NBFAS-8510-BHandheld Bar Code Scanner (Cradle)

User’s Manual Argox Handheld Bar Code Scanner Model No.: 1 USING AS-8510/8512 RADIO CRADLE The AS-8510/8512 radio cradle paired with one AS-8510/8512 scanner, builds a Cordless Reading System for the collection, decoding and transmission of barcoded data. It can be connected to a Host PC through an RS232, Keyboard wedge or USB cable and is suited for a single-cradle layout. The LEDs signal of the AS-8510/8512 radio cradle status, as described in the following: BATTERY: - Green LED blinking: the batter charge is in progress. - Green LED On: the battery is completely charged. TRANSMISSION: - Green LED On: the radio cradle is powered. - Orange LED blinking: the radio cradle receives data and commands from the Host or the scanner. CONNECTING AND DISCONNECTING THE RADIO CARDLE INTERFACE CABLE The radio cradle can be connected to a Host by means of an RS232, Keyboard wedge or USB cable which must be simply plugged into the Host connector, placed on the base of the cradle. In addition the cradle must be connected to an external power supply. To disconnect the cable, insert a paper clip or other small similar object into the hole at the back of the cradle. Push down on the clip while unplugging the cradle. 2 Default setting For each barcode shown as below: Read Enable Code Type 8510 8512 Checksum Verification Enable Checksum Transmission Enable Code ID UPC-A A UPC-E E EAN-13 F EAN-8 FF Code-39 * Interleaved 2 of 5 i Industrial 2 of 5 - - i Matrix 2 of 5 B Codabar % Code-128 # Code-93 & Code-11 One digit O MSI/Plessey @ UK/Plessey @ Telepen S Standard 2 of 5 i China Post t Italian Pharmacode. p Code-16K - - PDF417 - - EAN UCC Composite - - RC 3 Depth-head 35 mm Weight Less than 250g (with a battery) ArgoScan 8510/8512 Specification Model 8510 / 8512 Operational Light Source 635 nm Visible Red LED Optical System 2048 pixel CCD (Charge-coupled device) Depth of Scan Field Up to 600mm (CODE 39, PSC=90%, 20mils) Scanning Width 160mm Scan Speed 400 scans/sec Resolution 0.1mm(4mils) Code39,PCS=90% Print Contrast 25% or more Scanning Angle Front: 60° Rear: 60° Yaw: 70° Decode Capability Autodiscriminates all standard barcodes; Other symbologies can be ordered optionally (2D symbologies for 8512 only) Beeper Operation 7 tones or no beep Indicator Green & Red led Mechanical Length 164 mm Width-handle 30 mm Width-head 78 mm Depth-handle 56 mm 4 Case material ABS (over molded at contact pointed) Cushion material Double injection Cradle interface RS232, Keyboard wedge, USB Electrical Input Voltage (Cradle) 5 VDC ± 10% VDC Power - Operating (Cradle) 5 VDC Power – Standby (Cradle) 5 VDC Current – Operating (Cradle) 132 mA Current – Standby (Cradle) 132 mA Charge Current (Cradle) 340 mA Input Voltage (Scanner) 3.4V ~ 4.2V Power - Operating (Scanner) 3.2V ~ 4.0V Power – Standby (Scanner) 3.4V ~ 4.2V Current – Operating (Scanner) 225 mA Current – Standby (Scanner) 13 mA Light Level Up to 70000 Lux Shock 1.5m drop onto concrete Contaminants Seals to resist airborne particulate contaminants (IP42) 5 Ventilation None required Programming Programming method Manual (Reading special barcode) DOS command through RS-232, Windows configuration program Program upgrade Enabled by built-in flash memory Programmable characteristics Code type selection, check digit selection Decoding option Decoding option Transmitted character delay, Header selection, trailer selection, message suffix, good read beep tone and volume, scanner trigger selection Keyboard emulation type (intermessage delay, keyboard type and keyboard language) Serial interface type (ACK/NAK, Xon/Xoff, RTS/CTS, good read LED control, start/stop bits) 6 Programming the AS-8510 / 8512 To program the 8510 or 8512, you must scan a series of programming barcode in the correct order. Fold out the back cover of this manual. You will see a table of alphanumeric barcodes, which are used to program the various options presented. To program each option, you must: 1. Scan the Program barcode on the parameter setting part. 2. Enter the option mode by scanning the Option Bar Code (also on the Parameter setting part). 3. To the right of the option barcode, the necessary alphanumeric inputs are listed. Scan these alphanumeric entries from the back fold out page. To confirm above steps, you must scan the Finish barcode on the back fold out page. 4. Once you have finished programming. Scan the Exit barcode, listed on the lower right hand corner of each parameter setting part. 7 Option Bar Code Option Alphanumeric Entry Interface selection Keyboard Wedge RS-232 Wand emulation USB Keyboard/RS-232 Auto detection Reserved 00* 01 02 03 04 05 Program Exit Program Barcode Option Barcode Exit Barcode Back Fold Out Finish barcode 8 Exit Interface Selection This decoder built-in scanner comes in one model and supports interfaces such as keyboard wedge, RS232 serial wedge, wand emulation, and the latest USB interface. In most of the cases, simply selecting an appropriate cable with a device code will work for a specific interface. Interface selection: You can change factory interface default for other type interface. By plugging different cables, setting right interface, then the scanner will be changed to another interface. However, you must make sure which cable you need. Keyboard/RS232/UBS Auto detection: By setting this function, it will automatically select the Keyboard wedge or RS-232 or UBS interface for user. Option Bar Code Option Alphanumeric Entry Interface selection Keyboard Wedge RS-232 Wand emulation USB Keyboard /RS232/USB Auto detection Reserved 00 01 02 (8110/8210/8150) 03 04* 05 Program Note:*-Default 9 Exit Keyboard wedge As a keyboard interface, the scanner supports most of the popular PCs and IBM terminals. The installation of the wedge is a fairly simple process without any changes of software or hardware. Keyboard Type: Select keyboard type connector of your host computer. Scanner must be selected to the appropriate host interface cable converter. Option Bar Code Option …

Text truncated - open the document above for the full version.

1 Helen Zhao Subject:FW: ??: FW: Argox Information Co., Ltd., FCC ID: NBFAS-8510-B, Assessment NO.: AN05T4619, Notice#1 AS-8510 cradle UserMan revised... From: [email protected] Sent: Friday, March 11, 2005 12:18 AM To: Helen Zhao Cc: Application (CCS TW) (E-mail) Subject: ??: FW: Argox Information Co., Ltd., FCC ID: NBFAS-8510-B, Assessment NO.: AN05T4619, Notice# 1 Dear Helen, Please refer to below for our reply. Best Regards, Ting Question #1: The test report includes MPE calculation, the device is classified as mobile device. Please add required RF exposure statement such as 20cm separation distance (for cradle) into the manual. Ans #1: The statement for cradle has been added and please refer to the attached for revised user manual. Question #2: The manual does not contain any information as how to install the software to enable bluetooth function and how to setup communication link between the scanner and the cradle. Please provide basic application information. Ans #2: Please refer to the attached for revised user manual. Question #3: Pleaes confirm the EUT description for this filing is "Handheld Bar Code Scanner", though it is part of Handheld Bar Code Scanner system, it is just a cradle, no scanning function at all. Please confirm if it is OK to use "Handheld Bar Code Scanner system (cradle)". Ans #3: After confirm our client, they would like use original EUT description "Handheld Bar Code Scanner" because normally two devices are considered as a set. (See attached file: AS-8510 cradle UserMan revised 0311.pdf) The items indicated above must be submitted before processing can continue on the above referenced application. Failure to provide the requested information within 30 days of the original e-mail date may result in application dismissal and forfeiture of the filing fee. Also, please note that partial responses increase processing time and should not be submitted. Any questions about the content of this correspondence should be directed to the e-mail address listed below the name of the sender. 2 ________________________________________________________________________ This e-mail transmission is confidential and intended solely for being reviewed by the recipient(s) identified above. If you are not an identified recipient, please ensure that this communication remains confidential and promptly return it to the sender. Please contact immediately by phone (Tel: 886-2-2299-9720) for any problem with this transmission, Thank you for your attention.

Compliance Certification Services Inc. Report No: 41109408 Date of Issue: February 03, 2005 Page 1 Total Page: 5 Rev. 00 EXTERNAL PHOTOGRAPHS OF EUT Compliance Certification Services Inc. Report No: 41109408 Date of Issue: February 03, 2005 Page 2 Rev. 00 Compliance Certification Services Inc. Report No: 41109408 Date of Issue: February 03, 2005 Page 3 Rev. 00

Compliance Certification Services Inc. Report No: 41109408 Date of Issue: February 03, 2005 Page 4 Rev. 00 INTERNAL PHOTOGRAPHS OF EUT Compliance Certification Services Inc. Report No: 41109408 Date of Issue: February 03, 2005 Page 5 Rev. 00

Phycomp Product specification High Frequency SMD type antennas for BT/802.11b/g application 2.45 GHz size 5.3 × 2.0 2004 Jul 15 Rev.3 2 www.yageo.com QUICK REFERENCE DATA DESCRIPTION VALUE Centre frequency 2.45 GHz 0 type/01type/02 type/03 type/Default/04 type/05 type Bandwidth ＞100 MHz Gain 4 dBi max. (depends on the special environment) VSWR 2.5 max. (depends on the special environment) Polarization Linear Azimuth beam width Omni-directional Impedance 50 Ω Power dissipation 1 W Operating temperature −55 to +85 °C Terminations NiSn Resistance to soldering heat 260 °C for 10 seconds DESCRIPTION This 2.45 GHz ceramic multilayer antenna has been designed to meet the requirements of the Bluetooth TM(1) and IEEE 802.11b/g wireless communications protocol. It consists of a rectangular block of low-dielectric ceramic material and is fabricated in a water-based non-toxic process. The antenna is capable of providing good connectivity using near 50 Ω microstrip directly onto the PC board. Notes 1. Bluetooth is a trademark owned by Telefonieaktiebolaget L M Ericsson, Sweden. FEATURES • Designed for 2.45 GHz ISM-band • Simplifies antenna circuitry • NiSn lead-free terminations • Suitable for wave and reflow soldering • Supplied in tape on reel. APPLICATIONS • Telecommunications • Computing (PCs, printers, PDAs) • Wireless office data communications including WLAN • Consumer electronics (wireless headphones).

Compliance Certification Services Inc. Report No.: 41109408-RP1-1 FCC ID: NBFAS-8510-B Date of Issue: February 03, 2005 Note: This report shall not be reproduced except in full, without the written approval of Compliance Certification Services Inc. This document may be altered or revised by Compliance Certification Services Inc. personnel only, and shall be noted in the revision section of the document. Page 1 Total Page: 48 Rev. 00 FCC 47 CFR PART 15 SUBPART C TEST REPORT For Handheld Bar Code Scanner Model: AS-8510 Trade Name: Argox Issued to Argox Information Co., Ltd. 7F, NO.126, Lane 235, Pao-Chiao Rd., Hsin Tien, Taipei, Taiwan, R.O.C Issued by Compliance Certification Services Inc. No. 81-1, Lane 210, Bade Rd. 2, Luchu Hsiang, Taoyuan Hsien, (338) Taiwan, R.O.C. TEL: 886-3-324-0332 FAX: 886-3-324-5235 Compliance Certification Services Inc. Report No.: 41109408-RP1-1 FCC ID: NBFAS-8510-B Date of Issue: February 03, 2005 Page 2 Rev. 00 TABLE OF CONTENTS 1. TEST RESULT CERTIFICATION................................................................................................................3 2. EUT DESCRIPTION........................................................................................................................................4 3. TEST METHODOLOGY ................................................................................................................................5 3.1 EUT CONFIGURATION.....................................................................................................................................5 3.2 EUT EXERCISE................................................................................................................................................5 3.3 GENERAL TEST PROCEDURES.........................................................................................................................5 3.4 MODIFICATION..............................................................................................................................................5 3.5 FCC PART 15.205 RESTRICTED BANDS OF OPERATIONS ....................................................................6 3.6 DESCRIPTION OF TEST MODES........................................................................................................................6 4. INSTRUMENT CALIBRATION ....................................................................................................................7 5. FACILITIES AND ACCREDITATIONS ......................................................................................................8 5.1 FACILITIES ...................................................................................................................................................8 5.2 EQUIPMENT ...................................................................................................................................................8 5.3 LABORATORY ACCREDITATIONS AND LISTING...............................................................................................8 5.4 TABLE OF ACCREDITATIONS AND LISTINGS....................................................................................................9 6. SETUP OF EQUIPMENT UNDER TEST ...................................................................................................10 6.1 SETUP CONFIGURATION OF EUT...................................................................................................................10 6.2 SUPPORT EQUIPMENT ..........................................................................................................................10 7. FCC PART 15.247 REQUIREMENTS.........................................................................................................11 7.1 PEAK POWER................................................................................................................................................11 7.2 BAND EDGES MEASUREMENT............................................................................................................12 7.3 PEAK POWER SPECTRAL DENSITY................................................................................................................17 7.4 FREQUENCY SEPARATION ..................................................................................................................20 7.5 NUMBER OF HOPPING FREQUENCY..................................................................................................22 7.6 TIME OF OCCUPANCY (DWELL TIME) ..............................................................................................24 7.7 RADIO FREQUENCY EXPOSURE.....................................................................................................................31 7.8 SPURIOUS EMISSIONS ............................................................................................................................34 7.9 POWERLINE CONDUCTED EMISSIONS...........................................................................................................44 APPENDIX 1 PHOTOGRAPHS OF TEST SETUP ...........................................................................................47 Compliance Certification Services Inc. Report No.: 41109408-RP1-1 FCC ID: NBFAS-8510-B Date of Issue: February 03, 2005 Page 4 Rev. 00 2. EUT DESCRIPTION Product Handheld Bar Code Scanner Trade Name Argox Model Number AS-8510 Model Discrepancy N/A Power Supply Adapter: LISTED / SCP41-50500 I/P: 120V, 60Hz O/P: 5V, 500mA Frequency Range 2402 ~ 2480 MHz Transmit Power -0.81 dBm Modulation Technique FHSS Transmit Data Rate 1Mbps Number of Channels 79 Channels Antenna Specification Chip Antenna / Gain: 4.0 dBi Remark: This submittal(s) (test report) is intended for FCC ID: NBFAS-8510-B filing to comply with Section 15.207, 15.209 and 15.247 of the FCC Part 15, Subpart C Rules. Compliance Certification Services Inc. Report No.: 41109408-RP1-1 FCC ID: NBFAS-8510-B Date of Issue: February 03, 200…

Text truncated - open the document above for the full version.

Compliance Certification Services Inc. Report No.: 41109408-RP1-1 FCC ID: NBFAS-8510-B Date of Issue: February 03, 2005 Page 47 Rev. 00 APPENDIX 1 PHOTOGRAPHS OF TEST SETUP Radiated Emission Set up Photos Compliance Certification Services Inc. Report No.: 41109408-RP1-1 FCC ID: NBFAS-8510-B Date of Issue: February 03, 2005 Page 48 Rev. 00 Conducted Emission Set Up Photos