NCTSAGA1-DTransmitter

Model: SAGA1-D FCC ID: NCTSAGA1-D FEDERAL COMMUNICATIONS COMMISSION This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. I

The frequency here is 12.8MHz

FCC ID : NCTSAGA1-D FRONT SIDE OF EUT Number 1 0N2106-01.jpg FCC ID : NCTSAGA1-D REAR SIDE OF EUT Number 2 0N2106-02.jpg

EXHIBIT A. FCC ID LABEL FCC ID: NCTSAGA1-D The following statement will be placed in the User’s Manual. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC ID: NCTSAGA1-D 0.5CM 4CM Note: 1. Material and thickness:2 mi 1, white 2. Glue information : Permanent adhesive 3. Text color is black 4. Scale: 1:1

FCC ID: NCTSAGA1-D Label Location

FCC ID : NCTSAGA1-D Mechanical Construction Number 1 0N2106-03.jpg FCC ID : NCTSAGA1-D Mechanical Construction Number 2 0N2106-04.jpg FCC ID : NCTSAGA1-D Mechanical Construction (Reference Modification No.1) Number 3 0N2106-05.jpg 1 FCC ID : NCTSAGA1-D Front side of main board Number 4 0N2106-06.jpg FCC ID : NCTSAGA1-D Rear side of main board Number 5 0N2106-07.jpg FCC ID : NCTSAGA1-D Front side of circuit board Number 6 0N2106-08.jpg FCC ID : NCTSAGA1-D Rear side of circuit board Number 7 0N2106-09.jpg

Model : SAGA1-D FCC ID: NCTSAGA1-D

FCC ID : NCTSAGA1 - D FCC ID : NCTSAGA1 - D

FCC TEST REPORT Report No. : F0N2106 SPORTON International Inc. FCC ID : XXXSAGA1-D TEL : 886-2-2696-2468 Page No. : 1 of 24 FAX : 886-2-2696-2255 Issued Date : Apr. 24, 2001 FCC TEST REPORT for 47 CFR, Part 15, Subpart C Equipment : Industrial Radio Remote Controller (Transmitter) Model No. : SAGA1-D FCC ID : XXXSAGA1-D Filing Type : Certification Applicant : GAIN ELECTRONIC CO., LTD. 4F-1, No. 288-5, Hsin Ya Rd., Chien Chen Zone, KaoHsiung, Taiwan, R.O.C. ! The test result refers exclusively to the test presented test model / sample. ! Without the written authorization of the test lab., the Test Report may not be copied. ! Certificate or Test Report must not be used by the applicant to claim the product in this test report endorsement by NVLAP or any agency of U.S. government. SPORTON International Inc. 6F, No.106, Sec. 1, Hsin Tai Wu Rd., Hsi Chih, Taipei Hsien, Taiwan, R.O.C. FCC TEST REPORT Report No. : F0N2106 SPORTON International Inc. FCC ID : XXXSAGA1-D TEL : 886-2-2696-2468 Page No. : 2 of 24 FAX : 886-2-2696-2255 Issued Date : Apr. 24, 2001 Table of Contents CERTIFICATE OF COMPLIANCE.......................................................................................................3 1. General Description of Equipment under Test .................................................................................... 4 1.1. Applicant .................................................................................................................................................................................... 4 1.2. Manufacturer.............................................................................................................................................................................. 4 1.3. Basic Description of Equipment under Test ................................................................................................................................ 4 1.4. Feature of Equipment under Test ............................................................................................................................................... 4 2. Test Configuration of Equipment under Test ...................................................................................... 5 2.1. Test Manner............................................................................................................................................................................... 5 2.2. Description of Test System......................................................................................................................................................... 5 2.3. Connection Diagram of Test System .......................................................................................................................................... 6 2.4. A plot shows the EUT meet the requirement of 15.231(c)........................................................................................................... 7 3. Test Software....................................................................................................................................... 9 4. General Information of Test .............................................................................................................. 10 4.1. Test Facility.............................................................................................................................................................................. 10 4.2. Standard for Methods of Measurement .................................................................................................................................... 10 4.3. Test in Compliance with ........................................................................................................................................................... 10 4.4. Frequency Range Investigated................................................................................................................................................. 10 4.5. Test Distance ........................................................................................................................................................................... 10 5. Test of Conducted Powerline ............................................................................................................ 11 6. Test of Radiated Emission................................................................................................................. 12 6.1. Major Measuring Instruments ................................................................................................................................................... 12 6.2. Test Procedures....................................................................................................................................................................... 13 6.3. Typical Test Setup Layout of Radiated Emission...................................................................................................................... 14 6.4. Test Result of Radiated Emission............................................................................................................................................. 15 7. Antenna Factor & Cable Loss ........................................................................................................... 21 8. EMI Suppression Component List .................................................................................................... 22 9. List of Measuring Equipments Used................................................................................................. 23 10. Uncertainty of Test Site ................................................................................................................... 24 Appendix A. Photographs of EUT.............................................................................................. A1 ~ A5 FCC TEST REPORT Report No. : F0N2106 SPORTON International Inc. FCC ID : XXXSAGA…

Text truncated - open the document above for the full version.

FCC TEST REPORT Report No. : F0N2106 SPORTON International Inc. FCC ID : NCTSAGA1-D TEL : 886-2-2696-2468 Page No. : 1 of 1 FAX : 886-2-2696-2255 Issued Date : Feb. 5, 2001 1.1. Photographs of Radiated Emission Test Configuration l The photographs show the configuration that generates the maximum emission. FRONT VIEW REAR VIEW