N89-CB001AHP 802.11g Printer Card

CB001A HP 802.11g printer card User’s Manual Rev 0.1 HP 802.11g printer card User’s Manual 2 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IMPORTANT NOTE: FCC / IC Radiation Exposure Statement: This device complies with FCC RF Exposure limits set forth for an uncontrolled environment, under 47 CFR 2.1093 paragraph (d)(2). This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device was tested for typical lap held conditions that may occur during normal notebook and PDA use. To comply with FCC RF exposure requirements the user shall use this product only in intended application as documented in this manual. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. Industry Canada Statement Operation is subject to the following two conditions: 1) This device may not cause interference and 2) This device must accept any interference, including interference that may cause undesired operation of the device HP 802.11g printer card User’s Manual 3 About this manual This User’s Manual describes how to install and operate your Compact Flash Wireless LAN Card. Please read this manual before you install the product. This manual includes the following topics: ¾ Product description and features. ¾ Software installation procedure. ¾ Specification HP 802.11g printer card User’s Manual 4 Table of Contents About this manual............................................................... 3 Chapter 1 - Introduction ................................................... 5 Features............................................................................................ 5 What is Wireless LAN?.................................................................. 6 Wireless LAN Modes...................................................................... 7 Notes on Wireless LAN Configuration........................................ 8 Chapter 2 – Driver Installation for Windows .................... 9 Driver installation for Windows 2000 ................................................... 9 Driver installation for Windows XP .................................................... 13 Appendix A – Specifications........................................... 16 HP 802.11g printer card User’s Manual 5 Chapter 1 - Introduction The CB001A CF Card gives you the freedom to work your way, from wherever you want. An enhanced 802.11g featuring advanced silicon chip design from Marvell capable of delivering data transfer rates up to 54Mbps. Features • Compact Flash Type-I form factor. • IEEE 802.11g compatible. • Backward compatible with IEEE 802.11b standard. • Wire-free access to networked resources from anywhere beyond the desktop. • Delivers data rate up to 54 Mbps. • 802.11g: Dynamically shifts between 54, 48, 36, 24, 18, 12, 9 and 6 Mbps network speed, based on signal strength, for maximum availability and reliability of connection. • 802.11b: Dynamically shifts between 11M, 5.5M, 2M, and 1 Mbps network speed, based on signal strength, for maximum availability and reliability of connection. • Allows users move between Access Points without resetting their connection reconfiguration. • Built-In PCB antenna with diversity design (Two antennas required). • Support advanced power management and power saving mode. • Low CPU utilization through scatter gathers bus-mastering DMA architecture. • Uses 2.4GHz frequency band, which complies with worldwide requirement. • Fallback rat algorithm that sets the optimum transmission rate based on actual signal-to-noise ratio and packet loss information • Supports most popular operating systems: Window 98SE/2000/ME/XP and WinCE/Linux. • Ensures great security by providing the 64/128 bits Wired Equivalent Privacy (WEP) and WiFi Protected Access (WPA) defined in the IEEE standard. • 802.11i and WPA2 Support • 802.11e (WMM) Support • Future driver upgradeable HP 802.11g printer card User’s Manual 6 What is Wireless LAN? Wireless Local Area Network (WLAN) systems offer a great number of advantages over traditional wired systems. WLAN is flexible and easy to setup and manage. They are also more economical than wired LAN systems. Using radio frequency (RF) technology, WLAN transmit and receive data through the air. WLAN combine data connectivity with user mobility. For example, users can roam from a conference room to their office without being disconnected from the LAN. Using WLAN, users can conveniently access-…

Text truncated - open the document above for the full version.

Page 1 CONSTRUCTION PHOTOS OF EUT Page 2

(Fig. 1) FCC ID: N89-CB001A FCC LABEL LOCATION The label will be permanently affixed at a conspicuous location on the device. Label

Page 3 Page 4 Page 5 Page 6 Page 7

FCC ID: N89-CB001A Report No. RF940913H06 Operational Description This device is a HP 802.11g printer card, the maximum data rate could be up to 54Mbps which OFDM technique will be applied. If the signal to noise radio is too poor which could not support 54Mbps, the 11Mbps data rate with CCK technique will be applied. The transmitter of the EUT (HP 802.11g printer card) is powered by host equipment. The antenna type used in this product is Chip Antenna without connector. The other instruction, please have a look at the users manual.

FCC ID: N89-CB001A Report no.: SA940913H061Report Format Version 2.0.2 SAR TEST REPORT REPORT NO.: SA940913H06 MODEL NO.: CB001A RECEIVED: Jul.07, 2005 TESTED: Jul. 08, 2005 ~ Nov. 16, 2005 ISSUED: Nov. 17, 2005 APPLICANT: CyberTAN Technology, Inc. ADDRESS: No.99, Park Avenue III, Science-based Industrial Park, Hsinchu, Taiwan 308,R.O.C. ISSUED BY: Advance Data Technology Corporation LAB ADDRESS: No. 47, 14 th Ling, Chia Pau Tsuen, Lin Kou Hsiang 244, Taipei Hsien, Taiwan, R.O.C. TEST LOCATION: No. 19, Hwa Ya 2 nd Rd., Kwei Shan Hsiang, Taoyuan Hsien 333, Taiwan, R.O.C. This test report consists of 39 pages in total except Appendix. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. 0528 ILAC MRA No. 2177-01 FCC ID: N89-CB001A Report no.: SA940913H062Report Format Version 2.0.2 TABLE OF CONTENTS 1.CERTIFICATION..................................................................................................................3 2.GENERAL INFORMATION...................................................................................................4 2.1GENERAL DESCRIPTION OF EUT................................................................................4 2.2GENERAL DESCRIPTION OF APPLIED STANDARDS..................................................5 2.3GENERAL INOFRMATION OF THE SAR SYSTEM........................................................5 2.4GENERAL DESCRIPTION OF THE SPATIAL PEAK SAR EVALUATION........................9 3.DESCRIPTION OF SUPPORT UNITS................................................................................13 4.DESCRIPTION OF TEST MODES AND CONFIGURATIONS..............................................14 4.1.DESCRIPTION OF ANTENNA LOCATION...................................................................14 4.2.DESCRIPTION OF ASSESSMENT POSITION.............................................................15 4.3.DESCRIPTION OF TEST MODE..................................................................................16 4.4.SUMMARY OF TEST RESULTS...................................................................................16 5.TEST RESULTS.................................................................................................................17 5.1TEST PROCEDURES..................................................................................................17 5.2MEASURED SAR RESULTS........................................................................................19 5.3SAR LIMITS.................................................................................................................22 5.4RECIPES FOR TISSUE SIMULATING LIQUIDS...........................................................23 5.5TEST EQUIPMENT FOR TISSUE PROPERTY............................................................25 6.SYSTEM VALIDATION.......................................................................................................27 6.1TEST EQUIPMENT......................................................................................................27 6.2TEST PROCEDURE.....................................................................................................28 6.3VALIDATION RESULTS................................................................................................30 6.4SYSTEM VALIDATION UNCERTAINTIES....................................................................31 7.MEASUREMENT SAR PROCEDURE UNCERTAINTIES....................................................32 7.1.PROBE CALIBRATION UNCERTAINTY.......................................................................32 7.2.ISOTROPY UNCERTAINTY.........................................................................................33 7.3.BOUNDARY EFFECT UNCERTAINTY.........................................................................33 7.4.PROBE LINEARITY UNCERTAINTY............................................................................34 7.5.READOUT ELECTRONICS UNCERTAINTY................................................................34 7.6.RESPONSE TIME UNCERTAINTY..............................................................................34 7.7.INTEGRATION TIME UNCERTAINTY..........................................................................35 7.8.PROBE POSITIONER MECHANICAL TOLERANCE....................................................36 7.9.PROBE POSITIONING.................................................................................................36 7.10.PHANTOM UNCERTAINTY.........................................................................................37 7.11.DASY4 UNCERTAINTY BUDGET................................................................................38 8.INFORMATION ON THE TESTING LABORATORIES.........................................................39 APPENDIX A: TEST CONFIGURATIONS AND TEST DATA APPENDIX B: ADT SAR MEASUREMENT SYSTEM APPENDIX C: PHOTOGRAPHS OF SYSTEM VALIDATION APPENDIX D: SYSTEM CERTIFICATE & CALIBRATION FCC ID: N89-CB001A Report no.: SA940913H063Report Format Version 2.0.2 1. CERTIFICATION PRODUCT: HP 802.11g printer card MODEL: CB001A BRAND: HP APPLICANT: CyberTAN Technology, Inc. TEST SAMPLE: ENGINEERING SAMPLE STANDARDS:FCC Part 2 (Section 2.1093), RSS-102 FCC OET Bulletin 65, Supplement C (01-01) The above equipment (model: CB001A) is identical to model no. WL54-CF which has been tested by Advance Data Technology Corporation on Jul. 08, 2005, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample’s EMC characteristics under the conditions specified in this report. PREPARED BY …

Text truncated - open the document above for the full version.

FCC ID: N89-CB001A Report No.: RF940913H061Report Format Version 2.0.2 FCC TEST REPORT REPORT NO.: RF940913H06 MODEL NO.: CB001A RECEIVED: May 10, 2005 TESTED: May 10, 2005 & Sep. 26, 2005(only for Radiated Test (Below 1 GHz) ISSUED: Oct. 07, 2005 APPLICANT: CyberTAN Technology, Inc. ADDRESS: No.99, Park Avenue III, Science-based Industrial Park, Hsinchu, Taiwan 308,R.O.C. ISSUED BY: Advance Data Technology Corporation LAB LOCATION: No. 81-1, Lu Liao Keng, 9 Ling, Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien, Taiwan, R.O.C. This test report consists of 62 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CNLA, A2LA or any government agencies. The test results in the report only apply to the tested sample. The test results in this report are traceable to the national or international standards. 0536 No. 2177-01 ILAC MRA FCC ID: N89-CB001A Report No.: RF940913H062Report Format Version 2.0.2 Table of Contents 1CERTIFICATION...........................................................................................4 2SUMMARY OF TEST RESULTS...................................................................5 3GENERAL INFORMATION............................................................................6 3.1GENERAL DESCRIPTION OF EUT..............................................................6 3.2DESCRIPTION OF TEST MODES................................................................7 3.3TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL:...............7 3.4GENERAL DESCRIPTION OF APPLIED STANDARDS................................9 3.5DESCRIPTION OF SUPPORT UNITS........................................................10 3.6CONFIGURATION OF SYSTEM UNDER TEST.........................................10 4TEST TYPES AND RESULTS.....................................................................11 4.1CONDUCTED EMISSION MEASUREMENT..............................................11 4.1.1LIMITS OF CONDUCTED EMISSION MEASUREMENT............................11 4.1.2TEST INSTRUMENTS.................................................................................11 4.1.3TEST PROCEDURES.................................................................................12 4.1.4TEST SETUP..............................................................................................12 4.1.5EUT OPERATING CONDITIONS................................................................13 4.1.6TEST RESULTS..........................................................................................14 4.2RADIATED EMISSION MEASUREMENT...................................................16 4.2.1LIMITS OF RADIATED EMISSION MEASUREMENT.................................16 4.2.2TEST INSTRUMENTS.................................................................................17 4.2.3TEST PROCEDURES.................................................................................18 4.2.4TEST SETUP..............................................................................................19 4.2.5EUT OPERATING CONDITIONS................................................................19 4.2.6TEST RESULTS..........................................................................................20 4.2.7TEST RESULTS – DSSS.............................................................................21 4.2.8TEST RESULTS – OFDM............................................................................24 4.36DB BANDWIDTH MEASUREMENT..........................................................27 4.3.1LIMITS OF 6DB BANDWIDTH MEASUREMENT........................................27 4.3.2TEST INSTRUMENTS.................................................................................27 4.3.3TEST PROCEDURE....................................................................................28 4.3.4TEST SETUP..............................................................................................28 4.3.5EUT OPERATING CONDITIONS................................................................28 4.3.6TEST RESULTS – DSSS.............................................................................29 4.3.7TEST RESULTS – OFDM............................................................................32 4.4MAXIMUM PEAK OUTPUT POWER..........................................................35 FCC ID: N89-CB001A Report No.: RF940913H063Report Format Version 2.0.2 4.4.1LIMITS OF MAXIMUM PEAK OUTPUT POWER MEASUREMENT...........35 4.4.2TEST INSTRUMENTS.................................................................................35 4.4.3TEST PROCEDURES.................................................................................36 4.4.4TEST SETUP..............................................................................................36 4.4.5EUT OPERATING CONDITIONS................................................................36 4.4.6TEST RESULTS – DSSS.............................................................................37 4.4.7TEST RESULTS – OFDM............................................................................38 4.5POWER SPECTRAL DENSITY MEASUREMENT......................................39 4.5.1LIMITS OF POWER SPECTRAL DENSITY MEASUREMENT....................39 4.5.2TEST INSTRUMENTS.................................................................................39 4.5.3TEST PROCEDURE....................................................................................40 4.5.4TEST SETUP..............................................................................................40 4.5.5EUT OPERATING CONDITIONS................................................................40 4.5.6TEST RESULTS – DSSS.............................................................................41 4.5.7TEST RESULTS – OFDM...............................................…

Text truncated - open the document above for the full version.

FCC ID: N89-CB001A Report No.: RF940913H0658Report Format Version 2.0.2 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST 940913H06 FCC ID: N89-CB001A Report No.: RF940913H0659Report Format Version 2.0.2 940913H06 FCC ID: N89-CB001A Report No.: RF940913H0660Report Format Version 2.0.2 RADIATED EMISSION TEST 940913H06 940913H06 FCC ID: N89-CB001A Report No.: RF940913H0661Report Format Version 2.0.2 940913H06