N9644000104Electronic Ballast

44000104 User Manual 44000104 is an electronic ballast to be used with 20” UV lamp. - Input voltage – 120V 60Hz - Input power – 27W - Safety – UL and cUL approved per UL 935 and UL 1995, File E233711 - Suitable lamps- 1 pc 20” UV HO lamp This equipment has been tested and found to comply with the limits for a Consumer device, pursuant to Part 18 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment generates, uses, and can radiate frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If interference problems do occur, please do as following suggestions: (1) Turn off this equipment only. If the interference is still there, please check other system; If the interference disappears, go to step 2; (2) Make sure this equipment is grounded and the outlet has ground (green) wire; (3) If the television or radio is interfered, please relocate the equipment away from the television or radio; (4) If other equipments share the same outlet with this equipment and get interfered, please place the AC power connection of this equipment on a different outlet; (5) If the interference is still there, this equipment may be defective. Please contact the manufacturer for replacement. Change or modifications to this product without the express approval of Sunpark Electronics could result in non-FCC compliance, and void the user's authority to operate this equipment.

44000104 Block Diagram 120V 60Hz Filter Rectifier Inverter 48kHz Lamp 60Hz 300V DC 48kHz

SUNPARK ELECTRONICS CORP.FCC ID: N9644000104 Report # DOCUMENT1Page 3 of 16FCC Part 18 Report APPENDIX C - EUT PHOTOGRAPHS EUT – Front View, Chassis Cover Off

APPENDIX A - FCC PRODUCT LABELING AND WARNING STATEMENT Proposed FCC Label Format FCC ID: N9644000104 Specifications: Text is black or white in color and is left justified. Labels are silk-screened and shall be “permanently affixed” at a conspicuous location on the EUT. Proposed Label Location on EUT Front View of EUT Proposed FCC Label Location FCC Warning Statement This device complies with Part 18 of FCC rules. Information on the following matters shall be provided to the user in the instruction manual or on the packaging if an instruction manual is not provided for any type of any ISM equipment: a. The interference potential of the device or system b. Maintenance of the system c. Simple measures that can be taken by the user to correct interference.

SUNPARK ELECTRONICS CORP.FCC ID: N9644000104 Report # DOCUMENT1Page 4 of 16FCC Part 18 Report EUT – Component View EUT – Solder View

7/10/2003 Model No: 44000104 DESCRIPTIONDESIGNATIONU/MQTY PCB, CEM-1, 94V-0EA1 RES, 240K, 1/4WR1A, 1B, 2A, 2BEA4 RES, 30, 1/4WR3, 4EA2 RES, 0.5, 1/2WR6, 7EA2 RES, 470, 1/4WR8EA1 CAP, 0.047uF/400VC1, 7, 9EA3 CAP, 33uF/200VC2A, C2BEA2 CAP, 3300pF/3KVC3EA1 CAP, 0.0033uF/630VC4EA1 CAP, 0.047uF/50VC6, 12EA2 CAP, 0.0027uF/630VC8EA1 DIO, 1A/1000VD1, D2, D3, D4EA4 DIO, LEDD11, 12EA2 Insulating Tubing, Fiberglass, 94-V0EA4 DIO, 1A, 1000VD5, 6, 7EA3 DIO, DIAC, 28-36VD8EA1 DIO, 1A, 40VD9, D10EA2 FUSE, 1A/125VF1EA1 CONNECTOR, POWER, H7730R-09CON1EA1 CONNECTOR, LAMP SOCKETCON2EA1 CHOKE, 1.2mHL1EA1 CHOKE, 200uHL2EA1 CHOKE, 11mHL3EA1 XFRM, TOROIDT1EA1 X'STR, 4A/400VQ1, Q2EA2

1234 A B C D 4321 D C B A Title NumberRevisionSize Letter Date:30-Oct-2002Sheet of File:C:\Richard Zhang\..\carrier 3x3 connector.SchDrawn By: D8 F1 C9 L3 C1 L2 C3 D1 D2D4 R2A R1A C6 R2B R1B C4 D7 T1B R3 C10 Q1 R6 R7 Q2 C11 R4 T1C T1A D5 D6 L1 C8A C7 C2A C2B CARRIER UV BALLAST 1/1 D3 CON1 CON2 C12 R8 D11D12 SOCKETASOCKETB D9 D10 X X X X X X X X X

Note: The test report is specially limited to the use of the above client company and the product model. It may not be duplicated without prior written consent of Bay Area Compliance Laboratory Corporation. This report must not be used by the client to claim product endorsement by NVLAP or any agency of the U.S. Government. FCC PART 18 MEASUREMENT AND TEST REPORT For SUNPARK ELECTRONICS CORP. 1815 WEST 205 TH ST., SUITE 104 TORRANCE, CA90501 FCC ID: N9644000104 2003-08-01 This Report Concerns: Original Report Equipment Type: Electronic Ballast Test Engineer:Peter Liu Report Number:R0307153 Test Date:2003-07-23 Reviewed By:Hans Mellberg Prepared By:Bay Area Compliance Laboratory Corporation 230 Commercial Street Sunnyvale, CA 94085 Tel: (408) 732-9162 Fax: (408) 732-9164 SUNPARK ELECTRONICS CORP.FCC ID: N9644000104 Report # R0307153RPTPage 2 of 10FCC Part 18 Report TABLE OF CONTENTS 1 - GENERAL INFORMATION.................................................................................................................................................3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT).........................................................................................3 1.2 OBJECTIVE................................................................................................................................................................................3 1.3 RELATED SUBMITTAL(S)/GRANT(S)......................................................................................................................................3 1.4 TEST METHODOLOGY.............................................................................................................................................................3 1.5 TEST FACILITY.........................................................................................................................................................................3 1.6 TEST EQUIPMENT LIST AND DETAILS...................................................................................................................................4 1.7 EQUIPMENT UNDER TEST (EUT)...........................................................................................................................................4 2 - SYSTEM TEST CONFIGURATION..................................................................................................................................5 2.1 JUSTIFICATION.........................................................................................................................................................................5 2.2 SCHEMATICS / BLOCK DIAGRAM..........................................................................................................................................5 2.3 EQUIPMENT MODIFICATIONS.................................................................................................................................................5 2.4 CONFIGURATION OF TEST SYSTEM.......................................................................................................................................6 2.5 TEST SETUP BLOCK DIAGRAM..............................................................................................................................................6 3 - CONDUCTED EMISSIONS TEST DATA........................................................................................................................7 3.1 MEASUREMENT UNCERTAINTY.............................................................................................................................................7 3.2 EUT SETUP...............................................................................................................................................................................7 3.3 SPECTRUM ANALYZER SETUP...............................................................................................................................................7 3.4 TEST PROCEDURE....................................................................................................................................................................7 3.5 SUMMARY OF TEST RESULTS.................................................................................................................................................8 3.6 CONDUCTED EMISSIONS TEST DATA....................................................................................................................................8 3.7 PLOT(S) OF CONDUCTED EMISSIONS TEST DATA...............................................................................................................8 SUNPARK ELECTRONICS CORP.FCC ID: N9644000104 Report # R0307153RPTPage 3 of 10FCC Part 18 Report 1 - GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) The SUNPARK ELECTRONICS CORP.’s 44000104 or the “EUT” as referred to in this report is an electronic ballast. The EUT measures 4.0” L x 3.0” W x 1.9”H. Note: The test data was only good for the test sample. It may have deviation for other test sample. 1.2 Objective The following test report is prepared on behalf of SUNPARK ELECTRONICS CORP. in accordance with Part 2, Subpart J, and Part 18, Subparts A, B, and C of the Federal Communication Commissions rules and regulations. The objective of the manufacturer is to demonstrate compliance with FCC Part 18 limit requirements for Industrial, Scientific, and Medical Equipment. 1.3 Related Submittal(s)/Grant(s) No Related Submittals. 1.4 Test Methodology All measurements contained in this report were conducted in accordance with MP-5, FCC Methods of Measurements of Radio Noise Emissions from Industrial, Scientific, and Medical Equipment. All radiated and conducted emission measurements were performed at Bay Area Compliance Laboratory Corp. (BACL). The radiated testing was performed at an antenna-to-EUT distance of 3 Meters. 1.5 Test Facility The Open Area Test site used by Bay Area Com…

Text truncated - open the document above for the full version.

SUNPARK ELECTRONICS CORP.FCC ID: N9644000104 Report # DOCUMENT1Page 2 of 16FCC Part 18 Report APPENDIX B - TEST SETUP PHOTOGRAPHS Conducted Emission