N89-MM300CBluetooth 2.0+ EDR Module

MM300-C / Bluetooth 2.0+ EDR Module MM300-C Bluetooth 2.0+ EDR Module User Manual Rev 0.1 MM300-C / Bluetooth 2.0+ EDR Module National Communications Commission Interference Statement This equipment includes wireless RF module, and must be labeled in a visible area with the following: Contains NCC ID: XXXyyyLPDzzzz-x MM300-C / Bluetooth 2.0+ EDR Module ii Table of contents Introduction................................................... 1 Install Bluetooth............................................. 2 MM300-C / Bluetooth 2.0+ EDR Module 1 Chapter 1 Introduction Thank you for using the Bluetooth Module. The MM300-C is a Bluetooth adapter that works on Bluetooth operation everywhere in the world. It is Bluetooth 2.0+ EDR. MM300-C can give users of laptops, note- books, tablet PCs, and other mobile computing devices access anywhere in the world through any Bluetooth network devices. Able to provide Bluetooth real world throughput. The MM300-C provides the freedom to work as you wish, wherever you wish, using whatever kind of Bluetooth application you wish to use. It is ready to work “out of the box” in any embedded device or in any computer running Microsoft® Windows Vista, or XP. The MM300-C Module is truly a “must-have” for every productivity-sensitive laptop, notebook, or tab- let PC user and any bandwidth-sensitive embedded design. Features and Benefits • Seamless Wireless Connectivity Bluetooth v2.0+EDR supports the use of most recent user-end devices. MM300-C / Bluetooth 2.0+ EDR Module 2 Chapter 2 Install Bluetooth MM300-C also support Bluetooth function. Below shows how to install Bluetooth device. 4.1 How to install Bluetooth device 3 MM300-C / Bluetooth 2.0+ EDR Module 4 5 MM300-C / Bluetooth 2.0+ EDR Module 6 Appendix A 1. Common Physical Layer Specifications Table 1: Common Physical Layer Specifications Operating Frequency 2402MHz to 2480MHz Bluetooth Tx Power (Typical) 2±2dBm Bluetooth Rx Sensitivity (typical) -42dBm Carrier Spacing 1.0MHz Channel 79 Duplexing TDD Symbol Rate 1Mbps (GFSK) 2Mbps (π/4-DQPSK) 3Mbps (8DPSK) Modulation Method GFSK BT = 0.5 ?/4DQPSK 8DPSK Reference Oscillator 26MHz (built in) RF input and output impedance Nominal 50 ohm Main Chip CSR BC41B143A Dimensions 25.0 x 12.0 x 2.6 mm (typical) GP Compliance Yes FCC Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Change or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. RF exposure warning: This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance."

Federal Communications Commission February 25, 2008 Authorization and Evaluation Division ATTESTATION FCC ID: N89-MM300C Product: Bluetooth 2.0+ EDR Module Model: MM300-C We don't provide any controls or software to allow operation outside the USA frequency band when we sell this product in USA. Best Regards, ------------------------------------------------ Chiu Wen Chuan CyberTAN Technology, Inc. Tel: 886-3-577-7777 E-mail: [email protected]

RF_734_00, Issue 1 Modular Approval Request FCC (per DA 00-1407) FCC ID: _ N89-MM300C ___ Items to be covered Answer from applicant 1. The modular transmitter must have its own RF shielding. Yes 2. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will comply with Part 15 requirements under conditions of excessive data rates or over-modulation. Yes 3. The modular transmitter must have its own power supply regulation. Yes 4. The modular transmitter must comply with the antenna requirements of Section 15.203 and 15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler (at all connections between the module and the antenna, including the cable).. Yes 5. The modular transmitter must be tested in a stand-alone configuration, i.e., the module must not be inside another device during testing. This is intended to demonstrate that the module is capable of complying with Part 15 emission limits regardless of the device into which it is eventually installed. Yes 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. Yes 7. The modular transmitter must comply with any specific rule or operating requirements applicable to the transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. For example, there are very strict operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. Yes 8. The modular transmitter must comply with any applicable RF exposure requirements. For example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and millimeter wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Yes Note: If compliance with one or more of the numbered requirements, listed above, cannot be demonstrated, it may be possible to obtain a “Limited Modular Approval” (LMA). Name and surname of applicant (or authorized representative): __________________ Date: 2008-02-26 Signature: _______

Subject: Request for Confidentiality Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: N89-MM300C Pursuant to Sections 0.457 and 0.459 of the Commission’s Rules, we hereby request confidential treatment of information accompanying this application as outlined below: Exhibit Type File Name Block Diagram (N89-MM300C) BlkDia Schematics (N89-MM300C) Schem Theory of Operation (N89-MM300C) OpDes The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, ------------------------------------------------ Chiu Wen Chuan CyberTAN Technology, Inc. Tel: 886-3-577-7777 E-mail: [email protected]

We Name: CyberTAN Technology, Inc. Address: 99 Park Avenue 3, Science Park City: Hsinchu 308 Country: Taiwan, R.O.C. Declare that: Name: QuieTek Corp. Address: Fl.2, No.345, Xin-hu 2 nd Rd., Nei-hu District City: Taipei Country Taiwan R.O.C. is authorized to apply for Certification of the following product(s): Product description: Bluetooth 2.0+ EDR Module Type designation: MM300-C Trademark: CyberTAN FCC ID: N89-MM300C on our behalf. ------------------------------------------------ Chiu Wen Chuan CyberTAN Technology, Inc. Tel: 886-3-577-7777 E-mail: [email protected]

Report No： 081090R-RFUSP06V01-1 Page: 97 of 99 Attachement ¾ EUT Photograph (1) EUT Photo (2) EUT Photo

Report No： 081090R-RFUSP06V01-1 Page: 98 of 100 (3) EUT Photo (4) EUT Photo Report No： 081090R-RFUSP06V01-1 Page: 99 of 100 (5) EUT Photo Report No： 081090R-RFUSP06V01-1 Page: 100 of 100 (6) EUT Photo (7) EUT Photo

FCC ID.: N89-MM300C FCC ID AND DoC Label The FCC ID and DoC Label will be placed on the equipment as shown in the photograph below. Bluetooth 2.0+ EDR Module Model No.: MM300-C F F C C C C I I D D : : N N 8 8 9 9 - - M M M M 3 3 0 0 0 0 C C This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. S/N: Made in Taiwan Trade name: CyberTAN Model number.: MM300-C

Report No： 081090R-RFUSP06V01-1 Page: 98 of 99 (3) EUT Photo (4) EUT Photo Report No： 081090R-RFUSP06V01-1 Page: 99 of 99 (5) EUT Photo (6) EUT Photo

Report No： 081090R-RFUSP06V01-1 Page: 97 of 100 Attachement ¾ EUT Photograph (1) EUT Photo (2) EUT Photo

Report No. 081090R-RFUSP06V01-Exp-1 Page: 1 of 5 RF Exposure Evaluation declaration Product Name ：Bluetooth 2.0+ EDR Module Model No. ：MM300-C FCC ID. ：N89-MM300C Applicant : CyberTAN Technology, Inc. Address : 99 Park Avenue 3, Science Park Hsinchu 308, Taiwan, R.O.C. Date of Receipt : 2008/01/06 Date of Declaration : 2008/02/26 Report No. : 081090R-RFUSP06V01-Exp-1 Version : V1.0 The declaration results relate only to the samples calculated. The declaration shall not be reproduced except in full without the written approval of QuieTek Corporation. Report No. 081090R-RFUSP06V01-Exp-1 Page: 2 of 5 1. RF Exposure Evaluation 1.1. Limits According to FCC 1.1310: The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in 1.1307(b) LIMITS FOR MAXIMUM PERMISSIBLE EXPOSURE (MPE) Frequency Range (MHz) Electric Field Strength (V/m) Magnetic Field Strength (A/m) Power Density (mW/cm 2 ) Average Time (Minutes) (A) Limits for Occupational/ Control Exposures 300-1500 -- -- F/300 6 1500-100,000 -- -- 5 6 (B) Limits for General Population/ Uncontrolled Exposures 300-1500 -- -- F/1500 6 1500-100,000 -- -- 1 30 F= Frequency in MHz Friis Formula Friis transmission formula: Pd = (Pout*G)/(4*pi*r 2 ) Where Pd = power density in mW/cm 2 Pout = output power to antenna in mW G = gain of antenna in linear scale Pi = 3.1416 R = distance between observation point and center of the radiator in cm Pd id the limit of MPE, 1 mW/cm 2 . If we know the maximum gain of the antenna and the total power input to the antenna, through the calculation, we will know the distance r where the MPE limit is reached. 1.2. Test Procedure Software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest channel individually. The temperature and related humidity: 18°Cand 78％ RH. Report No. 081090R-RFUSP06V01-Exp-1 Page: 3 of 5 1.3. Test Result of RF Exposure Evaluation Product Bluetooth 2.0+ EDR Module Test Mode Mode 1: Transmit Test Condition RF Exposure Evaluation Antenna Gain Antenna Gain: The maximum Gain measured in fully anechoic chamber is 2.51dBi or 1.782 in linear scale. Output Power into Antenna & RF Exposure Evaluation Distance: 1M-GFSK Modulation, PRBS Packet Type Bluetooth Function Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density at R = 20 cm (mW/cm 2 ) 1 2402.00 2.4889 0.00088 6 2441.00 2.1478 0.00076 11 2480.00 2.1232 0.00075 The power density Pd (4th column) at a distance of 20 cm calculated from the Friis transmission formula is far below the limit of 1 mW/cm 2 . Report No. 081090R-RFUSP06V01-Exp-1 Page: 4 of 5 Product Bluetooth 2.0+ EDR Module Test Mode Mode 1: Transmit Test Condition RF Exposure Evaluation Antenna Gain Antenna Gain: The maximum Gain measured in fully anechoic chamber is 2.51dBi or 1.782 in linear scale. Output Power into Antenna & RF Exposure Evaluation Distance: 2M-pi/4 Modulation, PRBS Packet Type Bluetooth Function Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density at R = 20 cm (mW/cm 2 ) 1 2402.00 1.4723 0.00052 6 2441.00 1.4355 0.00051 11 2480.00 1.2618 0.00045 The power density Pd (4th column) at a distance of 20 cm calculated from the Friis transmission formula is far below the limit of 1 mW/cm 2 . Report No. 081090R-RFUSP06V01-Exp-1 Page: 5 of 5 Product Bluetooth 2.0+ EDR Module Test Mode Mode 1: Transmit Test Condition RF Exposure Evaluation Antenna Gain Antenna Gain: The maximum Gain measured in fully anechoic chamber is 2.51dBi or 1.782 in linear scale. Output Power into Antenna & RF Exposure Evaluation Distance: 3M-8DPSK Modulation, PRBS Packet Type Bluetooth Function Channel Channel Frequency (MHz) Output Power to Antenna (mW) Power Density at R = 20 cm (mW/cm 2 ) 1 2402.00 1.4125 0.00050 6 2441.00 1.4421 0.00051 11 2480.00 1.2647 0.00045 The power density Pd (4th column) at a distance of 20 cm calculated from the Friis transmission formula is far below the limit of 1 mW/cm 2 .

Report No： 081090R-RFUSP06V01-1 Page: 1 of 99 Test Report Product Name ：Bluetooth 2.0+ EDR Module Model No. ：MM300-C FCC ID. ：N89-MM300C Applicant ： CyberTAN Technology, Inc. Address ： 99 Park Avenue 3, Science Park Hsinchu 308, Taiwan, R.O.C. Date of Receipt：2008/01/06 Issued Date ：2008/02/26 Report No. ：081090R-RFUSP06V01 Version ：V1.0 The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Report No： 081090R-RFUSP06V01-1 Page: 2 of 99 Test Report Certification Issued Date : 2008/02/26 Report No. : 081090R-RFUSP06V01-1 Product Name ： Bluetooth 2.0+ EDR Module Applicant ： CyberTAN Technology, Inc. Address ： 99 Park Avenue 3, Science Park Hsinchu 308, Taiwan, R.O.C. Manufacturer ： Foxconn Technology Group- Ambit Microsystems (Zhongshan)LTD. Model No. ： MM300-C FCC ID. ： N89-MM300C Rated Voltage : AC 120 V / 60 Hz EUT Voltage : Power by PC Trade Name ： CyberTAN Applicable Standard ： FCC CFR Title 47 Part 15 Subpart C Section 15.247:2006 Test Result ： Complied The test results relate only to the samples tested. The test report shall not be reproduced except in full without the written approval of QuieTek Corporation. Documented By ： ( Carol Tsai / Adm. Specialist ) Tested By ： ( Lucia Lu / Assistant Engineer ) Approved By ： ( Roy Wang / Manager ) Report No： 081090R-RFUSP06V01-1 Page: 3 of 99 TABLE OF CONTENTS Description Page 1. General Information ..................................................................................................... 5 1.1. EUT Description ............................................................................................................. 5 1.2. Operational Description .................................................................................................. 7 1.3. Test Mode ....................................................................................................................... 8 1.4. Tested System Details .................................................................................................... 9 1.5. Configuration of tested System .................................................................................... 10 1.6. EUT Exercise Software ................................................................................................ 11 1.7. Test Facility................................................................................................................... 12 2. Conducted Emission.................................................................................................. 14 2.1. Test Equipment............................................................................................................. 14 2.2. Test Setup .................................................................................................................... 14 2.3. Limits ............................................................................................................................ 15 2.4. Test Procedure ............................................................................................................. 15 2.5. Test Specification.......................................................................................................... 15 2.6. Test Result.................................................................................................................... 16 2.7. Test Photo .................................................................................................................... 20 3. Peak Power Output .................................................................................................... 21 3.1. Test Equipment............................................................................................................. 21 3.2. Test Setup .................................................................................................................... 21 3.3. Test procedures ............................................................................................................ 21 3.4. Limits ............................................................................................................................ 21 3.5. Test Specification.......................................................................................................... 21 3.6. Test Result.................................................................................................................... 22 4. Radiated Emission ..................................................................................................... 31 4.1. Test Equipment............................................................................................................. 31 4.2. Test Setup .................................................................................................................... 31 4.3. Limits ............................................................................................................................ 32 4.4. Test Procedure ............................................................................................................. 32 4.5. Test Specification.......................................................................................................... 32 4.6. Test Result.................................................................................................................... 33 4.7. Test Photo .................................................................................................................... 37 5. RF Conducted Emission ............................................................................................ 39 5.1. Test Equipment............................................................................................................. 39 5.2. Test Setup .................................................................................................................... 39 5.3. Limits ............................…

Text truncated - open the document above for the full version.

Report No： 081090R-RFUSP06V01-1 Page: 20 of 99 2.7. Test Photo Test Mode ： Mode 1: Transmit Description： Front View of Conducted Emission Test Setup Test Mode ： Mode 1: Transmit Description： Back View of Conducted Emission Test Setup Report No： 081090R-RFUSP06V01-1 Page: 37 of 99 4.7. Test Photo Test Mode ： Mode 1: Transmit Description： Front View of Radiated Emission Test Setup (Bilog) Test Mode ： Mode 1: Transmit Description： Back View of Radiated Emission Test Setup (Bilog) Report No： 081090R-RFUSP06V01-1 Page: 38 of 99 Test Mode ： Mode 1: Transmit Description： Front View of Radiated Emission Test Setup (Horn)