NC3TRACKER-100Tracker 100

Allied Universal Electronic Monitoring US, Inc. Section 2.911 (d)(7) USA Agent for Service of Process Company name: Allied Universal Electronic Monitoring US, Inc. Address: 1838 Gunn Highway, Odessa, Florida 33556, United States Product Name: Tracker 100 FCC ID: NC3TRACKER-100 Model(s): TRC-1 OO-NA-9-00 2.911(d)(7) USA Designated Agent for Service of Process We, [Allied Universal Electronic Monitoring US, Inc.] designate [Allied Universal Electronic Monitoring US, Inc.] NOTE1 for the purpose of accepting service of process on behalf of the applicant. Applicant consent: We acknowledge our consent to accept service of process in the United States for matters related to the applicable equipment, and at the physical U.S. address and email address of the designated agent and acknowledge our acceptance of our obligation to maintain an agent for service of process in the United States for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. Agent obligation: We acknowledge our obligation to accept service of process in the United States for matters related to the applicable equipment at our physical U.S. address and email address for no less than one year after either the grantee has permanently terminated all marketing and importation of the applicable equipment within the U.S., or the conclusion of any Commission-related administrative or judicial proceeding involving the equipment, whichever is later. USA Agent C ompany name: Allied Universal Electronic Monitoring US, Inc. Address: 1838 Gunn Highway, Odess a, Florida, United States, 33556 FRN: 0034951947 C ontact Name: Daniel Williamson Telephone No: +1 813 749 5454 Email: [email protected] Signature Y � UU---- Title: Electronics/RF Engineer Tech Date: 2024-01-10 Applicant C ompany name: Allied Universal Electronic Monitoring US, Inc. Address: 1838 Gunn Highway, Odessa, Florida, United States, 33556 F RN: 0034951947 Contact Name: Daniel Williamson Telephone No: +1 813 749 5454 Email: [email protected] Signatu � � Ti tle: Elec��F Engineer Tech Date: 2024-01-10 Allied Universal Electronic Monitoring US, Inc. NOTE 1: An applicant located in the United States may designate itself as the agent for service of process. Reference; Federal Register document 2022-28263 published on 02/06/23 https://www.federalregister.gov/documents/2023/02/06/2022-28263/protecting-against-nation al-security-threats-to-the-communications-supply-chain-through-the

Allied Universal Electronic Monitoring US, Inc. Office of Engineering Technology Federal Communications Commission 7 435 Oakland Mills Road Columbia, MD 21046 USA Subject; Request for Confidentiality FCC ID: NC3TRACKER-100 To Whom It May Concern, Date: 2024-01-10 Pursuant to the provisions of the Commission's rules Title 47 Sections §0.457 and §0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. [:8'.]Schematic Diagram [:8'.]Block Diagram [:8'.]Operational Description [:8'.]BOM [:8'.]Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s); [:8'.]External Photos [:8'.]Test Setup Photos [:8'.]lnternal Photos [:8'.]User Manual □For 45 days, pursuant to Public Notice DA 04-1705. OR [:8'.]For 180 days pursuantto KDB 726920 D01. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: � � � Name: Daniel Williamson Title: Electronics/RF Engineer Tech \ (IO/ 1.,p 7--'-{ Date: 1/10/2024

Letter of Authorization Company: Allied Universal Electronic Monitoring US, Inc. Address: 1838 Gunn Highway, Odessa, Florida 33556, United States Product Type: Tracker 100 Model Number(s): TRC-100-NA-9-00 Product Description: Tracker 100 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: Date: 2023-12-25 Name: Daniel Williamson Title: Electronics/RF Engineer Tech Company: Allied Universal Electronic Monitoring US, Inc.

8.0 5.30 QR Code position is in the middle of the surface A 5.76 3.00 1.50 12.50 6.00 12.00 33.50 B All writing should be filled (not hollow!!!) Font : "Century Gothic" FONT: Century Gothic Regular 6 FONT: Centry Gothic Regular 11 FONT: Century Gothic Regular 6 XXXXXXXX= Country Of Origin Optional writing Area "attenti" LOGO font as shown in detail "B" 8.00 5.30 11.30 Ref. VIEW A SCALE 1 : 1 QR CODE 3.23 DETAIL B SCALE 5 : 1 please notice: QR code content : - 1st line : S/N - 2nd line : Top P/N and revison For QR content and S/N format, Refer to Attenti SI-075 Document ! REVISIONS ECOREV.DESCRIPTIONDATEAPPROVED 010246A00Release02/20/2022Andrew Moonin D C B A A B C D 1 2 3 4 5 6 7 8 8 7 6 5 4 3 2 1 DIMENSIONS ARE IN MILLIMETERS THIS DOCUMENT IS COPYRIGHTED PROPERTY OF ATTENTI COMPANY AND MAY NOT BE REPRODUCED WITHOUT ATTENTI WRITTEN PERMISSION OR USED OR DISCLOSED FOR OTHER THAN ATTENTI AUTHORIZED PURPOSES. TOLERANCES (UNLESS OTHERWISE SPECIFIED) 0.5 TO 6 0.1 > 6 TO 30 0.2 > 30 TO 120 0.3 >120 TO 400 0.5 ANGULAR: .5 REVISION ITEM NUMBER (PARTS LIST) INSPECTION DIMENSION CORRESPONDING NOTE SYMBOL KEY: PROJECTION: A00 32001024 PART. NO. INPERPRET PER ASME Y14.5M-1994 SHEET 1 OF 1 WEIGHT (gr): REV DOC. NO. A3 SIZE TITLE: NAMEDATE CHECKED DRAWN SEE NOTES FINISH MATERIAL NG Tracker-100 BOTTOM HOUSING LASER ETCHING NA Andrew Moonin 10/26/2023 SCALE 32001024 2:1 Andrew Moonin10/26/2023 For DFM & Quotation only

SAR Test Report For Applicant Name: Allied Universal Electronic Monitoring US, Inc. Address: 1838 Gunn Highway, Odessa, Florida 33556, United States EUT Name: Tracker 100 Model Number: TRC-100-NA-9-00 Issued By Company Name: BTF Testing Lab (Shenzhen) Co., Ltd. F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Address: Tantou Community, Songgang Street, Bao'an District, Shenzhen, China Report Number: BTF231207R00501 47 CFR Part 2.1093 IEEE1528-2013 IEEE C95.1-2019 Test Standards: KDB 447498 D01 KDB 865664 D01 KDB 865664 D02 KDB 248227 D01 KDB 690783 D01 FCC ID: NC3TRACKER-100 Test Conclusion: Pass Test Date: 2023-12-14 to 2023-12-15 Date of Issue: 2023-12-18 Prepared By: Amenda Zhong / Project Engineer Date: 2023-12-18 Approved By: Ryan.CJ / EMC Manager Date: 2023-12-18 Note: All the test results in this report only related to the testing samples. Which can be duplicated completely for the legal use with approval of applicant; it shall not be reproduced except in full without the written approval of BTF Testing Lab (Shenzhen) Co., Ltd., All the objections should be raised within thirty days from the date of issue. To validate the report, you can contact us. Total or partial reproduction of this document without permission of the Laboratory is not allowed. Page 1 of 54 BTF Testing Lab (Shenzhen) Co., Ltd. F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China Test Report Number: BTF231207R00501 Revision History Version Issue Date Revisions Content R_V0 2023-12-18 Original Note: Once the revision has been made, then previous versions reports are invalid. Total or partial reproduction of this document without permission of the Laboratory is not allowed. Page 2 of 54 BTF Testing Lab (Shenzhen) Co., Ltd. F101, 201 and 301, Building 1, Block 2, Tantou Industrial Park, Tantou Community, Songgang Street, Bao'an District, Shenzhen, China Test Report Number: BTF231207R00501 Table of Contents 1. Introduction ............................................................................................................................................................................................. 4 1.1 Identification of Testing Laboratory ............................................................................................................................................. 4 1.2 Identification of the Responsible Testing Location.................................................................................................................... 4 1.3 Laboratory Condition ..................................................................................................................................................................... 4 1.4 Announcement ............................................................................................................................................................................... 4 2. Product Information ................................................................................................................................................................................ 5 2.1 Application Information .................................................................................................................................................................. 5 2.2 Manufacturer Information .............................................................................................................................................................. 5 2.3 General Description of Equipment under Test (EUT) ............................................................................................................... 5 2.4 Equipment under Test Ancillary Equipment ............................................................................................................................... 5 2.5 Technical Information .................................................................................................................................................................... 5 3. Summary of Test Results ...................................................................................................................................................................... 6 3.1 Test Standards ............................................................................................................................................................................... 6 3.2 Device Category and SAR Limit .................................................................................................................................................. 7 3.3 Test Result Summary .................................................................................................................................................................... 7 3.4 Test Uncertainty ............................................................................................................................................................................. 8 4. Measurement System ......................................................................................................................................................................... 10 4.1 Specific Absorption Rate (SAR) Definition .............................................................................................................................. 10 4.2 MVG SAR System ...................................................................................................................................................................... 10 5. System Verification ............................................................................................................................................................................. 14 5.1 Purpose of System Check ......................................................................................................................................................... 14 5.2 System…

Text truncated - open the document above for the full version.

SPE-12-8-079/F/WY Page 1 of 15 SPECIFICATION Part Number : Product Name : Features : ILA.01 Low Profile and High Efficiency 915 MHz ISM Band Loop Antenna Small size antenna, low profile, and high efficiency 915 MHz ISM Band 1.5 dBi Peak Gain 10 x 3.2 x 0.5 mm size SMT Compatible RoHS Compliant SPE-12-8-079/F/WY Page 2 of 15 1.Introduction The ILA.01 is a 915 MHz ISM band antenna with excellent efficiency, 60% at the center frequency and 45% at the band edges. This antenna works the best when placed at the center of the board edge. The antenna, at 10 x 3.2 x 0.5 mm, is low profile and would be suitable for devices with space constraints. The ILA.01 is delivered on tape and reel and now allows M2M customers to use an omni-directional SMT antenna. The omni-directional radiation characteristics allow for excellent performance regardless of device orientation. This is especially useful for devices that are not fixed in one particular spot during use. When there is little PCB space available for antenna placement, but high performance is required, the ILA.01 is the ideal choice. The ILA.01 Loop antenna can be used in automated meter reading (AMR), radio frequency identification (RFID), remote monitoring, healthcare, sensing, and other 915 MHz applications. SPE-12-8-079/F/WY Page 3 of 15 2.Specification ELECTRICAL Antenna ILA.01 Standard 915 MHz ISM Operation Frequency (MHz) 902-928 MHz Polarization Linear Impedance 50 Ohms Max VSWR (dBi) 6:1 Max Return Loss (dB) -2.8 dB Peak Gain 1.5 dBi Efficiency (%) 50 typ. Average Gain (dB) -5 Radiation Properties Omni-directional Max Input Power 5 W * The ILA.01 antenna performance was measured with 80x40 mm ground plane. MECHANICAL Dimensions (mm) 10x3.2x0.5 Required Space (mm) 11x10.4 Material Ceramic EVB Connector SMA(F) ENVIRONMENTAL Operation Temperature -40°C to 85°C Storage Temperature -40°C to 105°C Relative Humidity 40% to 95% RoHS Compliant Yes SPE-12-8-079/F/WY Page 4 of 15 3.Test Setup Figure 1. Impedance measurements (left hand) and peak gain, average gain, efficiency, and radiation pattern measurements (right hand). X Z Y SPE-12-8-079/F/WY Page 5 of 15 4.Antenna Parameters 4.1. Return Loss Figure 2. Return loss of 915MHz ISM Band Antenna ILA.01 4.2. VSWR Figure 3. VSWR of 915 MHz ISM Band Antenna ILA.01 SPE-12-8-079/F/WY Page 6 of 15 4.3. Efficiency Figure 4. Efficiency of 915 MHz ISM Band Antenna ILA.01 4.4. Peak Gain Figure 5. Peak Gain of 915 MHz ISM Band Antenna ILA.01 SPE-12-8-079/F/WY Page 7 of 15 4.5. Average Gain Figure 6. Average Gain of 915 MHz ISM Band Antenna ILA.01 4.6. Radiation Pattern Figure 7. Radiation Pattern at 915 MHz of the ILA.01 Antenna. SPE-12-8-079/F/WY Page 8 of 15 5.Layout Guide 5.1 Solder Land pattern Land pattern for soldering is as shown below. A matching circuit similar to the one shown in section 5.2 is also required. Figure 8. Foot Print Drawing of the ILA.01 Antenna SPE-12-8-079/F/WY Page 9 of 15 5.2 Solder Land Pattern This antenna includes a fine tuning element (as shown in the land patterns above) that can be used to slightly shift antenna resonance. 5.3 Matching Circuit Like all antennas, surrounding components, enclosures, and changes to the GND plane dimensions can alter performance. A pi-matching network like the one shown below is required in case adjustments need to be made. The antenna EVB has a similar matching network. The components on the EVB are a good starting point for a new design, but will need to be adjusted upon integration for best performance. The zero ohm resistor is needed for the ability to solder down a coax pigtail to make measurements with a vector network analyzer. Figure 9. Matching Circuits Block Diagram. SPE-12-8-079/F/WY Page 10 of 15 6.Drawings (Unit: mm) Antenna Main Body Antenna with EVB SPE-12-8-079/F/WY Page 11 of 15 Figure 10. Drawing of the ILA.01 Antenna SPE-12-8-079/F/WY Page 12 of 15 7.Recommended Reflow The ILA01 Loop Antenna can be assembled following either Sn-Pb or Pb-Free assembly processes. The recommended soldering temperatures are as follows: Figure 11. Reflow Temperature Recommendation SPE-12-8-079/F/WY Page 13 of 15 8.Packaging The ILA.01 antennas are delivered in tape and reel with EIA 481-B polystyrene with 6000 pieces per reel. SPE-12-8-079/F/WY Page 14 of 15 SPE-12-8-079/F/WY Page 15 of 15 Taoglas makes no warranties based on the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Taoglas reserves all rights to this document and the information contained herein. Reproduction, use or disclosure to third parties without express permission is strictly prohibited. Copyright © Taoglas Ltd.

APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 1 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC TITLE 2.4GHZ MID SMT ANTENNA TABLE OF CONTENTS 1.0 SCOPE 2.0 PRODUCT DESCRIPTION 3.0 APPLICABLE DOCUMENTS 4.0 ANTENNA PERFORMANCE 5.0 RECOMMENDED REFLOW CONDITION 6.0 MATCHING NETWORK DESRICPTION 7.0 RF PERFORMANCE AS A FUNCTION OF IMPLEMENTATION APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 2 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC 2.4GHZ MID SMT ANTENNA 1.0 SCOPE This specification describes the antenna application and recommended PCB layout for the Molex 2.4GHz SMD Antenna. The information in this document is for reference and benchmark purposes only. The user is responsible for validating antenna RF performance based on users own PCB and matching circuits. All measurements are done of the antenna mounted on the recommended PCB with VNA Agilent 5071C and OTA chamber. Antenna illustrations in this document are generic representations. They are not intended to be an image of any antenna listed in the scope. 2.0 PRODUCT DESCRIPTION 2.1 PRODUCT NAME AND SERIES NUMBER (S) Product name: 2.4GHz MID SMT Antenna Series Number: 479480001 2.2 DESCRIPTION This is a high-performance antenna implemented using SMD option to meet the customer needs. It has low profile as the size of this antenna. It is designed to cover the frequency 2.4GHz-2.5GHz. 2.3 PRODUCT STRUCTURE INFORMATION Please refer to PS-479480001 for full information. FIGURE 2.3 DIMENSION OF THE 2.4GHZ SMD ANTENNA APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 3 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC 3.0 APPLICABLE DOCUMENTS DOCUMENT NUMBER DESCRIPTION Sale Drawing (SD) SD-479480001 Mechanical Dimension of the product Product Specification (PS) PS-479480001 Product Specification Packing Drawing (PK) PK-479480001 Product packaging specifications 4.0 ANTENNA PERFORMANCE 4.1 RF TEST CONDITIONS The reference design is based on a recommended double side PCB size of 100 mm*40 mm*0.8 mm. There are one feeding pad and three fixing pads.(PCB molex p/n:479489001) FIGURE4.1.1 REFERENCE ANTENNA LOCATION APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 4 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC FIGURE4.1.2 ANTENNA IN FREE SPACE WITH VNA AGILENT E5071C FIGURE4.1.3 ANTENNA IN FREE SPACE WITH OTA CHAMBER DUT DUT APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 5 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC 4.2 ANTENNA PERFORMANCE DESCRIPTION EQUIPMENT REQUIREMENT Frequency Range VNA E5071C 2.4~2.5GHz Return Loss VNA E5071C < -6 dB Peak Gain (Max) OTA Chamber 3.7dBi Average Total Efficiency OTA Chamber >70% Polarization OTA Chamber Linear Input Impedance VNA E5071C 50 Ohms Note that the above antenna performance is measured with just the antenna mounted on a recommended PCB to similar a free-space condition. When implement into the system, the frequency resonant might be off-tune due to the loading of surrounding components especially metal plane. This off-tune can be compensated through matching. Although module manufacturers specify a peak gain limit, it is based on free-space conditions. The peak gain will be degraded by 1 to 2dBi in the actual implementation as the radiation pattern will change due to the surround components. As such, during selection of antenna, you can select one with high peak gain to compensate for the loss. Molex can offer assistant to choose the best location and best tuning in-order to meet this peak gain requirement. APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 6 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC 4.3 RETURN LOSS PLOT All measurements in this document are done of the antenna mounted on the recommended PCB. FIGURE 4.3 RETURN LOSS OF ANTENNA IN FREE SPACE 4.4 EFFICIENCY PLOT All measurements in this document are done of the antenna mounted on the recommended PCB. FIGURE 4.4 EFFICIENCY OF ANTENNA IN FREE SPACE APPLICATION SPECIFICATION REVISION: ECR/ECN INFORMATION: TITLE: 2.4GHz MID SMT Antenna Application Specification SHEET No. F EC No: 637286 7 of 16 DATE: 2020/05/11 DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY: AS-479480001 Liu Hai 2020/05/11 Cheng Kang 2020/05/11 Andy Zhang 2020/05/11 TEMPLATE FILENAME: APPLICATION_SPEC[SIZE_A](V.1).DOC 4.5 RADIATION PATTERN All measurements in this document are done of the antenna mounted on the recommended PCB. FIGURE 4.5.1 2D RADIATION PATTERN OF ANTENNA AT 2.45GHZ IN FREE SPACE APPLICATION SPECIFICATION …

Text truncated - open the document above for the full version.

Report No.: GTS2023110098F04 Page 1 of 7 AppendixA: DTS Bandwidth Test Result Test Mode Antenna Frequency[MHz] DTS BW [MHz] Limit[MHz] Verdict TX Ant1 915 0.6702 0.5 PASS Test Graphs TX-Ant1-915 Report No.: GTS2023110098F04 Page 2 of 7 AppendixB: Occupied Channel Bandwidth Test Result Test Mode Antenna Frequency[MHz] OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict TX Ant1 915 0.58280 914.7175 915.3003 --- --- Test Graphs TX-Ant1-915 Report No.: GTS2023110098F04 Page 3 of 7 AppendixC: Maximum conducted output power Test Result Peak Test Mode Antenna Frequency[MHz] Conducted Peak Powert[dBm] Conducted Limit[dBm] Verdict TX Ant1 915 7.35 ≤30 PASS Test Graphs Peak TX-Ant1-915 Report No.: GTS2023110098F04 Page 4 of 7 AppendixD: Maximum power spectral density Test Result Test Mode Antenna Frequency[MHz] Result[dBm/3kHz] Limit[dBm/3kHz] Verdict TX Ant1 915 4.17 ≤8 PASS Test Graphs TX-Ant1-915 Report No.: GTS2023110098F04 Page 5 of 7 AppendixE:Band edge measurements Test Result Test Mode Antenna ChName Frequency[MHz] RefLevel[dBm] Result[dBm] Limit[dBm] Verdict TX Ant1 Low 915 7.22 -45.98 ≤-12.78 PASS TX Ant1 High 915 7.21 -45.03 ≤-12.79 PASS Test Graphs TX-Ant1-915 TX-Ant1-915 Report No.: GTS2023110098F04 Page 6 of 7 AppendixF:Conducted Spurious Emission Test Result Test Mode Antenna Frequency[MHz] FreqRange [MHz] RefLevel [dBm] Result[dBm] Limit[dBm] Verdict TX Ant1 915 0~Reference 7.43 7.43 --- PASS TX Ant1 915 30~1000 7.43 -63.85 ≤-12.57 PASS TX Ant1 915 1000~13000 7.43 -57.12 ≤-12.57 PASS Test Graphs TX-Ant1-915-0~Reference TX-Ant1-915-30~1000 / TX-Ant1-915-1000~13000 / Report No.: GTS2023110098F04 Page 7 of 7 AppendixG: Duty Cycle Test Result Test Mode Antenna Frequency[MHz] ON Time [ms] Period [ms] Duty Cycle [%] Duty Cycle Factor[dB] TX Ant1 915 17.90 19.30 92.75 0.33 Test Graphs NTNV-TX-Ant1-915 ------End------

Report No.: GTS2023110098F01 Page 1 of 17 AppendixA: DTS Bandwidth Test Result Test Mode Antenna Frequency[MHz] Rate DTS BW [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict 11B Ant1 2412 1Mbps 9.080 2407.440 2416.520 0.5 PASS 11B Ant1 2437 1Mbps 8.720 2432.480 2441.200 0.5 PASS 11B Ant1 2462 1Mbps 8.360 2457.520 2465.880 0.5 PASS 11G Ant1 2412 6Mbps 15.120 2404.440 2419.560 0.5 PASS 11G Ant1 2437 6Mbps 16.040 2428.840 2444.880 0.5 PASS 11G Ant1 2462 6Mbps 15.080 2454.440 2469.520 0.5 PASS 11N20SISO Ant1 2412 MCS0 15.320 2404.480 2419.800 0.5 PASS 11N20SISO Ant1 2437 MCS0 15.440 2429.120 2444.560 0.5 PASS 11N20SISO Ant1 2462 MCS0 15.080 2454.480 2469.560 0.5 PASS Test Graphs 11B-Ant1-2412 11B-Ant1-2437 11B-Ant1-2462 11G-Ant1-2412 Report No.: GTS2023110098F01 Page 2 of 17 11G-Ant1-2437 11G-Ant1-2462 11N20SISO-Ant1-2412 11N20SISO-Ant1-2437 / 11N20SISO-Ant1-2462 / Report No.: GTS2023110098F01 Page 3 of 17 AppendixB: Occupied Channel Bandwidth Test Result Test Mode Antenna Channel Frequency[MHz] Rate OCB [MHz] FL[MHz] FH[MHz] Limit[MHz] Verdict 11B Ant1 2412 1Mbps 13.972 2405.0573 2419.0293 --- --- 11B Ant1 2437 1Mbps 13.986 2429.9205 2443.9065 --- --- 11B Ant1 2462 1Mbps 13.697 2455.0648 2468.7618 --- --- 11G Ant1 2412 6Mbps 16.607 2403.7004 2420.3074 --- --- 11G Ant1 2437 6Mbps 16.598 2428.6579 2445.2559 --- --- 11G Ant1 2462 6Mbps 16.493 2453.7239 2470.2169 --- --- 11N20SISO Ant1 2412 MCS0 17.742 2403.1297 2420.8717 --- --- 11N20SISO Ant1 2437 MCS0 17.773 2428.0864 2445.8594 --- --- 11N20SISO Ant1 2462 MCS0 17.547 2453.1808 2470.7278 --- --- Test Graphs 11B-Ant1-2412 11B-Ant1-2437 11B-Ant1-2462 11G-Ant1-2412 Report No.: GTS2023110098F01 Page 4 of 17 11G-Ant1-2437 11G-Ant1-2462 11N20SISO-Ant1-2412 11N20SISO-Ant1-2437 / 11N20SISO-Ant1-2462 / Report No.: GTS2023110098F01 Page 5 of 17 AppendixC: Maximum conducted output power Test Result Peak Test Mode Antenna Frequency [MHz] Rate Peak Power[dBm] Conducted Limit[dBm] Verdict 11B Ant1 2412 1Mbps 18.99 ≤30.00 PASS 11B Ant1 2437 1Mbps 18.92 ≤30.00 PASS 11B Ant1 2462 1Mbps 19.42 ≤30.00 PASS 11G Ant1 2412 6Mbps 17.72 ≤30.00 PASS 11G Ant1 2437 6Mbps 18.03 ≤30.00 PASS 11G Ant1 2462 6Mbps 18.23 ≤30.00 PASS 11N20SISO Ant1 2412 MCS0 16.86 ≤30.00 PASS 11N20SISO Ant1 2437 MCS0 16.72 ≤30.00 PASS 11N20SISO Ant1 2462 MCS0 17.05 ≤30.00 PASS Report No.: GTS2023110098F01 Page 6 of 17 AppendixD: Maximum power spectral density Test Result Test Mode Antenna Frequency[MHz] Rate Result[dBm/3kHz] Limit[dBm/3kHz] Verdict 11B Ant1 2412 1Mbps -9.1 ≤8.00 PASS 11B Ant1 2437 1Mbps -8.7 ≤8.00 PASS 11B Ant1 2462 1Mbps -8.15 ≤8.00 PASS 11G Ant1 2412 6Mbps -13.8 ≤8.00 PASS 11G Ant1 2437 6Mbps -14.11 ≤8.00 PASS 11G Ant1 2462 6Mbps -13.49 ≤8.00 PASS 11N20SISO Ant1 2412 MCS0 -14.19 ≤8.00 PASS 11N20SISO Ant1 2437 MCS0 -14.1 ≤8.00 PASS 11N20SISO Ant1 2462 MCS0 -13.29 ≤8.00 PASS Test Graphs 11B-Ant1-2412 11B-Ant1-2437 11B-Ant1-2462 11G-Ant1-2412 Report No.: GTS2023110098F01 Page 7 of 17 11G-Ant1-2437 11G-Ant1-2462 11N20SISO-Ant1-2412 11N20SISO-Ant1-2437 / 11N20SISO-Ant1-2462 / Report No.: GTS2023110098F01 Page 8 of 17 AppendixE:Band edge measurements Test Result Test Mode Antenna ChName Frequency[MHz] Rate RefLevel[dBm] Result[dBm] Limit[dBm] Verdict 11B Ant1 Low 2412 1Mbps 4.52 -40.46 ≤-15.48 PASS 11B Ant1 High 2462 1Mbps 5.85 -49.14 ≤-14.16 PASS 11G Ant1 Low 2412 6Mbps 0.05 -36.55 ≤-19.95 PASS 11G Ant1 High 2462 6Mbps 0.42 -49.69 ≤-19.58 PASS 11N20SISO Ant1 Low 2412 MCS0 -0.45 -33.4 ≤-20.45 PASS 11N20SISO Ant1 High 2462 MCS0 -1.00 -48.72 ≤-21 PASS Test Graphs 11B-Ant1-2412 11B-Ant1-2462 11G-Ant1-2412 11G-Ant1-2462 Report No.: GTS2023110098F01 Page 9 of 17 11N20SISO-Ant1-2412 11N20SISO-Ant1-2462 Report No.: GTS2023110098F01 Page 10 of 17 AppendixF:Conducted Spurious Emission Test Result Test Mode Antenna Frequency[MHz] Rate FreqRange [Mhz] RefLevel [dBm] Result [dBm] Limit [dBm] Verdict 11B Ant1 2412 1Mbps 0~Reference 4.79 4.79 --- PASS 11B Ant1 2412 1Mbps 30~1000 4.79 -62.12 ≤-15.21 PASS 11B Ant1 2412 1Mbps 1000~26500 4.79 -49.77 ≤-15.21 PASS 11B Ant1 2437 1Mbps 0~Reference 5.21 5.21 --- PASS 11B Ant1 2437 1Mbps 30~1000 5.21 -61.58 ≤-14.79 PASS 11B Ant1 2437 1Mbps 1000~26500 5.21 -47.12 ≤-14.79 PASS 11B Ant1 2462 1Mbps 0~Reference 5.77 5.77 --- PASS 11B Ant1 2462 1Mbps 30~1000 5.77 -62.79 ≤-14.23 PASS 11B Ant1 2462 1Mbps 1000~26500 5.77 -49.92 ≤-14.23 PASS 11G Ant1 2412 6Mbps 0~Reference -0.01 -0.01 --- PASS 11G Ant1 2412 6Mbps 30~1000 -0.01 -62.24 ≤-20.01 PASS 11G Ant1 2412 6Mbps 1000~26500 -0.01 -49.98 ≤-20.01 PASS 11G Ant1 2437 6Mbps 0~Reference -0.07 -0.07 --- PASS 11G Ant1 2437 6Mbps 30~1000 -0.07 -61.43 ≤-20.07 PASS 11G A…

Text truncated - open the document above for the full version.