 0.221 BT 2400 2500 16 0.08 5.35 0.015 WiGig 58320 62640 25 0.63 10.00 0.063 Table 3: RC7611 Collocated Transmission 5. Conclusion The analysis presented in this report concludes that the RC7611 radio module, when transmitting either in standalone or simultaneously with other co-located radio transmitters withi…

Text truncated - open the document above for the full version.

Report No.: 19B0422R-HPUSP50V00 Page: 1 of 1274 FCC Test Report Product Name : Module Trade Name : AirPrime Model No. : RC7611 FCC ID. : N7NRC76B Applicant : SIERRA WIRELESS (ASIA PACIFIC) LIMITED, TAIWAN BRANCH (HONG KONG) Address : 7F. (AB,E), NO. 1,3, YUANDONG RD., BANQIAO DIST., NEW TAIPEI CITY 22063 Taiwan Date of Receipt : Nov. 29, 2019 Issued Date : Jan. 22, 2020 Report No. : 19B0422R-HPUSP50V00 Report Version : V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of DEKRA Testing and Certification Co., Ltd. Report No.: 19B0422R-HPUSP50V00 Page: 2 of 1274 Test Report Certification Issued Date : Jan. 22, 2020 Report No. : 19B0422R-HPUSP50V00 Product Name : Module Applicant : SIERRA WIRELESS (ASIA PACIFIC) LIMITED, TAIWAN BRANCH (HONG KONG) Address : 7F. (AB,E), NO. 1,3, YUANDONG RD., BANQIAO DIST., NEW TAIPEI CITY 22063 Taiwan Manufacturer : SIERRA WIRELESS HONG KONG LIMITED Address : 6/F Enterprise Place, No.5 Science Park West Avenue, Hong Kong Science Park, Shatin, New Territories, Hong Kong Trade name : AirPrime Model No. : RC7611 FCC ID. : N7NRC76B EUT Voltage : DC 3.7V Testing Voltage : DC 3.7V Applicable Standard : FCC CFR Title 47 Part 22 Subpart H FCC CFR Title 47 Part 24 Subpart E FCC CFR Title 47 Part 27 Subpart L, Subpart F FCC CFR Title 47 Part 90 Subpart S ANSI/TIA-603-D Test Lab : Hsin Chu Laboratory Address : No.372-2, Sec. 4, Zhongxing Rd., Zhudong Township, Hsinchu County 310, Taiwan, R.O.C. TEL: +886-3-582-8001 / FAX: +886-3-582-8958 Test Result : Complied Documented By : ( Lyla Yang / Engineering Adm. Specialist ) Tested By : ( Clemens Fang / Senior Engineer ) Approved By : ( Louis Hsu / Deputy Manager ) Report No.: 19B0422R-HPUSP50V00 Page: 3 of 1274 Revision History Report No. Version Description Issued Date 19B0422R-HPUSP50V00 V1.0 Initial issue of report Jan. 22, 2020 Report No.: 19B0422R-HPUSP50V00 Page: 4 of 1274 TABLE OF CONTENTS Description Page 1. General Information ............................................................................................................. 6 1.1. EUT Description ................................................................................................................... 6 1.2. Mode of Operation ............................................................................................................... 7 1.3. Tested System Details ......................................................................................................... 8 1.4. Configuration of Tested System ........................................................................................... 8 1.5. EUT Exercise Software ........................................................................................................ 8 2. Technical Test ...................................................................................................................... 9 2.1. Summary of Test Result ....................................................................................................... 9 2.2. Test Environment ............................................................................................................... 18 2.3. List of Test Equipment........................................................................................................ 1 9 2.4. Uncertainty ......................................................................................................................... 22 3. RF Output Power ............................................................................................................... 23 3.1. Test Setup .......................................................................................................................... 23 3.2. Test Procedure ................................................................................................................... 23 3.3. Test Method ....................................................................................................................... 23 3.4. Test Result ......................................................................................................................... 24 4. Occupied Bandwidth ........................................................................................................ 116 4.1. Test Setup ........................................................................................................................ 116 4.2. Test Procedure ................................................................................................................. 116 4.3. Test Method ..................................................................................................................... 116 4.4. Test Result ....................................................................................................................... 117 5. Peak To Average Ratio .................................................................................................... 458 5.1. Test Setup ........................................................................................................................ 458 5.2. Test Procedure ................................................................................................................. 458 5.3. Test Method ..................................................................................................................... 458 5.4. Limit ................................................................................................................................. 458 5.5. Test Result ....................................................................................................................... 459 6. Spurious Emissions ......................................................................................................... 610 6.1. Test Setup ........................................................................................................................ 610 6.2. Tes…

Text truncated - open the document above for the full version.

Report No.: 19B0422R-HPUSP50V00 Page: 193 of 1274 Product Module Test Item Occupied Bandwidth Test Mode Mode 2: LTE Band 4 Date of Test 2019/12/10~2019/12/11 Test Site SR12-H Temperature (°C) 23.0~24.0°C Humidity (%RH) 56~59%RH LTE Band 4_1RB Low/high Band width (MHz) Modulation Frequency (MHz) Measure Level (MHz) Limit (MHz) 26dB BW 99% BW 1.4M QPSK 1710.7 0.334 0.213 N/A 1732.5 0.319 0.207 N/A 1754.3 0.320 0.213 N/A 16-QAM 1710.7 0.343 0.217 N/A 1732.5 0.343 0.221 N/A 1754.3 0.324 0.212 N/A 3M QPSK 1711.5 0.326 0.213 N/A 1732.5 0.333 0.211 N/A 1753.5 0.315 0.209 N/A 16-QAM 1711.5 0.302 0.211 N/A 1732.5 0.316 0.211 N/A 1753.5 0.339 0.216 N/A 5M QPSK 1712.5 0.339 0.221 N/A 1732.5 0.370 0.229 N/A 1752.2 0.359 0.225 N/A 16-QAM 1712.5 0.404 0.239 N/A 1732.5 0.348 0.214 N/A 1752.2 0.372 0.233 N/A 10M QPSK 1715 0.351 0.227 N/A 1732.5 0.380 0.238 N/A 1750 0.375 0.225 N/A 16-QAM 1715 0.386 0.230 N/A 1732.5 0.379 0.237 N/A 1750 0.410 0.252 N/A Report No.: 19B0422R-HPUSP50V00 Page: 194 of 1274 LTE Band 4_1RB Low/high Band width (MHz) Modulation Frequency (MHz) Measure Level (MHz) Limit (MHz) 26dB BW 99% BW 15M QPSK 1717.5 0.399 0.238 N/A 1732.5 0.396 0.248 N/A 1747.5 0.373 0.257 N/A 16-QAM 1717.5 0.386 0.259 N/A 1732.5 0.428 0.260 N/A 1747.5 0.404 0.261 N/A 20M QPSK 1720 0.406 0.255 N/A 1732.5 0.404 0.254 N/A 1745 0.378 0.253 N/A 16-QAM 1720 0.407 0.263 N/A 1732.5 0.424 0.267 N/A 1745 0.410 0.256 N/A Report No.: 19B0422R-HPUSP50V00 Page: 195 of 1274 LTE Band 4_Full RB Band width (MHz) Modulation Frequency (MHz) Measure Level (MHz) Limit (MHz) 26dB BW 99% BW 1.4M QPSK 1710.7 1.281 1.103 N/A 1732.5 1.307 1.102 N/A 1754.3 1.284 1.093 N/A 16-QAM 1710.7 1.285 1.094 N/A 1732.5 1.278 1.094 N/A 1754.3 1.294 1.099 N/A 3M QPSK 1711.5 2.913 2.685 N/A 1732.5 2.946 2.684 N/A 1753.5 2.927 2.686 N/A 16-QAM 1711.5 2.946 2.683 N/A 1732.5 2.933 2.680 N/A 1753.5 2.940 2.681 N/A 5M QPSK 1712.5 4.942 4.483 N/A 1732.5 4.916 4.468 N/A 1752.2 4.927 4.481 N/A 16-QAM 1712.5 4.855 4.470 N/A 1732.5 4.949 4.477 N/A 1752.2 4.933 4.482 N/A 10M QPSK 1715 9.614 8.908 N/A 1732.5 9.707 8.926 N/A 1750 9.697 8.925 N/A 16-QAM 1715 9.632 8.912 N/A 1732.5 9.619 8.926 N/A 1750 9.638 8.911 N/A Report No.: 19B0422R-HPUSP50V00 Page: 196 of 1274 LTE Band 4_Full RB Band width (MHz) Modulation Frequency (MHz) Measure Level (MHz) Limit (MHz) 26dB BW 99% BW 15M QPSK 1717.5 14.590 13.398 N/A 1732.5 14.660 13.401 N/A 1747.5 14.400 13.363 N/A 16-QAM 1717.5 14.500 13.381 N/A 1732.5 14.550 13.415 N/A 1747.5 14.500 13.375 N/A 20M QPSK 1720 18.980 17.824 N/A 1732.5 19.300 17.838 N/A 1745 18.950 17.802 N/A 16-QAM 1720 19.070 17.836 N/A 1732.5 19.190 17.849 N/A 1745 19.110 17.815 N/A Report No.: 19B0422R-HPUSP50V00 Page: 197 of 1274 B4_CH19957_1.4M_QPSK_1RB0 B4_CH19957_1.4M_QPSK_6RB0 Report No.: 19B0422R-HPUSP50V00 Page: 198 of 1274 B4_CH19957_1.4M_16-QAM_1RB0 B4_CH19957_1.4M_16-QAM_6RB0 Report No.: 19B0422R-HPUSP50V00 Page: 199 of 1274 B4_CH20175_1.4M_QPSK_1RB0 B4_CH20175_1.4M_QPSK_6RB0 Report No.: 19B0422R-HPUSP50V00 Page: 200 of 1274 B4_CH20175_1.4M_16-QAM_1RB0 B4_CH20175_1.4M_16-QAM_6RB0 Report No.: 19B0422R-HPUSP50V00 Page: 201 of 1274 B4_CH20393_1.4M_QPSK_1RB5 B4_CH20393_1.4M_QPSK_6RB0 Report No.: 19B0422R-HPUSP50V00 Page: 202 of 1274 B4_CH20393_1.4M_16-QAM_1RB5 B4_CH20393_1.4M_16-QAM_6RB0 Report No.: 19B0422R-HPUSP50V00 Page: 203 of 1274 B4_CH19965_3M_QPSK_1RB0 B4_CH19965_3M_QPSK_15RB0 Report No.: 19B0422R-HPUSP50V00 Page: 204 of 1274 B4_CH19965_3M_16-QAM_1RB0 B4_CH19965_3M_16-QAM_15RB0 Report No.: 19B0422R-HPUSP50V00 Page: 205 of 1274 B4_CH20175_3M_QPSK_1RB0 B4_CH20175_3M_QPSK_15RB0 Report No.: 19B0422R-HPUSP50V00 Page: 206 of 1274 B4_CH20175_3M_16-QAM_1RB0 B4_CH20175_3M_16-QAM_15RB0 Report No.: 19B0422R-HPUSP50V00 Page: 207 of 1274 B4_CH20385_3M_QPSK_1RB14 B4_CH20385_3M_QPSK_15RB0 Report No.: 19B0422R-HPUSP50V00 Page: 208 of 1274 B4_CH20385_3M_16-QAM_1RB14 B4_CH20385_3M_16-QAM_15RB0 Report No.: 19B0422R-HPUSP50V00 Page: 209 of 1274 B4_CH19975_5M_QPSK_1RB0 B4_CH19975_5M_QPSK_25RB0 Report No.: 19B0422R-HPUSP50V00 Page: 210 of 1274 B4_CH19975_5M_16-QAM_1RB0 B4_CH19975_5M_16-QAM_25RB0 Report No.: 19B0422R-HPUSP50V00 Page: 211 of 1274 B4_CH20175_5M_QPSK_1RB0 B4_CH20175_5M_QPSK_25RB0 Report No.: 19B0422R-HPUSP50V00 Page: 212 of 1274 B4_CH20175_5M_16-QAM_1RB0 B4_CH20175_5M_16-QAM_25RB0 Report No.: 19B0422R-HPUSP50V00 Page: 213 of 1274 B4_CH20372_5M_QPSK_1RB24 B4_CH20372_5M_QPSK_2…

Text truncated - open the document above for the full version.